the situation is today can update to 5.1.1 Mine meal with TWRP . but due to the fault can not get up to send a message . XDA load on the table so I preprooted ( flashable - prerooted Z3V with mods.zip 5.1.1 ) . then reboot into TWRP his actions : wipe > advance wipe > click : davik cache , system , cahe . wait for it to run is complete, select the file to install Z3V flashable - prerooted 5.1.1 with mods.zip had put in the memory . ok but it does not install dc error .
then restart the computer hangs at the SONY logo . fim1 pressed his source + volume ( - ) , the entry into the system recovery dc something few lines
Power up continue
safe mode
power dow
factory reset
dow only power line is always turned off the machine while the other lines also restart and hang SONY logo .
. do you know how to fix it yourself with only .
songphuongnet said:
the situation is today can update to 5.1.1 Mine meal with TWRP . but due to the fault can not get up to send a message . XDA load on the table so I preprooted ( flashable - prerooted Z3V with mods.zip 5.1.1 ) . then reboot into TWRP his actions : wipe > advance wipe > click : davik cache , system , cahe . wait for it to run is complete, select the file to install Z3V flashable - prerooted 5.1.1 with mods.zip had put in the memory . ok but it does not install dc error .
then restart the computer hangs at the SONY logo . fim1 pressed his source + volume ( - ) , the entry into the system recovery dc something few lines
Power up continue
safe mode
power dow
factory reset
dow only power line is always turned off the machine while the other lines also restart and hang SONY logo .
. do you know how to fix it yourself with only .
Click to expand...
Click to collapse
You are only supposed to do all of the wipes and everything BEFORE you flash any ROM. You wipe after flash means your phone has no operating system, and you have to use Flashtool and flash a stock rom to work with.
I was facing trial versions
23.0.E.0.376
23.1.D.0.059
23.4.B.0.319
3-4 error is flash feature line , then restart dt keeps crashing .
use the PC companion not support this model . it asked to use the Software Upgrade Assistant verizon . Where do but Verizon Software Upgrade Assistant software . verizon always on site and did not find any download.
Further misery service center SONY Vietnam also no software support .
Probably not dispose of the phone now .
I live in Vietnam
Download a stock ftf file and flash it using the flashtool. You can find both files in the root guide posted before.
To use the flashtool plug your phone into your computer and hold both power buttons and the power button to put the phone into flash mode. When your phone is in flash mode, click the flash icon in the upper left corner of the flashtool and choose flash mode. Then choose the firmware to flash.
Related
Hi,
I just got my phone, and one of the first think I did, was to start updating to latest firmware on Kies. This seemed to get stuck for hours so i disconnected the USB cable, and after that, all that happens when i start the phone is that I see a phone and a computer symbol with a warning triangle in the middle.
I have tried emergency restore in Kies, but cant get into this mode (vol up,home, On/off button ?). I suppose I somehow have to reset my phone, but how am I to do this now?
If you are wanting to do a Factory Reset then, *2767*3855#. And you should press Volume Down+Home+Power key to enter Download mode I guess.
Regards.
I cant dial any number because all I see when i turn it on is that screen i described with some symbols. I do manage to get it into download mode, but I dont really dont know where to go from here to restore everything. Kies tells me I need emergency restore, but I cant get into this mode...
phone off vol up = home + power hold down until splash screen and release .
Then wipe data and factory reset.
That fails service centre next .
jje
JJEgan said:
phone off vol up = home + power hold down until splash screen and release .
Then wipe data and factory reset.
That fails service centre next .
jje
Click to expand...
Click to collapse
When i Try the combo vol up+home+power nothing happens other then the phone starting with the symbols.I suppose this combo doesn't work on my phone, at least if I am not doing it horribly wrong.
As soon as you get a display release vol up + home followed by pwr .
jje
I have tried what you are saying several times, but I am still stuck at the screen with the symbols:/
edit: this is how my screen looks: http://forum.xda-developers.com/wiki/index.php?title=File:Samsung_Galaxy_S_Black_Screen_of_Death.jpg
I have tried to flash the firmware in ODIN but that gets stuck at zimage.
Now i fixed my problem by flashing to branded original kernel from Orange. I have realized I am not able to update this though, and I dont want all these useless apps preinstalled. Therefore I have tried to flash to EU unbranded ROMs like XWKE7. But when I am doing this, Odin always gets stuck.
Is there anything I should do before I flash one of these ROMs (yes I am new to this...)?
I am sorry to spam my own thread, but now my phone got locked up by the same symbols again, but this time I cant manage to flash back to original orange kernel. Each time i try to flash, the process gets stuck at zimage or some other point.
Any ideas how to fix? Or have i bricked my phone?:/
Start at the beginning .
Boot to recovery mode Advanced Wipe Dalvik Cache .
Mounts and storage Format data system sd card .
No recovery on phone just wiper data and factory reset .
Power phone off source stock rom from stock roms post in dev section set up Odin .
Boot phone to download mode connect cable and flash rom .
Or
http://forum.xda-developers.com/showthread.php?t=1108499
That fails its a service centre .
jje
JJEgan said:
Start at the beginning .
Boot to recovery mode Advanced Wipe Dalvik Cache .
Mounts and storage Format data system sd card .
No recovery on phone just wiper data and factory reset .
Power phone off source stock rom from stock roms post in dev section set up Odin .
Boot phone to download mode connect cable and flash rom .
Or
http://forum.xda-developers.com/showthread.php?t=1108499
That fails its a service centre .
jje
Click to expand...
Click to collapse
I didnt quite get what you were saying there. I have wiped my phone with recovery, but when I try to flash any ROM with ODIN the process stops after a few seconds, and I have to flash my original Kernel to get things to work. Any thoughts on this?
Edit: I figured my "fix" was using another PC with another USB port, because my current pc seems to hate my SG2 device
I have made system reset in rec mode ( volume up + turn on + home buttons ) . also factory reset and after reboot i can't turn on my galaxy, it is stuck on the name GT 9300 when it turns on. i am new in android system and can anyone explain what shoult i do ?
system reset what do you mean as you have factory reset .
First thoughts are that you have wiped your phone of all data and OS .
Please boot to download mode and post product name as shown .
jje
If you made a system reset(formatted /system), you deleted your os, made your phone totally clean.. You have to flash a new rom, if hou want a stock one, go to sammobile.com
You have to download Odin3 v1.85 and the rom for your carrier..
1.Put the phone to download mode by pressing and holding Vol Up+Home+Power for 10 seconds then press up.
2.Open odin -> connect your phone to PC
3.click pda button and choose the rom file which should be .md5
4.make sure only auto reboot and f.reset time are checked(and pda ofc)
5.click start
Your phone should boot up..
Hope it was helpful.
Greetings
Sent from my GT-I9300 using Tapatalk 2
tornike14 said:
I have made system reset in rec mode ( volume up + turn on + home buttons ) . also factory reset and after reboot i can't turn on my galaxy, it is stuck on the name GT 9300 when it turns on. i am new in android system and can anyone explain what shoult i do ?
Click to expand...
Click to collapse
I Guess you used.. Philz recovery and did a Complete wipe..! If yess.. You will have to reinstall Stock rom.. as the steps mentioned above..
Well ! To start with, I was already using "Honami MW HD™ V8 Ultimate" by Pandemic and my phone was working great untill i tried installing this ROM ( http://forum.xda-developers.com/xperia-u/u-development/rom-cyanogenmod-11-0-t2528466 ).I followed every instruction to every word which was:
1. Download ROM zip and GApps zip.
2. Boot into recovery.
3. Wipe data and cache and Dalvik.
4. Flash ROM zip.
5. Flash GApps zip. You must flash gapps after every upgrade to CM11 since /system is formatted, wiping your previous add-ons.
6. Reboot.
While flashing the ROM zip, i was stuck with "status 7" error. To get rid of this error i followed this link(http://forum.xda-developers.com/showthread.php?t=2522762) which instructed me to delete the whole of "assert" module. I did what was instructed and i flashed the ROM. The ROM was succesfully installed and so did the GApps but finally while rebooting my phone got bricked.
Only the orange LED blinked whenever i pressed the power button and thats it . After loads of browsing and searching, i found out that my phone was hard bricked and it needs to be flashed .
I downloaded the ftf from this link ( http://forum.xda-developers.com/xpe...-official-ics-firmware-xperia-sola-6-t1914264 ) and i followed the following procedures:
"
Download official ics ftf from development section of ur xperia
Download flashtool
Install flashtool
Go to c/flashtool/drivers
Install drivers for ur xperia
Now switch of ur phone keep it aside
Go to flashtool
Click thunder icon
Select flashmode
Select ftf
Check no final verification
Check exclude ta
Click flash\start
Now it will ask u to connect ur phone in flashmode
Press the volume down button, keep it pressed and connect to usb
Flashing will start
Let it complete
U r done wait for flashing "
I pressed the "vol up + power" until 3 continuous vibrations and then "vol down" at same time i plugged the USB cable(LED turned green), the flash process started and it was finished successfully. I unpluged my USB and i pressed the power , the phone still does'nt start/boot.
I would really appreciate for all the help that i can get to recover this phone.
I rooted my phone ( XPERIA ION ) a days back and also install CWM recovery, it was working fine.
But Something went wrong I just open a link and my phone switched off and never boot again.
even it is not booting in Recovery mode.
But it vibrates when I continously press power button and a green light appear.
Is this is the condition of hard brick or something else.
Please help what are the option available now ?
Flash Stock firmware .ftf file by using Flashtool
Pa1 said:
I rooted my phone ( XPERIA ION ) a days back and also install CWM recovery, it was working fine.
But Something went wrong I just open a link and my phone switched off and never boot again.
even it is not booting in Recovery mode.
But it vibrates when I continously press power button and a green light appear.
Is this is the condition of hard brick or something else.
Please help what are the option available now ?
Click to expand...
Click to collapse
1. First Download the stock firmware from here http://forum.xda-developers.com/wiki/Sony_Xperia_ion
2. Download Flashtool from here http://www.flashtool.net/download.php for whatever platform suits you.
3. Install Flashtool and open it .
4. Connect device in Flash mode ( by pressing volume down (-) button while connecting to USB ).
5. Go to C:/Flashtool/Driver and run it.
6. Install Flashtool drivers, Fastboot drivers and (" your device ") Drivers.
7. Now copy the stock firmware (file_name.ftf ) and paste inside Firmware folder present in C:/Flashtool.
8. GO to Flashtool click on flash icon --> select your firmware .
9. At last click on Flash , it almost take 2-3 minutes.
### Unplug your device and boot it, it will definitely boot. ###:good:
Hello, I think I´ve got a serious problem with my Huawei Ascend Mate 7.
I bought it as software damaged and hoped to fix it, but it seems to be more difficult as expected.
When it attempts to boot up following error-message ist displayed:
Rescue-mode
Attention, please update System again.
Func No: 9 (FUNC_BOOT_KERNEL)
Error NO : 2
When I want to enter the recovery with power button and volume up, there is also a error message as following:
Func No : 10 (FUNC_BOOT_RECOVERY)
Error No: 2
Even the force update 3 buttons method doesn't work either.
When I put the UPDATE.APP in the dload folder in the root of the SD-card and attempt to perform the update its stuck at the Huawei "power on" logo.
I also tried to flash different recovery and boot.imgs (from different versions TL09, TL00 -->because I don´t exactly know which one I own -->the pre-owner replaced the battery-housing (which indicates the TL00 version, and the sticker of the original package shows the TL09 version.
It doesn't matter which recovery or boot img I flashed every time the same error-message ist displayed. Even i was not able to enter the recovery. (But fastboot recognition and executing commands like "flash" and so on works)
So I am out of ideas, every kind of help is appreciated.
Thread moved to proper forum.
Hello
Did you restore your phone to life?
Because I have the same problem and tried everything already.
Regards
Hello,
no i sold it as damaged.
what is the soltion????
i brought the phone back to life getting this error too.
look carefully at e error boot kernel msg,it says go to the website n download some files too,so i went ahead n downloaded some kernel files for my huawei mate 7.. i installed the firmware stock rom too for my huawei. note* this 2 files r impt to revive yr phone after getting this msg*
have yr fastboot downloaded n install twrp recovery.(pls download the correct version for yr huawei,mine is mate 7) & rename it recovery.img n place the file in the fastboot route, while e route file window is opened now, hold down shift n right click yr mouse n select edit command prompt here..
next.. plug usb into yr com n connect it to yr phone, now hold both vol - & power button key to get into fastboot mode n go ahead n flash the recovery.img by typing this command(fastboot flash recovery recovery.img)
after success of flashing,hold BOTH vol + & power button ,release both when you see boot logo. twrp teamwin shd show up (n went ahead wipe/factory reset.*note if u nd to backup,u should!* i reckon my batt is low,so i use the twrp(power off) option n viola it finally get charged up becos previously it wont charge at all. so i charged to 100% .
next..remember the 2 files i downloaded earlier? i throw them into my clean SD CARD(yes i formatted them incase there's too much rubbish n updating wont catch e files i downloaded) and slot into the phone n power off my phone. now, hold the 3 buttons, vol + vol - & powerkey, n VIOLA! updating should start n yr phone is back to life!!
previously my phone lags, after installing the stock firmware and the kernel. everything went so smoothly, i reckon the default rom is an old version. so in short ******just download a proper stock rom & kernel for yr huawei, dont unzip, just throw them into SD card n update by holding down all the buttons . or maybe full battery 100% does e trick if you already know how to revive them. try both! Good luck !
ITger_ling said:
i brought the phone back to life getting this error too.
look carefully at e error boot kernel msg,it says go to the website n download some files too,so i went ahead n downloaded some kernel files for my huawei mate 7.. i installed the firmware stock rom too for my huawei. note* this 2 files r impt to revive yr phone after getting this msg*
have yr fastboot downloaded n install twrp recovery.(pls download the correct version for yr huawei,mine is mate 7) & rename it recovery.img n place the file in the fastboot route, while e route file window is opened now, hold down shift n right click yr mouse n select edit command prompt here..
next.. plug usb into yr com n connect it to yr phone, now hold both vol - & power button key to get into fastboot mode n go ahead n flash the recovery.img by typing this command(fastboot flash recovery recovery.img)
after success of flashing,hold BOTH vol + & power button ,release both when you see boot logo. twrp teamwin shd show up (n went ahead wipe/factory reset.*note if u nd to backup,u should!* i reckon my batt is low,so i use the twrp(power off) option n viola it finally get charged up becos previously it wont charge at all. so i charged to 100% .
next..remember the 2 files i downloaded earlier? i throw them into my clean SD CARD(yes i formatted them incase there's too much rubbish n updating wont catch e files i downloaded) and slot into the phone n power off my phone. now, hold the 3 buttons, vol + vol - & powerkey, n VIOLA! updating should start n yr phone is back to life!!
previously my phone lags, after installing the stock firmware and the kernel. everything went so smoothly, i reckon the default rom is an old version. so in short ******just download a proper stock rom & kernel for yr huawei, dont unzip, just throw them into SD card n update by holding down all the buttons . or maybe full battery 100% does e trick if you already know how to revive them. try both! Good luck !
Click to expand...
Click to collapse
when i trying to flash this error each thime
Failed remorte: command not allowed