Hi all.. I try to install MM XEU in my G925F, but when i try to write with odin it says "Write operation fail".. i try to do this meanwhile is pit file (EUR-OPEN) selected, but i have the same problem..
If i connect the device on smart switch it says the device is not supported.. So i have the device locked on startin cyan screen which says in device firmware updating an error is occured.. What should i do? :crying:
ciaokefai said:
Hi all.. I try to install MM XEU in my G925F, but when i try to write with odin it says "Write operation fail".. i try to do this meanwhile is pit file (EUR-OPEN) selected, but i have the same problem..
If i connect the device on smart switch it says the device is not supported.. So i have the device locked on startin cyan screen which says in device firmware updating an error is occured.. What should i do? :crying:
Click to expand...
Click to collapse
Hello .. i have same problem ..i want to cry... i'm going mad.
Thinking about it... i don't remember WHERE , but i remember a message of someone , that wrote that BEFORE flashing , if you had "Disabler package pro" you had to re-enable all the packages.
I forget to do it.
Maybe this is the problem ? Did you also had "Disabler package pro" ?
Anyone ideas ? I cannot event enter recovery mode
---------- Post added at 06:53 PM ---------- Previous post was at 06:48 PM ----------
here's my error log:
EDIT : i come from:
Product code ITV / Android 5.1.1
PDA G925FXXU3COI9
CSC G925FITV3COI6
And tried to install:
Product code OMN / Android 6.0.1
PDA G925FXXU3DPB8
CSC G925FVFG3DPB8
This is the problem ? I can't change between rom of other CSC ,etc ?
<OSM> Please wait..
<OSM> G925FXXU3DPB8_G925FVFG3DPB8_G925FXXU3DPB8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> cm.bin
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
giansolcia said:
Hello .. i have same problem ..i want to cry... i'm going mad.
Thinking about it... i don't remember WHERE , but i remember a message of someone , that wrote that BEFORE flashing , if you had "Disabler package pro" you had to re-enable all the packages.
I forget to do it.
Maybe this is the problem ? Did you also had "Disabler package pro" ?
Anyone ideas ? I cannot event enter recovery mode
---------- Post added at 06:53 PM ---------- Previous post was at 06:48 PM ----------
here's my error log:
EDIT : i come from:
Product code ITV
PDA G925FXXU3COI9
CSC G925FITV3COI6
And tried to install:
Product code OMN
PDA G925FXXU3DPB8
CSC G925FVFG3DPB8
This is the problem ? I can't change between rom of other CSC ,etc ?
<OSM> Please wait..
<OSM> G925FXXU3DPB8_G925FVFG3DPB8_G925FXXU3DPB8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> cm.bin
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Have you flash simultane file pit and XEU? Have you try to change usb port? My problem is it
giansolcia said:
Hello .. i have same problem ..i want to cry... i'm going mad.
Thinking about it... i don't remember WHERE , but i remember a message of someone , that wrote that BEFORE flashing , if you had "Disabler package pro" you had to re-enable all the packages.
I forget to do it.
Maybe this is the problem ? Did you also had "Disabler package pro" ?
Anyone ideas ? I cannot event enter recovery mode
---------- Post added at 06:53 PM ---------- Previous post was at 06:48 PM ----------
here's my error log:
EDIT : i come from:
Product code ITV / Android 5.1.1
PDA G925FXXU3COI9
CSC G925FITV3COI6
And tried to install:
Product code OMN / Android 6.0.1
PDA G925FXXU3DPB8
CSC G925FVFG3DPB8
This is the problem ? I can't change between rom of other CSC ,etc ?
<OSM> Please wait..
<OSM> G925FXXU3DPB8_G925FVFG3DPB8_G925FXXU3DPB8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> cm.bin
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
push volume down/homebutton/and powerbutten till you are in downloadmode again. then flash pit-file and firmware....
lambik333 said:
push volume down/homebutton/and powerbutten till you are in downloadmode again. then flash pit-file and firmware....
Click to expand...
Click to collapse
never used pit-file in odin ..what is it ?
EDIT: ok i read about it.
So i need to download S6 Edge international version of pit file ? (925f is my model ) ? I see different files...
http://forum.xda-developers.com/galaxy-s6-edge/general/g925-pit-files-multi-thread-download-t3171636
Which i have to download ?
http://forum.xda-developers.com/galaxy-s6-edge/general/g925-pit-files-multi-thread-download-t3171636
Download it from this thread, the first Link (_open) and when you flash, flash the ap and this file in pit section (at right of option)
Solved
Thank you very much to all
Related
hi i'm using sprint galaxy mega(sph-l600)
but my phone is brick ...
and unable to flash with odin.
so, plz share to me sph-l600 pit file??
have a good today.
========================= modify my situation ===========================
My situation is soft brick. and do not working to flashing with odin.
always fail to flash System.img.ext4.. I've tried change usb port and usb cable. but fail..
So, I'm gonna try flash with PIT file. but I don't have SPH-L600 PIT file....
attacted my situation.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L600VPUAMK1_L600SPTAMK1_L600VPUAMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Ext4)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
raor said:
hi i'm using sprint galaxy mega(sph-l600)
but my phone is brick ...
and unable to flash with odin.
so, plz share to me sph-l600 pit file??
have a good today.
Click to expand...
Click to collapse
Hi..i don't have this model but to flash a pit file you need odin to flash it as the phone has to be in download mode also and if the phone cannot be put into this mode then flashing cannot be done, if it is a hard brick (hardware related) then the phone will require a jtag service to repair it. does the phone still come on to the mega screen?
Thank you for quick reply
starmaster10 said:
Hi..i don't have this model but to flash a pit file you need odin to flash it as the phone has to be in download mode also and if the phone cannot be put into this mode then flashing cannot be done, if it is a hard brick (hardware related) then the phone will require a jtag service to repair it. does the phone still come on to the mega screen?
Click to expand...
Click to collapse
Thank you for quick reply. but my situation is soft brick. and do not working to flashing with odin.
always fail to flash System.img.ext4.. I've tried change usb port and usb cable. but fail..
So, I'm gonna try flash with PIT file. but I don't have SPH-L600 PIT file....
attacted my situation.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L600VPUAMK1_L600SPTAMK1_L600VPUAMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Ext4)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I am trying to fix a S6 edge. The problem is that when i boot it up it shows me "an error has occurred while updating the device software"
Odin, newest version, does not see the phone. I have searched around and downloaded the G9250ZTU2COKB_G9250ZZT2COKB_BRI firmware for my SM-G9250 and trying to flash it with Odin 3.10.7
It starts but soon after starting it shows me the following error. Any help please? I have searched and found a thread where it says that i need to remove the hidden image from the file but there is no hidden image in it after extracting the tar file.
TIA
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Removed!!
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
try flashing the XEU or BTU firmware.
mikey_sk said:
try flashing the XEU or BTU firmware.
Click to expand...
Click to collapse
DON'T do this ^ - your 9250 is a different hardware variant to the 925F/I/T etc models and if you flash a non-9250 firmware you'll likely end up with a paperweight.
Anyone else with any ideas?
Will flashing a firmware with odin delete data?
Sent from my SM-G925F using Tapatalk
KingUsman said:
Will flashing a firmware with odin delete data?
Sent from my SM-G925F using Tapatalk
Click to expand...
Click to collapse
Always back up your data
Always assume flashing anything will delete your data.
If you are talking about the 6.0.1 firmware, nope it didn´t delete any of my data. Like always, search before opening a new thread.
Kirkland301 said:
Always assume flashing anything will delete your data.
Click to expand...
Click to collapse
i have problem with hidden.img on uk 6.0.1 firmware. odin says failed when I try to flash this file.
here is the log:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> cm.bin
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
EDIT: sorry, i found the solution on this thread: http://forum.xda-developers.com/galaxy-s6-edge/help/odin-fail-hidden-img-t3154903.
thanks
Hi.
My phone is Note 4, with t-mobile firmware, under battery is N910F.
I tried to root this, but phone don't want to start - no boot.
there is no my lenguage - polish
I Instaled Dr. Ketan rom, everything works perfect, but phone don't see sim card. And than root works.
its mean that root doesn't work with this firmware.
N910TUVU2DOK2_N910TTMB2DOK2_N910TUVU2DOK2_HOME - now i have this.
But no root and no polish lenguage.
I don't have any idea what to do.
Any ideas?
Sorry for my english.
I spend all night with intaling roms... And still nothing.
Hello and welcome to XDA Q&A section of the Forum.
Here is the stock ROM files for your device, flash them via Odin.
If I helped, hit "thanks"
ok, downloading now.
Tell me can I download any one of this roms?
Or only download with PL? these with PL are only with tmobile or plus operator brand...
adekm89 said:
ok, downloading now.
Tell me can I download any one of this roms?
Or only download with PL? these with PL are only with tmobile or plus operator brand...
Click to expand...
Click to collapse
You are downloading the file but asking how to download it? Also, what do you mean with PL?
RAZERZDAHACKER said:
You are downloading the file but asking how to download it? Also, what do you mean with PL?
Click to expand...
Click to collapse
I asking which one I have to download?
I know how to download and flash.
PL - Polish.
With polish language. All of this roms have polish lenguage?
adekm89 said:
I asking which one I have to download?
I know how to download and flash.
PL - Polish.
With polish language. All of this roms have polish lenguage?
Click to expand...
Click to collapse
I think all of them have it but stick to these;
Poland T-mobile
Poland Plus
RAZERZDAHACKER said:
I think all of them have it but stick to these;
Poland T-mobile
Poland Plus
Click to expand...
Click to collapse
OK, waiting for downloade end.
Maby you know where I can find custom rom for my device?
Dr. Ketan rom was fast, T-mobile rom i slooooow and there is lot of app which are usefull..
adekm89 said:
OK, waiting for downloade end.
Maby you know where I can find custom rom for my device?
Dr. Ketan rom was fast, T-mobile rom i slooooow and there is lot of app which are usefull..
Click to expand...
Click to collapse
I recommend going to the development section of your device for other ROMs.
from odin mode:
SECURE CHECK FAIL: ABORT
[1] eMMC write fail: ABOOT
from odin on PC:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910FXXS1DPG2_N910FTPL1DPD2_N910FXXU1DPD1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Rom doesnt work, it is this one which you give me. And another one dont work too
I instaled Dr Ketan, almost everything works...
I have my lenguage, sim card works.
But:
WiFi don't turn on...
Hi. I have S6 edge SM-G925F. I tried to flash custom rom,but i didn't backup EFS files. And now as you can guess, i don't have signal. I tried to flash stock firmware with odin but i got error. How can i make EFS work again? Download from somewhere and flash it? If yes,would you share it?
FakeSmile said:
Hi. I have S6 edge SM-G925F. I tried to flash custom rom,but i didn't backup EFS files. And now as you can guess, i don't have signal. I tried to flash stock firmware with odin but i got error. How can i make EFS work again? Download from somewhere and flash it? If yes,would you share it?
Click to expand...
Click to collapse
What error did you get flashing stock in odin?
I dont think anybody will share there efs backup.. as you will end up with there imei, which means cloned imei, also its illegal to do that in some countrys.
Best way is to flash the same stock you had before.
Sent from my SM-G925F using Tapatalk
callumbr1 said:
What error did you get flashing stock in odin?
I dont think anybody will share there efs backup.. as you will end up with there imei, which means cloned imei, also its illegal to do that in some countrys.
Best way is to flash the same stock you had before.
Sent from my SM-G925F using Tapatalk
Click to expand...
Click to collapse
Is this going to bring back my efs?
FakeSmile said:
Is this going to bring back my efs?
Click to expand...
Click to collapse
I did exactly the same a few weeks back. I flashed the stock i was on before and efs was restored.
Ok. Thanks a lot.
callumbr1 said:
I did exactly the same a few weeks back. I flashed the stock i was on before and efs was restored.
Click to expand...
Click to collapse
This is the error i got when trying to flash stock firmware from sammobile:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU4DPGW_G925FITV4DPH1_G925FXXU4DPGW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also how can i find out which firmware i was before i start flashing?
FakeSmile said:
Also how can i find out which firmware i was before i start flashing?
Click to expand...
Click to collapse
Which region are you? Is your phone unlocked or is it locked to a network? What android version was you on?
---------- Post added at 06:44 AM ---------- Previous post was at 06:30 AM ----------
FakeSmile said:
This is the error i got when trying to flash stock firmware from sammobile:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU4DPGW_G925FITV4DPH1_G925FXXU4DPGW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
https://mega.nz/#!rERH1LqK!QSYjirrXtPjKc1giOahnZI0BrWR2WXMg0GI3ZR3LLeY
Download the pit file from the link.
In odin click ap and insert the firmware again. The one you just used G925FXXU4DPGW.
click PIT and insert the pit file from the link. In options you need to check re partition and auto reboot.
Flash and that will fix the hidden.img
I was on android 6.0.1 August 1 st security patch. Im from Bulgaria so region should be Europe.
FakeSmile said:
I was on android 6.0.1 August 1 st security patch. Im from Bulgaria so region should be Europe.
Click to expand...
Click to collapse
Did you try to flash the firmware with the PIT?
Try this if pit didn't work ...
Extract the firmware , rename hidden.img to hidden.img.tar
Now flash hidden.img.tar in AP with Odin
BTW : it is possible you have to restart your phone in download mode after flashing the firmware to flash the hidden.img.tar after it
Good luck