Hi Guys,
I have a Ulefone Be Touch 1, all was going ok until it starts to get laggy and slow after a few restarts simple stopped switching on.
I have tried SP Flash tools and Odin but without success...the phone is dead
My computer when I plug It in makes the detection sound but nothing appears and the phone continues off.
My phone was rooted and I know its not the reason of being dead because I used it for almost 6 months with no problems.
When with SP flash tools if I try to install the boot and the recovery it gives me the : BROM ERROR : S_Storage_Not_Match (3167) is this a Hardware fault???
Any clue what can it be guys?
I'm almost ready to buy a new one...
Thanks
Related
Hey all,
In an attempt to load the custom ROM from http://forum.xda-developers.com/showthread.php?t=2658343 I kinda broke the phone.
Part of the steps is to flash the custom Recovery screen.
In the steps you use the Scatter file that's provided and load that up with the SP FlashTool.
Problem though is that I started to get the error SP FLASH TOOL ERROR : (8038).
I then read that by using MTK Droid Root & Tools, I could create a new Scatter file that would fix the error...
Created the new scatter file and then when I loaded it, I got the Big Green Circle saying everything was cool.
Rebooted the phone and it wouldn't come back on.
Crap.
Tried loading into the Recovery screen using the volume and power button, but nothing shows up on the screen.
Tried plugging it into my Win7 and WinXP computers but neither recognize the device and nothing shows up on the screen to say that it's charging.
Is this phone completely gone or is there something that can be done?
Old thread but somehow connected brand new experience to be documented:
What I just experienced was, after a cancelled attempt of flashing recovery, the phone was off and didn't go back on. I tried fiddling with the buttons and assumed it was bricked. Fortunately I didn't give up too soon. It was only after pressing the on button for a very extended time (>30secs?) that it came back to life. It didn't boot further than Wiko logo, but the key reactions were back to normal concerning reboot, booting recovery and cold start.
i have a tecno f8 device, it has MT6589 processor. The phone hanged one time and i forced restart it holding down the power button for about 10secs, unfortunately when the phone restarts, it kept coming on and off, and here is where i think i bricked the phone, the phone's battery was at 10%..i pulled the battery and loaded the cmw recovery plugged in the charger, and i tried reflashing my custom rom (miui v5).. the rom installed completely.. then i went to 'reboot now' from the cmw menu options, and then my phone refused to come on, its just dead, led light wont even come on if i plug the charger, and i cant boot into recovery.
i have been to a number of android developmental blogs trying to solve this issue, i even download the stock firmware and i tried flashing with sp flash tools, but i keep getting various brom errors, the 3149, 5069 no space errors.
can anyone pls help me get my phone back on?
i was getting some problems with the samsung galaxy s4 clone mt6575 version ,the phone was going into the bootloop ,i could see only the android logo during the phone boot and the phone would become stuck so i googled on how to flash the phone and got some instructions .
here are the steps i followed
1.i downloaded the stock firmware for the mt6575 version
2.downloaded spflashtool
3.selected the scatter file from the downloaded firmware
4.clicked the download button and connected my phone ,i was constantly getting errors like emmc error but i tried again and again
5.at the middle of flashing ,got some error and the phone became dead and never came back
6.i tried reinstalling the drivers but the phone was not detected by the pc as it was detected before
7.but i could feel the phone was working since the camera portion was very warm as if i was gaming on the phone.
any solutions to bring back the phone to life ,the phone shows no display or any response when press the power button even when i pulled out the battery and connected the device the pc didn't detect the device.
Hi, I have the BLU Energy X, and I had flashed some ZIP mods via TWRP. I decided that I didn't want them, and read somewhere that I had to flash my phone using the stock ROM. I used the ROM from NeedRom here: needrom[.com]/ download/ blu-energy-x-e010q which should be the correct one for my phone. It also shows the . I installed proper drivers and flashed using smartphone flash tool. It completed, and I unplugged my phone and pressed the power button. Nothing happened. No combination of power and volume buttons turn this phone on. I have tried flashing again, and I got the error "BROM ERROR : S_FT_ENABLE_DRAM_FAIL (0xFC0)". My phone does show up in Device Manager when I plug it in, as USB Serial Device (COM6) under the Ports category. Sometimes it will go in a loop of SHowing up then 3-5 seconds disconnecting from PC, then connecting again. Before I flashed I used the format option because I was getting an error, and that was the fix for it. The flash completed successfully. I did not touch the device while it was flashing, or the USB cable. I'm in grade 8 and I get a really allowance, so I couldn't buy this phone for about 8-10 months again, and I really want to avoid that. I am/was rooted, if that helps. Thanks everyone here in advance, and I really hope you guys know how to fix this! Thanks alot
Hi,
My friends oppo neo 5 went into bootloop and we decided to flash stock rom to solve it. We had done the same previously and it worked without any problems. This time after initially flashing it stayed on the boot screen itself and we decided to flash again but this time instead of download on the sptool, we used firmware upgrade and after flashing, the phone wont boot up. when we try to power it on it vibrates for 2-3 seconds and then continues to vibrate after an interval. The phone is detected in device manager when its plugged in to the pc as mediatek usb port and mediatek da usb vcom. The phone is detected in sptool and we are able to flash and it gives the green tick, but there is no use as the phone wont boot up.