i was getting some problems with the samsung galaxy s4 clone mt6575 version ,the phone was going into the bootloop ,i could see only the android logo during the phone boot and the phone would become stuck so i googled on how to flash the phone and got some instructions .
here are the steps i followed
1.i downloaded the stock firmware for the mt6575 version
2.downloaded spflashtool
3.selected the scatter file from the downloaded firmware
4.clicked the download button and connected my phone ,i was constantly getting errors like emmc error but i tried again and again
5.at the middle of flashing ,got some error and the phone became dead and never came back
6.i tried reinstalling the drivers but the phone was not detected by the pc as it was detected before
7.but i could feel the phone was working since the camera portion was very warm as if i was gaming on the phone.
any solutions to bring back the phone to life ,the phone shows no display or any response when press the power button even when i pulled out the battery and connected the device the pc didn't detect the device.
Related
I've been trying to fix this phone for about a week now with hardly any luck.
Problem: When pressing the power button to turn phone on, there is no samsung boot logo. the only thing that shows up is a black screen, [the backlight] it will stay that way until the battery dies.
i know it's not a problem with the display because i can get to the recovery screen by pressing the three buttons. i tried numerous wipes and factory resets, even tried to reboot from there. but it still wont boot up, it only ends up with that black screen. Also the green battery shows which further indicates that it's not a display problem.
Phone Description:
Model: GT-I9500
FCC ID: A3LGTi9500
SSN:-i9500GSMH
RATED:3.85V===:13 00mA
MADE IN KOREA BY SAMSUNG
IMEI:355236030
S/N:R21D48HDDA
That's basically all i know about this phone, not sure what mtk version it is either, i know it's a clone because on the hardware differences under the hood compared to the real S4. also it shows mt65xx [i installed the driver for it btw] when connected at battery screen.
[it's probably a legend or a superking since it's from korea i think]
Some things i've tried: i downloaded android SDK, MTK droid tools, SP FLash tools, for some reason, i keep getting error 8200 in sp flash tools and mtk droid tools doesn't detect my phone.
I tried flash updating firmware with adb sideload, it always ends up with an error ''aborted''. i can't enable usb debugging since the phone wont turn on.. :/,
Also can i make it work with a stock recovery img. or something?
Attached: battery screen, recovery screen, when the phone is powered on, after battery pull.
Can anyone help me?
Hi Guys,
I have a Ulefone Be Touch 1, all was going ok until it starts to get laggy and slow after a few restarts simple stopped switching on.
I have tried SP Flash tools and Odin but without success...the phone is dead
My computer when I plug It in makes the detection sound but nothing appears and the phone continues off.
My phone was rooted and I know its not the reason of being dead because I used it for almost 6 months with no problems.
When with SP flash tools if I try to install the boot and the recovery it gives me the : BROM ERROR : S_Storage_Not_Match (3167) is this a Hardware fault???
Any clue what can it be guys?
I'm almost ready to buy a new one...
Thanks
So let me explain how i soft bricked it and what I tried.
--How it all happened--
So first yesterday I rooted my Galaxy S6 Edge G925F with CF Auto Root. I tried to install Xposed (it was Xposed installer i think) from Google Play. Before clicking install the app said "During the install your phone may become unusable and you may never can use it" or some kind of that. I clicked install and that's all. My phone restarted and it was stuck on a black screen. After 2-3 minutes the Samsung logo appeared and it was stuck there. I had 20% battery and left it on the Samsung logo and left it for the night to see would it load.
--What I've tried--
On the next morning the phone was shut down. I plug it in the charger and let it load to at least 5% of battery. I could put the phone on bootleg or download mode and after a little bit of research i found out that my phone was soft bricked. I did a factory reset and deleted the cache but this didn't helped. I tried to stock ROM from Odin v.3.09 and v.3.10.6 it with Android 5.1 but there was an error I think when it came to hidden.img. As of now I found out that i could've deleted that file from the firmware but then i didn't knew that. So coming to the next step I tried with firmware of Android 6.1 but otherwise it didn't load or it got to the same error as of the Androd 5.1 . I started thinking what could stop the installation process. I tried instead of plugging the cable in the USB 2.0 hub to put it into the USB 3.0 hub but that didn't worked as well. I tried with another cables but that gave the same errors. I had Samsung Kies, Kies 3, Smart Switch and SideSync. I thought i may uninstall them because their drivers may conflict with the Samsung drivers I installed earlier. While my phone was in Download mode, Odin detected it as 0:[COM15] but in Kies it says "your phone is not in the list of the allowed models please visit the list of allowed models" or some kind of that. I tried to use recovery mode in Kies but my computer was not detecting the phone as Galaxy S6 Edge.
--The solution--
1. Install Samsung USB drivers
2. Install Samsung Kies or Kies 3( I don't remember try with the both versions)
3. Put your phone in download mode by holding down the power button, volume down key and the home button.
4. Open Samsung Kies and go to Tools>Firmware Upgrade and Initialisation
5. Enter you Samsung model and S/N (Serial Number) (you can see it on the back of your phone)
6. Wait Kies to download and install the firmware
7. You're all set. All your data is erased but at least you have unbricked your phone and you have learnt your lesson!
I have a very exaggerated problem for this device, the first time I gave Stock ROM through Download Mode, it started, I went to lunch, when I came back he had given a (Blocked Writing) error in the middle of the process, now at that moment I know how to solve this problem, but as I did not know, I tried to flash ROM again in Odin, and every time I was locking in aboot.mbn, after several attempts, several different computers, different USB cables ... different tests, now in this exact Odin crashes in Initialization, does not leave there for nothing, leave a long time it says that the device did not respond, I tried to reestablish the PIT that is the Partition Table using Odin, however it hangs anyway in initialization, I researched a lot, I tried Unbrick methods through files on SD Card, tried several Rom Stock and also tried to install a Custom Recovery, however everything fails, after all, in all cases it crashes in initialization, hey sso not only happens in a single System, then I decreed this cell phone as deceased .. the ****ing thing died, I saw in some places that they said that the problem was Hard Brick, that is to say, problem in the motherboard parts, and the solution would be change the motherboard of the entire device, but this is very expensive ...
Sansung Kies is only connecting and after a while he says that the device did not respond, if I turn the phone on, and do nothing, it goes to a Download screen only instead of the green android in the middle, a message appears talking to do Firmware Upgrade using Sansung Kies, and if I hold the buttons to enter the recovery mode, nothing happens and it's the same thing to turn it on normally, and if I hold the Download Mode buttons, it goes into Download Mode normally only in both cases Odin locks in initialization ..
Model: Samsung GT-I9192 Galaxy S4 Mini Duos
Hi,
My friends oppo neo 5 went into bootloop and we decided to flash stock rom to solve it. We had done the same previously and it worked without any problems. This time after initially flashing it stayed on the boot screen itself and we decided to flash again but this time instead of download on the sptool, we used firmware upgrade and after flashing, the phone wont boot up. when we try to power it on it vibrates for 2-3 seconds and then continues to vibrate after an interval. The phone is detected in device manager when its plugged in to the pc as mediatek usb port and mediatek da usb vcom. The phone is detected in sptool and we are able to flash and it gives the green tick, but there is no use as the phone wont boot up.