Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
Try again to boot in fastboot mode by pressing vol down + power button for 10 to 20 second if booted into fastboot then release buttons
Try to unlock your device from mi unlock tool
Then it must boot
Try going to Fastboot Mode using Power Button and Vol Down. If you can go to Fastboot, then I'm pretty sure you'll be able to go to EDL Mode. Just look up online how to go to EDL Mode from Fastboot. I think the command to be typed in the cmd window is 'fastboot reboot edl'.
If that works, and you have your Qualcomm drivers installed, you should be able to flash a Fastboot ROM using Mi Flash Tools.
Cheers!
[email protected] said:
Try again to boot in fastboot mode by pressing vol down + power button for 10 to 20 second if booted into fastboot then release buttons
Try to unlock your device from mi unlock tool
Then it must boot
Click to expand...
Click to collapse
I can't seem to get to fastboot or recovery using the button combinations.
It does not even power on, even though i have charged for 8 hours now.
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
manakmishra said:
I can't seem to get to fastboot or recovery using the button combinations.
It does not even power on, even though i have charged for 8 hours now.
Click to expand...
Click to collapse
Open kenzo a.k.a. redmi note 3 disconnect battery
Then connect USB just to mobile not to PC
Then connect battery don't press any button
Connect USB to PC while pressing volume up button
Start mi flash tool click on refresh button see if it detects.
Start flash
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
Simply do this : https://forum.xda-developers.com/redmi-note-3/how-to/guide-reboot-to-edl-mode-fastboot-test-t3398718
Then flash latest global dev rom in Miflash (refresh when phone isn't detected http://en.miui.com/a-234.html
since you can't boot, it might be worth your time to take a look at this.
https://forum.xda-developers.com/redmi-note-3/how-to/guide-how-to-flash-hard-bricked-redmi-t3490055
It's a tutorial to make a 'deep-flash' cable using a micro usb cable that will force your device into fastboot mode, much like samsung's USB jig.
If that works, then you can try following this tutorial :
http://en.miui.com/thread-235865-1-1.html
You can use the link given in post #6 to boot to edl, then flash a stock MIUI ROM using MiFlash.
If all else fails, it might be time to consider taking it to the Mi service centre.
Related
hey everyone, flashed the cwm recovery which i found someware and the source were saying the it meant for all devices. but npw my phone does not go to fastnoot nor to recovery mode.
But, whenever i connect it to pc the the red noti. red light blinks and device name qualcomm 900e shows up in device manager. also waiting for device in adb. is there any way to revive my phone???:crying: :crying:
Try flashing a fastboot rom using MI flash tool beta.The red light shows that it is in edl mode.
GNVM said:
Try flashing a fastboot rom using MI flash tool beta.The red light shows that it is in edl mode.
Click to expand...
Click to collapse
flashtool does not recognize the device.
also in adb there is no device in list?
jobangill99 said:
flashtool does not recognize the device.
also in adb there is no device in list?
Click to expand...
Click to collapse
Try miflash to flash a new rom. If this does not work, then remove the back panel of you phone and disconnect the battery cable. Watch video on youtube for help. After that leave the phone disconnected for 30 mins and then reconnect it. Press vol down and power and you should be able to enter fastboot mode.
If nothing works go for test point method. see videos for better understanding.
hey
im trying to flash global rom on my phone but i miflash does not seem to detect my phone.
i have tired reinstalling a miflash.
anyone have any ideas what could be the problem?
also could someone send me a link to a clean global rom as i my current rom has been tampered with and the seller has sent me a new rom to flash which i believe also may be tampered with..
Have you unlocked your bootloader yet?
Sent from my Redmi 3 using Tapatalk
GrimEire said:
hey
im trying to flash global rom on my phone but i miflash does not seem to detect my phone.
i have tired reinstalling a miflash.
anyone have any ideas what could be the problem?
also could someone send me a link to a clean global rom as i my current rom has been tampered with and the seller has sent me a new rom to flash which i believe also may be tampered with..
Click to expand...
Click to collapse
if you want to flash on locked bootloader then you need to be in edl mode not in fastboot mode.to be in edl mode turn off your phone.plug the usb cable to the computer.now get ready to to plug it into the phone but before that be ready to press both volume buttons.this is important step ok.keep your fingers on both volume up and down buttons.now as soon as you plug the usb cable into the phone press both volume buttons.then it will vibrate bt screen will be black.now open mi flash and see there it should show com 10 or com 20 or watever com something like that.then you are ready to flash the rom.after that i hope you know the steps after this.
jokerpappu said:
if you want to flash on locked bootloader then you need to be in edl mode not in fastboot mode.to be in edl mode turn off your phone.plug the usb cable to the computer.now get ready to to plug it into the phone but before that be ready to press both volume buttons.this is important step ok.keep your fingers on both volume up and down buttons.now as soon as you plug the usb cable into the phone press both volume buttons.then it will vibrate bt screen will be black.now open mi flash and see there it should show com 10 or com 20 or watever com something like that.then you are ready to flash the rom.after that i hope you know the steps after this.
Click to expand...
Click to collapse
On Windows you usually have to install drivers because windows usually don't recognize device as something connected through com port. This could be done through device manager, install drivers for unknown device, browse for location and they are in drivers directory in miflash directory.
Sent from my Redmi 3 using Tapatalk
kosiiik said:
On Windows you usually have to install drivers because windows usually don't recognize device as something connected through com port. This could be done through device manager, install drivers for unknown device, browse for location and they are in drivers directory in miflash directory.
Sent from my Redmi 3 using Tapatalk
Click to expand...
Click to collapse
I just let windows find the driver and they do.it automatically if u have internet connection ok.why work hard when it can be simple
It has never worked for me, but if it works for you, no problem
Sent from my Redmi 3 using Tapatalk
haha maybe i am lucky
my computer for some reason just detected the phone the first time i connected to it a few days later.
im having bigger issues now as the flashing took forever after about 12 hours it was still flashing so i unplugged it.
now my phone is bricked i think.
when trying to turn on the phone it is stuck at the mi mi.com logo
it stays there for a few minutes and then vibrates and goes black and starts again.
i can get into fastboot (volume down and power) but cant get into anything else.
You will need to flash a ROM using fastboot.
First install fastboot on your pc: http://www.theandroidsoul.com/how-t...with-drivers-on-windows-quickest-setup-75174/
Second Download a flashable Rom: http://en.miui.com/a-234.html (make sure to choose the right one)
Unzip the rom and navigate to the 'images' folder
Put the phone into Fastboot mode (volume down and power button together until fastboot appears)
Connect the phone to pc with USB
Shift Right click on a blank space in the folder and choose 'open command window here'
run the following commands. one at a time
fastboot devices
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash cache cache.img
fastboot flash userdata userdata.img
fastboot flash system system.img
fastboot reboot
Redmi note4
kosiiik said:
On Windows you usually have to install drivers because windows usually don't recognize device as something connected through com port. This could be done through device manager, install drivers for unknown device, browse for location and they are in drivers directory in miflash directory.
Sent from my Redmi 3 using Tapatalk
Click to expand...
Click to collapse
Hello,
My Redmi Note 4 got Bootlooped,No Recovery No Rom and no way for Charging while pressing and hold the power button,there appeared one second blink of MI Logo.i tried all the ways to flash thro' fast boot mode.but remote partition flashing is no allowed.while tried to flash in edl mode,mi flash didn't detect the Driver.On Seeing device manager the it shows Qualcomm HS-USB Diagnostics 900E and not as Qualcomm HS-USB qdloader 9008.while upading driver it shows the best driver already installed.In my opnion due to Qualcomm HS-USB Diagnostics 900E ,mi flash didn't detect the driver.how can i switched up to Qualcomm HS-USB qdloader 9008.
device not showing in miflash tool in edl mode..
jokerpappu said:
if you want to flash on locked bootloader then you need to be in edl mode not in fastboot mode.to be in edl mode turn off your phone.plug the usb cable to the computer.now get ready to to plug it into the phone but before that be ready to press both volume buttons.this is important step ok.keep your fingers on both volume up and down buttons.now as soon as you plug the usb cable into the phone press both volume buttons.then it will vibrate bt screen will be black.now open mi flash and see there it should show com 10 or com 20 or watever com something like that.then you are ready to flash the rom.after that i hope you know the steps after this.
Click to expand...
Click to collapse
in edl mode device not showing in miflash tool ...
ManishOutlook said:
in edl mode device not showing in miflash tool ...
Click to expand...
Click to collapse
Make sure you have all tye drivers of ur device installed on ur pc and also latest miflash tool and try again
You can try a different usb cable
Hi,
i have the exact same problem. Device doesnt show in Mi Flash. Its the latest version, I installed the drivers and I can see the device in the device manager under Qualcomm HS-USB QDLoader 9008 (COM4). Anybody know a solution?
gottlobzufall said:
Hi,
i have the exact same problem. Device doesnt show in Mi Flash. Its the latest version, I installed the drivers and I can see the device in the device manager under Qualcomm HS-USB QDLoader 9008 (COM4). Anybody know a solution?
Click to expand...
Click to collapse
same problem, mi A2. Device is present in device manager like Qualcomm HS-USB but Mi flash dont show com port...
Max.Payne said:
same problem, mi A2. Device is present in device manager like Qualcomm HS-USB but Mi flash dont show com port...
Click to expand...
Click to collapse
you can use deep flash cable to solve the problem. also you can make the cable yourself. google it and see how to make and use.
rekh said:
you can use deep flash cable to solve the problem. also you can make the cable yourself. google it and see how to make and use.
Click to expand...
Click to collapse
Deepflash cabe not needed, i used tespoint to forse in qualcomm hsxxx mode, device is present in device manager but flasher can't see him. I solved phone on the same way on another computer. First is win7-64, second is win10-64, same program, drivers, flash file... I don't know why... but problem is solved...
How long should it take? Mine is taking very long. And will there be sounds playing of device disconnected and connected again?
Recently, I bought a xiaomi redmi note 3 with the 650 version. I switch to Miui 8 China Fastboot Room from a Global Fastboot Rom, also for unlocking the bootloader. But after I have finished my flashing, it turns out that the Note 3 can't turn on, Stucking on the MI logo for 2 times then turns off again. I tried connecting it to the PC, but the led blinks red. I tried to flash the Miui again but it doesn't show the device. My PC recognized the port as Qualcomm HS-USB Diagnostics 900E, but I can't take it to EDL mode. I tried entering it from the Fastboot mode but still didn't work. Any Help?
*P.S: It also blinks red when I entered the Fastboot Mode
Just checking, but did you use the fastboot edl v2 to enter EDL?
danted7 said:
Recently, I bought a xiaomi redmi note 3 with the 650 version. I switch to Miui 8 China Fastboot Room from a Global Fastboot Rom, also for unlocking the bootloader. But after I have finished my flashing, it turns out that the Note 3 can't turn on, Stucking on the MI logo for 2 times then turns off again. I tried connecting it to the PC, but the led blinks red. I tried to flash the Miui again but it doesn't show the device. My PC recognized the port as Qualcomm HS-USB Diagnostics 900E, but I can't take it to EDL mode. I tried entering it from the Fastboot mode but still didn't work. Any Help?
*P.S: It also blinks red when I entered the Fastboot Mode
Click to expand...
Click to collapse
when i fail to unlock bootloader in official method then i tried miui8 flashboot Rom from mi flash tool with modified emmc_appsboot.mbn file from one of the developer i bricked my Redmi note 3 Qlcmm650
solution:- 1) remove back cover & disconnect the battery around 1 minute reconnect it (recomended one if this not possible for you then try 2nd method)
Or
2)full discharge the battery Then charge it more then 35% (it will also work as diconnecting the battery)
connect the computer &and press volume + & - button together
connect the PC & vol buttons press both are at the same time then you enter the correct EDL mode (same red light but this time correct EDL mode you can flash the rom use official Fastboot rom Dont modify the contents)
if i helped you hit thanks
I was in same situation today: Mobile doesnt do anything else then red-blinking, no edl or fastboot. Pc only saw "Qualcomm HS-USB Diagnostics 900E".
Found the solutions mentioned by Chinmayhegde, but i didnt get the cover off the device and dont want to damage new mobile.
then i found the method "Deep Flash".
its small manipulation of usb-cable: put a small wire on second terminal, put in pc and then pull the wire.
i succeded after second try. then pc sees "Qualcomm HS-USB QDLoader 9008" again and miflash is able to flash the device.
see this tutorial for creating the modded usb cable: http://en.miui.com/thread-310325-1-1.html
Hope it works
if your phone still able to enter fastboot, you can try to use fastboot to edl v2 to enter download mode
if it still not help, most safe & easy mode is using deep flash cable as above post
I have same problem.
Even I try booting fastboot mod but it keeps restarting.
Even fastboot logo comes by just pressing volume down button. So I think power button is stuck. That's make phone restart all the time.
How to overcome this problem?
Thanks
Sent from my SM-G900I using XDA-Developers mobile app
I fix my phone.
Open back cover and undo power cable flex and battery connctor from motherboard and put back after 1 min.
Phone started normal.
thanks
Sent from my SM-G900I using XDA-Developers mobile app
danted7 said:
Recently, I bought a xiaomi redmi note 3 with the 650 version. I switch to Miui 8 China Fastboot Room from a Global Fastboot Rom, also for unlocking the bootloader. But after I have finished my flashing, it turns out that the Note 3 can't turn on, Stucking on the MI logo for 2 times then turns off again. I tried connecting it to the PC, but the led blinks red. I tried to flash the Miui again but it doesn't show the device. My PC recognized the port as Qualcomm HS-USB Diagnostics 900E, but I can't take it to EDL mode. I tried entering it from the Fastboot mode but still didn't work. Any Help?
*P.S: It also blinks red when I entered the Fastboot Mode
Click to expand...
Click to collapse
Try To Remove Your Battery than Use MiFlash Tool To Flash Your Mobile Bro.
Hi,
I start with flashing RM3 kenzo, my brother don´t tell me that he has kenzo, so i flash hennesey via SP-FLASH.
Phone don´t start, just black screen, I wanted to recovery via EDL, but I am confused, Its possible now ?
If I plug phone to PC, device manager is showing loop of:
Mediatek Preloader usb VCOM
USB serial device
There is a way to recovery it ?
THANKS
try use miFlash, if your device is detected (COM?) you may flash the right ROM
ridsa said:
try use miFlash, if your device is detected (COM?) you may flash the right ROM
Click to expand...
Click to collapse
phone is in loop, device manager show MEdiatek usb port, after 1s Mediatek preloader vcom usb, after 1s nothing and again again.
Miflash dont show any device
Can i get to Qualcomm HSUSB QLoader 9008 ?
If it show mediatek preloader ? Is HSUSB QLoader definitely lost?
THANKS
Is it phone still can accessing fastboot mode..?,
you can try press and holding vol down plus power button to force rebooting into fastboot mode..then try reboot into EDL mode from fastboot with this method here,
If success go into EDL mode..you can continue flashing with miflash tool.
No it´s not, I am trying get to EDL mode with EDL cable, but windows say unrecognized drivers and after 2s phone detach, in device manager see nothing.
Red lights blinking when plugged in, shows up as "Qualcomm HS-USB Diagnostics 900E"
Hi,
my Redmi Note 3 (Snapdragon) suddenly stopped working and won't turn on again.
It is from Gearbest and had probably a shop rom installed. I didn't flash any ROM or didn't root it but i checked the "OEM unlock" option in developer options. After that it was bricked (?).
Fastboot doesn't work, it won't turn on (nothing on the screen) and it is recognized in Windows as "Qualcomm HS-USB Diagnostics 900E" when plugged to the pc. Also the LED blinks constantly in red.
Is this already EDL mode?
I tried to use Mi Flash and it didn't recognize the phone. After manually installing "Qualcomm HS-USB QDLoader 9008" in the device manager Mi flash detects it.
When i try to flash a fastboot rom i get the error "sahara read end error with status: 9".
Also tried to open it and short circuit the testpoint pins. In this moment the device is regognized again but nothing changes and it's exactly like described before.
Is the phone dead or can i try anything else?
Thanks
I can't say fire sure but it seems like a hardware problem and that most likely means that it's dead.
You also posted this in the wrong section. This should be in Q&A/Help section. Not in development.
Try charging it for a while. This also happens when the battery reaches an ultra low power state.
If doesn't work, Boot into edl using test point method and flash fastboot rom.
Try this, it worked for me.
First this one
xiaomitips.com/guide/how-to-unbrick-redmi-note-3-snapdragon-best-solution/
If it doesn't work then try this one.
en.miui.com/thread-245347-1-1.html