Hi,
I start with flashing RM3 kenzo, my brother don´t tell me that he has kenzo, so i flash hennesey via SP-FLASH.
Phone don´t start, just black screen, I wanted to recovery via EDL, but I am confused, Its possible now ?
If I plug phone to PC, device manager is showing loop of:
Mediatek Preloader usb VCOM
USB serial device
There is a way to recovery it ?
THANKS
try use miFlash, if your device is detected (COM?) you may flash the right ROM
ridsa said:
try use miFlash, if your device is detected (COM?) you may flash the right ROM
Click to expand...
Click to collapse
phone is in loop, device manager show MEdiatek usb port, after 1s Mediatek preloader vcom usb, after 1s nothing and again again.
Miflash dont show any device
Can i get to Qualcomm HSUSB QLoader 9008 ?
If it show mediatek preloader ? Is HSUSB QLoader definitely lost?
THANKS
Is it phone still can accessing fastboot mode..?,
you can try press and holding vol down plus power button to force rebooting into fastboot mode..then try reboot into EDL mode from fastboot with this method here,
If success go into EDL mode..you can continue flashing with miflash tool.
No it´s not, I am trying get to EDL mode with EDL cable, but windows say unrecognized drivers and after 2s phone detach, in device manager see nothing.
Related
hey
im trying to flash global rom on my phone but i miflash does not seem to detect my phone.
i have tired reinstalling a miflash.
anyone have any ideas what could be the problem?
also could someone send me a link to a clean global rom as i my current rom has been tampered with and the seller has sent me a new rom to flash which i believe also may be tampered with..
Have you unlocked your bootloader yet?
Sent from my Redmi 3 using Tapatalk
GrimEire said:
hey
im trying to flash global rom on my phone but i miflash does not seem to detect my phone.
i have tired reinstalling a miflash.
anyone have any ideas what could be the problem?
also could someone send me a link to a clean global rom as i my current rom has been tampered with and the seller has sent me a new rom to flash which i believe also may be tampered with..
Click to expand...
Click to collapse
if you want to flash on locked bootloader then you need to be in edl mode not in fastboot mode.to be in edl mode turn off your phone.plug the usb cable to the computer.now get ready to to plug it into the phone but before that be ready to press both volume buttons.this is important step ok.keep your fingers on both volume up and down buttons.now as soon as you plug the usb cable into the phone press both volume buttons.then it will vibrate bt screen will be black.now open mi flash and see there it should show com 10 or com 20 or watever com something like that.then you are ready to flash the rom.after that i hope you know the steps after this.
jokerpappu said:
if you want to flash on locked bootloader then you need to be in edl mode not in fastboot mode.to be in edl mode turn off your phone.plug the usb cable to the computer.now get ready to to plug it into the phone but before that be ready to press both volume buttons.this is important step ok.keep your fingers on both volume up and down buttons.now as soon as you plug the usb cable into the phone press both volume buttons.then it will vibrate bt screen will be black.now open mi flash and see there it should show com 10 or com 20 or watever com something like that.then you are ready to flash the rom.after that i hope you know the steps after this.
Click to expand...
Click to collapse
On Windows you usually have to install drivers because windows usually don't recognize device as something connected through com port. This could be done through device manager, install drivers for unknown device, browse for location and they are in drivers directory in miflash directory.
Sent from my Redmi 3 using Tapatalk
kosiiik said:
On Windows you usually have to install drivers because windows usually don't recognize device as something connected through com port. This could be done through device manager, install drivers for unknown device, browse for location and they are in drivers directory in miflash directory.
Sent from my Redmi 3 using Tapatalk
Click to expand...
Click to collapse
I just let windows find the driver and they do.it automatically if u have internet connection ok.why work hard when it can be simple
It has never worked for me, but if it works for you, no problem
Sent from my Redmi 3 using Tapatalk
haha maybe i am lucky
my computer for some reason just detected the phone the first time i connected to it a few days later.
im having bigger issues now as the flashing took forever after about 12 hours it was still flashing so i unplugged it.
now my phone is bricked i think.
when trying to turn on the phone it is stuck at the mi mi.com logo
it stays there for a few minutes and then vibrates and goes black and starts again.
i can get into fastboot (volume down and power) but cant get into anything else.
You will need to flash a ROM using fastboot.
First install fastboot on your pc: http://www.theandroidsoul.com/how-t...with-drivers-on-windows-quickest-setup-75174/
Second Download a flashable Rom: http://en.miui.com/a-234.html (make sure to choose the right one)
Unzip the rom and navigate to the 'images' folder
Put the phone into Fastboot mode (volume down and power button together until fastboot appears)
Connect the phone to pc with USB
Shift Right click on a blank space in the folder and choose 'open command window here'
run the following commands. one at a time
fastboot devices
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash cache cache.img
fastboot flash userdata userdata.img
fastboot flash system system.img
fastboot reboot
Redmi note4
kosiiik said:
On Windows you usually have to install drivers because windows usually don't recognize device as something connected through com port. This could be done through device manager, install drivers for unknown device, browse for location and they are in drivers directory in miflash directory.
Sent from my Redmi 3 using Tapatalk
Click to expand...
Click to collapse
Hello,
My Redmi Note 4 got Bootlooped,No Recovery No Rom and no way for Charging while pressing and hold the power button,there appeared one second blink of MI Logo.i tried all the ways to flash thro' fast boot mode.but remote partition flashing is no allowed.while tried to flash in edl mode,mi flash didn't detect the Driver.On Seeing device manager the it shows Qualcomm HS-USB Diagnostics 900E and not as Qualcomm HS-USB qdloader 9008.while upading driver it shows the best driver already installed.In my opnion due to Qualcomm HS-USB Diagnostics 900E ,mi flash didn't detect the driver.how can i switched up to Qualcomm HS-USB qdloader 9008.
device not showing in miflash tool in edl mode..
jokerpappu said:
if you want to flash on locked bootloader then you need to be in edl mode not in fastboot mode.to be in edl mode turn off your phone.plug the usb cable to the computer.now get ready to to plug it into the phone but before that be ready to press both volume buttons.this is important step ok.keep your fingers on both volume up and down buttons.now as soon as you plug the usb cable into the phone press both volume buttons.then it will vibrate bt screen will be black.now open mi flash and see there it should show com 10 or com 20 or watever com something like that.then you are ready to flash the rom.after that i hope you know the steps after this.
Click to expand...
Click to collapse
in edl mode device not showing in miflash tool ...
ManishOutlook said:
in edl mode device not showing in miflash tool ...
Click to expand...
Click to collapse
Make sure you have all tye drivers of ur device installed on ur pc and also latest miflash tool and try again
You can try a different usb cable
Hi,
i have the exact same problem. Device doesnt show in Mi Flash. Its the latest version, I installed the drivers and I can see the device in the device manager under Qualcomm HS-USB QDLoader 9008 (COM4). Anybody know a solution?
gottlobzufall said:
Hi,
i have the exact same problem. Device doesnt show in Mi Flash. Its the latest version, I installed the drivers and I can see the device in the device manager under Qualcomm HS-USB QDLoader 9008 (COM4). Anybody know a solution?
Click to expand...
Click to collapse
same problem, mi A2. Device is present in device manager like Qualcomm HS-USB but Mi flash dont show com port...
Max.Payne said:
same problem, mi A2. Device is present in device manager like Qualcomm HS-USB but Mi flash dont show com port...
Click to expand...
Click to collapse
you can use deep flash cable to solve the problem. also you can make the cable yourself. google it and see how to make and use.
rekh said:
you can use deep flash cable to solve the problem. also you can make the cable yourself. google it and see how to make and use.
Click to expand...
Click to collapse
Deepflash cabe not needed, i used tespoint to forse in qualcomm hsxxx mode, device is present in device manager but flasher can't see him. I solved phone on the same way on another computer. First is win7-64, second is win10-64, same program, drivers, flash file... I don't know why... but problem is solved...
How long should it take? Mine is taking very long. And will there be sounds playing of device disconnected and connected again?
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
Try again to boot in fastboot mode by pressing vol down + power button for 10 to 20 second if booted into fastboot then release buttons
Try to unlock your device from mi unlock tool
Then it must boot
Try going to Fastboot Mode using Power Button and Vol Down. If you can go to Fastboot, then I'm pretty sure you'll be able to go to EDL Mode. Just look up online how to go to EDL Mode from Fastboot. I think the command to be typed in the cmd window is 'fastboot reboot edl'.
If that works, and you have your Qualcomm drivers installed, you should be able to flash a Fastboot ROM using Mi Flash Tools.
Cheers!
[email protected] said:
Try again to boot in fastboot mode by pressing vol down + power button for 10 to 20 second if booted into fastboot then release buttons
Try to unlock your device from mi unlock tool
Then it must boot
Click to expand...
Click to collapse
I can't seem to get to fastboot or recovery using the button combinations.
It does not even power on, even though i have charged for 8 hours now.
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
manakmishra said:
I can't seem to get to fastboot or recovery using the button combinations.
It does not even power on, even though i have charged for 8 hours now.
Click to expand...
Click to collapse
Open kenzo a.k.a. redmi note 3 disconnect battery
Then connect USB just to mobile not to PC
Then connect battery don't press any button
Connect USB to PC while pressing volume up button
Start mi flash tool click on refresh button see if it detects.
Start flash
manakmishra said:
Before I begin I want to say I'm new to the XDA community, so thank you in advance.
I flashed miui 8.0.1.0 stable rom using miflash. it showed success and so i went forward to reboot my device (still connected to the computer). it displayed the mi logo for about 2s and then went completely black with the red led blinking. i went to device manager to check the port(COM), it showed (still showing) Qualcomm HS-USB Diagnostics 900E. i disconnected the device, the led stopped blinking.
Also i don't have access to either the recovery nor the bootloader.
Here's what i had tried -
1) I tried installing the qualcomm HS-USB QDLoader 9008 drivers, it installed but the device is not detected by miflash.
2) I also tried going to edl mode by reconnecting the battery and usb connection, still no luck.
P.S. I had previously unlocked the bootloader officially.
please help.
Click to expand...
Click to collapse
Simply do this : https://forum.xda-developers.com/redmi-note-3/how-to/guide-reboot-to-edl-mode-fastboot-test-t3398718
Then flash latest global dev rom in Miflash (refresh when phone isn't detected http://en.miui.com/a-234.html
since you can't boot, it might be worth your time to take a look at this.
https://forum.xda-developers.com/redmi-note-3/how-to/guide-how-to-flash-hard-bricked-redmi-t3490055
It's a tutorial to make a 'deep-flash' cable using a micro usb cable that will force your device into fastboot mode, much like samsung's USB jig.
If that works, then you can try following this tutorial :
http://en.miui.com/thread-235865-1-1.html
You can use the link given in post #6 to boot to edl, then flash a stock MIUI ROM using MiFlash.
If all else fails, it might be time to consider taking it to the Mi service centre.
SOLVED
My redmi note 3 pro ( snapdragon ) hard bricked when I use a backup from TWRP.
When I plugged in the usb into my pc , there is a sound and blinking red light appeared.
In Device Manager , it is detected as "QHSUSB_BULK" with a error sign.
(The drivers for this device are not installed. (Code 28) )
I hope can help me :crying:
UPDATE : I updated "QHSUSB_BULK" device to "Qualcomm HS-USB Loader 9008" and my phone is detected in MiFlash according to the guide
"[Tools, Tips & Tutorials] [DEVICE TEAM] Flash (Unbrick) Redmi Note 3(SD) with Locked Bootloader - All ROMS" link : en(dot)miui(dot)com/thread-235865-1-1(dot)html
UPDATE : Before I got to the flash part , Device Manager detected my device as "Unknown USB Device ( Device Descriptor Failed )" instead of "Qualcomm HS-USB Loader 9008"
Tried another 2 perfectly fine USB cable with another PC and still the same.
The red light is still blinking and not detected in MiFlash
vol - and power button press and try to enter in to fastboot...
A Q R I N said:
My redmi note 3 pro ( snapdragon ) hard bricked when I use a backup from TWRP.
When I plugged in the usb into my pc , there is a sound and blinking red light appeared.
In Device Manager , it is detected as "QHSUSB_BULK" with a error sign.
(The drivers for this device are not installed. (Code 28) )
I hope can help me :crying:
Click to expand...
Click to collapse
you phone is in edl mode
try to press and hold power button it will reboot in 10 sec
or flash the fastboot rom
https://www.youtube.com/watch?v=KzNTxRVF0pI skip all thing and strat from flashing rom part in video
and iot not hard brick it soft brick or it enter into edl automatically
android_smater said:
you phone is in edl mode
try to press and hold power button it will reboot in 10 sec
or flash the fastboot rom
link skip all thing and strat from flashing rom part in video
and iot not hard brick it soft brick or it enter into edl automatically
Click to expand...
Click to collapse
UPDATE : I updated "QHSUSB_BULK" device to "Qualcomm HS-USB Loader 9008" and my phone is detected in MiFlash according to the guide
"[Tools, Tips & Tutorials] [DEVICE TEAM] Flash (Unbrick) Redmi Note 3(SD) with Locked Bootloader - All ROMS" link : en(dot)miui(dot)com/thread-235865-1-1(dot)html
UPDATE : Before I got to the flash part , Device Manager detected my device as "Unknown USB Device ( Device Descriptor Failed )" instead of "Qualcomm HS-USB Loader 9008"
Tried another 2 perfectly fine USB cable with another PC and still the same.
The red light is still blinking and not detected in MiFlash
Rajat22 said:
vol - and power button press and try to enter in to fastboot...
Click to expand...
Click to collapse
Nothing happened when I press the vol ( - ) button with power button.
Tried to turn on the phone by pressing the power button only and phone is not booting
A Q R I N said:
UPDATE : I updated "QHSUSB_BULK" device to "Qualcomm HS-USB Loader 9008" and my phone is detected in MiFlash according to the guide
[Tools, Tips & Tutorials] [DEVICE TEAM] Flash (Unbrick) Redmi Note 3(SD) with Locked Bootloader - All ROMS link : en(dot)miui(dot)com/thread-235865-1-1(dot)html
UPDATE : Before I got to the flash part , Device Manager detected my device as "Unknown USB Device ( Device Descriptor Failed )" instead of "Qualcomm HS-USB Loader 9008"
Tried another 2 perfectly fine USB cable with another PC and still the same.
The red light is still blinking
Click to expand...
Click to collapse
Yes it show like that in device manager but in mi flash tool it show like "COM123" like that...
And if you flash the fastboot rom plz cheack thw option inside to save your data
Or try to reboot your phone by pressing power button only for 10 sec
Or vol - and power button to boot into fastboot
android_smater said:
Yes it show like that in device manager but in mi flash tool it show like "COM123" like that...
And if you flash the fastboot rom plz cheack thw option inside to save your data
Or try to reboot your phone by pressing power button only for 10 sec
Or vol - and power button to boot into fastboot
Click to expand...
Click to collapse
Finally! my phone detected in MiFlash also in Device Manager as "Qualcomm HS-USB QDLoader 9008"
So the fastboot for kenzo is called "kenzo_global_images_V8.2.4.0.MHOMIDL_20170522.0000.00_6.0_global_0cc0f93a7c.tgz" from en(dot)miui(dot)com/a-234(dot)html
Am I right?
A Q R I N said:
So the fastboot for kenzo is called "kenzo_global_images_V8.2.4.0.MHOMIDL_20170522.0000.00_6.0_global_0cc0f93a7c.tgz" from en(dot)miui(dot)com/a-234(dot)html
Am I right?
Click to expand...
Click to collapse
Yes
---------- Post added at 04:09 AM ---------- Previous post was at 03:51 AM ----------
http://bigota.d.miui.com/V8.0.1.0.L...DG_20160805.0000.29_5.1_global_5e65360aff.tgz
Direct link
SOLVED Thanks guys !!!
A Q R I N said:
Finally! my phone detected in MiFlash also in Device Manager as "Qualcomm HS-USB QDLoader 9008"
Click to expand...
Click to collapse
Please can you provide me the link to download the driver!
I accidentally flashed Redmi note 3 firmware into Redmi note 4. Now only red light is blinking. No fastboot also. Computer showing in ports Qualcomm hs usb qdloader 9008 (com3). Please help me flash full fastboot rom
if your computer detects your device as qdloader , that means it is in EDL mode, in this mode , you should be able to flash fastboot roms using miflash , you should read this thread first, http://en.miui.com/thread-565784-1-1.html . although the thread writes about flashing in fastboot mode, but it shouldn't differ alot from flashing in EDL mode, just follow the B part of the guide in the link, MIFlash should be able to detect your device and list it down as COM(number) .
As for the driver part, you shouldn't need to update anything if MIFlash can detect your device , as your computer already correctly detects it as QDLoader
chun_9876 said:
if your computer detects your device as qdloader , that means it is in EDL mode, in this mode , you should be able to flash fastboot roms using miflash , you should read this thread first, http://en.miui.com/thread-565784-1-1.html . although the thread writes about flashing in fastboot mode, but it shouldn't differ alot from flashing in EDL mode, just follow the B part of the guide in the link, MIFlash should be able to detect your device and list it down as COM(number) .
As for the driver part, you shouldn't need to update anything if MIFlash can detect your device , as your computer already correctly detects it as QDLoader
Click to expand...
Click to collapse
Thankyou for your valuable reply. Miflash detecting device. But error in flash. Then removed back cover and removed battery connection also. Then Miflash flashed the rom successfully
My Redmi Note 4 is hard bricked...:crying:
I unlocked the bootloader the official way and was trying to flash lineageos on it. I failed :crying:
I cant go into Fastboot mode or Recovery. The Phone wont turn on. I get the Red LED light, when i connect it with the computer.
I bought a Deep Flash Cable and connected my phone with unplugged battery. In device manager under ports i got
qualcomm hs-usb diagnostics 900e. But under MIFlash tool there was no com port. So i changed the driver of the
qualcomm hs-usb diagnostics 900e to qualcomm hs-usb qdloader 9008 (com10) and i got com10 in miflash. If i try to flash the fastboot rom (stable) i get this error: sahara read end error eith status:9. :crying:
I hope someone can help me?
Ninman20
Ninman20 said:
My Redmi Note 4 is hard bricked...:crying:
I unlocked the bootloader the official way and was trying to flash lineageos on it. I failed :crying:
I cant go into Fastboot mode or Recovery. The Phone wont turn on. I get the Red LED light, when i connect it with the computer.
I bought a Deep Flash Cable and connected my phone with unplugged battery. In device manager under ports i got
qualcomm hs-usb diagnostics 900e. But under MIFlash tool there was no com port. So i changed the driver of the
qualcomm hs-usb diagnostics 900e to qualcomm hs-usb qdloader 9008 (com10) and i got com10 in miflash. If i try to flash the fastboot rom (stable) i get this error: sahara read end error eith status:9. :crying:
I hope someone can help me?
Ninman20
Click to expand...
Click to collapse
https://www.google.com/amp/s/forum....-fix-totally-dead-redmi-note-4-t3746465/page1
Hope it helps you
Sent from my mido using XDA Labs
Ninman20 said:
My Redmi Note 4 is hard bricked...:crying:
I unlocked the bootloader the official way and was trying to flash lineageos on it. I failed :crying:
I cant go into Fastboot mode or Recovery. The Phone wont turn on. I get the Red LED light, when i connect it with the computer.
I bought a Deep Flash Cable and connected my phone with unplugged battery. In device manager under ports i got
qualcomm hs-usb diagnostics 900e. But under MIFlash tool there was no com port. So i changed the driver of the
qualcomm hs-usb diagnostics 900e to qualcomm hs-usb qdloader 9008 (com10) and i got com10 in miflash. If i try to flash the fastboot rom (stable) i get this error: sahara read end error eith status:9. :crying:
I hope someone can help me?
Ninman20
Click to expand...
Click to collapse
1. Remove the back panel then the battery connector. Keep it in that way for a while like a minute
2. Then short either the 'most effective points' or 'less effective points' following this thread . While keeping them short, connect the USB cable to the Computer, it will enter into 'download' mode suitable for miFlash/QFIL