Related
Hi,
Last week i got my Galaxy S2 and am really obsessed with the performance and beauty of her.
Today i installed lastest version of Kies and when i connected my phone thru USB, it said that new version of firmware is available (KF3).
I clicked OK to upgrade the firmware and it showed downloading firmware and after some time it said that "Failed to convert to upgrade mode" and i tried upgrading my firmware for 5-6 times but no luck..
Any one here know how to update the firmware to KF3 (INDIAN version)
Turn OFF AV and Firewall .
jje
thanks mate...but i tried but no luck....
Try resetting your phone to factory settings.Sometimes there are certain apps which interrupt the upgrade procedure. Needless to say, Do backup all your data and apps
better you would use odin to flash a rom.
Make sure you installed KIES in administrator mode.
Somehow i followed the steps given by you guys and able to successfully download the firmware. but after some time Kies showed some error in unknown language ( i think its korean) with only OK button (dont have a screen shot though).....now my phone was showing a little android guy with "Downloading....do not turn off target".....i waited for nearly 1.5 hrs and nothing happend...then i searched in net, there it asked me to power off the phone and switchng it on again.....
it came back online as usual and when i cheked the version it was still showing my old one.....any idea what went wrong? and what the heck is that error message, written like a chopstick house......
Solved
i had faced similar isssues while trying to upgrade for last 2 days.
it worked today - all i did was start Kies in Administrator mode.
kies didnt download the firmware again - it took it from previous downloads and did the upgrade.
try it out!
rb69 said:
Solved
i had faced similar isssues while trying to upgrade for last 2 days.
it worked today - all i did was start Kies in Administrator mode.
kies didnt download the firmware again - it took it from previous downloads and did the upgrade.
try it out!
Click to expand...
Click to collapse
I have been trying to download the new firmware since last 3 days, I even reset the phone back to factory setting, also using Kies in Administrator mode but everytime I click on the option of firmware upgrade it does the back up but after that it says "connection to Gt-i9100 lost ".
Any idea why this would be happening ?
Also any noticeable difference after the update ?
abhi021 said:
I have been trying to download the new firmware since last 3 days, I even reset the phone back to factory setting, also using Kies in Administrator mode but everytime I click on the option of firmware upgrade it does the back up but after that it says "connection to Gt-i9100 lost ".
Any idea why this would be happening ?
Also any noticeable difference after the update ?
Click to expand...
Click to collapse
Any solution on this ?
abhi021 said:
I have been trying to download the new firmware since last 3 days, I even reset the phone back to factory setting, also using Kies in Administrator mode but everytime I click on the option of firmware upgrade it does the back up but after that it says "connection to Gt-i9100 lost ".
Any idea why this would be happening ?
Also any noticeable difference after the update ?
Click to expand...
Click to collapse
earlier i did the factory reset (including USB erase) plus re installed USB drivers from Kies menu few times at home but it was not upgrading.
Just reconnected on a different machine (as was trying sitting at work ) it just worked. Yesterday I did face teh same issue at work machine as well.
most likely it looks to me either a USB driver issue and / or admin issues.
Hope it helps.
yet to come across any significant improvement changes. still in the mode of re installation of apps.
I tried everything...did factory reset, ran kies in admin mode etc....but still no luck.....can i use odin to update my firmware? if i update now using odin, can i update the next release of updated firmware with kies?
rb69 said:
Solved
i had faced similar isssues while trying to upgrade for last 2 days.
it worked today - all i did was start Kies in Administrator mode.
kies didnt download the firmware again - it took it from previous downloads and did the upgrade.
try it out!
Click to expand...
Click to collapse
i had the same thing happening to me!
when i updated from ke1 to ke7 , and when i updated from ke7 to kf3>
i hate kies
People seem to regularly have problems with Kies. My biggest one is getting the firmware to download: it often times out more than half-way through, eating up big chunks of my broadband data cap every time.
Odin is usually the most reliable way of doing a firmware update. Make sure you use the USB cable that came with the phone, because people have had problems using other cables (such as ones that come with HTC phones).
If you do a firmware update through Odin, it doesn't necessarily prevent later updates through Kies. The only thing you need to watch is that you're using a Kies-released firmware that's correct for your phone. For example, if you've got an Indian phone (GT-I9100LKAINU), you need to flash the XWKF3/ODDKF3/DDKE4 firmware. This is the latest Kies release for that phone. If you flashed a different firmware, such as the XWKF3/XEUKD1/XXKE7 firmware for European phones, Kies will no longer find updates.
You can use the Check Fus Downloader (v1.2 at fus.nanzen.se) to find the latest firmware for your phone, and to download an Odin-flashable package. This will give you a ZIP file, and inside that is a TAR file. This TAR file is then used by Odin.
SOLVED : [Q] SGS2 - Firmware Upgrade - Failed to Convert to upgrade mode
SOLVED...
used odin and downloaded the latest firmware zip from http://forum.xda-developers.com/showthread.php?t=1075278 ...took only 3 mins to do this work.....
thanks to all for helping me in this....
which firmware did you download~ seems there are lot dif version a/c to country. so not quite sure which one for me..help?
Hi altogether,
i have an SGS2 and got an ofer to upgrade firmware via kies. I didnt flash or root anything with this phone yet.
After flashing the phone via kies i only get the problem picture: Phone-yellowtriangle-PC. AFAIK this is the sign you get, when the bootladers are corrupted. Am i right?
NEvertheless download mode is accessable, so i downloaded a stock firmware from this site and tried to flash it via odin. It connects, starts to flash, but wont go further than SBL1 for over 10 minutes. then i stopped flashing. I tried the same with just the kernel and it flashed correctly, and the phone restarts, but just to the SGS2-screen with a yellow triangle at the bottom. No further for over 30 minutes, so i canceled that too...
Any suggestions, how i can rescue the phone? Data is not important, i just want to get it running again...
try to use the files from the next thread:
http://forum.xda-developers.com/showthread.php?t=1075278
edit:
in addition try to preform a full wipe if the data is not important (will delete all data including the contacts)
Also make sure NO Kies related processes are running (Taskmanager -> "End Process" everything that even remotely sounds like anything containing "Kies").
Connect phone to another USB port and do not use a USB hub, connect the phone directely to the PC.
Maybe that helps a bit....
Thank you for your fast answer, but that is the guide i used first to flash a stock firmware. I maybe should have mentioned it. And thats the way it didnt work.
Just the single kernel worked out to cause a little positive result. But only seeing the start screen (not even bootlogo, and no further) is not what a phone should do.
genius5 said:
Hi altogether,
i have an SGS2 and got an ofer to upgrade firmware via kies. I didnt flash or root anything with this phone yet.
After flashing the phone via kies i only get the problem picture: Phone-yellowtriangle-PC. AFAIK this is the sign you get, when the bootladers are corrupted. Am i right?
NEvertheless download mode is accessable, so i downloaded a stock firmware from this site and tried to flash it via odin. It connects, starts to flash, but wont go further than SBL1 for over 10 minutes. then i stopped flashing. I tried the same with just the kernel and it flashed correctly, and the phone restarts, but just to the SGS2-screen with a yellow triangle at the bottom. No further for over 30 minutes, so i canceled that too...
Any suggestions, how i can rescue the phone? Data is not important, i just want to get it running again...
Click to expand...
Click to collapse
Don't use kies, its rubbish, when this is fixed just use ODIN Use the method in intratechs thread in the dev forum, using Odin
Sent from my Samsung Galactic Crusader S II
Hope someone can help. Recovery is accessable too?
As it was Kies i would take to a service centre .
jje
Great MAster Darkyy helped me, and gave me that advice too. I dont really understand, what exactly went wrong, but as no flashing worked....
i just build myself a JIG, reseted the counter and will send it to service now....
nevertheless TY for all your help and fast answers....
How can a global player like Samsung really keep crappy software like KIES on the market for such a long time??? Did it ever work???
genius5 said:
How can a global player like Samsung really keep crappy software like KIES on the market for such a long time??? Did it ever work???
Click to expand...
Click to collapse
No complaints to Samsung is probably why .
jje
Scenario; You installed a custom recovery and rooted your Mega. Now you want to try and flash a custom rom, you make a mistake and flash a incompatible rom. Now your Mega won't turn on properly, Odin won't recognize it thus leaving you unable to flash a stock rom. I'm here to try and help, or atleast explain what I did to fix my own problem.
First: Unless you haven't already download the drivers for your Mega and then visit the Samsung Kies Website and download the Kies software, the first one, not Kies 3.
Third: Click the tab Tools > Firmware Upgrade and Initialization. A pop up window will appear and ask for your device model. Type in CAPITALS, so for example mine was SGH-I527M. Click OK, next time your S/N or Serial Number. This can be found under the battery on the back of the phone. Click OK.
Continue through the prompts and agree to terms until it asks you to connect your phone.
Fourth: With the USB cable NOT connected enter download mode, do so by holding Home+Power+VolDown at the same time. Then press volume Up to enter download mode. Click Upgrade on Kies and wait for the process to finish.
Mine took about 40 minutes but worked like a charm. I hope this helped at least one person, if not, it will be a good referance.
tq bro,help alot.
Yes i an trying your suggestion. Thanks. I will give you feedback after successful.
I have tried this as suggested but after it completes it keeps rebooting same as b4.
After 3 days. I did talk you that if it works good then i will give you good feedback or i will give you something. SO i saw that after using suggestion it's not works properly rebooted another. Just time expand. can you post here video tutorial about this. I think we are doing another mistake. So if you post here tutorial then it will be easy for me..
S6 edge stuck on opening logo of "Samsung galaxy S6 edge" - it's not mine, so I can't know the history that caused it - but I think it's related to a bad try of rooting.
when trying to flash a new stock firmware from Sammobile getting the same problem - even after wipe and wipe cache.
on recovery getting this messege on the bottom:
dm-verity vertification failed... need to check DRK first...
this is what I tried to do to fix it:
1) flashed newest stock - still no do.
2) tried to flash with smart switch - it did flash - but it didn't help - phone still in bootloop.
3) flashed S6-UniKernel_v6-0001-ODIN or S6-UniBase_BOG8_v2 - it did helped, the phone worked, but I lost the IMEI and needed a certificate to fix the IMEI, I did it and the phone works fine..... BUT I can't left it with a custom rom 'cause I want the original updates and the original stock rom.
4) tried to flash the repair firmware G925FXXU1AOCV (comes with 4 files CSC, AP, MODEM and BOOTLOADER) which is 5.0.1, so it fails (tried also with pit file) - didn't do.
5) last thing I'm willing to try - is to split a new firmware to CSC MODEM BOOTLOADER and AP by myself... the only problem is - I don't actually know how to do it.
another thing I've noticed on the download mode it is written:
Current Binary: samsung Official and System status: custom
I was wonder if someone can give me a clue what to do, and how to fix this problem.
thanks!
What country are you from? Are you sure the phone isn't on 5.1.1??
Download the firmware from sammobile of your own country or the nearest country/countries, put the device in Odin mode and try to flash that one through Odin "AP" Okay "IF IT FAILS" (copy the Odin log and paste it on this thread. If it succeeds LET US KNOW PLEASE.
Be sure of the Android version.. If that's impossible my safe bet is to flash it with a rom for 5.1.1
You shouldn't mess with the PIT files!
curiouswrecker said:
What country are you from? Are you sure the phone isn't on 5.1.1??
Download the firmware from sammobile of your own country or the nearest country/countries, put the device in Odin mode and try to flash that one through Odin "AP" Okay "IF IT FAILS" (copy the Odin log and paste it on this thread. If it succeeds LET US KNOW PLEASE.
Be sure of the Android version.. If that's impossible my safe bet is to flash it with a rom for 5.1.1
You shouldn't mess with the PIT files!
Click to expand...
Click to collapse
hey,
first of all, thanks for the replay!
If I flashed with smartswitch - then it should flash the newest rom and the one who fits for the device.
what I flashed in odin is: G925FXXU3COJ1_G925FOJK3COJ3_G925FXXU3COJ6_HOME.tar
which is Israeli firmware and 5.1.1
Entebox said:
hey,
first of all, thanks for the replay!
If I flashed with smartswitch - then it should flash the newest rom and the one who fits for the device.
what I flashed in odin is: G925FXXU3COJ1_G925FOJK3COJ3_G925FXXU3COJ6_HOME.tar
which is Israeli firmware and 5.1.1
Click to expand...
Click to collapse
Okay, BUT when you ran Odin did it succeed or fail flashing the device?
If it failed what was displayed on Odin logs?
If it failed, Please re-flash your device again through Odin and whether it fails OR succeeds, COPY THE LOG AND PASTE IT HERE !
I need to see the logs, if you want help.
curiouswrecker said:
Okay, BUT when you ran Odin did it succeed or fail flashing the device?
If it failed what was displayed on Odin logs?
If it failed, Please re-flash your device again through Odin and whether it fails OR succeeds, COPY THE LOG AND PASTE IT HERE !
I need to see the logs, if you want help.
Click to expand...
Click to collapse
It didn't fail when flashing in odin.. just stuck on samsung logo.
Read the first post. I wrote everything I did..
Entebox said:
S6 edge stuck on opening logo of "Samsung galaxy S6 edge" - it's not mine, so I can't know the history that caused it - but I think it's related to a bad try of rooting.
when trying to flash a new stock firmware from Sammobile getting the same problem - even after wipe and wipe cache.
on recovery getting this messege on the bottom:
dm-verity vertification failed... need to check DRK first...
this is what I tried to do to fix it:
1) flashed newest stock - still no do.
2) tried to flash with smart switch - it did flash - but it didn't help - phone still in bootloop.
3) flashed S6-UniKernel_v6-0001-ODIN or S6-UniBase_BOG8_v2 - it did helped, the phone worked, but I lost the IMEI and needed a certificate to fix the IMEI, I did it and the phone works fine..... BUT I can't left it with a custom rom 'cause I want the original updates and the original stock rom.
4) tried to flash the repair firmware G925FXXU1AOCV (comes with 4 files CSC, AP, MODEM and BOOTLOADER) which is 5.0.1, so it fails (tried also with pit file) - didn't do.
5) last thing I'm willing to try - is to split a new firmware to CSC MODEM BOOTLOADER and AP by myself... the only problem is - I don't actually know how to do it.
another thing I've noticed on the download mode it is written:
Current Binary: samsung Official and System status: custom
I was wonder if someone can give me a clue what to do, and how to fix this problem.
thanks!
Click to expand...
Click to collapse
You mean this post? It isn't clear enough, if you want help answer the questions people ask otherwise no one can help you.
And look, we are not talking about the device but we are talking about ODIN! Does ODIN fail or succeed flashing?
IF ODIN SUCCEEDS WITH FLASHING, THEN TELL ME!
SUCCEEDS Like This;
https://kpmgsecurity.files.wordpress.com/2014/12/odin-pass-autoroot.png
Or
FAILS Like This; http://ajqi.com/wp-content/uploads/...or-and-nand-erase-all-for-Samsung-devices.jpg
OKAY?
Entebox said:
S6 edge stuck on opening logo of "Samsung galaxy S6 edge" - it's not mine, so I can't know the history that caused it - but I think it's related to a bad try of rooting.
when trying to flash a new stock firmware from Sammobile getting the same problem - even after wipe and wipe cache.
on recovery getting this messege on the bottom:
dm-verity vertification failed... need to check DRK first...
this is what I tried to do to fix it:
1) flashed newest stock - still no do.
2) tried to flash with smart switch - it did flash - but it didn't help - phone still in bootloop.
3) flashed S6-UniKernel_v6-0001-ODIN or S6-UniBase_BOG8_v2 - it did helped, the phone worked, but I lost the IMEI and needed a certificate to fix the IMEI, I did it and the phone works fine..... BUT I can't left it with a custom rom 'cause I want the original updates and the original stock rom.
4) tried to flash the repair firmware G925FXXU1AOCV (comes with 4 files CSC, AP, MODEM and BOOTLOADER) which is 5.0.1, so it fails (tried also with pit file) - didn't do.
5) last thing I'm willing to try - is to split a new firmware to CSC MODEM BOOTLOADER and AP by myself... the only problem is - I don't actually know how to do it.
another thing I've noticed on the download mode it is written:
Current Binary: samsung Official and System status: custom
I was wonder if someone can give me a clue what to do, and how to fix this problem.
thanks!
Click to expand...
Click to collapse
Im going through the same madness for over 2 weeks...
heres my thread with a lot of amazing people tring to help....
maybe something there will help and apply to u and get urs up an running
http://forum.xda-developers.com/galaxy-s6-edge/help/bricked-s6-edge-sm-g925f-help-please-t3286385
please let me know if you get any sort of fix as i think im having same sort of bootloader issue....
Hey Ice, i didn't get your reply on ur thread sorry.
Do you have the same UniKernel as described above?
Please give me all info you have about your device and the current condition of the device (please be clear about what you can do with the device now and how you get to a certain menu such as Recovery/OdiDLmode/Smartswitch/Bootloop*kind of bootloop.)
Hope to be of good help.
curiouswrecker said:
Hey Ice, i didn't get your reply on ur thread sorry.
Do you have the same UniKernel as described above?
Please give me all info you have about your device and the current condition of the device (please be clear about what you can do with the device now and how you get to a certain menu such as Recovery/OdiDLmode/Smartswitch/Bootloop*kind of bootloop.)
Hope to be of good help.
Click to expand...
Click to collapse
Hi thanks,
have no idea about unikernel and have not tried anything with unikernel,
read someting about this somewhere else too,, something about the kernel not even loading cud be a problem?
phone is a galaxy s6 edge SM-G925F
was working fine and apparently on hungarian XEH firmware but not sure if it was on 5.02 or 5.1.1 when 16 year old kid did something or the other with it to put into bricked state.
have no idea of its previous info or condition as it was handed to me in a bricked state
only thing i can do with device is get into download mode and flash via odin...
have never ever been able to get it into recovery mode ever !!!! not even after any successful flashing
I can flash many stock files either the single tar files or either the 4 part multifirmware files
Can do flash and emergency recovery firmware through samsung smartswitch
but no matter what flash if its odin stock firmware flash or samsung smartswitch flash have never seen recovery and always can never get past the white samsung galaxy edge 6 with powered by android in white at bottom too
after succesful flashes in odin cant get out of download mode if auto reboot is ticked, only way out is to hold vol down and power. or get back into download mode then vol down to cancel/restart,
phone just never gets past that white message screen, sometimes that message will splash across screen continuouly like its turning on and off...like some sort of bootloop.... depending how i try to power/boot the phone back up again
and then sometimes it will just stay on the screen forever lit up and frozen/hanging...
strange thing that is happening now if you look at the last few attempts of flashing the 4 part multi firmware file and ticking re-partition to fix the pit files...
once i turn phone off out of download mode.... i cant power the phone/boot it up using just the power on button.
normally i assume to start the phone or turn phone on all u would need to do is hold power button.
so if phone is powered down or turned off after flash, power button alone will not turn it back on, have to go back into download mode and restart from there
i hope any of all that makes any sense at all
Here is a question for you.
When the device is OFF and you plug it into your computer, does the device then jump to the Smart Switch screen?
Btw IMPORTANT when you say that you "flash" the device through odin are you referring to the pictures on your thread where the logg states that it failed on "nand write" and once on "hidden.img" or did it actually pass after the complete flashing of all the files "hidden.img" included?
Firstly need to try this; when the device is stuck in the bootloop you have to do this.
It shows you this type of screen (1st)
http://www.pocketpc.ch/attachments/...49759183-s6-edge-bootloop-20151210_155028.jpg
(does it say kernel isn't seandroid enforced?)
Then this 2nd screen shows up
http://zidroid.com/wp-content/uploads/2014/03/Galaxy-S5-Boot-Animation.png
RIGHT after the 2nd screen SAMSUNG LOGO disappears press volume UP, HOME and POWER you need to be VERY FAST.
Then once the (1st) screen pops up again, release the POWER then volume UP and HOME buttons.
Maybe it's possible that it'll jump into recovery, even if it does this is not the solution just a way to diagnose.
Don't worry we'll fix it!
---------- Post added at 02:00 AM ---------- Previous post was at 01:10 AM ----------
If you have to flash it in any way to get it in a bootloop then the test isn't required! Don't do it.
Try the XDAdevelopers application!
icecoolpsyco said:
Hi thanks,
have no idea about unikernel and have not tried anything with unikernel,
read someting about this somewhere else too,, something about the kernel not even loading cud be a problem?
phone is a *GALAXY S6 EDGE SM-G925F*
was working fine and apparently on hungarian XEH firmware but not sure if it was on 5.02 or *5.1.1*
i hope any of all that makes any sense at all
Click to expand...
Click to collapse
This is what i gathered for you guys as a possible fix, it would work 100% if you guys didn't mess with EVERYTHING IN ODIN!
Because i have tested it myself several times.
READ EVERYTHING CLEARLY
4# When you mess with an s6 to the point that it does not turn on anymore and it only reacts until you plug it into a computer then it shows a screen "error occurred during update use Smart Switch..."
Well by that point Smart Switch mode partially takes over and you can only flash the device successfully in Smart Switch mode using Odin on the computer NOT Smart Switch.
(this knowledge will be useful later)
!!! PART 1 !!!
Here we go, follow this in detail.
STEP 1. You need to download the original Odin 3.10.6 from XDA here below:
http://forum.xda-developers.com/attachment.php?attachmentid=3109599&d=1420980613
STEP 2. Download the Kernel below:
http://mirror31.downloadandroidrom....nibase/S6-UniBase_BOG8_v2.tar?token=514002462
STEP 3. Open Odin on your computer as administrator.
STEP 4. Now connect your device to your computer.
STEP 5. Put your device/phone in Odin mode.
(volume down, home and power)
STEP 6. Make sure Odin has detected the device.
STEP 7. Load the Kernel in "AP" and wait 1 minute, then click START.
It should say PASS! However if it does not succeed, reboot the device and try it again in Smart Switch mode.
(It should actually pass the first try if these simple instructions are followed properly)
_____________________________________________
!!!PART 2!!!
STEP 1. Download this Firmware below:
http://www.sammobile.com/firmwares/download/62003/G925FXXU3QOKN_G925FVFG3QOKN_VDF/
STEP 2. Open Odin as administrator.
STEP 3. Connect your device to your computer.
STEP 4. Put your device/phone into Odin mode.
(volume down, home, power)
STEP 5. Make sure Odin has detected your device.
STEP 6. Load the Firmware in Odin "AP" and WAIT a few minutes UNTIL Odin is done reading the file. THEN CLICK on START and install the Firmware!
!!! IMPORTANT !!!
1st Possibility, if Odin shows "FAIL" "hidden.img" then that's a GOOD THING!
your phone is allmost fixed.
(Let me know if that happens.)
2nd Possibility, if Odin stops at "Nand Write" you must start over, unplug your device make sure it's OFF, then plug it back into the computer in order to boot the DEVICE into SMART SWITCH MODE and then follow the "STEPS 2,3,5,6" again!
DO NOT FOLLOW "STEP 4" Leave the device in SMART SWITCH MODE. (read above "4#")
HOWEVER
If Odin shows "PASS" then DO NOT UNPLUG the DEVICE! Go get yourself a coffee your device should be perfectly fixed!
Just unplug it AFTER A FEW MINUTES and try to switch it on, if it doesn't boot up? All you need to do is replug it into the computer and see if it boots up by itself (this does occur sometimes).
!!! LET US KNOW !!!
You can proceed rooting your device ask for help for a complete root guide for this specific device/model SM-G925F.
EDITED AND SIMPLIFIED.
Try the XDAdevelopers application!
curiouswrecker said:
This is what i gathered for you guys as a possible fix, it would work 100% if you guys didn't mess with EVERYTHING IN ODIN!
Because i have tested it myself several times.
READ EVERYTHING CLEARLY
4# When you mess with an s6 to the point that it does not turn on anymore and it only reacts until you plug it into a computer then it shows a screen "error occurred during update use Smart Switch..."
Well by that point Smart Switch mode partially takes over and you can only flash the device successfully in Smart Switch mode using Odin on the computer NOT Smart Switch.
(this knowledge may be useful later)
!!! PART 1 !!!
Here we go, follow this in detail.
STEP 1. You need to download the original Odin 3.10.6 from XDA here below:
http://forum.xda-developers.com/attachment.php?attachmentid=3109599&d=1420980613
STEP 2. Download the Kernel below:
http://mirror31.downloadandroidrom....nibase/S6-UniBase_BOG8_v2.tar?token=514002462
STEP 3. Open Odin on your computer as administrator.
STEP 4. Now connect your device to your computer, put your device/phone in Odin mode.
(volume down, home and power)
STEP 5. Make sure Odin has detected the device.
STEP 6. Load the Kernel in "AP" and wait 1 minute, then click START.
It should say PASS! However if it does not succeed, reboot the device and try it again in Smart Switch mode.
(It should actually pass the first try if these simple instructions are followed properly)
_____________________________________________
!!!PART 2!!!
STEP 1. Download this Firmware below:
http://www.sammobile.com/firmwares/download/62003/G925FXXU3QOKN_G925FVFG3QOKN_VDF/
STEP 2. Open Odin as administrator.
STEP 3. Connect your device to your computer, Put your device/phone into Odin mode.
(volume down, home, power)
STEP 4. Make sure Odin has detected your device.
STEP 5. Load the Firmware in Odin "AP" and wait a few minutes, when Odin is done reading the file click on START and install the Firmware.
!!! IMPORTANT !!!
1st Possibility, if Odin shows "FAIL" "hidden.img" then that's a GOOD THING!
your phone is allmost fixed.
(Let me know if that happens.)
2nd Possibility, if Odin stops at "Nand Write" you must start over, unplug your device make sure it's OFF, then plug it back in to the computer in order to boot the DEVICE into SMART SWITCH MODE and then follow the 5 STEPS again ONLY THIS TIME DO NOT BOOT THE DEVICE INTO ODIN MODE! Leave it in SMART SWITCH MODE.
(read above "4#")
If Odin shows "PASS" then DO NOT UNPLUG the DEVICE! Go get yourself a coffee your device should be perfectly fixed!
!!! LET US KNOW !!!
You can proceed rooting your device ask for help for a complete root guide.
Try the XDAdevelopers application!
Click to expand...
Click to collapse
I did flash that UniBase kernel and because of this I've lost the Imei number... I had to use Jtag box to recover the Imei.
so Beware when flashing this kernel.
I will try to flash the stock rom from sammobile... Hope it will help.
curiouswrecker said:
You mean this post? It isn't clear enough, if you want help answer the questions people ask otherwise no one can help you.
And look, we are not talking about the device but we are talking about ODIN! Does ODIN fail or succeed flashing?
IF ODIN SUCCEEDS WITH FLASHING, THEN TELL ME!
SUCCEEDS Like This;
https://kpmgsecurity.files.wordpress.com/2014/12/odin-pass-autoroot.png
Or
FAILS Like This; http://ajqi.com/wp-content/uploads/...or-and-nand-erase-all-for-Samsung-devices.jpg
OKAY?
Click to expand...
Click to collapse
when I flash it passes in Odin...
only problem is - the device stuck on the first logo (powered by android).
and on download mode it shows:
Current Binary: samsung Official
System status: custom
and on recovery it shows:
dm-verity vertification failed... need to check DRK first...
I did some research also
http://forum.gsmhosting.com/vbb/f77...drk-device-root-key-not-shoving-imei-1991601/
and
http://forum.gsmhosting.com/vbb/f684/dm-verity-verification-failed-1974767/
I'm not sure what is this rootkey issue, someone said that it is damaged, therefore it shows the dm verity vertification failure.
Entebox said:
http://forum.gsmhosting.com/vbb/f77...drk-device-root-key-not-shoving-imei-1991601/
and
http://forum.gsmhosting.com/vbb/f684/dm-verity-verification-failed-1974767/
I'm not sure what is this rootkey issue, someone said that it is damaged, therefore it shows the dm verity vertification failure.
Click to expand...
Click to collapse
found another thing, will give it a try:
http://forum.xda-developers.com/not...rification-t3293306/post64808458#post64808458
I also got the "dm verity vertification failure" today, but with me it happened because I was dumb enough to flash a G920I modem and bootloader on my G925F...
So it also bootlooped and everything, and then just like what you had, it asked me for Smart Switch. But then when I used Smart Switch on it, I got firmware from a totally different country than my own (think it was from Mexico or something), as I live in the Netherlands. And it even asked me for my phone's serial number before Smart Switch went on and flashed that firmware.
So I guess they only look at the CSC or something? Anyway, after that I got it into download mode and immediately flashed the newest correct firmware, and am happily flashing ROM's again Just download your own country's 5.1.1 firmware and you'll be alright, as long as you can get into download mode
Piliip said:
I also got the "dm verity vertification failure" today, but with me it happened because I was dumb enough to flash a G920I modem and bootloader on my G925F...
So it also bootlooped and everything, and then just like what you had, it asked me for Smart Switch. But then when I used Smart Switch on it, I got firmware from a totally different country than my own (think it was from Mexico or something), as I live in the Netherlands. And it even asked me for my phone's serial number before Smart Switch went on and flashed that firmware.
So I guess they only look at the CSC or something? Anyway, after that I got it into download mode and immediately flashed the newest correct firmware, and am happily flashing ROM's again Just download your own country's 5.1.1 firmware and you'll be alright, as long as you can get into download mode
Click to expand...
Click to collapse
yeah... already flashed the newest for my country.. it flashes well but still stuck on logo after.
from some reason after flashing, on DL mode it shows :
Current Binary: samsung Official
System status: custom
so the system status refuses to become official. even after using the smartswitch software.
I think maybe some of the partitions in the eMMC are corrupted.
Entebox said:
yeah... already flashed the newest for my country.. it flashes well but still stuck on logo after.
from some reason after flashing, on DL mode it shows :
Current Binary: samsung Official
System status: custom
so the system status refuses to become official. even after using the smartswitch software.
I think maybe some of the partitions in the eMMC are corrupted.
Click to expand...
Click to collapse
I think that's because you've tripped knox (hence custom), but you do have official samsung firmware, (hence official).
Edit: Have you checked your kernel?
Btw IMPORTANT when you say that you "flash" the device through odin are you referring to the pictures on your thread where the logg states that it failed on "nand write" and once on "hidden.img" or did it actually pass after the complete flashing of all the files "hidden.img" included?
succesful flashes i mean passes, i can get many many stock files to flash and pass no problem now as wasnt the case when i first got the phone
It shows you this type of screen (1st)
http://www.pocketpc.ch/attachments/s...210_155028.jpg
thats the first screen i can never ever get past
(does it say kernel isn't seandroid enforced?) it doesnt say that... but previously when i was flashing twrp and booted tried booting the phone up it woud say recovery isnat seandroid enforcing, i dont get that no more as i am flashing stock firmwares
---------- Post added at 01:17 PM ---------- Previous post was at 01:06 PM ----------
Entebox said:
I did flash that UniBase kernel and because of this I've lost the Imei number... I had to use Jtag box to recover the Imei.
so Beware when flashing this kernel.
I will try to flash the stock rom from sammobile... Hope it will help.
Click to expand...
Click to collapse
im willing to try that method above too... but am worried about losing the imei mentioned, have also read that happen to someone else and they fixed it too but they didnt mention how, and a worried to try it too as wouldnt know how to fix the imei if it went wrong as u mentioned u used soemthing called jtag to recover and i have no idea what or how that is
Entebox said:
I did flash that UniBase kernel and because of this I've lost the Imei number... I had to use Jtag box to recover the Imei.
so Beware when flashing this kernel.
I will try to flash the stock rom from sammobile... Hope it will help.
Click to expand...
Click to collapse
NO!!!
This is the UnibaseV9 Kernel, i have tested all the files i've shared on this thread personally on Samsung s6 edge model SM-G925F!
I never lost any imei!
Just follow the steps for God's sake!
Okay I have seen various requests so I decided to hook it up, I had to pay for these but here ya go. I have full firmware for lollipop or kitakat and you can get them from the following links to my google drive.
https://drive.google.com/folderview?id=0BxcLJPerShJ_ZDJrNV9fRVBSdU0&usp=sharing
Within you will see two folders you can pick either kitkat or lollipop and to do a full flash download the files starting with ALL then flash with odin by placing in the pda section. The others shouldnt even be needed if your looking just to fully flash the device use the ones that start with the label ALL. Enjoy. Wish someone could get the bootloader unlocked for this variant. If their are any other variants that need firmware let me know ill see what i can do.
I am curious could i perhaps flash the csc for tmobile then maybe my dev settings let me unlock bootloader like tmobile variant? I am not certain but I feel like it could possibly
Any luck with that ? ? I bought this phone on Valentines Day with android 5.1.1. The first thing I did was download Your stock firmwares cuz I knew it was gonna be a start of another journey with another Samsung device with lil to no development for it. Been doing research daily since then, You've been the most helpful & informative for Our cricket variant of the Grand Prime.
two559 said:
Any luck with that ? ? I bought this phone on Valentines Day with android 5.1.1. The first thing I did was download Your stock firmwares cuz I knew it was gonna be a start of another journey with another Samsung device with lil to no development for it. Been doing research daily since then, You've been the most helpful & informative for Our cricket variant of the Grand Prime.
Click to expand...
Click to collapse
Ya I am working on a few things but, honestly its going to be tough if I do happen to figure out a way for custom recovery xda forums will know first.
Helllo
I have a G530AZ, Itried to flash it with odin and it bricked. The phone doesn't turn on...not even in download mode....What can I do??. Can anyone help me...
edyrod84 said:
I have a G530AZ, Itried to flash it with odin and it bricked. The phone doesn't turn on...not even in download mode....What can I do??. Can anyone help me...
Click to expand...
Click to collapse
If I doesn't turn on at all. Then it's bricked. To make sure. Switch the battery or charge it. If it still doesn't turn on there is nothing you can do. But if you can get into Odin and download mode. There is hope and I have the files you'll need to salvage it.
Has anyone had any luck rooting this damn SM-G530AZ (5.1.1) ?? I've tried numerous methods and suggestions but so far this thing just won't give in....
EvilDoer360 said:
Has anyone had any luck rooting this damn SM-G530AZ (5.1.1) ?? I've tried numerous methods and suggestions but so far this thing just won't give in....
Click to expand...
Click to collapse
I rooted mine a while back, do you still need assistance?
i need some help, is there any custom recovery i can install for this phone?, cause i wanted to install the rom in this thread with flashify but i can't do it: http://forum.xda-developers.com/gran...285mb-t3415560
Layman instructions?
I just want to root my phone so that I can save whole apps on my sd card to free up so much space.
I'm just a layman though and have no idea what's being talked about or what the files are that you're sharing. I would really appreciate step by step layman instruction. Thank you so much if you can do that!
toxinburn said:
Okay I have seen various requests so I decided to hook it up, I had to pay for these but here ya go. I have full firmware for lollipop or kitakat and you can get them from the following links to my google drive.
https://drive.google.com/folderview?id=0BxcLJPerShJ_ZDJrNV9fRVBSdU0&usp=sharing
Within you will see two folders you can pick either kitkat or lollipop and to do a full flash download the files starting with ALL then flash with odin by placing in the pda section. The others shouldnt even be needed if your looking just to fully flash the device use the ones that start with the label ALL. Enjoy. Wish someone could get the bootloader unlocked for this variant. If their are any other variants that need firmware let me know ill see what i can do.
Click to expand...
Click to collapse
Hey, do you have a nandroid backup of your device (sm-g530az) that you could give me? My Samsung is dead, odin don?t recognize my device in download mode, only boot in recovery, and I can flash it with cwm. Please, you could help me?
VickMadrid said:
Hey, do you have a nandroid backup of your device (sm-g530az) that you could give me? My Samsung is dead, odin don?t recognize my device in download mode, only boot in recovery, and I can flash it with cwm. Please, you could help me?
Click to expand...
Click to collapse
their is no bootloader unlock or custom recovery for the 530az that i am aware of, so i never could make a nandroid backup. If you know of a way to actually use a custom recovery etc on the 530az I would make you a backup.
toxinburn said:
their is no bootloader unlock or custom recovery for the 530az that i am aware of, so i never could make a nandroid backup. If you know of a way to actually use a custom recovery etc on the 530az I would make you a backup.
Click to expand...
Click to collapse
That´s the history. I recieve the samsung (sm-g530az), but the smartphone don´t connect to wifi, when you choose the network only appear "Saved, Protected". No matter how much times you select the network, always appear the same thing and the device do nothing. Well, i thinked in that moment in change the firmware. I read in this forum a possible solution, that solution says "Download the Samsung Kies, then connect your device and select -upgrade your device-. Type your model and S/N, and Kies does the rest". I did it, everything seemed fine, until the process stopped. And an error message appears that says "Disconnect the phone and retire the battery, then turn on + ^ + home to start the emergency recovery". I did it all, but when i connect it, my pc, odin and kies don´t recognize it, my Samsung died. I put the phone in download mode and nothing happens. I reinstall the driver, kies and everything and odin at last recognize my device. Then I dowloaded "Philiz Touch Recovery" and I could flash it with odin. After all, I clean my device and prepare it for a custom rom. I installed it "cyanogenmod 12.1 unofficial", but when restart the device, it doesn't enter to the system, only boot in recovery or bootloader. But my pc don´t recognize my device in download mode, and I can´t flash it with odin. So I need the backup to restore my device.
Try to install "Philiz Touch Recovery" with Odin. I did it, and works for me. When I recieved the samsung, i don´t unlocked the device and I could flash the CWM. Thanks for your response
VickMadrid said:
That´s the history. I recieve the samsung (sm-g530az), but the smartphone don´t connect to wifi, when you choose the network only appear "Saved, Protected". No matter how much times you select the network, always appear the same thing and the device do nothing. Well, i thinked in that moment in change the firmware. I read in this forum a possible solution, that solution says "Download the Samsung Kies, then connect your device and select -upgrade your device-. Type your model and S/N, and Kies does the rest". I did it, everything seemed fine, until the process stopped. And an error message appears that says "Disconnect the phone and retire the battery, then turn on + ^ + home to start the emergency recovery". I did it all, but when i connect it, my pc, odin and kies don´t recognize it, my Samsung died. I put the phone in download mode and nothing happens. I reinstall the driver, kies and everything and odin at last recognize my device. Then I dowloaded "Philiz Touch Recovery" and I could flash it with odin. After all, I clean my device and prepare it for a custom rom. I installed it "cyanogenmod 12.1 unofficial", but when restart the device, it doesn't enter to the system, only boot in recovery or bootloader. But my pc don´t recognize my device in download mode, and I can´t flash it with odin. So I need the backup to restore my device.
Try to install "Philiz Touch Recovery" with Odin. I did it, and works for me. When I recieved the samsung, i don´t unlocked the device and I could flash the CWM. Thanks for your response
Click to expand...
Click to collapse
ya i think you messed up royally, their is no working philz or cwm for the 530AZ at all because the bootloader is locked soooo i dont see how you ever flashed it with that in the first place, but if you indeed were able to then it looks like you have a soft brick of sorts since the bootloader is locked on that model, their is firmware but you for some reason are unable to flash with odin so sadly I am not sure what else you could do other than maybe see if it is recognized on other usb ports or computer also check your device manager in windows and check and see if the usb device is listed if it shows a yellow exclamation or unknown device then manually update the driver for the unknown device as an android device
VickMadrid said:
Hey, do you have a nandroid backup of your device (sm-g530az) that you could give me? My Samsung is dead, odin don?t recognize my device in download mode, only boot in recovery, and I can flash it with cwm. Please, you could help me?
Click to expand...
Click to collapse
Since Odin won't recognize it
Give this a shot
http://forum.xda-developers.com/grand-prime/development/fix-g530-debrick-img-guide-to-make-t3422115
[Edit]didn't realize that comment was so old xD [/Edit]
Help!!
Autolounge said:
I rooted mine a while back, do you still need assistance?
Click to expand...
Click to collapse
I do! I have the 5.1.1 530AZ and no method for has worked, please let me know what you did.
benash2010 said:
I do! I have the 5.1.1 530AZ and no method for has worked, please let me know what you did.
Click to expand...
Click to collapse
That is the exact model I have so this should work! Use KingRoot but the desktop variant. And if that doesn't work use KingRoot, again the desktop variant. Let me know how it goes!
VickMadrid said:
That´s the history. I recieve the samsung (sm-g530az), but the smartphone don´t connect to wifi, when you choose the network only appear "Saved, Protected". No matter how much times you select the network, always appear the same thing and the device do nothing. Well, i thinked in that moment in change the firmware. I read in this forum a possible solution, that solution says "Download the Samsung Kies, then connect your device and select -upgrade your device-. Type your model and S/N, and Kies does the rest". I did it, everything seemed fine, until the process stopped. And an error message appears that says "Disconnect the phone and retire the battery, then turn on + ^ + home to start the emergency recovery". I did it all, but when i connect it, my pc, odin and kies don´t recognize it, my Samsung died. I put the phone in download mode and nothing happens. I reinstall the driver, kies and everything and odin at last recognize my device. Then I dowloaded "Philiz Touch Recovery" and I could flash it with odin. After all, I clean my device and prepare it for a custom rom. I installed it "cyanogenmod 12.1 unofficial", but when restart the device, it doesn't enter to the system, only boot in recovery or bootloader. But my pc don´t recognize my device in download mode, and I can´t flash it with odin. So I need the backup to restore my device.
Try to install "Philiz Touch Recovery" with Odin. I did it, and works for me. When I recieved the samsung, i don´t unlocked the device and I could flash the CWM. Thanks for your response
Click to expand...
Click to collapse
Hello, I know is late. Is already 2017 happy new year. But i was looking the post and reading the thread. I'm looking this information to try on my friend phone that want to root. Anyway. I maybe have a solution to fix the bootloop. since you went to philz recovery. There is a bug with philz recovery. If im correct. But i got it fixed with some zip file and using command on that flash. If you still need this solution let me know. I can post the zip file and step by step of the command.
Let me know
apk
Sorry for the file "CROM_Service.apk" for what?
Hey I need that!
Kangrito said:
Hello, I know is late. Is already 2017 happy new year. But i was looking the post and reading the thread. I'm looking this information to try on my friend phone that want to root. Anyway. I maybe have a solution to fix the bootloop. since you went to philz recovery. There is a bug with philz recovery. If im correct. But i got it fixed with some zip file and using command on that flash. If you still need this solution let me know. I can post the zip file and step by step of the command./
Let me know
Click to expand...
Click to collapse
HEY I REALLY NEED THAT!
I don't have the actual CWM on my phone yet. I just got it today. I already have it rooted, deodexed, and debloated(somewhat).
I was able to root it using kingroot. I'm still working for a way to replace the newest kingroot(5.1.0) with SuperSU.
But my question is does it actually work? Have you flashed the tar with odin and fix the code in it with commands.
Just reading your post gives me chills honestly. I like doing things as soon as I can! I'm a phoneaholic.