Phone bricked, flashing red led and "Qualcomm 900E" - Xiaomi Redmi Note 3 Questions & Answers

I recently unlocked my bootloader unoffical using a guide here and it all went well until I flashed sMIUI and now it is bricked, it is recognized on my PC as Qualcomm 900E and it won't take ADB commands or show up in MiFlash

K-NineHD said:
I recently unlocked my bootloader unoffical using a guide here and it all went well until I flashed sMIUI and now it is bricked, it is recognized on my PC as Qualcomm 900E and it won't take ADB commands or show up in MiFlash
Click to expand...
Click to collapse
http://en.miui.com/thread-274589-1-1.html just read carefully and try it..having same issue but after trying the method given in point 2 pc starts showing 9008 driver and able to boot in edl mode ..

Related

Urgent Help.. Qualcomm HS-USB Diagnostics 900E

Hi everyone.. Can someone guide me how to get my phone to be detect back as Qualcomm HS-USB qdloader 9008 instead of this Qualcomm HS-USB Diagnostics 900E.. Actually i was flashing a rom using miflash but since i didnt select flashall below.. i made the mistake of closing the miflash before the flashing was done.. Since then i cant get the mob to be detect as qdloader so it can appear in miflash. The phone right now is still in fastboot. Please is there any way to revive my phone? :crying::crying::crying:
There is already topic with 2 methods, http://forum.xda-developers.com/redmi-note-3/how-to/unbricking-redmi-note3-hardbrickhs-usb-t3351325
il183690 said:
There is already topic with 2 methods, http://forum.xda-developers.com/redmi-note-3/how-to/unbricking-redmi-note3-hardbrickhs-usb-t3351325
Click to expand...
Click to collapse
This works for people who are able to get to fastboot. I am not able to get to fastboot at all. Only EDL. Please help. Any other alternative?
Can you please check this thread.
I hope this helps.
You remind me of myself
I did the same thing in April and had to go to service center as i couldnt make it work that time, they fixed it within 24hours
But now there are lots of recovery methods that u could try
Zed4u said:
Hi everyone.. Can someone guide me how to get my phone to be detect back as Qualcomm HS-USB qdloader 9008 instead of this Qualcomm HS-USB Diagnostics 900E.. Actually i was flashing a rom using miflash but since i didnt select flashall below.. i made the mistake of closing the miflash before the flashing was done.. Since then i cant get the mob to be detect as qdloader so it can appear in miflash. The phone right now is still in fastboot. Please is there any way to revive my phone? :crying::crying::crying:
Click to expand...
Click to collapse
Try deep flash methode, just need to buy deep flash cable in market. For the guidance, please try to googling it in miui forum due to already available there.
Yesterday, one of my friend succesfull to restore her kenzo from diagnostic mode and really happy with the result.
Try the simple deep flash method mentioned here -
http://en.miui.com/thread-310325-1-1.html
I was able to recover my rn3 from 900e mode using this.
It's very simple and easy. You just need a copper wire strand to do it.
Use Deep Flash Method
I had the exact same problem so I tried deep flash method. It worked and my phone was detected by the PC as 9008. Then I could flash the fastboot rom using Miflash tool. Hope this helps.

Remdi Note 3 (kenzo) completely dead

Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
Try again to boot in fastboot mode by pressing vol down + power button for 10 to 20 second if booted into fastboot then release buttons
Try to unlock your device from mi unlock tool
Then it must boot
Try going to Fastboot Mode using Power Button and Vol Down. If you can go to Fastboot, then I'm pretty sure you'll be able to go to EDL Mode. Just look up online how to go to EDL Mode from Fastboot. I think the command to be typed in the cmd window is 'fastboot reboot edl'.
If that works, and you have your Qualcomm drivers installed, you should be able to flash a Fastboot ROM using Mi Flash Tools.
Cheers!
[email protected] said:
Try again to boot in fastboot mode by pressing vol down + power button for 10 to 20 second if booted into fastboot then release buttons
Try to unlock your device from mi unlock tool
Then it must boot
Click to expand...
Click to collapse
I can't seem to get to fastboot or recovery using the button combinations.
It does not even power on, even though i have charged for 8 hours now.
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
manakmishra said:
I can't seem to get to fastboot or recovery using the button combinations.
It does not even power on, even though i have charged for 8 hours now.
Click to expand...
Click to collapse
Open kenzo a.k.a. redmi note 3 disconnect battery
Then connect USB just to mobile not to PC
Then connect battery don't press any button
Connect USB to PC while pressing volume up button
Start mi flash tool click on refresh button see if it detects.
Start flash
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
Simply do this : https://forum.xda-developers.com/redmi-note-3/how-to/guide-reboot-to-edl-mode-fastboot-test-t3398718
Then flash latest global dev rom in Miflash (refresh when phone isn't detected http://en.miui.com/a-234.html
since you can't boot, it might be worth your time to take a look at this.
https://forum.xda-developers.com/redmi-note-3/how-to/guide-how-to-flash-hard-bricked-redmi-t3490055
It's a tutorial to make a 'deep-flash' cable using a micro usb cable that will force your device into fastboot mode, much like samsung's USB jig.
If that works, then you can try following this tutorial :
http://en.miui.com/thread-235865-1-1.html
You can use the link given in post #6 to boot to edl, then flash a stock MIUI ROM using MiFlash.
If all else fails, it might be time to consider taking it to the Mi service centre.

[help] red light blinking

I accidentally flashed Redmi note 3 firmware into Redmi note 4. Now only red light is blinking. No fastboot also. Computer showing in ports Qualcomm hs usb qdloader 9008 (com3). Please help me flash full fastboot rom
if your computer detects your device as qdloader , that means it is in EDL mode, in this mode , you should be able to flash fastboot roms using miflash , you should read this thread first, http://en.miui.com/thread-565784-1-1.html . although the thread writes about flashing in fastboot mode, but it shouldn't differ alot from flashing in EDL mode, just follow the B part of the guide in the link, MIFlash should be able to detect your device and list it down as COM(number) .
As for the driver part, you shouldn't need to update anything if MIFlash can detect your device , as your computer already correctly detects it as QDLoader
chun_9876 said:
if your computer detects your device as qdloader , that means it is in EDL mode, in this mode , you should be able to flash fastboot roms using miflash , you should read this thread first, http://en.miui.com/thread-565784-1-1.html . although the thread writes about flashing in fastboot mode, but it shouldn't differ alot from flashing in EDL mode, just follow the B part of the guide in the link, MIFlash should be able to detect your device and list it down as COM(number) .
As for the driver part, you shouldn't need to update anything if MIFlash can detect your device , as your computer already correctly detects it as QDLoader
Click to expand...
Click to collapse
Thankyou for your valuable reply. Miflash detecting device. But error in flash. Then removed back cover and removed battery connection also. Then Miflash flashed the rom successfully

Bricked Xiaomi Redmi Note 4 (please help)

My Redmi Note 4 is hard bricked...:crying:
I unlocked the bootloader the official way and was trying to flash lineageos on it. I failed :crying:
I cant go into Fastboot mode or Recovery. The Phone wont turn on. I get the Red LED light, when i connect it with the computer.
I bought a Deep Flash Cable and connected my phone with unplugged battery. In device manager under ports i got
qualcomm hs-usb diagnostics 900e. But under MIFlash tool there was no com port. So i changed the driver of the
qualcomm hs-usb diagnostics 900e to qualcomm hs-usb qdloader 9008 (com10) and i got com10 in miflash. If i try to flash the fastboot rom (stable) i get this error: sahara read end error eith status:9. :crying:
I hope someone can help me?
Ninman20
Ninman20 said:
My Redmi Note 4 is hard bricked...:crying:
I unlocked the bootloader the official way and was trying to flash lineageos on it. I failed :crying:
I cant go into Fastboot mode or Recovery. The Phone wont turn on. I get the Red LED light, when i connect it with the computer.
I bought a Deep Flash Cable and connected my phone with unplugged battery. In device manager under ports i got
qualcomm hs-usb diagnostics 900e. But under MIFlash tool there was no com port. So i changed the driver of the
qualcomm hs-usb diagnostics 900e to qualcomm hs-usb qdloader 9008 (com10) and i got com10 in miflash. If i try to flash the fastboot rom (stable) i get this error: sahara read end error eith status:9. :crying:
I hope someone can help me?
Ninman20
Click to expand...
Click to collapse
https://www.google.com/amp/s/forum....-fix-totally-dead-redmi-note-4-t3746465/page1
Hope it helps you
Sent from my mido using XDA Labs
Ninman20 said:
My Redmi Note 4 is hard bricked...:crying:
I unlocked the bootloader the official way and was trying to flash lineageos on it. I failed :crying:
I cant go into Fastboot mode or Recovery. The Phone wont turn on. I get the Red LED light, when i connect it with the computer.
I bought a Deep Flash Cable and connected my phone with unplugged battery. In device manager under ports i got
qualcomm hs-usb diagnostics 900e. But under MIFlash tool there was no com port. So i changed the driver of the
qualcomm hs-usb diagnostics 900e to qualcomm hs-usb qdloader 9008 (com10) and i got com10 in miflash. If i try to flash the fastboot rom (stable) i get this error: sahara read end error eith status:9. :crying:
I hope someone can help me?
Ninman20
Click to expand...
Click to collapse
1. Remove the back panel then the battery connector. Keep it in that way for a while like a minute
2. Then short either the 'most effective points' or 'less effective points' following this thread . While keeping them short, connect the USB cable to the Computer, it will enter into 'download' mode suitable for miFlash/QFIL

Help unbricking Lenovo Tab 4 10 TB-X304F

Hi. I have a Lenovo TB-X304F that I unlocked and flashed successfully with TWRP, but I screwed up and then managed to brick the device. It now goes to black screen after showing the Lenovo boot image briefly. However I can still access Fastboot and Recovery.
I did backup Boot, Data and System before all this and I have restored these succesfully via TWRP, but the device still won't boot and is stuck on the black screen.
I want to flash stock rom again, and I have downloaded "Lenovo Tab4 A10-TB-X304F_S000038_170703_ROW_QFIL" which is available from some websites, and this is meant to be flashed with QFIL. The problem is that when connecting the tablet, QFIL is always stuck with port "Qualcomm HS-USB Diagnostics 900E (COM21)" which results in the error "Download fail:Switch to EDL fail Failed to switch to Emergency Download mode" when I try to download the firmware. It seems some have solved this issue by modifying a USB cable, but I'm unsure if this would actually help me.
Can anyone help me resolve this, please? Could it be possible to get a TB-X304F backup that perhaps works, when for some reason my backup doesn't? Does somebody have a stock rom that can be flashed using ADB or TWRP?
Very grateful for any help with this. Thanks.
Try using MiFlash not Qfil to flash stock
https://www.xiaomiflash.com/
rhaavin said:
Try using MiFlash not Qfil to flash stock
https://www.xiaomiflash.com/
Click to expand...
Click to collapse
Thanks a lot for your reply! Do you think MiFlash can flash the file that I mentioned above, though (Lenovo Tab4 A10-TB-X304F_S000038_170703_ROW_QFIL)? I believe I was trying out MiFlash as well but it seems it requires another type of file to flash?
deleted
unbrick "dead" tablet Lenovo TB 4 10.1 (X304F/L)
I managed to identify the test point on the motherboard. This allows the tablet to switch from Qualcomm HS-USB Diagnostics 900E driver mode to Qualcom HS-USB QDLoader 9008 mode. My tablet could not be booted into bootloader, recovery or system...
forum.xda-developers.com

Categories

Resources