Can't get to CWM - Barnes & Noble Nook Tablet

Hello, I have a Nook Tablet Acclaim running CM 10. I haven't made any changes to the tablet for months, maybe years. Yesterday it stopped working.
- When I turn it on, I get the first image with "N" in the center and the Adobe copyright at bottom.
- I do not get the second image where pressing "N" takes me to the CWM boot menu.
- Pressing N does not do anything.
- If it is not plugged in, the tablet shuts off.
- If it is plugged in, the tablet shuts off, then starts up again, then shuts off, in an infinite loop.
- It does not matter if I'm plugged in to the charger or my PC.
Other notes
- I let the battery run down yesterday on purpose, because I thought somehow that might make it different.
- When this first started, I briefly saw the regular boot sequence, but it didn't make it all the way through. The it went to this sequence.
Any ideas? It feels like a hardware problem. If it's a battery problem, I could get a new one. But if that's not the problem, it would be a waste of money.
Any help would be appreciated.

johnsonbx said:
Hello, I have a Nook Tablet Acclaim running CM 10. I haven't made any changes to the tablet for months, maybe years. Yesterday it stopped working.
- When I turn it on, I get the first image with "N" in the center and the Adobe copyright at bottom.
- I do not get the second image where pressing "N" takes me to the CWM boot menu.
- Pressing N does not do anything.
- If it is not plugged in, the tablet shuts off.
- If it is plugged in, the tablet shuts off, then starts up again, then shuts off, in an infinite loop.
- It does not matter if I'm plugged in to the charger or my PC.
Other notes
- I let the battery run down yesterday on purpose, because I thought somehow that might make it different.
- When this first started, I briefly saw the regular boot sequence, but it didn't make it all the way through. The it went to this sequence.
Any ideas? It feels like a hardware problem. If it's a battery problem, I could get a new one. But if that's not the problem, it would be a waste of money.
Any help would be appreciated.
Click to expand...
Click to collapse
So are you trying to boot to SD recovery?

nmyshkin said:
So are you trying to boot to SD recovery?
Click to expand...
Click to collapse
No, internal.

johnsonbx said:
No, internal.
Click to expand...
Click to collapse
But can you boot from the SD card? Maybe the boot sequence has been corrupted. If you can boot from the card you used to write CM 10 perhaps you can restore a backup that might correct the issue. Failing that you could try flashing CM 11 or 12 or 13.

Related

Touch Pro abruptly stopped working; won't boot.

So here's a peculiar incident:
I have a CDMA TP with a stock ROM and a few basic apps I gathered from these forums and others. I've had it for less than a week.
Tonite, I went to check my text messages. Suddenly, the screen went black and the phone stopped responding. After pressing the power button and fiddling with the keys, I pulled out the stylus and did a soft reset. No response. Confused by this, I tried again, but still nothing. I removed the battery, and turned the phone back on. It froze at the "Touch Pro" screen with the rom/radio/etc info at the bottom. After repeating this a few times I decided to do a hard reset. So, I turn the device on and perform the hard reset. By this point the TP is only turning on SOME TIMES, and I have to take the battery out and put it back in often just to get it to start successfully. So, I finally get the device to boot up and it starts to configure WinMo. Suddenly, while configuring, it freezes. Now I try to turn it back on, and nothing happens.
Basically the device is stuck like this, shifting between not turning on at all and turning on but freezing at the "Touch Pro" screen.
So, my question is, what the heck is going on here? Has anyone else had this problem, or does this sound familiar to anyone? Any help would be greatly, greatly appreciated.
p.s. Yes, the battery is fully charged.
kameisama said:
So here's a peculiar incident:
I have a CDMA TP with a stock ROM and a few basic apps I gathered from these forums and others. I've had it for less than a week.
Tonite, I went to check my text messages. Suddenly, the screen went black and the phone stopped responding. After pressing the power button and fiddling with the keys, I pulled out the stylus and did a soft reset. No response. Confused by this, I tried again, but still nothing. I removed the battery, and turned the phone back on. It froze at the "Touch Pro" screen with the rom/radio/etc info at the bottom. After repeating this a few times I decided to do a hard reset. So, I turn the device on and perform the hard reset. By this point the TP is only turning on SOME TIMES, and I have to take the battery out and put it back in often just to get it to start successfully. So, I finally get the device to boot up and it starts to configure WinMo. Suddenly, while configuring, it freezes. Now I try to turn it back on, and nothing happens.
Basically the device is stuck like this, shifting between not turning on at all and turning on but freezing at the "Touch Pro" screen.
So, my question is, what the heck is going on here? Has anyone else had this problem, or does this sound familiar to anyone? Any help would be greatly, greatly appreciated.
p.s. Yes, the battery is fully charged.
Click to expand...
Click to collapse
Time to take it in and get a new one.....
Same problem here phone started b not coming out of lock mode. Backlight is on but no display on screen (if i tilt the screen left and right i can see light coming from behind) did about 6 hard resets and still same problem. also power button works whenever it wants to. this phone sucks @ss, i want my mogul back. on a second note my replacement will be here on wednesday.
Touch Pro stock rom purchased back in nov when it came out
yeah, i've had the same problem, i found if i hit my phone on the back or side and then batter pull and hit the soft reset while off, not the power button to turn it back on, it comes back on with color on the screen not just blank black screen with backlight, this works mostly every time, but when it doesn't, i just hold the power button down and do battery pull and hit the power button and it works, its like its got a combo of things you have to do before it works.. weird
Boot Up
I have also had similar problems. I for some reason sometimes have to remove my SD card and boot up without it for some reason. Not all the time, but every once in a blue moon. Not too sure how that affects anything, but you may try that too.
well i started a thread here ***help*** because i kinda have the same problem.
i downloaded some cabs, nothing fancy but i had some problems with a theme i downloaded. when i went to deleted i couldnt..... to make a story short, i took it to the sprint store where they tried to do a master reset/ hard reset and it wont take it. it wont do a thing... they say some important files are missing...
the phone works but not the way it should... the time on the home screen wont show up. and some other small things...
dont know how this happened but i would like to know... im worried about new programs to the phone now. ( getting a new one)
still want to see if i can fix this one.
Mayonesa said:
well i started a thread here ***help*** because i kinda have the same problem.
i downloaded some cabs, nothing fancy but i had some problems with a theme i downloaded. when i went to deleted i couldnt..... to make a story short, i took it to the sprint store where they tried to do a master reset/ hard reset and it wont take it. it wont do a thing... they say some important files are missing...
the phone works but not the way it should... the time on the home screen wont show up. and some other small things...
dont know how this happened but i would like to know... im worried about new programs to the phone now. ( getting a new one)
still want to see if i can fix this one.
Click to expand...
Click to collapse
Have you tried re flashing the ROM?
it wasnt HTC's fault for your phone's not booting...thats what happens when u try to mess with the hardware too much and you dont know what your doing
Would you want to sell???
Reboot Brick HTC process
****DOn't take battery out after hard boot***
1.just watch videohttp://www.youtube.com/watch?v=sk56olMkCtU and do what they do but dont take battery out. LEAVE phone STUCK on BOOT screen. Nothign else will move or work but you want phone just like that.
2. connect usb cable to active sync. (this may not link up but leave usb connected anyhow) Do not delete phone profile.
3.use rom like Download MightyROM6_Herman.exe avail at: http://www.lilrico.com/Mighty/mightyromblog/?p=454
4 although active sync is still attatched but may not be connecting. It will connect thru usb anyway when you run the rom software. http://www.youtube.com/watch?v=fV2I2WAFkg4&NR=1
This worked and kept phone from cutting on and off. and restored ROM. don't know about original htc boot. but your phone will work under this rom for now and you can go from there.
hey thanks plain ole dumb, it works now.
man I thought it was over.
thanks again

[Q] Samsung Galaxy S Showcase Problem.

So I've run into quite an annoying problem- I can't install applications from the market. Last night, I had my phone plugged into my computer and I don't THINK I had the SD mounted, but I've been wrong before. Anyways, I went to disconnect it and instead of dismounting then unplugging, I just unplugged. Since then, if I try to download something, the notification bar will show that the app is downloading, for a second, then it just disappears. My phone is rooted, no custom rom though, and I'm not running Apps2SD. Also, I'm running Ubuntu 10.10 x64 on my computer.
This has happened once before, and I had to tinker with popping my SD card out and rebooting the phone a few different ways before it finally started acting right again. I'm looking for help because 1) I can't remember exactly how I did it and 2) I figured I might as well try to find out if anyone here knows what I could do to fix it.
Thanks in advance.
Galaxy S Showcase stuck at very first screens
Afternoon guys, I did some browsing and searching and cannot seem to find a way to fix this, so here goes:
Samsung Galaxy S i500, Showcase with Cellular South.
It is rooted, with the original ROM/Kernel.
Yesterday, I was attempting to follow the guide on getting ClockWorkMod on it (http://forum.xda-developers.com/showthread.php?t=860250) and when I finally got the final command to work, the phone rebooted, and has since been doing VERY little.
Power Button = SAMSUNG... No vibrate, No change.
Vol Up/Down + Power = SAMSUNG... No vibrate, word flashes, release power (steps to enter recovery or download), SAMSUNG screen remains. Still no vibrate or anything.
Plug in = Grey battery with "loading" circle with no animation of any kind. It is charging though.
Plug in + Vol for recovery/download mode = still just grey Battery not moving.
In all attempts, I have left it trying for anywhere between 30 mins to 4 hours... I cannot get to anything but those 3 results. (samsung, samsung w/ 1 flash, and grey battery).
If I can get it into Download, I can Odin it, or recovery to reset to factory... but I need to get to one. Any and all help is appreciated.
~*~*~Artilleur~*~*~
Download Mode
I had similar situation. Could not get past samsung screen. No splash screen.
Download mode. Pull battery, Plug in USB, hold Vol-. Little guy with shovel.
As for getting back to running. Good luck. I got new warrantied phone couldn't figure out how to fix after soft brick.

[Q] Suddenly, OS doesnt load

SGS2 I9100 with Ressurection Remix ICS_v2.4_AOKP-B39-4.0.4
Device was working fine, battery was low (<5%) so i connected my charger; went to sleep, woke up and tried to turn display on - couldn't ... i thought that maybe phone was battery dead when i connected it so i long-press the power button to start it up but nothing was happening.
Disconnected the charger, took out the battery, waited 20s then put it back, connected charger and tried to power on => sgs2 splash screen .... .... ... showing desktop screen w/o icons and after 5-10s device shows "Shutting down" vibrates and shuts down.
Rebooted into CWM recovery, reinstalled ROM => no change
Rebooted into CWM, wipe data/factory reset => no change
Any ideeas what is going on? is the battery malfunctioning?
Try a new battery in the first instance. If it still happens once you've done that then we can look at other causes. Also, if you feel so inclined, do a clean install of stock & see if that fixes the issue to rule out something in your current setup (rom/kernel/etc) causing the problem.
thanks, been thinking the same about trying another battery but that is something i cannot do today
MistahBungle said:
Try a new battery in the first instance. If it still happens once you've done that then we can look at other causes. Also, if you feel so inclined, do a clean install of stock & see if that fixes the issue to rule out something in your current setup (rom/kernel/etc) causing the problem.
Click to expand...
Click to collapse
tried another battery, same.
flashed a stock, os load doesnt pass "S" screen
also i recharged battery on another phone and when i use it in mine, it gets drained quickly
guess the problem is the "power supply"

[HELP] Sony Tablet S - Not Getting Past Boot Animation

G'day guys,
Having some issues with my Tablet. I had been using it for basic web\email and had zero issues. I was playing a game (which had been played, on and off, for 3+ months) on the device when it froze.
Pressing 3 software buttons (home, back, switch) did not respond. The Volume rocker didn't adjust volume. Pressing Power didn't turn off screen. So I held down Power for 3 seconds. Nothing. Held it down for 5 seconds. Nothing! ... Held it down for 10 seconds and it switched off.
I left it for 2-3 minutes and then turned the tablet on. Just gets stuck on the Sony animated boot screen. Nothing more!
OS 3.0 upgraded to OS 4.0.3 direct from built-in Sony upgrade. Zero issues for months until now.
Stock ROM. Not rooted.
I was hoping to get the data off the internal storage however if it is not possible... then maybe I just need to move on and start fresh! :\
I have a suspicion there is a corruption with something like /cache or something else really simple.
Would be great if anyone is aware of a simple fix without losing data, or a full-proof way to resolve it by doing anything..... Just need a reliable solution...
HELLLLLP!
THANK YOU!
NOTE: I can bypass the boot animation and access the recovery interface.
Cheers guys!
Following the instructions here a few days ago http://www.howtogeek.com/125375/how...kup-without-rooting-or-unlocking-your-device/ (http://developer.android.com/tools/sdk/tools-notes.html and http://developer.android.com/sdk/index.html#win-bundle) I downloaded and installed the bundle as per instructions.
When Sony Tablet S is connected, nothing is displayed. Although, granted, it took a lot of fiddling to get the Samsung to show up (damn USB / Sync / xxx modes for USB connectivity.
Code:
C:\Users\Flip\AppData\Local\Android\android-sdk\platform-tools>adb devices
List of devices attached
My Samsung, which I plan to backup and then root via KingRoot:
Code:
C:\Users\Flip\AppData\Local\Android\android-sdk\platform-tools>adb devices
List of devices attached
304xxxxxxxxxx4AE device

Fusion5_108 / Allwinner A83T based tablet, stuck in boot loop / No Command

I got a cheap Fusion5_108 tab off ebay working but with a cracked "screen"
i've ordered a new digitizer... atm it's totally unresponding to touch, but will work with a mouse / keyboard in the usb A socket on the tab.
So i was playing with it, i plan to use it for one specific task... part of a train driving control desk, the tablets will be the displays found in German trains... i.e. the 'MFA' thats speedo gauges and lights on one tab, electronic timetable on another tablet, the engine dignostic data on another tab, brake pressure gauges on another etc... i already have a lenovo A6700-f that i replaced the digitizer on and did the same things to, and it still works fine.
I loaded the 'TS_MFD' app that works with the train sim via tcp, got it all working fine.
Then i decided i didnt like the google search bar along the top of the home screen, and found out online that by disabeling google services app, it'd get rid of it... so i did that, the search bar went.. but left a shadow box where it used to be... so i thought i'd reboot the tablet and see if that got rid of it.
Held power button in till i got the shutdown / re-boot options, chose re-boot.
Aaaannnd... now it's stuck in a boot loop. all it does it begin to start up... the Fusion5 logo comes up, then it goes "android is starting" 'optimizing apps, 1, 2, 3 of 3...'
Then black screen with android in middle, and that screen goes brighter and dimmer... then eventually it'll reset, and show the "android is starting, optimizing apps' thing over and over.... once it froze on the optimizing apps screen, the circle that goes round froze. but usually it's just loops... left it overnight and still doing it this monring.
If i shut it down by holding power for 10 seconds or so, and hold any volume button and power, it'll start the recovery thing... BUT all i get is the dead android and "No Command'
And no combinations of pressing the power and volume buttons will do anymore... even tried with a mouse and a keyboard... best i could get is a re-boot pressing CTRL - ALT - DELETE on the keyboard.
There seems no way to get this thing to show the recovery options... when i did this on the lenovo tab, it went straight to the 'select option with volume buttons' thing i'm expecting.
Obviousely there's no wany to get this tablet into USB debugging mode, trying the thing where you hold volume button, plug usb cable in, press power 10 times, it sometimes shows up as a usb media devise, sometimes a NDIS internet sharing devise. but they go when it boot loops.
I even tried de-soldering the battery and leaving it for 20 minutes, but upon re-soldering the battery onto the mainboard, it does the same boot loop thing.
I've read i could use Phoenix card writer to make an SD card with the firmware on it, and start the tablet up with that sd card in the slot and it'll load from it.... but where do i find the firmware? the allwinner site doesnt seem to have a firmware... that i can find for the A83T processors.
This is all i know about this devise:
Allwinner
Fusion5_108
1.0
002001014108aa62de01
A83t processor (confirmed by looking inside it)
not mine.. but same model:
ro.product.firmware=v6.0rc4_20161114
ro.fota.version=Fusion5_108_16_OS60_UK_20170310_V2F
ro.inet.model.name=N1061L14BC
Any suggestions?
Got it fixed,
Been emailing the fusion5 people, started that via their store... just google fusion5 store.
And they spend a while figuring out which tablet i have, sent an .img file... first one was for the wrong devise..... never than the one i have... but the 2nd try they got me the right firmware,
Loaded it to a micro SD card using phoenic card, popped the sd card in the tablet, started it up and it loaded the firmware, took the sd card out, and it rebooted and started up fine,
Only thing is it's android 5, and the tablet used to be running android 6... so now i'm looking at how to upgrade to marshmallow, as there are some apps i used that wont run on older than android 6.
Rom needed
Hi mate, do you mind sharing the ROM for the fusion5 108 ?
Thanks
re: Fusion5 Rom
Hi there. I know this thread is a couple of years old, but I haven't been able to find the ROM for this tablet anywhere else, so I wanted to see if you (or anyone reading this) wouldn't mind sharing it. Thanks!
Buying copy of img file
Gazz said:
Got it fixed,
Been emailing the fusion5 people, started that via their store... just google fusion5 store.
And they spend a while figuring out which tablet i have, sent an .img file... first one was for the wrong devise..... never than the one i have... but the 2nd try they got me the right firmware,
Loaded it to a micro SD card using phoenic card, popped the sd card in the tablet, started it up and it loaded the firmware, took the sd card out, and it rebooted and started up fine,
Only thing is it's android 5, and the tablet used to be running android 6... so now i'm looking at how to upgrade to marshmallow, as there are some apps i used that wont run on older than android 6.
Click to expand...
Click to collapse
Hi any chance of buying a copy of the img file. My tablet has just gone to 'No Command' screen and I cannot get it to load.
Thanks.
Andy
---------- Post added at 06:23 PM ---------- Previous post was at 06:18 PM ----------
AndrewRobert said:
Hi any chance of buying a copy of the img file. My tablet has just gone to 'No Command' screen and I cannot get it to load.
Thanks.
Andy
Click to expand...
Click to collapse
The company say the tablet is obsolete and it will not support it any longer
Andy

Categories

Resources