Related
I flashed my xperia s with recovery.img and then disconnected the cable. Then i tried turning it on from the power button nothing was displayed on the screen. So how do i boot my xperia s in the recovery mode so that i get an option "wipe data/factory reset"?
Turn on the phone and keep pressing volume up
Sent from my Xperia S using xda premium
or...
bhanujallandhra said:
I flashed my xperia s with recovery.img and then disconnected the cable. Then i tried turning it on from the power button nothing was displayed on the screen. So how do i boot my xperia s in the recovery mode so that i get an option "wipe data/factory reset"?
Click to expand...
Click to collapse
Reboot and as soon as Sony logo appears press the screen a few times (sometimes its better to keep pressing until it appears, to save trying again):good::fingers-crossed:
Still stuck
smallz2k said:
Reboot and as soon as Sony logo appears press the screen a few times (sometimes its better to keep pressing until it appears, to save trying again):good::fingers-crossed:
Click to expand...
Click to collapse
I tried all the methods but none of the above works. as soon as i flash my fone with the recovery image the and disconnect it from the usb cable and try turnin it on. it doesnt turn on. theres no sony logo. Please help what shall i do?? i want to root my fone with stock kernel only dont want to root it by custom roms.
:crying:
bhanujallandhra said:
I flashed my xperia s with recovery.img and then disconnected the cable. Then i tried turning it on from the power button nothing was displayed on the screen. So how do i boot my xperia s in the recovery mode so that i get an option "wipe data/factory reset"?
Click to expand...
Click to collapse
I think this recovery.img was not walid... I did that with my phone too, and nothing appear in screen. U have to flash another kernel (i suggest, the doomlords kernel). After that turn on the phone, and press the volume up, when doomlord logo appears.
hope it helps.
How are you getting on is your phone back on?
Sent from my LT26i using xda premium
---------- Post added at 03:24 PM ---------- Previous post was at 03:19 PM ----------
If you tried the methods above with no joy it obviously isn't installed. With the cwm you are trying is there a .bat file in the download on your computer. If so while your phone is plugged into PC run the bat file and follow onscreen instructions. Then try launching cwm again.If you havnt managed it yet leave a message and I'll find it.
Sent from my LT26i using xda premium
I am posting here as I am facing the same problem.
I have been following this guide to flash my phone with CM10 from ICS stock rom.
h#ttp#://androidlegend.com/xperia-s-update-to-android-4-1-jelly-bean-with-cyanogenmod-10/
I have successfully followed everything done previously, including Unlocking the bootloader, getting root access, installing busybox, using RecoverX to install CWM.
I copied the FXP150-cm-10.1-20121209-UNOFFICIAL-mint.zip to sdcard, is it this that is required to flash to ROM or the boot.img that is inside the zip?
And I am stuck on that part where I have to reboot into recovery mode. I have tried
a) Connecting my phone and opening fastboot mode and then try to keep the vol up pressed to open recovery mode.
b) Without connecting, powering my phone on and pressing volume up. But there is no blue LED
c) Without connecting, powering my phone on and continuously tapping on sony logo. After that Xperia logo.
But I can not enter the recovery mode.
A little guidance please?
Flashing CM needed a seperate kernel. Keep following the instructions to use fastboot to flash the boot.img
Power the phone off. Hold vol + then plug the USB cable in. There should be a blue light.
Poorly written tutorial IMO. Should be flashing kernel first then the rom to save some panic.
I asked the Sony-Support, they say that there is no recovery-mode.(for Xperia U, but they are the "same")
dirtydevil783 said:
I am posting here as I am facing the same problem.
I have been following this guide to flash my phone with CM10 from ICS stock rom.
h#ttp#://androidlegend.com/xperia-s-update-to-android-4-1-jelly-bean-with-cyanogenmod-10/
I have successfully followed everything done previously, including Unlocking the bootloader, getting root access, installing busybox, using RecoverX to install CWM.
I copied the FXP150-cm-10.1-20121209-UNOFFICIAL-mint.zip to sdcard, is it this that is required to flash to ROM or the boot.img that is inside the zip?
And I am stuck on that part where I have to reboot into recovery mode. I have tried
a) Connecting my phone and opening fastboot mode and then try to keep the vol up pressed to open recovery mode.
b) Without connecting, powering my phone on and pressing volume up. But there is no blue LED
c) Without connecting, powering my phone on and continuously tapping on sony logo. After that Xperia logo.
But I can not enter the recovery mode.
A little guidance please?
Click to expand...
Click to collapse
Snowstormzzz said:
Flashing CM needed a seperate kernel. Keep following the instructions to use fastboot to flash the boot.img
Power the phone off. Hold vol + then plug the USB cable in. There should be a blue light.
Poorly written tutorial IMO. Should be flashing kernel first then the rom to save some panic.
Click to expand...
Click to collapse
MasterBolle said:
I asked the Sony-Support, they say that there is no recovery-mode.(for Xperia U, but they are the "same")
Click to expand...
Click to collapse
Guys, dont ask Sony cause stock ROM doesnt have recovery.
If you want to flash CM you must fastboot the boot.img inside the zip file, before that put the ROM into your phone memory, power on the phone and keep pressing vol up, enter into CM recovery and flash rom from phone memory. Wipe before and after.
Agree, stock ROM doesn't have Recovery Mode. When you turn your phone with VOL_UP, nothing happens :cyclops:
bhanujallandhra said:
I flashed my xperia s with recovery.img and then disconnected the cable. Then i tried turning it on from the power button nothing was displayed on the screen. So how do i boot my xperia s in the recovery mode so that i get an option "wipe data/factory reset"?
Click to expand...
Click to collapse
try flashing it again, maybe your first flash had an error.
Met the same problem and here what I did:
-Take off the battery in 10 minutes and put it back
-Plug the charger into the phone and do the logging in CWM steps (press and hold the volumme up, press the power button).
Finally it worked, hope this can help
please help!
i was flashing the official pacman rom for xperia u. then i connected my phone to the computer to fastboot the cm kernel.
but the flashtool says that drivers need to be installed. i have installed the drivers but the problem still persists.
i tried to goto the cwm but after i keep pressing the vol down button, the led flashes but nothing comes. its a black screen.
now i'm not able to do anything to the phone not even abble to flash stock ftf!
Please help!
vinayakagarwal1996 said:
please help!
i was flashing the official pacman rom for xperia u. then i connected my phone to the computer to fastboot the cm kernel.
but the flashtool says that drivers need to be installed. i have installed the drivers but the problem still persists.
i tried to goto the cwm but after i keep pressing the vol down button, the led flashes but nothing comes. its a black screen.
now i'm not able to do anything to the phone not even abble to flash stock ftf!
Please help!
Click to expand...
Click to collapse
Press volume up | power key untill you feel 3 vibrations then try to power up again.
EDIT: have you installed flash mode and fastboot drivers mode drivers too?
ChikeD said:
Press volume up | power key untill you feel 3 vibrations then try to power up again.
EDIT: have you installed flash mode and fastboot drivers mode drivers too?
Click to expand...
Click to collapse
Or remove the battery you may need to open pc device manager and manualy uninstall the drivers and make sure u manualy install the right ones
Sent from my Xperia U using xda app-developers app
ChikeD said:
Press volume up | power key untill you feel 3 vibrations then try to power up again.
EDIT: have you installed flash mode and fastboot drivers mode drivers too?
Click to expand...
Click to collapse
i tried but felt only 1 vibration which powered up the device and got stuck on kernel.
vinayakagarwal1996 said:
i tried but felt only 1 vibration which powered up the device and got stuck on kernel.
Click to expand...
Click to collapse
Wait untill you feel 3 vibrations.
What firmware you had when you installed the rom and can you give the link to the thread of the rom you installed?
Do you have ftf to original formware?
One vibration reboot, three power off.
After you will switch off, try flash tft then.
Sent from my Xperia Sola using xda app-developers app
ChikeD said:
Wait untill you feel 3 vibrations.
What firmware you had when you installed the rom and can you give the link to the thread of the rom you installed?
Do you have ftf to original formware?
Click to expand...
Click to collapse
Actually before that i was trying to port a rom but it didnt work out.
so i flashed the pacman rom http://forum.xda-developers.com/showthread.php?t=2372433
in this i had to fastboot the boot.img which i then was unable to.
and before that i had the same rom installed. i have the original ftf.
i instaled the latest flashtool. it says the drivers arent installed but they are.
windows says unable to install drivers.
after i press the vol up and power, after 1 vibration it goes to kernel. i waited for 5 min pressing the buttons but nothing happened.
when on kernel, flashtool says device connected in usb debugging off.
Thanks for your help!
in the flashtool, i chose the log level to debug.
then my phone was able to get to the fastbot mode and i successfully fastbooted the correct cm kernel and booted up the rom!
vinayakagarwal1996 said:
Actually before that i was trying to port a rom but it didnt work out.
so i flashed the pacman rom http://forum.xda-developers.com/showthread.php?t=2372433
in this i had to fastboot the boot.img which i then was unable to.
and before that i had the same rom installed. i have the original ftf.
i instaled the latest flashtool. it says the drivers arent installed but they are.
windows says unable to install drivers.
after i press the vol up and power, after 1 vibration it goes to kernel. i waited for 5 min pressing the buttons but nothing happened.
when on kernel, flashtool says device connected in usb debugging off.
Click to expand...
Click to collapse
Did you replace the kernel image before installing? Realy weird why the didn't fo it themselves.
No ppoint to try booting the phone.
You have removable battery so try to remove it for a minute, put it back and see if you can connect in flash mode and flash original formware.
BTW what do you mean by "goes to kernel?" recovery?
ChikeD said:
Did you replace the kernel image before installing? Realy weird why the didn't fo it themselves.
No ppoint to try booting the phone.
You have removable battery so try to remove it for a minute, put it back and see if you can connect in flash mode and flash original formware.
BTW what do you mean by "goes to kernel?" recovery?
Click to expand...
Click to collapse
sorry. i may be wrong. i meant the first image that comes when you boot like fxp logo/sony/samusung logo
btw i have fixed the problem as stated in my above post.
and i have now reflashed it.
Hey Guys!
So I have an Xperia P, and ever since I upgraded to JB, I have been having several problems. The system lags a LOT. I cannot see any pictures in my Album, though the pictures are there, when I try calling someone it lags so much that the process ends. And it lags a lot when I try picking up such that I can't hear what they're saying for upto 5 seconds. Either that, or it just ends
So I've been attempting to flash a custom OS, but I've been facing some problems. I have rooted my Xperia. When I went on the xda forum to get the flashboot drivers, the link is dead. I installed them from another source.
When I turn off my phone and I hold the power up button, the blue LED light comes on and I go to device manager to install the custom drivers from the SDK bundle. By that time, my phone's blue LED light wouldve gone and the drivers aren't installed. At least I don't think it has. Soo I really need your help on installing the fastboot drivers and unlocking bootloader so I can flash a custom OS. Please help.
Thanks in advance
GokuSS1
GokuSS1 said:
Hey Guys!
So I have an Xperia P, and ever since I upgraded to JB, I have been having several problems. The system lags a LOT. I cannot see any pictures in my Album, though the pictures are there, when I try calling someone it lags so much that the process ends. And it lags a lot when I try picking up such that I can't hear what they're saying for upto 5 seconds. Either that, or it just ends
So I've been attempting to flash a custom OS, but I've been facing some problems. I have rooted my Xperia. When I went on the xda forum to get the flashboot drivers, the link is dead. I installed them from another source.
When I turn off my phone and I hold the power up button, the blue LED light comes on and I go to device manager to install the custom drivers from the SDK bundle. By that time, my phone's blue LED light wouldve gone and the drivers aren't installed. At least I don't think it has. Soo I really need your help on installing the fastboot drivers and unlocking bootloader so I can flash a custom OS. Please help.
Thanks in advance
GokuSS1
Click to expand...
Click to collapse
Which Windows version are you using? If you are using Windows 7 then try this:-
Download this ZIP File.
Extract the contents on Desktop
Now Open Device Manager by RIGHT CLICKING ON MY COMPUTER>MANAGE>DEVICE MANAGER
Now connect your phone in fastboot mode to the PC by holding the Vol + button while plugging in the cable.
You will see a new device in the device manager with an error sign on it. Instantly double click on that because it will disappear as the blue LED disappears.
A dialog box will open. Disconnect the phone and dont connect it.
Go to drivers tab
Click on update driver.
Now select BROWSE MY COMPUTER FOR DRIVER SOFTWARE
Now select LET ME PICK FROM A LIST OF DEVICE DRIVERS ON MY COMPUTER
Now select HAVE DISK
Now click on browse.
Open the extracted folder and select the android_winusb.inf
Click OK
Select the ADB driver from the updated list.
Now connect the phone again in fastboot mode again.
And then click on NEXT. You have to do this very quickly because as soon as the BLUE LED disappears the driver will not load but it will show that it is loaded.
Try This, If fails, tell me, will tell you other method.
pass oturse
Never Mind, I got it to work
But thanks anyways!!
I have another problem now. Since I unlocked bootloader, when I turn my phone off, it automatically turns back on, but after the sony kogo appears, nothing more happens, the screen is still in use, a faint light comes off of it, but it's blank and black. I had to wait for it to run out of charge so i could turn it back on. Any help?
What version of JB you got?
Even that'sresolved now... Guess that the custom OS was just starting up
I have one more though... Hopefully the last one! I tried flashing a stock ROM - ICS for Xperia P (LT22i) with flashboot. It prepared the filesand the pop-up came asking me to turn it off, press and hold the flashboot button and connect it to the USB. The blue LED light came but it never flashed. In the log it also came that a flashboot device has been connected. Help please!
Thanks in advance,
Goku
GokuSS1 said:
Even that'sresolved now... Guess that the custom OS was just starting up
I have one more though... Hopefully the last one! I tried flashing a stock ROM - ICS for Xperia P (LT22i) with flashboot. It prepared the filesand the pop-up came asking me to turn it off, press and hold the flashboot button and connect it to the USB. The blue LED light came but it never flashed. In the log it also came that a flashboot device has been connected. Help please!
Thanks in advance,
Goku
Click to expand...
Click to collapse
U pressed fastboot button so blue LED came and it wont flash.........
try entering flash mode by pressing vol down while pluggi in usb u shud get green light den flashing starts...........
Install flashboot drivers before flashing
:good::good:
GokuSS1 said:
Even that'sresolved now... Guess that the custom OS was just starting up
I have one more though... Hopefully the last one! I tried flashing a stock ROM - ICS for Xperia P (LT22i) with flashboot. It prepared the filesand the pop-up came asking me to turn it off, press and hold the flashboot button and connect it to the USB. The blue LED light came but it never flashed. In the log it also came that a flashboot device has been connected. Help please!
Thanks in advance,
Goku
Click to expand...
Click to collapse
Flashing ROM in flash mode not fastboot.
how do i do that?
EDIT: I know, lame question... But I'm new to this stuff
GokuSS1 said:
how do i do that?
Click to expand...
Click to collapse
Hold volume down while connecting to ISB., phone turned off of course.
kalyan_kadari said:
U pressed fastboot button so blue LED came and it wont flash.........
try entering flash mode by pressing vol down while pluggi in usb u shud get green light den flashing starts...........
Install flashboot drivers before flashing
:good::good:
Click to expand...
Click to collapse
Thanks!!!!
sorry I hadn't seen it!
where do i get flashmode drivers from?
GokuSS1 said:
where do i get flashmode drivers from?
Click to expand...
Click to collapse
Install fastboot and flash mode drivers with the installer in flashtool directiry (drivers).
i was using some jelly bean sony rom by divaksh (it had cwm touch) and i wanted to try the new cm10.2 rom by munjeni
i downloaded the cm10.2, put it on my external sd card through a usb micro-sd reader and then put the µsd back in the phone
i selected "reboot to recovery" from the phone's power menu (i had an xposed module for more power menu options)
then i noticed that the phone didn't reboot, but it had turned off completely
i held the power button and the phone vibrated but didn't power on
it powered on on the second try, i then went to the cwm recovery by tapping the volume down key
(i was going to make a backup of the current system, but i forgot it lol)
i flashed the cm10.2 zip (cm10.2_pepper-ota-eng.root_Build.1.zip) without doing any wipes, because i wanted to get to the correct version of cwm recovery
(i would've properly done the wipes/formats from the cwm recovery that is in the cm10.2 kernel)
it finished flashing the zip and i rebooted my phone, but then it didn't power on anymore
now when i hold down the power button, the phone makes a short vibration but nothing else
.
if i plug the phone to a charger, the led lights up (red) for approximately a second and then turns off
if i hold down "volume-down" and the power button, the phone vibrates once and flashes the led (green)
i've tried going into flashmode and fastboot mode but the light doesn't stay on for long and sony mobile flasher doesn't even notice the phone even though the drivers are installed
the "hold down power button and vol-up"-thing also works but it doesn't seem to do anything else than vibrate
what should i do?
Is your bootloader unlocked?
If yes then flahs
Sent from my LT22i using XDA Premium 4 mobile app
Hamza Murad said:
If yes then flahs
Click to expand...
Click to collapse
what?
Is it unlocked?
When I bricked my xperia p I flashed a custom kernel which allowed me to enter Cwm and then flashed the stock rom. I am new to this flashing thing so I recommend that you ask someone experienced what to do. I just shared my experience of recovering from a softbrick. Don't flash new things blindly but ask someone experienced before doing so.
Sent from my LT22i using XDA Premium 4 mobile app
the bootloader is unlocked, and i'm not new to this "flashing thing"
anyone? the phone still hasn't woken up
download firmware for your p and flash using flashtool...
Osku958 said:
the bootloader is unlocked, and i'm not new to this "flashing thing"
Click to expand...
Click to collapse
Have you used flashtool to flash firmware before on that PC?
Have you installed flashtool and it's drivers (sola, flash & fastboot mode).?
Make sure the phobe is off, press power + volume up untill you feel 1 + 3 vibrations and see if it stay in flash mode longer.
Just Flash stock
i have nearly the same problem
my xperia u was running with 4.1 then i restored my ta backup its mine not for someone else then i pressed reboot instead of power off then my phone is dead no vibration no led except the one when i plug it to charger just one red led then nothing
AndroidNoob69 said:
Just Flash stock
Click to expand...
Click to collapse
how? the phone doesn't boot and flashtool doesn't recognize it
Same problem here, I think that Munjeni's post is bad written.
Ok, I fixed it, follow my instructions as they goes. You have to flash the .img kernel that CM10.2.zip comes from.
For flashing it, go as follows...
First try to install the following drivers, with Flashtool. The executable is in C:\\Flashtool\drivers
Run as adminsitrator and follow screen instructions, allow any driver install.
When it's ready, try to plug in the phone in fastboot mode (turn off, hold power and vol up and release power button, led has to turn blue/violet/pink, whatever, a color like that)
Run flashtool.
Flashtool will recognize the phone as the log says, if its not try to install drivers mannually.
If it's recognized then click the black lightning button and select fast boot mode.
At the right side click "Select kernel to flash" and browse the kernel that comes in the .zip. (in the file you've downloaded you have to extract a boot.ini because is the main kernel to make the ROM work, so you have to put somewhere else, I prefer desktop)
When selected, log writes all the procedure until it show an "OKAY[time]" message.
Finally click "Reboot device into system" in the center side and wait until boots.
It should be working now, I spent a lot of hours investigating, but finally I fixed, hope it works for you too!
If there's an error or some question, feel free to post.
manudo said:
Ok, I fixed it, follow my instructions as they goes. You have to flash the .img kernel that CM10.2.zip comes from.
For flashing it, go as follows...
First try to install the following drivers, with Flashtool. The executable is in C:\\Flashtool\drivers
Run as adminsitrator and follow screen instructions, allow any driver install.
When it's ready, try to plug in the phone in fastboot mode (turn off, hold power and vol up and release power button, led has to turn blue/violet/pink, whatever, a color like that)
Run flashtool.
Flashtool will recognize the phone as the log says, if its not try to install drivers mannually.
If it's recognized then click the black lightning button and select fast boot mode.
At the right side click "Select kernel to flash" and browse the kernel that comes in the .zip. (in the file you've downloaded you have to extract a boot.ini because is the main kernel to make the ROM work, so you have to put somewhere else, I prefer desktop)
When selected, log writes all the procedure until it show an "OKAY[time]" message.
Finally click "Reboot device into system" in the center side and wait until boots.
It should be working now, I spent a lot of hours investigating, but finally I fixed, hope it works for you too!
If there's an error or some question, feel free to post.
Click to expand...
Click to collapse
That was "the long run" for windows-guys.
For Linux - no drivers needed anyways - just download fastboot from anywhere and look for kernel. Put them in a personal directory. Open and run in a terminal (some have to be login as su) "fastboot flash boot kernel.img" (or whatever kernel is called...), plug phone in usb, while press and hold power and volume-up buttons. Blue LED comes shining and terminal tell you the flashing.
Unplug or type "fastboot reboot" to re-start phone.
Sure, you also can use FlashTool, too. But for only flashing a kernel it is not needed. Only for flashing stockrom ftf. But this is another story.
i happens to me yesterday
Hi ! Dont worry u r not the first to face this problem i also face this problem yesterday.. my phone was on JB 4.1.2 i download custom ICS rom and install it through CWM Recovery mode, when my new custom Rom starts it stucks on Boot screen and then nothing happens i tried but my phone was in danger... i was worried then i install flash tool and downlaod ICS Rom for Flastool and install that after severals trys i was now ion ICS v4.0.4..
Just Press volume up key and power simultanly when phone vibrtes three time leave it for 30 sec. and then run Flashtool and follow step to install another or same Rom for Falshtool & You r Done ...:good: Sorry for my bad english and type mistakes...
Osku958 said:
i was using some jelly bean sony rom by divaksh (it had cwm touch) and i wanted to try the new cm10.2 rom by munjeni
i downloaded the cm10.2, put it on my external sd card through a usb micro-sd reader and then put the µsd back in the phone
i selected "reboot to recovery" from the phone's power menu (i had an xposed module for more power menu options)
then i noticed that the phone didn't reboot, but it had turned off completely
i held the power button and the phone vibrated but didn't power on
it powered on on the second try, i then went to the cwm recovery by tapping the volume down key
(i was going to make a backup of the current system, but i forgot it lol)
i flashed the cm10.2 zip (cm10.2_pepper-ota-eng.root_Build.1.zip) without doing any wipes, because i wanted to get to the correct version of cwm recovery
(i would've properly done the wipes/formats from the cwm recovery that is in the cm10.2 kernel)
it finished flashing the zip and i rebooted my phone, but then it didn't power on anymore
now when i hold down the power button, the phone makes a short vibration but nothing else
.
if i plug the phone to a charger, the led lights up (red) for approximately a second and then turns off
if i hold down "volume-down" and the power button, the phone vibrates once and flashes the led (green)
i've tried going into flashmode and fastboot mode but the light doesn't stay on for long and sony mobile flasher doesn't even notice the phone even though the drivers are installed
the "hold down power button and vol-up"-thing also works but it doesn't seem to do anything else than vibrate
what should i do?
Click to expand...
Click to collapse
akkufix said:
That was "the long run" for windows-guys.
For Linux - no drivers needed anyways - just download fastboot from anywhere and look for kernel. Put them in a personal directory. Open and run in a terminal (some have to be login as su) "fastboot flash boot kernel.img" (or whatever kernel is called...), plug phone in usb, while press and hold power and volume-up buttons. Blue LED comes shining and terminal tell you the flashing.
Unplug or type "fastboot reboot" to re-start phone.
Sure, you also can use FlashTool, too. But for only flashing a kernel it is not needed. Only for flashing stockrom ftf. But this is another story.
Click to expand...
Click to collapse
If I wrote for Windows 8 there will be more than that, believe me. Managing Android with Linux is a lot easier, from flashing to programming.
But, face it, Windows is the standard here.
manudo said:
If I wrote for Windows 8 there will be more than that, believe me. Managing Android with Linux is a lot easier, from flashing to programming.
But, face it, Windows is the standard here.
Click to expand...
Click to collapse
That's why i'm working over 8 years till now with Linux.
my xperia device is stuck on the sony logo. wont pass that part. doesn't go into flashmode or fastboot, nothing. what can I do plz I need help. cant use flashmode on the pc as the computer never recognizes the phone bcuz it doesn't go into fastboot mode.
If your phone even starts, then fastboot and flashmode should work just fine. What's the last thing you did before it wouldn't boot?
1. Hold VOL UP while plugging it in the USB on your computer. The LED should get blue
2. Either use fastboot through command-line or use QuickIMG to boot a custom kernel with recovery.
3. Flash or restore a ROM
Klaos3000 said:
If your phone even starts, then fastboot and flashmode should work just fine. What's the last thing you did before it wouldn't boot?
1. Hold VOL UP while plugging it in the USB on your computer. The LED should get blue
2. Either use fastboot through command-line or use QuickIMG to boot a custom kernel with recovery.
3. Flash or restore a ROM
Click to expand...
Click to collapse
I was trying to unroot the phone to go back to stock and update to stock lollipop. the led lights don't light up anymore, holding volume up or down doesn't do anything as soon as I plug in the usb cable the screen comes on and it stays on the sony logo.
antrax360 said:
my xperia device is stuck on the sony logo. wont pass that part. doesn't go into flashmode or fastboot, nothing. what can I do plz I need help. cant use flashmode on the pc as the computer never recognizes the phone bcuz it doesn't go into fastboot mode.
Click to expand...
Click to collapse
Do the following exactly as outlined.
1- with the phone DISCONNECTED from your pc or charger, hold the power and up buttons until it vibrates and turns off.
2- open the flashtool and select an ftf to flash, and wait for the message that asks you to connect the phone in flash mode.
3- the phone must still be off. Hold the down button and connect the phone to the usb port in the pc. The flashing will start.
I tried that it goes back to the sony logo.
najoor said:
Do the following exactly as outlined.
1- with the phone DISCONNECTED from your pc or charger, hold the power and up buttons until it vibrates and turns off.
2- open the flashtool and select an ftf to flash, and wait for the message that asks you to connect the phone in flash mode.
3- the phone must still be off. Hold the down button and connect the phone to the usb port in the pc. The flashing will start.
Click to expand...
Click to collapse
I tried that. Doesnt work
antrax360 said:
I was trying to unroot the phone to go back to stock and update to stock lollipop. the led lights don't light up anymore, holding volume up or down doesn't do anything as soon as I plug in the usb cable the screen comes on and it stays on the sony logo.
Click to expand...
Click to collapse
How did you try to unroot? It's weird if you don't have working fastboot or flashmode, and without those, you're pretty much screwed. Those two should work even if you screw up big-time, like flashing a wrong kernel, but you must have done something weird if they stopped working?
And let me get this straight, you are pressing and HOLDING the volume buttons when you plug it to your computer, right? Make sure that the device is completely off by pressing and holding POWER + VOL UP. It'll vibrate a couple of times. Note that you're not supposed to be connected to the computer, since it'll then just boot again.
Then press and HOLD VOL UP for fastboot (blue LED), OR VOL DOWN for flashmode (green LED flashing shortly)
You probably already know these steps, but we have to make it absolutely certain that it's a hardware issue, and not an issue with the thing you do
Klaos3000 said:
How did you try to unroot? It's weird if you don't have working fastboot or flashmode, and without those, you're pretty much screwed. Those two should work even if you screw up big-time, like flashing a wrong kernel, but you must have done something weird if they stopped working?
And let me get this straight, you are pressing and HOLDING the volume buttons when you plug it to your computer, right? Make sure that the device is completely off by pressing and holding POWER + VOL UP. It'll vibrate a couple of times. Note that you're not supposed to be connected to the computer, since it'll then just boot again.
Then press and HOLD VOL UP for fastboot (blue LED), OR VOL DOWN for flashmode (green LED flashing shortly)
You probably already know these steps, but we have to make it absolutely certain that it's a hardware issue, and not an issue with the thing you do
Click to expand...
Click to collapse
I was going to flash the stock rom using flashtool right but everytime i tried to put the phone into fastboot mode it would go to the battery icon. At this point the phone was working fine. But no fastboot mode at all. Then i factory erased the phone through twrp. After that it doesnt boot up. Just sony logo no led lights. Even if i do vol up or down. Straight to the sony logo. Vol up plus power button, vibrates couple of times. I redo the process and it goes back to the sony logo.
antrax360 said:
I was going to flash the stock rom using flashtool right but everytime i tried to put the phone into fastboot mode it would go to the battery icon. At this point the phone was working fine. But no fastboot mode at all. Then i factory erased the phone through twrp. After that it doesnt boot up. Just sony logo no led lights. Even if i do vol up or down. Straight to the sony logo. Vol up plus power button, vibrates couple of times. I redo the process and it goes back to the sony logo.
Click to expand...
Click to collapse
The thing is that the screen shouldn't power on when you enter fastboot. The only thing that should go on is the blue LED. I don't use TWRP, and I don't know how it wipes stuff and if it only deletes user data, or if it formats the system. If it does the latter, then it literally wipes the system partition, making it empty, so if you ever format the system, you should flash a new ROM ASAP. A little late for that now though, but I'm still not convinced that fastboot isn't working.
ONE LAST TIME :laugh:
NOTE: The device should be disconnected from the computer.
1. Turn the device OFF by holding and pressing the POWER button and VOL UP. It should be disconnected from the computer by now. Got it? Nice.
2. Plug the USB-cable in the device first, since it's easier to plug it into the computer. Do not plug it into the computer yet. Only the Ultra.
3. Now HOLD VOL UP. Just hold it in.
4. Stick the USB cable, which is already inside your Ultra, to your computer WHILE still holding VOL UP.
5. The blue LED above the screen should light up now. The display should not power on or anything else. The blue LED is the only thing that should turn on.
Still nothing?
Klaos3000 said:
The thing is that the screen shouldn't power on when you enter fastboot. The only thing that should go on is the blue LED. I don't use TWRP, and I don't know how it wipes stuff and if it only deletes user data, or if it formats the system. If it does the latter, then it literally wipes the system partition, making it empty, so if you ever format the system, you should flash a new ROM ASAP. A little late for that now though, but I'm still not convinced that fastboot isn't working.
ONE LAST TIME :laugh:
NOTE: The device should be disconnected from the computer.
1. Turn the device OFF by holding and pressing the POWER button and VOL UP. It should be disconnected from the computer by now. Got it? Nice.
2. Plug the USB-cable in the device first, since it's easier to plug it into the computer. Do not plug it into the computer yet. Only the Ultra.
3. Now HOLD VOL UP. Just hold it in.
4. Stick the USB cable, which is already inside your Ultra, to your computer WHILE still holding VOL UP.
5. The blue LED above the screen should light up now. The display should not power on or anything else. The blue LED is the only thing that should turn on.
Still nothing?
Click to expand...
Click to collapse
I have windows 8. I remember i had a hard time trying to get it into fastboot first time i rooted and unlocked bootloader. Just dont remember what i did to get it working.
antrax360 said:
I have windows 8. I remember i had a hard time trying to get it into fastboot first time i rooted and unlocked bootloader. Just dont remember what i did to get it working.
Click to expand...
Click to collapse
Check whether the drivers have been properly installed in ur PC. If u can't get into flashmode try another system to flash the ftf. Procedure hold volume down while connecting the usb to plug. U will see a green led blink.
antrax360 said:
I have windows 8. I remember i had a hard time trying to get it into fastboot first time i rooted and unlocked bootloader. Just dont remember what i did to get it working.
Click to expand...
Click to collapse
Oh! You probably haven't installed fastboot on your computer. Download and install, and try again.
Klaos3000 said:
Oh! You probably haven't installed fastboot on your computer. Download and install, and try again.
Click to expand...
Click to collapse
Wooooohoooo phones alive jajaja. Thankssss. Though i got some more questions. First time i unlocked boatloader i was told to backup my TA files. what do i do with those now? I just flashed a stock c6806 unbranded rom. When i try to update the phone through settings it says it couldn't verify the update. i retried the process through sony companion app, and it says my phone is modded so it wont do anything.
antrax360 said:
Wooooohoooo phones alive jajaja. Thankssss. Though i got some more questions. First time i unlocked boatloader i was told to backup my TA files. what do i do with those now? I just flashed a stock c6806 unbranded rom. When i try to update the phone through settings it says it couldn't verify the update. i retried the process through sony companion app, and it says my phone is modded so it wont do anything.
Click to expand...
Click to collapse
The TA partition is where your DRM keys are. It's a good idea to backup those keys in case you want to revert to complete stock in the future, or when you need to send it in for repairs. Unlocking the bootloader will remove the keys, but since your device was - weirdly enough, already bootloader unlocked, I don't think you even had DRM keys to start with, which is again, very weird.
No biggie though. Gone is gone. The reason why PC Companion told you that it's been modified, is because you're rooted, and it knows it, so you'll have to unroot before you update. That's only if you're updating through official channels, but you have a second alternative; Flashtool. It allows you to flash stock Sony ROMs, or FTF-files.
But you're saying that you flashed a stock 6806 ROM now, and that's what? 5.0.2? Why don't you just download the .368-update (Android 5.1.1)? Then you'll be on the latest version.
Klaos3000 said:
The TA partition is where your DRM keys are. It's a good idea to backup those keys in case you want to revert to complete stock in the future, or when you need to send it in for repairs. Unlocking the bootloader will remove the keys, but since your device was - weirdly enough, already bootloader unlocked, I don't think you even had DRM keys to start with, which is again, very weird.
No biggie though. Gone is gone. The reason why PC Companion told you that it's been modified, is because you're rooted, and it knows it, so you'll have to unroot before you update. That's only if you're updating through official channels, but you have a second alternative; Flashtool. It allows you to flash stock Sony ROMs, or FTF-files.
But you're saying that you flashed a stock 6806 ROM now, and that's what? 5.0.2? Why don't you just download the .368-update (Android 5.1.1)? Then you'll be on the latest version.
Click to expand...
Click to collapse
I did unlock bootloader myself, TA file were backup. My phone is the 6806 model. The only ftf file i found on xda with a working link was for 4.2 jellybean. I just restored my TA files am going to reflash that stock rom and see what it says now.
antrax360 said:
I did unlock bootloader myself, TA file were backup. My phone is the 6806 model. The only ftf file i found on xda with a working link was for 4.2 jellybean. I just restored my TA files am going to reflash that stock rom and see what it says now.
Click to expand...
Click to collapse
Well carry on then! :laugh:
Klaos3000 said:
Well carry on then! :laugh:
Click to expand...
Click to collapse
Ill keep you posted thanks for replying though i really appreciate that.
Klaos3000 said:
Well carry on then! :laugh:
Click to expand...
Click to collapse
Phones fixed. I needed to restore my TA files in order to be fully stock. Thanks guys.
antrax360 said:
Phones fixed. I needed to restore my TA files in order to be fully stock. Thanks guys.
Click to expand...
Click to collapse
Nice!
Klaos3000 said:
Nice!
Click to expand...
Click to collapse
have my xperia z ultra same error that file will solve i dont know if my sony has unlock bootloader,