My moto e2 otus 1506 model is bricked. I will list things that I did.
1. Unlocked bootloader, installed moto drivers in PC.
2. Downloaded twrp
3. Flashed twrp.
4. Downloaded RR ROM based on cm13.
5. Downloaded gapps 6.0.
6. Downloaded blive kernel.
7. Copied to memory card, mounted it.
8. Twrp- erase all, format,clear cache- flash- ROM, gapps, kernel- clear cache-Reboot.
9. Phone works but lags a lot. Used it for few weeks. Tried kernel flash first and last, but sometimes it won't boot at all. At best ROM+gapps worked without issues, but phone lagged.
10. I thought it is coz of RR ROM and cm13 should be used. Downloaded cm13 snapshot.
11. Twrp flash fails, says, invalid zip file. Tried other cm13 files, same error.:crying:
12. Surprised I try RR again. It works.
13. After using the slow phone, I find time and after reading XDA, I decide to revert back to stock and try cm13 first.
14. Downloaded firmware files, 2 files, just in case 1 fails.
15. Tried fastboot commands. All well but it won't boot neither into recovery.
16. Tried twrp flash. Failed. Tried several times and it worked once.
17. Instead of living with RR ROM, I tried again with stock flash. Failed and twrp shows invalid errors and reboots.:crying::cyclops:
18. Left it for few weeks, battery drained, tried to charge by several methods, wall charger, PC charging , cmd script to reboot and charge, all failed. In fasboot mode it shows connected, battery low and charging, but does not charge.
Currently, all it shows is fastboot mode if lucky or else a white screen with 0 battery. How to bring it back to life?
Options and steps please. Hope to get help soon . thank you.
Somebody please help me....
If you are able to boot into the fast boot, try restoring to stock firmware. http://forum.xda-developers.com/moto-e-2015/general/guide-restore-moto-e-2015-stock-firmware-t3044936
meVikki said:
If you are able to boot into the fast boot, try restoring to stock firmware. http://forum.xda-developers.com/moto-e-2015/general/guide-restore-moto-e-2015-stock-firmware-t3044936
Click to expand...
Click to collapse
plz read its current status. its battery is empty and not charging. neither in wall or pc. i read something like, if it goes beyond certain voltage its very difficult to bring it back to life.
if mounted in wall charger it shows a constant white led and nothing else.
legendracer said:
if mounted in wall charger it shows a constant white led and nothing else.
Click to expand...
Click to collapse
If is showing the led. It should charge. If it isn't then you need a screwset to open your phone and charge the battery externally. Please check the phone on a dark room that is it really dead or phone screen is black.
Sent from my Moto E using Tapatalk
meVikki said:
If is showing the led. It should charge. If it isn't then you need a screwset to open your phone and charge the battery externally. Please check the phone on a dark room that is it really dead or phone screen is black.
Sent from my Moto E using Tapatalk
Click to expand...
Click to collapse
I don't have tools to open and charge. Screen is dead. But wen connected to PC it goes to fastboot mode. But no flash possible as it shows low battery error during flash. Thinking o going to svc.
plug your charger to wall then hold you phone and press and hold down volume button . next is connect your charger to the phone while pressing volume button. then you are on fastboot.?? now wait atleast 1hour .. your phone is charging
Bro calm down.....first plug i n with your charger for one whole night.....if it doesn't starts then ...try pressing power button and volume down while plugged in...
---------- Post added at 10:52 AM ---------- Previous post was at 10:51 AM ----------
If it works reply me ...I will tell u what to do next
---------- Post added at 10:52 AM ---------- Previous post was at 10:52 AM ----------
Keep patience... Everything will go smoothly
my (otus) xt-1506 also broken , today .
was rooted 4months ago,
after latest security patch (9mb file size) phone gone corrupt and flashed stock firmware from here -(add ww.)firmware.center/firmware/Motorola/Moto%20E%20%282nd%20gen-2015%29/Stock/XT1506/
flash was successful
and after then checked for update and found a system update from 5.0.1 to 5.1
downloaded and updated
but now phone doesn't even shows anything
if i connect usb and hold power+vol down button i just here a usb connected and disconnected tone only:crying:
please help.
believe kernel is only for CM12 .. how did u flash on CM13??
Need the blankflash please help
my phone hard bricked today while updating device software, i think i need the blankflash for xt1506, please someone help
legendracer said:
My moto e2 otus 1506 model is bricked. I will list things that I did.
1. Unlocked bootloader, installed moto drivers in PC.
2. Downloaded twrp
3. Flashed twrp.
4. Downloaded RR ROM based on cm13.
5. Downloaded gapps 6.0.
6. Downloaded blive kernel.
7. Copied to memory card, mounted it.
8. Twrp- erase all, format,clear cache- flash- ROM, gapps, kernel- clear cache-Reboot.
9. Phone works but lags a lot. Used it for few weeks. Tried kernel flash first and last, but sometimes it won't boot at all. At best ROM+gapps worked without issues, but phone lagged.
10. I thought it is coz of RR ROM and cm13 should be used. Downloaded cm13 snapshot.
11. Twrp flash fails, says, invalid zip file. Tried other cm13 files, same error.:crying:
12. Surprised I try RR again. It works.
13. After using the slow phone, I find time and after reading XDA, I decide to revert back to stock and try cm13 first.
14. Downloaded firmware files, 2 files, just in case 1 fails.
15. Tried fastboot commands. All well but it won't boot neither into recovery.
16. Tried twrp flash. Failed. Tried several times and it worked once.
17. Instead of living with RR ROM, I tried again with stock flash. Failed and twrp shows invalid errors and reboots.:crying::cyclops:
18. Left it for few weeks, battery drained, tried to charge by several methods, wall charger, PC charging , cmd script to reboot and charge, all failed. In fasboot mode it shows connected, battery low and charging, but does not charge.
Currently, all it shows is fastboot mode if lucky or else a white screen with 0 battery. How to bring it back to life?
Options and steps please. Hope to get help soon . thank you.
Click to expand...
Click to collapse
Bro will u please tell me how to root moto e2 1506
it worked for me bro pls guide me
Related
My phone was running at about 60% battery last night, and working fine. It was in my pocket and it vibrated. I was unable to turn it on or reboot it, even after removing the battery. I tried using the battery from my wife's S2 but still no luck. I tried connecting the power supply but it still wouldn't boot so I left it charging overnight.
This morning it alternately flashed a fully green battery and a fully black battery. If I press and hold the power button it starts the boot process - I get past the Samsung splash screen and see the first "Resurrection Remix" splash screen, but then it reverts to displaying the green battery.
Any ideas for how I can revive the phone??
itm said:
My phone was running at about 60% battery last night, and working fine. It was in my pocket and it vibrated. I was unable to turn it on or reboot it, even after removing the battery. I tried using the battery from my wife's S2 but still no luck. I tried connecting the power supply but it still wouldn't boot so I left it charging overnight.
This morning it alternately flashed a fully green battery and a fully black battery. If I press and hold the power button it starts the boot process - I get past the Samsung splash screen and see the first "Resurrection Remix" splash screen, but then it reverts to displaying the green battery.
Any ideas for how I can revive the phone??
Click to expand...
Click to collapse
Ok We cant say its bricked!! Because its booting up but not coming to homescreen rite? Are u able to get into recovery or download mode?? If ur able o then wipe the data cache and dalvik cache, reinstall the ROM again.. If Recovery doesnt shw up.. Then Use ODIN to flash original fw!! Even if u still couldn get it.. Order a USB JIG from Ebay and try getting into DOWNLOAD MODE!! Even after this its still working means ITS BRICKED !!
Start download mode and the flash a new stock firmware . And your phone isnt bricked .!
This is why I always make a backup.
If you can get into download mode you can fix it, if you can't it's a service centre job. Pretty simple really.
Try cleaning charging port..
Sent from my GT-I9100 using XDA
Uh oh...I managed to get into Recovery mode, did a factory reset and kicked off a re-install of the Resurrection Remix ROM from the external SD and it's hung at 50% (for 10 mins now) - at the "Extracting /system..." stage. I daren't interrupt it.
Any ideas???
Yes stop messing
1: If you dint have to save anything, wipe better to full wipe
Flash a stock Rom using Odin, than start again with custom roms.
OR
2: download your custom Rom again and flash, might be corrupt download.
atifsh said:
Yes stop messing
1: If you dint have to save anything, wipe better to full wipe
Flash a stock Rom using Odin, than start again with custom roms.
OR
2: download your custom Rom again and flash, might be corrupt download.
Click to expand...
Click to collapse
So it's OK to interrupt this ROM flash, even though it's stuck at 50%? Should I just hold the power button or remove the battery??
pull the battery
But I say flash stock Rom first, lengthy procedure I know, but safer
OK I decided to reflash RR 2.3, which had been running fine for a couple of weeks previously. Immediately after flashing (which worked OK) the boot process wouldn't complete - it got as far as the RR splash screen then died (screen blank, and needed a long press on the power button to restart).
This happened several times. Eventually I removed and replaced the battery and it finally booted.
Does this sound like a hardware problem? I've noticed that the phone often runs quite warm, but I don't know if that's normal.
You have to flash stock rom, only way to know if there is something wrong with your phone, run it for couple days.
Now to the heat issue, it is due to
1: modem
2: kernel
3: both
hi
so the story is - i have motorola xt910 (MAXX hd) from europe
i have installed bootmenu manager and safestrap 3.72
firstly the stock rom didnt work anymore,safestrap was disabled,but i have installed CW11 on slot 1 and everything was fine,until battery died
Now i cant turn on it, when i plug razr to wall charger its turn on by itself and stuck on M logo
when i plug to usb cable,sometimes the same - stuck on M logo on led is active - the strange thing that i dont turn it on but the logo is appearing
but i cant turn it on
i have tried VOLUME DOWN+VOLUME UP+POWER
nothing..
please help
talboris said:
hi
so the story is - i have motorola xt910 (MAXX hd) from europe
i have installed bootmenu manager and safestrap 3.72
firstly the stock rom didnt work anymore,safestrap was disabled,but i have installed CW11 on slot 1 and everything was fine,until battery died
Now i cant turn on it, when i plug razr to wall charger its turn on by itself and stuck on M logo
when i plug to usb cable,sometimes the same - stuck on M logo on led is active - the strange thing that i dont turn it on but the logo is appearing
but i cant turn it on
i have tried VOLUME DOWN+VOLUME UP+POWER
nothing..
please help
Click to expand...
Click to collapse
The led color,is it white?
If it is,then you must make or buy the factory cable and flash your stock rom with RSD Lite.
Sent from my Razr XT910
yes,its white
now i have managed somehow to turn it on
but the problem is that stock ROM in safestrap is always Disabled ,i cant use it ?
so i can use it only with factory cable? whats so special in it ?
do i have to use only original stock rom ? shouldnt safestrap to bypass it ?
talboris said:
yes,its white
now i have managed somehow to turn it on
but the problem is that stock ROM in safestrap is always Disabled ,i cant use it ?
so i can use it only with factory cable? whats so special in it ?
do i have to use only original stock rom ? shouldnt safestrap to bypass it ?
Click to expand...
Click to collapse
If you can turn it on then your battery is ok,just flash your stock rom with RSD Lite,root it,install Safestrap and happy flashing.
The factory cable allows you to flash the fastboot (stock rom) files when your battery is too low.
Did you try to get in to fastboot mode?
Pressing vol- vol+ and power button at the same time?
Look what's written for the battery,Battery OK-good,Battery Low-you need the factory cable.
Sent from my Razr XT910
welder73 said:
If you can turn it on then your battery is ok,just flash your stock rom with RSD Lite,root it,install Safestrap and happy flashing.
The factory cable allows you to flash the fastboot (stock rom) files when your battery is too low.
Did you try to get in to fastboot mode?
Pressing vol- vol+ and power button at the same time?
Look what's written for the battery,Battery OK-good,Battery Low-you need the factory cable.
Sent from my Razr XT910
Click to expand...
Click to collapse
i turned it on,everything was ok,plugged and unplugged cables several times,then once again when battery died
when i connect to a laptop - the led is whight
when i connect to wall charger - i have M logo and then battery with question mark
what does it mean ?
talboris said:
i turned it on,everything was ok,plugged and unplugged cables several times,then once again when battery died
when i connect to a laptop - the led is whight
when i connect to wall charger - i have M logo and then battery with question mark
what does it mean ?
Click to expand...
Click to collapse
first. installing safestrap and boot menu manager at same time is not recommended.
second. if I understood you, you flashed cm11 over stock ROM. but you provide no info about how you did it.My guess is you didn't wipe all recommend partitions.
that leads me to third, your battery stats probably were messed up. next time you charge it try to wipe your battery stats, there is apps in play store that will do it for you. some people say it doesn't does a difference, certainly your battery will not magically improve, but it does corrects weird behaviors.
If it doesn't works, try using RSD as welder73 told you. troubleshooting is easier in a clean and working system. what I am proposing is worthy to try if you have data that you cannot loose.
note: don't know how factory cable works, but I hope you are using it instead of directly connecting cable to the battery. cause charge might not be controlled if you charge directly to battery terminals... if you let it charge too much time it can damage battery.
xt910 can be a RAZR MAXX but not a MAXX HD which is a totally different phone.
angrist said:
first. installing safestrap and boot menu manager at same time is not recommended.
second. if I understood you, you flashed cm11 over stock ROM. but you provide no info about how you did it.My guess is you didn't wipe all recommend partitions.
that leads me to third, your battery stats probably were messed up. next time you charge it try to wipe your battery stats, there is apps in play store that will do it for you. some people say it doesn't does a difference, certainly your battery will not magically improve, but it does corrects weird behaviors.
If it doesn't works, try using RSD as welder73 told you. troubleshooting is easier in a clean and working system. what I am proposing is worthy to try if you have data that you cannot loose.
note: don't know how factory cable works, but I hope you are using it instead of directly connecting cable to the battery. cause charge might not be controlled if you charge directly to battery terminals... if you let it charge too much time it can damage battery.
xt910 can be a RAZR MAXX but not a MAXX HD which is a totally different phone.
Click to expand...
Click to collapse
tnx for anwering
whai i did :
1)installed bootmenu manager
2)installed safestrap
after that STOCK ROM stopped to work - i didnt perform any wipe
3)i have installed CW11 on slot 1
problems started when battery dies
4)somehow i have managed to turn it on and installed Slimbin on STOCKROM
now i have this question mark - cant turn it on and cant use RSD since battery is LOW, i have tried RSD before it said "fail" Razr refused or something..
so my question for the next time
shouldnt i install bootmenu prior to safestrap ?
what wipe should i do ?
how do i wipe partitions ?
talboris said:
tnx for anwering
whai i did :
1)installed bootmenu manager
2)installed safestrap
after that STOCK ROM stopped to work - i didnt perform any wipe
3)i have installed CW11 on slot 1
problems started when battery dies
4)somehow i have managed to turn it on and installed Slimbin on STOCKROM
now i have this question mark - cant turn it on and cant use RSD since battery is LOW, i have tried RSD before it said "fail" Razr refused or something..
so my question for the next time
shouldnt i install bootmenu prior to safestrap ?
what wipe should i do ?
how do i wipe partitions ?
Click to expand...
Click to collapse
ok. when you get into fastboot and try to RSD and get a Low Battery warning, the is no other way left... charge battery. or get a factory cable, there is a thread explaining how to build one.
first question. you have to choose one of them. for newbies, safestrap cause all new ROMs are prepared to work with that program. if later, u decide to test bout menu manager, you will have to uninstall safestrap ( of course you will not be able to use any ROM installed with safestrap). since boot menu manager is no longer supported, you will need to mod ROM zip file prior to flashing that's why i recommend sticking to safestrap for now. Don't install both, they are not meant to work together.
second question. To install in stock ROM, you have to wipe everything except sdcard and sd-ext where you personal data is (never tried, so can't help you more). for slot1 Wiping is not necessary first time, cause slot1 is fresh. next time yo install other ROM you will have to wipe data, cache and system. double check what you ate doing, so you don't wipe stock instead of slot1.
Wipe options are in safestrap.
SafeStrap and Boot Manager
I have accidently installed both apps on my Motorola Razr XT910 and my phone is now stuck on the red logo - I cannot get it into the bootloader to unbrick it with RSD Lite. Is there anybody who can advise ?
ok,i somehow managed to turn it on
now i want to flash 4.0.4
the phone itself form Norway,what ROM should i use? i tried to install Asian but it didnt work "some file not singed"
i just downlod zip file,unzip it, and choose xml file in RSD lite?
talboris said:
ok,i somehow managed to turn it on
now i want to flash 4.0.4
the phone itself form Norway,what ROM should i use? i tried to install Asian but it didnt work "some file not singed"
i just downlod zip file,unzip it, and choose xml file in RSD lite?
Click to expand...
Click to collapse
Yes,but flash the Europian fastboot file.
And don't try to flash ICS if your stock was JB.
You can flash JB fastboot file with RSD Lite if you want,that way you'll upgrade to JB.
About RSD Lite,I unzip file with it,if I remember correctly,click on start,choose decompress only and find your zip.
Sent from my Razr XT910
Okay.. I have a similar problem which I have ran into now..Yesterday I was just using my phone normally and was trying to call someone, when the phone immediately shut down..my guess was that the battery stats were screwed up..So I tried charging it and even I had the question mark on the battery when I connected it to the charger. I couldn't switch on the phone manually. I was on PA android jellybean 4.3.1. So should I also need a factory cable or something to restore my phone??
Thanks in advance
Hello,
My razr xt910 had stock rom and MIUI on 1st slot using safestrap and everything was going well then today the device shutdown as the battery was low, When I connect it to the wall charger it boots just to the MOTOROLA logo "the first one.. before the safestrap menu" I mean there is no sign that its charging or so and when I connect it to the PC only the led notification goes on.
I left it for while on the wall charger then the screen goes off just after I unplug it from the charger and I'm not able to boot it up again. so I back to plug it again. after many tries I managed to boot to safestrap recovery and changed the rom slot to the stock rom as I thought the problem with the MIUI rom restarted system and same problem happens.
and when I managed to pass the safestrap menu to the stock rom the device stuck at boot animation and either it keeps animating forever or it goes off after short time. tried to boot to fastboot menu (power+ vol down) it says battery low so...
- Is it really charging when it's connected to wall charger (showing moto logo) or when it's connected to the pc (led notification on) ? I tried to press vol down on both like some tutorial said but it didn't show the battery.
- After searching for solution, I didn't find the same problem happened to someone but similar ones that all were suggested to flash using rsdlite. can I flash different version of the stock one? I mean for my region there's 2 ics frimwares and I don't remember which one was the device on so it's ok to use any? Also if rsdlite is suggested in my case could you please provide detailed steps as I didn't use rsdlite or to flash frimwares before "was just flashing custom roms using SS". And how would I use while everytime I go to fastboot menu I see battery low msg .
- Could the problem be a battery's one? As the device sometimes goes off just after unplugging it and I can't power on it even I left it on wallcharger for like 30 mins.
Any help will be appreciated.
Thanks in advance.
I think RSDlite is the solution. So if your phone says low battery. There's a way to charge it with the normal charging cable. I bricked my phone about two months ago. I know that installing something wasn't the cause of this problem but i ALWAYS still any ROM or zip file with 80% charge, no less. Assuming that u still got the stock ROM and system folder. If not then it won't work.
1. Press power + vol down + vol up at the same time.
2. Go into AP fastboot
3. Press the power button. The screen should turn off at this point.
4. Plug in charging cable, after that the Motorola logo will show up. After that I don't remember if charging battery icon came up or screen goes black. I don't think it does. Sorry. But if does, then yay???
5. Let it charge for 1 hour or more. Just so that the charge is okay.
6.Check if its charging by going in AP fastboot and checking if battery is okay.
It worked for me on my spyder. Since I still had my stock ROM and my system folder wasn't deleted. If this doesn't charge then you have to buy one of those special charging cables.
If this works for you reply. IDK if installing firmware is different for xt910 but ik how to for xt912. It fairly easy.
---------- Post added at 05:16 AM ---------- Previous post was at 05:07 AM ----------
If I don't reply within 8 hours or more. It's because I'm still sleeping. Since it's 12am here in the US East.
GreatItami said:
I think RSDlite is the solution. So if your phone says low battery. There's a way to charge it with the normal charging cable. I bricked my phone about two months ago. I know that installing something wasn't the cause of this problem but i ALWAYS still any ROM or zip file with 80% charge, no less. Assuming that u still got the stock ROM and system folder. If not then it won't work.
1. Press power + vol down + vol up at the same time.
2. Go into AP fastboot
3. Press the power button. The screen should turn off at this point.
4. Plug in charging cable, after that the Motorola logo will show up. After that I don't remember if charging battery icon came up or screen goes black. I don't think it does. Sorry. But if does, then yay???
5. Let it charge for 1 hour or more. Just so that the charge is okay.
6.Check if its charging by going in AP fastboot and checking if battery is okay.
It worked for me on my spyder. Since I still had my stock ROM and my system folder wasn't deleted. If this doesn't charge then you have to buy one of those special charging cables.
If this works for you reply. IDK if installing firmware is different for xt910 but ik how to for xt912. It fairly easy.
---------- Post added at 05:16 AM ---------- Previous post was at 05:07 AM ----------
If I don't reply within 8 hours or more. It's because I'm still sleeping. Since it's 12am here in the US East.
Click to expand...
Click to collapse
Thanks for your reply,
now the problem is that I can't boot it when it's unplugged and when I try to do this while plugging, it still shows the same.. Moto logo without any sign to be charging.
Just saw some solutions that require me to open the back battery cover and connect the wires to the battery, but I'm really afraid to proceed with these steps to mess with the device :/
Also a solution said that the device doesn't charge like this, so I have to get a "factory cable" and do the rsllite thingy using this cable.
Is this method recommended? isn't there any easier way to try before proceeding with this ?
The easiest way to charge it is they way I said. But if you can't do that then factory cable is your other option.
GreatItami said:
The easiest way to charge it is they way I said. But if you can't do that then factory cable is your other option.
Click to expand...
Click to collapse
Thanks for your help :fingers-crossed:
Before taking the decision to make the factory cable I gave some tries because I'm not really experienced with this and wanted the easiest way to fix it. And I did managed to reach the safestrap menu and tried to charge it.
At first safetrap showed battery 99% after a while It changed to 5%+ I assumed it's charging that way and that actually was happening
I waited till it passed 60% and tried to reboot the system to stock slot but it I couldn't!! it stuck again at the stock rom's boot animation.
I forced to shutdown (power + vol down) then installed Liquid smooth rom that I had stored there and it was done successfully and I managed to boot into it. so now the problem is I can't boot to the stock rom but safetrap still works and I can boot to the any other slot. that means the problem I had before may occur again if the battery went low.
Now I will have to use rsdlite to flash the stock rom (unbrick it) right? If yes, Are there any steps that should be done first? I mean should I delete the other slots and keep only the stock one or it won't affect rsdlite?
Nex| said:
Thanks for your help :fingers-crossed:
Before taking the decision to make the factory cable I gave some tries because I'm not really experienced with this and wanted the easiest way to fix it. And I did managed to reach the safestrap menu and tried to charge it.
At first safetrap showed battery 99% after a while It changed to 5%+ I assumed it's charging that way and that actually was happening
I waited till it passed 60% and tried to reboot the system to stock slot but it I couldn't!! it stuck again at the stock rom's boot animation.
I forced to shutdown (power + vol down) then installed Liquid smooth rom that I had stored there and it was done successfully and I managed to boot into it. so now the problem is I can't boot to the stock rom but safetrap still works and I can boot to the any other slot. that means the problem I had before may occur again if the battery went low.
Now I will have to use rsdlite to flash the stock rom (unbrick it) right? If yes, Are there any steps that should be done first? I mean should I delete the other slots and keep only the stock one or it won't affect rsdlite?
Click to expand...
Click to collapse
If you want to get stock back then yes. Cuz I don't if installing a ROM on stock will fix it. But before you do anything,backup your files on internal storage to a computer.
GreatItami said:
If you want to get stock back then yes. Cuz I don't if installing a ROM on stock will fix it. But before you do anything,backup your files on internal storage to a computer.
Click to expand...
Click to collapse
Sorry for bothering you But I wanted to ask about something before starting the rsd to install the frimware.
Now as I told before I can boot to safestrap menu and can boot to other slots but not the stock one so...
- Can I install the frimware using safestrap?
- Should I try to boot the stock recovery and try a factory reset to the stock rom? if yes, will that affect safestrap? I mean if it didn't fix the stock rom will I still have access to safestrap? in other words Will safestrap will be still installed after doing a factory reset from the stock recovery?
Thanks alot for your help
Nex| said:
Wanted to ask about something before starting the rsd to install the frimware.
Now as I told before I can boot to safestrap menu and can boot to other slots but not the stock one so...
- Can I install the frimware using safestrap?
- Should I try to boot the stock recovery and try a factory reset to the stock rom? if yes, will that affect safestrap? I mean if it didn't fix the stock rom will I still have access to safestrap? in other words Will safestrap will be still installed after doing a factory reset from the stock recovery?
Thanks alot for your help
Click to expand...
Click to collapse
Anyone? :/
Nex| said:
Anyone? :/
Click to expand...
Click to collapse
Have you tried booting in to Safestrap, switching to the stock Rom and then wiping Cache and Dalvik? I would always try that before a factory reset. Also, if you are running the Xposed Framework in your stock slot the next step I would recommend is that you try flashing the xposed disabler. If you don't have the xposed disabler on your SD card you can download it from the thread that you originally downloaded xposed from.
swing4thefence said:
Have you tried booting in to Safestrap, switching to the stock Rom and then wiping Cache and Dalvik? I would always try that before a factory reset. Also, if you are running the Xposed Framework in your stock slot the next step I would recommend is that you try flashing the xposed disabler. If you don't have the xposed disabler on your SD card you can download it from the thread that you originally downloaded xposed from.
Click to expand...
Click to collapse
I've just switched to the stock and wiped Dlavik and cache (by safestrap) and still same problem... stuck at boot animation
I've never installed xposed before.
Shall I do a factory reset through the stock recovery or it will delete safestrap?
Thanks you for your help.
Nex| said:
I've just switched to the stock and wiped Dlavik and cache (by safestrap) and still same problem... stuck at boot animation
I've never installed xposed before.
Shall I do a factory reset through the stock recovery or it will delete safestrap?
Thanks you for your help.
Click to expand...
Click to collapse
I Deleted my stock slot and installed SlimKat over it and Safestrap still so I think Safestrap must insert code between the bootloader and the actual Rom. but I'm not 100% sure. Do a nandroid backup of your Miui slot and then try it. you can always reinstall Safestrap if you lose it.
Hi guys! I have a huge problem here. I had the latest nightly release of CM13 installed but I wanted to come back to stock kitkat for the better use of battery. So I downloaded the V20j_620r.zip, wiped everything except sdcard on twrp and then installed the zip. Once rebooted the phone just reboot every 2sec on lg logo without giving me the chance to enter recovery/download mode (i tried every possible buttons combinations without results). I tried also to removing battery,sim and sd card, plug the phone to the pc which doesn't recognize it and having the phone stuck on the yellow triangle because it want to put the battery in. If I plug the battery in it goes on the charging logo but it doesn't have time to load the percentage of battery and after 2 sec it reboot again to lg logo constantly. I think that maybe it wanted to be repartioned before installing the previous version of android, but without giving me the chance to connect it to the pc I really don't know what to do now. If you have some advice, it is very appreciated.
Thanks
Do you try to flash KDZ in download mode? (when phone boot up hold volume up and put usb cable)
Boki11111 said:
Do you try to flash KDZ in download mode? (when phone boot up hold volume up and put usb cable)
Click to expand...
Click to collapse
you are my hero! didn't think about that! the phone entered in "firmware update" and was detected by the laptop thank you very much, I really don't know how to say thank you! You saved me!!!!
The phone told me there was a new update I started to install it, got to reboot and now is just on the elephone logo which comes every 20 sec and goes again. I cannot turn the phone off or do anything with it. Any help please
For me just shut down the phone and then reiniciat the phone ....work for me....
Enviado do meu thor através de Tapatalk
same problem here.. wtf nice update elephone, we cant be the only ones right?
now stuck on logo, restarting every 3 seconds with 100% battery...i m not even sure it will work again if battery is drained out
i can do nothing, no trys to get in factory mode or shut the phone down worked..
stuck on elephone log after upgrade
My elephone P9000 is now cycling the elephone logo every 8 seconds or so after the latest audio upgrade... It will not switch off or do anything else. Did you solve the problem. Or anyone else help. Can you share with me? Thank you.
same problem here.. wtf nice update elephone, we cant be the only ones right?
now stuck on logo, restarting every 3 seconds with 100% battery...i m not even sure it will work again if battery is drained out
i can do nothing, no trys to get in factory mode or shut the phone down worked..
Click to expand...
Click to collapse
so my battery was fully empty now.. i even pressed the power button 100 times after the battery was empty, to make sure all current is out of the phone.
plugged in charger... after 10 seconds phone start itself (after viewing the picture of empty battery) and elephone logo shows short and then back to showing picture of empty batterie cycle. After some minutes, and battery is loaded a little bit, elephone logo cycles again.
So rest in piece my p9000, i can nothing, i cant do anything from my pc because its only starting for like 5 seconds, i cant shut it down because of that and i cant get in factory mode
i am so pissed right now
just wanted to install the new update, everything worked fine like all the times before that and now my phone is ready for the trashcan.
Is there any way to reset the software without getting in factory mode?
Reset from sp flash tools?
Pro4TLZZ said:
Reset from sp flash tools?
Click to expand...
Click to collapse
the phone turns on and off in a cycle of 5 seconds, so that wont work
and i cant stop that cycle.
even if battery is 0% (i even press power button many times so really its drained out). If i recharge it, the cycle starts again without me doing anything. The Power button is not broken or something. it all began after i started new ota update and the phone rebooted like "mkitty" has the same problem it seems
Same for me, I have no idea how to restart my phone. And i dont want to loose all data I have on it.
have you tried to hold the volume up and power at the same time during the restart process to try and force recovery?
xvicedice said:
have you tried to hold the volume up and power at the same time during the restart process to try and force recovery?
Click to expand...
Click to collapse
Hello,
Yes . I have tried that.
I have a list of options that come up on the screen.
I have tried them apart from the wipe data/factory reset.
But it is still the same result.
Thank you for help.
Any more ideas?
what OTA update version did you update?
Simplytouched said:
what OTA update version did you update?
Click to expand...
Click to collapse
It said something about wifi and audio update. I followed the instructions as per a previous update (which worked OK). I never took notice of any version numbers etc.
I have all I need to flash a new rom to the bricked phone but when I connect the off phone to my pc the usb not recognised comes up and I cannot flash the rom to the phone. and yes I have the mediatek vcom drivres install. Why did I buy a Chinese phone elephone p9000 please stay well away from it. on paper is a great phone but in reality does not perform in any sense, battery only lasts 7 hours if I was lucky camera crap, gps works most of the time all that ram and power and t struggles with some videos o dear god. never again. now I cannot even read what I have on the sd cos is formatted for the phone.
juka1 said:
I have all I need to flash a new rom to the bricked phone but when I connect the off phone to my pc the usb not recognised comes up and I cannot flash the rom to the phone. and yes I have the mediatek vcom drivres install. Why did I buy a Chinese phone elephone p9000 please stay well away from it. on paper is a great phone but in reality does not perform in any sense, battery only lasts 7 hours if I was lucky camera crap, gps works most of the time all that ram and power and t struggles with some videos o dear god. never again. now I cannot even read what I have on the sd cos is formatted for the phone.
Click to expand...
Click to collapse
Its actually a great phone. Do you have twrp installed and can you get access to it? You could always boot into twrp transfer over the ROM and install it from there. If you have installed the vcom drivers then when the USB not recognized alert pops up. Go to settings and device manager. Right click the unknown device and click let me pick driver. You should be able to install it from there
The only thing I can suggest is to take the back panel of and unplug the battery. There videos on how to do this if you search YouTube or the forum. Effectively you perform a hard reset of the phone.
If and when you do get it working just twrp installed and do a backup of the whole phone working before performing any future upgrades or Rom changes. Its just better safe then sorry.
thenk you very much for that
The problem is that when I connect the phone on the off to the pc starts again the cycling through the elephone logo so the pc sees the phone for a few seconds in which does not recognises it and then is like the phone goes off until the next cycle so no time to go to device manager and install manually. but thank you for the comment.
removing the battery will void the warranty. I had the phone only since may.
It's unlikely it really matters. Your phone seller not going to take it back or fix it for free just because it's bootlopping. Well they may so just ask them. If you can't get it into recovery then a battery disconnect or contact your seller are your options
thank you
Android-UK said:
It's unlikely it really matters. Your phone seller not going to take it back or fix it for free just because it's bootlopping. Well they may so just ask them. If you can't get it into recovery then a battery disconnect or contact your seller are your options
Click to expand...
Click to collapse
I can get it into recovery mode but I haven't got any software install in the sd card to do a recovery that is why I thought my only option was the sp flashing tool and the room which I have
juka1 said:
I can get it into recovery mode but I haven't got any software install in the sd card to do a recovery that is why I thought my only option was the sp flashing tool and the room which I have
Click to expand...
Click to collapse
Well in that case all you need is a stock rom and yes just flash them with sp tools and it should start booting again. The fact you can get to recovery is a good sign.
Android-UK said:
Well in that case all you need is a stock rom and yes just flash them with sp tools and it should start booting again. The fact you can get to recovery is a good sign.
Click to expand...
Click to collapse
sorry for all of this and thank you very much for your help but when I put the phone in recovery mode by pressing the down volume and power key and connect the phone to the pc it is not recognized by the pc so I can't flash the room