please kindly help me, I hard bricked my infinix hot note 16+1 while trying to flash recovery using sp flash tool.
its been dead for about a week now, i charged it, removed the battery clip and replaced it, tried flashing preloader.bin, but remains dead.
i get dram 4032 error while trying to flash a custom rom i downloaded online. tried formatting it too, but i still get the same error. now im left with no phone. kindly help.
NB, i have uninstall and re install vcom drivers, re extract sp flash tool version 5/version 3 all to no avail.
Related
Hi all,
please help me out because I'm desperate.
Yesterday I received a THL W8 mobile phone and I flashed it with the ROM reported on this thread.
Once done, my SD card wasn't recognized by the phone, so I decided to flash the same ROM again.
Unluckily, my bad, I didn't uncheck the PreLoader tick and as result now the phone doesn't boot at all.
The PC recognizes it and the drivers are ok, but when I try to flash a ROM, any ROM, I get different errors.
With SP Flash Tools version "SP_Flash_Tool_v3.1304.0.119" the bottom bar fills red fully (100%) but after about 40 seconds it gives me the following error:
S_FT_ENABLE_DRAM_FAIL (4032)
With the SP Flash tools version "AntiBrick_Flash_Tool_v3.1224.0.sn85" 3 seconds after the bottom bar gets filled in red, the following error is returned:
SP FLASH TOOL ERROR: (8200)
[Platform Error] The load and target are inconsistent!
I've also tried to flash the stock ROM but with the same bad results. More, I tried to do a reset with both the aforementioned Flash tools versions with success, but after that whenever I try to flash the phone with any ROM, I get the same errors as before.
Since the PC recognizes the phone I'm kinda sure it can be restored, but apart what I tried already, I'm out of ideas.
Any help is welcome
Thank you guys
Cheers
Heide
really? no one really answered the poor guy, the phone ended up bricked for good after all
Hi, I was trying to use Flash tool and Don't know what happend but My Phone is completely DEAD right now even power button is also not working no screen is there (just blank phone).
I am having UMI X2 2GB rom, 32 gb internal memory, 1.5 GHZ (MT6589T) Model.
I tried to use SP Flash tool to recover my phone. Firstly I tried to format the phone, After that I tried to run the correct scatter file for MT6589 (from one of the ROM Posted under UMI-X2).
Drivers for the SP Flash tool is loaded correctly (into my Windows 8 Pc). I was previosly getting error as follow : SP FLASH TOOL ERROR: (8200)
[Platform Error] The load and target are inconsistent!
Now, after searching a lot I found that its something wrong with SP Flash tool version.
So I downloaded SP Flash Tool V3.1304.O.sn119 version. After that I am trying to "Download" the rom (with the correct scatter file for my ROM). but its only showing me RED Bar (with 100%) and after that it does nothing. Its neither showing me any error nor its continuing the process.
I am in serious problem here. Please help me out.
Thanks in advance!
- Umang
umang_nine said:
Now, after searching a lot I found that its something wrong with SP Flash tool version.
So I downloaded SP Flash Tool V3.1304.O.sn119 version. After that I am trying to "Download" the rom (with the correct scatter file for my ROM). but its only showing me RED Bar (with 100%) and after that it does nothing. Its neither showing me any error nor its continuing the process.
I am in serious problem here. Please help me out.
Click to expand...
Click to collapse
Try this version of :
SP Flash Tool
October Official Rom
USB Drivers (if needed)
Works for me.
Necro thread...
I have the same issue.
A couple of days ago the phone just started turning off / locking up when off, and having great difficulty tuning on... i.e. pulling out the battery for a minute or a few times.
Now the phone won't turn on at all. They only sign of life is the charging animation when you plug it in.
Prior to all this, there appeared a window in Chinese with some options. my GF (who's phone it is) just pressed something, no idea what. But she said something about 'drawing on the screen'??? sound like something locked up and the previous frame wasn't deleted from the frame buffer before redrawing the new one... I have no idea.
Anyway, I tried going into recovery to see if there was anything I could do there, unfortunately everything was in Chinese, so not much help. for some reason now, the recovery isn't even working.
Now I can connect to the phone via SPflash, but I get the above response: '[Platform Error] The load and target are inconsistent!'
Some other ROMs I tried give me this response:
'The load to be downloaded is for MT6589;
The target platform is MT6582_S00'
Which is quite suspicious.
Any ideas?
Thanks
hisense HS-U980 bricked....
hi,i have the smartphone hisense hs-u980 with mt6589 or mt6589t, i dont understand.... so, i briched with sp.flash tool and now is ompletly dead,,, can i have ur help-sipport please?
thank u very much
Hs-u980 complete dead/bricked
carretto76 said:
hi,i have the smartphone hisense hs-u980 with mt6589 or mt6589t, i dont understand.... so, i briched with sp.flash tool and now is ompletly dead,,, can i have ur help-sipport please?
thank u very much
Click to expand...
Click to collapse
i have ur same phone and i have ur same problem,my pkone is dead later flash any wrong miui rom from cwm recovery and now is dead,i dont have any idea where is original firmware for sp.flash tool or other how piranha box,please,anyone can please me??? THANK U for read!!!!
I have the same Problem. So frustrating men. If anyone finds a solucion please email me [email protected] ...
SP FLASH TOOL ERROR: (8200)
As i connect my phone it disconnects after 2 seconds..
Please give me a site to download scatter file for my micromax a 310
So i tried to install ZGPAX S8 rom via sp flash tool, now i think it is bricked totally. I got IconBit 100 Callisto, Eu.
So, watch doesnt start, PC says its unknown device, trying to do anything in SP Flash tool ends in error 4032.
Can it be helped?
Ziembski said:
So i tried to install ZGPAX S8 rom via sp flash tool, now i think it is bricked totally. I got IconBit 100 Callisto, Eu.
So, watch doesnt start, PC says its unknown device, trying to do anything in SP Flash tool ends in error 4032.
Can it be helped?
Click to expand...
Click to collapse
No Bricked
Follow this:
open your smartwatch
remove battery
reinsert battery
flash Callisto 100 STOCK rom
Well, tried it like ten times.
Now SP Flash Tools gets stuck at 100% when flashing anything.
Trying another STOCK rom...
YIS, found good rom, now its working propetly.
Hello,
I have an Lenovo S960, which is an MTK 6589 Device.
Coming to the Point, Yesterday I my little sis didn't know what did, Phone Got Soft Brick.
Ohk, I tried to Re-Flash the ROM with SP Flash Tool Ver 3.1xx But somehow it got stuck on 18% and got error of brom error s_da_sdmmc_write_failed (3149).
When i tried to Format+All Download with the latest version of SP Flash Tool, it keep saying "Unrecognized Rom Detected".
Now, I tried Flashing the same ROM with different Versions of SP Flash Tool, and Got several Errors. amongst which one error really horrified me, i didn't remember exactly what was that, but it was something like No Valid partition Management Table.
After some research i found that the rom can be Flashed via MTK DROID TOOLS Onlyy, but for which i need Back Up of the Rom, which i didn't have.
The point is:
1) Is there any way to Flash the Rom with SP Flashtool bypassing these errors.
2) I would be very thank ful if any one can provide me the Back Up Rom for Lenovo Vibe X S960.
One more thing, This is my Fiance's Phone, and she's about to kill me if i didn't Give her phone on Sunday..
Please Help me..
Hi Guys
i have bricked my Vodafone VF685/ Alcatel Pop D1/ Huawei U1860 or whatever make this is (quite confusing) with SP Flash tool MT6572.
I tried to flash CWM recovery (successfully rooted with KingRoot) with the Scatter file compatible with the SP Tool version. All went well, bur my phone didnt want to go past the start up logo. So i tried flashing it again, and now it doesnt want to switch on nor charge, cant boot into recovery. Just a dead phone with a black screen. My pc doesnt pick up my phone via usb and i get error code 4004, i did some searching on how to fix the error code but im still stuck in a rut...
Any advice on how to fix this and please any advice on how to tell which recovery and scatter and firmware is for this phone?
Model: V685-1
SVN: 120HJG1
MANF: TCT MOBILE LTD
CU REF: V685-2AVDZA1
Thank you in advance, i really appreciate your help and advice.
Johan
Well, this is quite dissappointing... Not a yes or a no... Nothing....