i bricked my acer b1 a71 trying to install twrp. after flashing it successfully and went to reboot . it just showed ther acer logo then blank screen. i tried going to recovery but was just able to go to the first part where you have three choices sd image update mode flashboot mode and clean boot. i tried all three and just acer logo then blank screen. tried the reset pin on the side but still nothing. i read and study all tutorials there is and it all boils down to having a stock rom. now i"ve searched and searched the entire net and i was able to get two stock roms but i dont know if it is okay or not because when i use the scatter file on sp flash tools it says scatter file error or format error i tried to rename it but till error. i used every version of sp flash tools and still scatter file error. so i dont know if those roms are legit or not. also my laptop is 64 bit. i read somewhere that mtk6577 is not supported by 64 bit. the mtk on the specs of acer is mtk8317t but it is also recognized as mtk6577 and that is also what mtk droid tools showed. can anybody please help me here. i know xda has helped a lot of peole and im hoping that i can be also one of them. thanks a lot in advance.
Related
Alright, I own a TCT Alcatel One Touch 918/Alcatel OT-918/T-Mobile Move 2 android device. Now, I have rooted it before, after a while it went into the startup loop, I sent it to repair, and now apparently they upgraded software and it's working fine, however when I try to use scatter.txt and recovery.img that I used before to root it with FlashTool, I get an error "Can not find USB port...", now, I am trying to find a specific scatter for my phone, I have all the drivers installed, although when I tried to install with alternative methods I get "Device tree not found" error, anyway, I need a scatter file, so could someone provide me with ways of getting them for a certain device, please?
Thanks!
Hi, I was trying to use Flash tool and Don't know what happend but My Phone is completely DEAD right now even power button is also not working no screen is there (just blank phone).
I am having UMI X2 2GB rom, 32 gb internal memory, 1.5 GHZ (MT6589T) Model.
I tried to use SP Flash tool to recover my phone. Firstly I tried to format the phone, After that I tried to run the correct scatter file for MT6589 (from one of the ROM Posted under UMI-X2).
Drivers for the SP Flash tool is loaded correctly (into my Windows 8 Pc). I was previosly getting error as follow : SP FLASH TOOL ERROR: (8200)
[Platform Error] The load and target are inconsistent!
Now, after searching a lot I found that its something wrong with SP Flash tool version.
So I downloaded SP Flash Tool V3.1304.O.sn119 version. After that I am trying to "Download" the rom (with the correct scatter file for my ROM). but its only showing me RED Bar (with 100%) and after that it does nothing. Its neither showing me any error nor its continuing the process.
I am in serious problem here. Please help me out.
Thanks in advance!
- Umang
umang_nine said:
Now, after searching a lot I found that its something wrong with SP Flash tool version.
So I downloaded SP Flash Tool V3.1304.O.sn119 version. After that I am trying to "Download" the rom (with the correct scatter file for my ROM). but its only showing me RED Bar (with 100%) and after that it does nothing. Its neither showing me any error nor its continuing the process.
I am in serious problem here. Please help me out.
Click to expand...
Click to collapse
Try this version of :
SP Flash Tool
October Official Rom
USB Drivers (if needed)
Works for me.
Necro thread...
I have the same issue.
A couple of days ago the phone just started turning off / locking up when off, and having great difficulty tuning on... i.e. pulling out the battery for a minute or a few times.
Now the phone won't turn on at all. They only sign of life is the charging animation when you plug it in.
Prior to all this, there appeared a window in Chinese with some options. my GF (who's phone it is) just pressed something, no idea what. But she said something about 'drawing on the screen'??? sound like something locked up and the previous frame wasn't deleted from the frame buffer before redrawing the new one... I have no idea.
Anyway, I tried going into recovery to see if there was anything I could do there, unfortunately everything was in Chinese, so not much help. for some reason now, the recovery isn't even working.
Now I can connect to the phone via SPflash, but I get the above response: '[Platform Error] The load and target are inconsistent!'
Some other ROMs I tried give me this response:
'The load to be downloaded is for MT6589;
The target platform is MT6582_S00'
Which is quite suspicious.
Any ideas?
Thanks
hisense HS-U980 bricked....
hi,i have the smartphone hisense hs-u980 with mt6589 or mt6589t, i dont understand.... so, i briched with sp.flash tool and now is ompletly dead,,, can i have ur help-sipport please?
thank u very much
Hs-u980 complete dead/bricked
carretto76 said:
hi,i have the smartphone hisense hs-u980 with mt6589 or mt6589t, i dont understand.... so, i briched with sp.flash tool and now is ompletly dead,,, can i have ur help-sipport please?
thank u very much
Click to expand...
Click to collapse
i have ur same phone and i have ur same problem,my pkone is dead later flash any wrong miui rom from cwm recovery and now is dead,i dont have any idea where is original firmware for sp.flash tool or other how piranha box,please,anyone can please me??? THANK U for read!!!!
I have the same Problem. So frustrating men. If anyone finds a solucion please email me [email protected] ...
SP FLASH TOOL ERROR: (8200)
As i connect my phone it disconnects after 2 seconds..
Please give me a site to download scatter file for my micromax a 310
At first guys, excuse me if the topic isnt at right place but i cant find the right section.
So i have a Prestigio Multipad 8.0 HD (PMP5588C).I think i have bricked it.I erased NAND with Amlogic Image Burning Tool and now the device wont boot.The screen is black even when im charging it.I wont boot at all.I tried to boot in recovery but no succsess.Ive tried to boot it normally and in recovery (even when i charged it 10 hours usually it charges for 4 hours) but the screen is black.When i connect it with Power and Vol- buttons it shows up in the device manager as M6-CHIP and ive installed the drivers so now is World Cup Device.Ive tried to use Amlogic Image Burning Tool again but it fails on load spl.Any ideas?
Thanks in advance!
Best regards, Stoio.
Im sorry for my English but im from Bulgaria.
Unbrick amlogic tablets
Hello stoio
I have almost the same Tablet. It's a Prestigio PMP5580C, for me it is labeld as Intenso Tab 814, but they are completely the same. I have tried to find the u-boot.bin in the stock firmware, but I didn't sucess yet. I've downloaded several tools which allows me to make my 16 GB MicroSD card recognized as a 512 MB SD card, there I have to put the files on it to unbrick my tablet, it's amlogic (like my username) (someone told me that this is the chipset). It has a TOSHIBA TC58TEG6DCJTA00 NAND flash chip of 8 GB capazity. I also need help by getting my tablet unbricked.
In the future Inwant to learn with this amlogic based tablet how to create custom ROM's, recoveries and custom boot splash screens.
Thanks for any help, I reall appreciate your help,
Please note that I'm from Germany and my English is not good as it should used to be, but I have a dictionary (as a normal book) where I can get good communication with you. I like the idea of using english only.
Every Image (.img) were made with the dd command, I need to look inside in the images and open the content, I used a hex editor and tried to strip off the 2k of data, but I can't success. I'm using this tutorial:
I'm using this hex editor under linux: Okteta
I don't know how to delete the 2k of data. I need to know what content the partitions have to unbrick my amlogic based tablet, cause I'm seeing still the white android robot, and the charging battery or charged plugin picture, but this tablet doesn't have a bootloader or recovery so I'm out of ideas, the only way for me is to use a microsd card like an live cd to automatically let this tablet flash stock firmware, but where is it? Please help me out, I meight be wrong, it's possible that different repairing ways exist, too.
Hello
I bought a Lenovo p780 from a Chinese website 6 months ago (4gb), rooted.
I faced a problem with the signal of sim cards "invalid imei", so I tried to install TWRP recovery using a tutorial I saw online to use the recovery to install a new "modem" file. I used Mobileuncle app to do this but this step caused my phone to enter a bootloop, and the only way to get rid of this loop is to press the reset button whenever you want to turn the phone on! I tried to install other recoveries using Mobileuncle but nothing has changed too!
I also tried to flash a stock rom using sp flashtool but it just didn't work!! I tried many stock roms versions and many versions of the flash tool programs but when I press "firmware upgrade" or "download" nothing happens! believe me I tried everything to make this happen, I even tried to do this on different computers (win 7 and win 8.1) but I got the same result: nothing! No need to mention that I've already installed all the USB drivers on my computers. I read every single word in every single tutorial I found (including tutorials from this forum), but it's always the same failure!
I tried to change the modem file using Root Explorer but I missed with some folders and now even the Wifi doesn't work. All I need now is get my phone functions as normal with stock rom or with a custom rom.
I would be very appreciated if you can tell my what's wrong and why I can't flash a rom to my phone although it's not bricked at all and I can turn it on!
Hi everyone,
I managed to brick my Cube T8 Plus trying to root it. Now it is no longer recognised by Windows, does not turn on does not get into recovery. Any hope?
So desperate for some help here...:crying:
This is my problem too. I even can not find rom for it . i got it last week and i am sure it was 20160225 virsion.
Same problem here.
Recovery is working but it is not recognized by the pc (windows 10).
I tried to transfer a file by using a SD card but it does not appear on the recovery (install zip metod).
Try the SP flash tool.
its seems to be crashing on my PC.
any suggestions ?
You can download the file T8-PLUS_V1.0_20160218. use google to find and download it.
it contains the SP flash tool and a list.
tell me if you succeeded.
i didnt
Also same problem
I think I made a misstake and formated my whole Cube T8plus.
So I wonder if someone have a backup to share that I can try to use for recovery?