How to replace a cracked Huawei Honor 7 screen - Honor 7 Q&A, Help & Troubleshooting

Mod Edit links removed

Thx for sharing, it's a helpful tutorial.:good:

Asennal said:
If the screen on your Huawei Honor 7 is cracked and it’s not under warranty, what you can do about it is either to live with it, get a new phone or take it to a professional repair store. However, either way isn’t the best. To use a phone with a cracked screen is really annoying, the cost of a new Huawei Honor 7 is too high and to get it repaired in the store costs much as well. To solve this problem, we will show you how to fix it yourself, the most economic way. Firstly, you need to buy a new Huawei Honor 7 screen online, which costs just around $45. And then, do it according to the following steps.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Before the teardown, you are several necessary tools, Heat gun or Hair dryer, Philip screwdriver, Utility knife and adhesive tape.
How to replace a cracked Huawei Honor 7 screen
Step 1
Remove the SIM card, Micro SD card and SIM card slot, put them in a box in case of missing.
Release the small screw in the slot that fixes the bezel and the rear cover.
Step 2
Use you fingernail or a card to insert into the joint of the rear cover and bezel to release the buckle and remove the rear cover.
Put the rear cover aside. Let’s look at the most important part of the phone. The screws and flex cables we labeled in the picture are the ones that need to be removed.
Step 3
Before remove other components and install the new display replacement, we need to test the new display to make sure the new display works fine. So, firstly take the old display flex cable and buckle the display flex cable of the new display. Power on the phone and test the display and touch panel.
Step 4
After making sure the new display is fine, the next step is to remove the components at the top and bottom of the phone.
Then, we need to release the mother board. Here, you need to pay much attention to the flex cable we highlighted with a red circle. There is a tiny cover, you need to use your fingernail to lift it and then take the flex cable.
Open the cover and the mother board is free to go. Now the main parts are all disassembled.
Step 5
Use the heat gun or hair dryer to heat up the edges of the screen to soften the adhesive.
Use your Fingernail or tool to remove the broken screen.
Please note that you need to remove the earpiece mesh from the broken screen and install in on the new screen.
Step 6
Remove the old adhesive on the frame and put on the new adhesive.
Now, tear off the white tape on the adhesive and put the new screen on.
Step 7
At last, put the components back in the phone and buckle all the flex cables. Before installing the rear cover, test the functions of the phone to make sure it can work properly.
Install all the components
Test the phone
Install the rear cover
Install the SIM card and Micro SD card
Congratulations! You successfully fixed your Huawei Honor 7.
Click to expand...
Click to collapse
Would the process be the same if all I need to replace is the lens/glass? Or would it be almost the same with a few steps slightly different? The actual screen and digitizer are working fine (I'm typing this message on them now). It is just the top glass layer I need to replace.

Squall88uk said:
Would the process be the same if all I need to replace is the lens/glass? Or would it be almost the same with a few steps slightly different? The actual screen and digitizer are working fine (I'm typing this message on them now). It is just the top glass layer I need to replace.
Click to expand...
Click to collapse
In my opinion, it would be almost the same, just a few slightly different. just the last replacement part different.

JerryPaul said:
In my opinion, it would be almost the same, just a few slightly different. just the last replacement part different.
Click to expand...
Click to collapse
Thanks. I decided that I can't be bothered messing around trying to do it and I can't find anywhere near me that will do it either because they can't get the needed part (even though I said I know where to get it) and don't know how to do it for this particular model. I'm just gonna use it as my excuse to finally get myself the Nexus 6P :laugh:
Sent from my PLK-L01 using XDA Labs

Related

Motorola Photon 4G Screen Take Apart Repair Guide

This written repair guide will assist you in taking apart your Motorola Photon as well as replacing damaged or broken parts on your phone. Follow each step as listed to be able to safely install new parts on your phone, such as a touch screen digitizer or other parts.
This guide will help you install the following Motorola Photon replacement part (s):
Motorola Photon 4G Touch Screen Digitizer
Motorola Photon 4G LCD Display Screen
And Other Motorla Photon 4G Parts
Tools Required:
Safe Open Pry Tool
Small Phillips Screwdriver
T5 Torx Screwdriver
T3 Torx Screwdriver
Adhesive Strips (For Touch Screen Replacements)
Hot Air Gun / Hair Dryer
Motorola Photon take apart/repair guide:
Remove back battery cover with your fingers and remove battery. If there is a memory card, remove and set aside as well.
Using the T5 screwdriver, remove all screws at the edge of the phone - there are ten total, with two hidden beneath rubber screw covers. You will need to use your nippers to remove these to access the screws.
Then you will need to use your pry tool to lift the clamp at each edge of the phone as shown in figure 1.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Figure 1​
You will now be able to use your fingers and pry tool as necessary to remove the motherboard. Use your open pry tool and your fingers as necessary and be careful as there are ribbon cables beneath the motherboard that you don’t want to rip or otherwise damage.
Use your hot air gun or hair dryer to heat up the phone and loosen the glue that holds the LCD screen and the touch screen digitizer in tact, and you can begin to use your pry tool along the seam to separate the two pieces. Figure 2 shows a demonstration of this.
Figure 2​
As the two pieces separate, the ribbon flex cable will stay connected to the front touch screen. Gently work this ribbon through the opening on the LCD screen trying not to damage the cable.
If you are replacing the screen, gently lift tape at the bottom and work the pry tool around it carefully to remove the LCD screen completely, as shown in figure 3.
Figure 3​
Now you will be able to replace any parts on your Motorola Photon. Simply replace the damaged parts with the new ones and reverse the order to put your phone back together again.
how to you put the screen back on do you need tape? will the adhesive from phone be enough for the new screen?
The adhesive strips we have on our website will be enough for your entire device.
1. Thanks!
2. Would you know of an lcd that could be substituted for the OEM part to upgrade from penile? The Photon Q lcd is the same size and resolution, but has a different connector.
My phone still working fine but the glass is cracked. Which replacement part do I need to replace?
jake.mcgee said:
My phone still working fine but the glass is cracked. Which replacement part do I need to replace?
Click to expand...
Click to collapse
You need to replace the touch screen digitizer. However, it is recommended you purchase a combination screen (touch screen and LCD) in order to complete a more efficient repair.
Replacing Rearfacing Camera
I'm in the middle of changing out my screen as well, however I was curious if there was a guide on how to replace the Rear Facing camera? I've been browsing and haven't found a guide yet. Could you perhaps point me in the direction?
Excellent Guide :good:
DIY Motorola Repairs
My company, Simple Phone Trade, specializes in Moto repairs. If anyone else breaks a Moto device send me a message if you want a link to our manuals (XDA won't let me post URLs yet) or need direction with parts and tools.
We don't sell parts or tools and are unbiased/agnostic concerning wholesalers (not to mention experienced and knowledgeable).

HTC Radar 4G Screen Take Apart Repair Guide

This detailed take apart repair guide will show you on how to disassemble your HTC Radar 4G phone quickly and safely. Repair a damaged screen or other internal parts using this step by step repair guide.
This guide will help you install the following HTC Radar 4G parts:
HTC Radar 4G Touch Screen Digitizer Replacement
Tools Required:
Safe open pry tool
Torx T5 Screwdriver
Small Phillips Screwdriver
Adhesive Strips
Hair Dryer/Heat Gun
HTC Radar 4G Screen Repair Take Apart Guide:
First, remove the lower back cover by simply apply pressure down and away from the device.
There will be four (4) Torx T5 screws that will need to be removed, as shown in Figure 1.
Gently pry the inner back cover from the device using a safe open pry tool.
With the inner back cover removed, you will now have access to two (2) more torx screws and one (1) flex cable. Release the back side of the jaw clip and remove the small flex cable.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Figure 1​
The back housing can now be gently pried away from the rest of the device. Use a safe open pry tool to assist with this process.
With the back cover removed, you can now remove the battery.
Remove the five (5) T5 screws as shown in Figure 2. Remove the lower bar that the two lower screws were holding in place. The top cover can also be released using a safe open pry tool.
Release the two (2) wire connections on the motherboard and the two (2) pop connectors from the motherboard flex cable. The button flex will also have to be released from the housing as shown in Figure 2.
Figure 2​
The motherboard can now be gently folded down and the last jaw connector can be released. The motherboard can now be removed.
The upper board will also need to be removed. It will be lightly clipped into place.
The screen assembly now needs to be separated.
You can now heat the front of the touch screen using a heat gun or hair dryer on medium hate. Use quick movements around the outside edges for about 45-60 seconds. Now, using a safe open pry tool, pry between the front housing and touch screen to release the adhesive holding it in place. Reheat the touch screen if necessary.
The touch screen flex cable will need to be fed through the housing, so be careful of damaging this when separating the screens. The LCD screen will just need to be pried out using a safe open pry tool.
Simply replace the damaged parts with the new ones and reverse the order to put your phone back together again.
Here is how it looks practically
http://www.youtube.com/watch?v=Qs_kfqCbuxY
this guide also counts for the standard HTC Radar right?
EaterOfCorpses said:
this guide also counts for the standard HTC Radar right?
Click to expand...
Click to collapse
Yes. Its for the Radar.
Does radar have some standard HTC battery? I need to replace battery and need to know exact type.
Thanks!
Help!
So, trying to help out a neighbor friend and I took apart the phone without ANY problem. I couldn't get the original LCD screen to light up again (figured I broke it prying it out) so I bought a new one on ebay. Now, that one won't work. Note: I notice there are a lot of contacts on the phone, and I'm testing it prior to putting all the screws back in and everything. Any idea what may be wrong. I know it didn't 'break' anything (other than possibly the LCD) taking it apart - it was quite easy. Let me know if anyone has a though of something I may be missing or what else I should attempt.! ...and soon!
Thanks
Mnorto3
Do you carry the LCD Screen replacement for this model?
jake.mcgee said:
Do you carry the LCD Screen replacement for this model?
Click to expand...
Click to collapse
Yes we do. A link to our site can be found in our signature below.

How To Repair HTC Titan Screen

Does the outer glass touchscreen of your HTC Titan has been damaged or cracked? Need to replace the digitizer and other internal parts of your smartphone? This written repair guide for HTC Titan will show you in a step by step manner on how to quickly and safely disassemble your device and replace the common damaged part.
This guide will help you to install the following HTC Titan part(s):
HTC Titan Touch Screen Digitizer Replacement
Tools Required:
Safe Orpen Pry Tool
Torx T6 Screwdriver
Adhesive Strips (for touch screen repair)
Hot Air Gun / Hair Dryer
HTC Titan Repair Guide:
Start by removing the back battery cover, battery, and sim card.
Once the back cover removed, we can now remove the eight (8) Torx T6 screws located in figure 1.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Figure 1​
There will now be three (3) latches along the top and sides that need to be released. Use a safe open pry tool to lightly press these clips and remove the back housing from the rest of the device.
Once the motherboard has been exposed, there will be two (2) screws that need to be released, one at the top motherboard and one on the lower, shown in red on figure 2.
Figure 2​
You can now lightly lift the vibrate motor from the plastic socket, leaving it connected by the wire cable (yellow).
The power button and volume button will have two small flex cables placed underneath the physical buttons. Use a safe open pry tool to softly lift these cables away from the housing. Be cautious, as these are held in place with adhesive. (Shown in green in figure 1)
Two (2) jaw connections will need to be released, one for the touch screen and one for the LCD screen. Lightly lift the back of the jaw connector and remove the flex cable located inside. (Orange)
Use a safe open pry tool to start lifting the motherboard from the device. Be cautious, as there are clips holding the motherboard in place. Release these clips and lift the upper and lower motherboard up. Note that the antenna cable will need to be wiggled loose from the cable fasteners.
Remove the motherboard totally. Use a heat gun or hair dryer to begin warming the front of the screen assembly. Work around the outside edges of the screen on medium heat for about 45 seconds. This will soften the adhesive holding the screen assembly to the housing.
Once the screen is properly heated you can use a safe open pry tool to being lifting the screen assembly away from the housing. Be sure to lift both screens out at the same time.
After the screens are partially released, be sure the flex cables are fed through the housing. Remove the screen assembly.
Use the heat gun or hair dryer again to warm the seal between the touch screen and LCD screen. Use speedy movements for about 30 seconds. Once this is complete, use a safe open pry tool to carefully separate the screens.
You can now replace the touch screen digitizer or LCD screen.
Reverse the instructions above to reassemble your phone.
have you actually done this on a Titan? I thought I read that the digitizer and lcd were bonded together with a resin and could not be seperated.
i can tell u there is no way to do it like u say...
digitizer and lcd are glued together...
but of course maybe iam wrong so please show us a video how to do...
Sent from my TITAN X310e using Board Express
do you have a fused screen assembly for this model?
jake.mcgee said:
do you have a fused screen assembly for this model?
Click to expand...
Click to collapse
no actually we just carry the Touch Screen Digitizer
miahshodan said:
have you actually done this on a Titan? I thought I read that the digitizer and lcd were bonded together with a resin and could not be seperated.
Click to expand...
Click to collapse
On this device the LCD and digitizer can in fact be separated.

DIY - How to replace cracked prime Screen? (Not solved yet)

The intention of this thread is to come up with do it yourself steps to replace a cracked prime screen. Replacement screens are easily available on ebay and cost about $100 USD.
Also the replacing should not be so tricky (once we know how) because there is no soldering or heat gun involved.
There have been a lot of teardown of prime's, but unfortunately none of them contain information on how to take out the glass + digitizer successfully.
I think here is how the prime screen is layered. In the front is the Gorilla glass. The second layer is the digitizer which is glued to the glass. The last layer is the LCD screen.
Here is an image of LCD panel of prime (Image from Anandtech teardown)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Here is an image of how a replacement screen looks like
I have been able to perform the following steps so far..
1) Open prime (easy)
2) Unscrew 4 screws that hold the LED panel (easy)
3) Take off a few tapes (esp the yellow tape that holds the digitizer ribbon.
Steps I could not complete so far (hence speculating)
4) Pull off the LCD panel
5) Take off the two ends of the digitizer ribbon from the motherboard on the other half of prime. (unlatch the connector, and pull ribbon gently)
(at this point the Screen + Digitizer should be completely seperate from the rest of the body)
6) Take off the WIFI & WIFI + GPS plates from the top of the frame
7) Take the replacement screen, and put in the WIFI & WIFI + GPS plates
8) Place the LCD panel on the new replacement screen. Tape and screw in all 4 screws.
9) Connect both ends of the connector ribbon from digitizer to the motherboard
10) Make sure nothing is loose.
11) Attach both halves of the prime again
12) Turn on the tablet, and if screen comes on and you can interact with touch screen then we are done!
Sounds easy... it should have been easy too... just that I have not been able to figure out how to easily complete step 4 above.
Has anyone else been able to get past this step?
I will update this thread with any feedback provided and will mention your name in credits as well for sure.
Hopefully, once we can solve this, it should be much cheaper to fix cracked screens compared to RMA or third-party fixes.
EDIT : August 2nd
Thanks to 'Two Dogs', he found a recent thread where someone successfully replaced his prime screen. You need to have a shattered screen (like mine ) for his steps to work.
Look at the third last post on this thread
http://forums.whirlpool.net.au/forum-replies.cfm?t=1857530&p=71
The user has put in a lot of images as well.
So it's very doable!
really like the idea of this thread and what your doing here. I havent needed to take apart my prime yet and hopefully wont ever need to. good luck!
Yeah I agree. I've had this thing for a month and a half, and the screen already has 2 scratches and a rub mark that goes across the entire screen where (I guess) it rubs along the lower edge of the keyboard. The ridge between the keyboard and the trackpad. I'd love to be ble to replace it when it gets unbearable.
You need suction cup an heat gun or hair dryer an you must slowly heat all four corners and then you can remove old digitizer or cracked pieces of it. Its tricky but put it all back together is hard, because digitizer glass is so thin and fragile. Do not push it hard or it will crack.
I saw a movie on youtube for the original Transformer TF101.
I assume this is very similar.
For the TF101, the digitizer/glass was adhered to the lcd panel with 2-sided tape. He used an exacto knife and just inserted it between the two layers and went around the entire perimeter of the screen (think he had a heated one, but said a regular would work too. The heated one just slid through the tape better).
He made a mark on the blade of the knife so he would not insert it too far to risk damaging the ribbon cable (though your new screen should have the cables on them, so probably doesn't matter if you damage the old ones). Using the new replacement screen as a template, you should be able to mark your blade to get deep enough without getting too deep to risk damaging any components.
Here is a link to the video. http://www.youtube.com/watch?v=brcZLrocBio
Start about 2 minutes into the video to see how he got the glass off (the first 2 minutes discuss dis-assembly, which you have already done).
ccrobin said:
I saw a movie on youtube for the original Transformer TF101.
I assume this is very similar.
For the TF101, the digitizer/glass was adhered to the lcd panel with 2-sided tape. He used an exacto knife and just inserted it between the two layers and went around the entire perimeter of the screen (think he had a heated one, but said a regular would work too. The heated one just slid through the tape better).
He made a mark on the blade of the knife so he would not insert it too far to risk damaging the ribbon cable (though your new screen should have the cables on them, so probably doesn't matter if you damage the old ones). Using the new replacement screen as a template, you should be able to mark your blade to get deep enough without getting too deep to risk damaging any components.
Here is a link to the video. http://www.youtube.com/watch?v=brcZLrocBio
Start about 2 minutes into the video to see how he got the glass off (the first 2 minutes discuss dis-assembly, which you have already done).
Click to expand...
Click to collapse
will open my prime again to test this theory over the weekend. Wish there was a youtube video though for 201.
Sent from my Transformer Prime TF201 using Tapatalk
I'm interested in this, how do you open the prime to begin with?
I think i'll just buy a total screen replacement, about AU$120 on ebay, and just plonk the new one in, but I want to find out if i can easily open up the prime before i buy.
e: oh wait, that $120 product is simply the glass + digitizer. where do i go to find it for $70??
ee: nvm, i replaced 'prime' in my ebay search with tf201 and it found the cheaper one!

One screen issue, trying to fix...

hey guys
well about 7 days ago, after leaving my htc on charge i came back to a buggy lock screen(digitizer) issue! screen seemed like it didn't want to respond
was gutted, after work i decided to twrp recover my system, change kernel etc still didnt work :/ then downloaded a drawing app. to find that a vertical middle section of the screen wasn't responding as my phone is now out of warranty! it was either to ebay to sell it as faulty or to ebay to source parts lol. so i started hunting around and found this can be a common problem, the ribbon cable for the digitzer(which is located near the head phone port on the pcb can come loose! so next step meant only one thing DISASSEMBLE (gulp)
found this handy tutorial on you tube https://www.youtube.com/watch?v=90og2HFQUHU (sorry if its been linked before)
so with a window sucker and a guitar pick i slowing persuaded the back off the device(its fiddly but not too much of a nightmare!
i located all the screws and after fighting the copper heat shielding its now in parts
my issues now though, which if anyone can guide me would be awesome
firstly, i am in the uk(european model) i am unsure what screen i need, is it s sharp or a sony?
secondly there are 2 antenna adhesive tabs located on the reverse on the screen housing, one i assume is for wifi, other is gsm etc
the antenna tab is near the capacitive buttons, this is slightly damaged! my question, it looks like it has antenna tracks(can i replace with an adhesive without tracks?
i have add some picture(sorry if my terminology is wrong guy)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
hey guys, quick update i ordered the SHARP lcd last night, will attempt to repair it in the next few days
ebay link below(frame and LCD) UK seller: seems a reasonable price at £31.30, worth the gamble i think
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=291107539349&ssPageName=ADME:LC:GB:3160
anyone have any advice about the antenna adhesive issue?
hey guys, quick update screen turned up this morning, will attempt to fit tonight(excited and apprehensive to).
anyway i have purchased some adhesive conductive tape to repair the antenna areas(picture above with arrows). i believe the tape is thin enough to fit correctly, will cut down to match the size needed for gsm antenna and wifi antenna. but it will need folding correctly to allow the ribbons cable to contact correctly.....
i have also purchased some double sided tape to allow me to secure the battery and rear housing. also may use it to hold the volume rocker and power button in place on the chassis
so its fingers and toes crossed lol and a hair dyer at the ready lol
will keep you all updated
new screen fitted all seems good antennas signal is good phew
took about 2 hours all in all....
few tips beware of the power button it will only fit one way!
masking tap to hold the volume rocker and power in place defiantly will make your life easier
few things to note, the ribbon cable connectors on the logic board(s) are very very fiddly to position and lock into place! just take a few minutes on each(make sure its aligned to)
the hot key buttons need to be exactly lined up, there are two dots/guides on the frame(easy to miss), keep all contracts clean from finger grease to.....
i also checked all the contact springing(not sure if that's there tech name lol) i positioned them so they would contact correctly on the back cover when refitted(these are for wifi/gps/nfc). then moving onto removing any old adhesive from the battery and back cover(make note of where the adhesive is along with size, space is tight, fitting new adhesive over old would be too crammed. only fit new adhesive where the old was located now the two halves of the phone need to be fitted back together, this was very straight forward and it clicked into place without any issues then using a hair dyer to get the unit warm, just to allow the adhesive to mold inside
(******have to admit i didn't pre-test the screen, bit of a newbie error******) lucky for me it powered on, no dead pixels
i have ran the following sequence: *#*#3424#*#* in the phones dial-er to test everything(from the screen/WiFi/blue-tooth/sensors etc) just so i could check that its been rebuilt correctly after this i installed CPU z and stability test v2.7(which stresses CPU and GPU under-load) i did this to test temperatures! unit ran for 30 minutes very warm, no problems, allowed it to cool to the touch.
phone looks like new and is currently running perfect i will update this thread if i find any issues
but for anyone wanting to try a screen/digitizer repair its defiantly worth the time and the gamble

Categories

Resources