Help Help help-
very hard brick due to Wrong Flashing,
unable to Boot into FAstboot
unable to boot into edl
unable to boot into recovery
only a red light appear during usb or changer connect
any way to recover this device please help-
thanks in advance,
XN Logos said:
Help Help help-
very hard brick due to Wrong Flashing,
unable to Boot into FAstboot
unable to boot into edl
unable to boot into recovery
only a red light appear during usb or changer connect
any way to recover this device please help-
thanks in advance,
Click to expand...
Click to collapse
Wrong flashing how ? Did you try test point method ? Does device manager show anything when connected to pc ?
Sent from my Redmi Note 3 using Tapatalk
If your area/country of residence has Xiaomi Service Centres, I'd suggest you go there and get your phone repaired. Else, the test point method is your best bet for getting your phone working again. Here's a guide to the test point method - http://xiaomitips.com/guide/how-to-unbrick-redmi-note-3-snapdragon-best-solution/
Please note that the test point method is rather long and involves taking your device apart by yourself. Proceed at your own risk.
IF you can do it try test point. It works 100% but be careful while doing it as you dont want to break you're device. Dont worry its very hard to totally brick redmi note 3. and what you are saying can be repaired with test point. So be careful and try it.
i see a method http://forum.xda-developers.com/redmi-note-3/how-to/method-to-flash-twrp-recovery-unlock-t3473294/post69037237 and according this method replace stock recovery by twrp or any custom recovery i do same like this and get permanently brick,
ya a red light is apeear when connect to pc or charger, i know test point method is work but it's difficult, can this device repairabale through software box,
Relax and then go to service centre. They will solve your problem. Is your device in warranty period? If not you may have to pay for this.
SOLVED!!! 2 very hard brick xiaomi redmi note 3 pro
Dont go to the service centre, it wasting time and lot of MONEY, i swear!!! i'v solved the problem. The problem is after u flash normally (edl mode, with miflash 64bit, suitable ROM, deep flash cable or test point, readable port *qdloader9008), then u hv to fit out battery from the socket and fit in it back, then charge your phone, if the battery charging window appears, TAADAAAA, u'v done!!!!
Related
Hey guys. So, I bricked my phone. I installed RomManager, then ClockworkMode through it, thus I knew that this phone is not supported. It wasn't there in that list, so I chose Commtiva z71 or something like that. My phone doesn't get in download mode anymore. Could this be fixed at home? I really don't want to take it to a service centre.
Please help me. Thanks!
There's a few people who have done this and I don't think any of them have been able to find a way to get it working again. I think you will have to send it to repairs, sorry
Sent from my GT-I5500 using Tapatalk
after rooting my phone samsung galaxy 5 doesnt turn on
i root my phone with universal androot,everything was ok,i reboot my phone and tray with rom manager to do a backup of my rom,i choose a model that wasent my model,and after that i tray to partition my sd card and was there when my phonr turn off and its never turn on again.............,do someone have a solutions!!!!!!
Jordanooo said:
There's a few people who have done this and I don't think any of them have been able to find a way to get it working again. I think you will have to send it to repairs, sorry
Sent from my GT-I5500 using Tapatalk
Click to expand...
Click to collapse
Sent from my GT-I5500 using Tapatalk
Threw it guys. It sucked anyway.
It doesn't suck, its amazing
Sent from my GT-I5500 using Tapatalk
dead ur smart
quebeco said:
i root my phone with universal androot,everything was ok,i reboot my phone and tray with rom manager to do a backup of my rom,i choose a model that wasent my model,and after that i tray to partition my sd card and was there when my phonr turn off and its never turn on again.............,do someone have a solutions!!!!!!
Click to expand...
Click to collapse
Exactly as u .i try to backup my rom and my samsung was dead in 5 seconds.I sent them to service twice The firt my motherboard is dead and i wait the second time because i thing is dead again I dont use rom manager never
did you tried to download ClockWorkmodRecovery(cwm) than flash with odin multi downloader and then wipe data?
first step i found in solving this issue
i also flashed the same recovery through rom manager. i think i have found the first step in solving this issue. all now is that i need help of all of you guys.
All I did was removed my battery while still being connected to usb . After this i kept holding the option button (the button on the upper leftmost side) and with this being hold i inserted the battery. Now my pc recognised the device as samsung usb composite device and also the odin recognises it. but whatever i try my phone stucks at setup connection in odin. pls help.
this can help thousands of bricked g5s.:angel::angel::angel::angel::angel:
no need
rstar900 said:
i also flashed the same recovery through rom manager. i think i have found the first step in solving this issue. all now is that i need help of all of you guys.
All I did was removed my battery while still being connected to usb . After this i kept holding the option button (the button on the upper leftmost side) and with this being hold i inserted the battery. Now my pc recognised the device as samsung usb composite device and also the odin recognises it. but whatever i try my phone stucks at setup connection in odin. pls help.
this can help thousands of bricked g5s.:angel::angel::angel::angel::angel:
Click to expand...
Click to collapse
no need to pull battery out and insert it back just insert the battery ,hold down the option key & insert usb cable thats it....but none of these gonna work you will need JTag to flash
You can even try JIG. Because, you've messed with recovery and boot partition but not the arm11boot (bml8). So, JIG (search Google, it is as cheap as $2 and you can even make one at home) can help you.
If it didn't, just search for JTAG services nearby your area. They'll charge you $20-$40 and your g5'll be alive.
Bhargav97 said:
You can even try JIG. Because, you've messed with recovery and boot partition but not the arm11boot (bml8). So, JIG (search Google, it is as cheap as $2 and you can even make one at home) can help you.
If it didn't, just search for JTAG services nearby your area. They'll charge you $20-$40 and your g5'll be alive.
Click to expand...
Click to collapse
That's not true, sadly. ROM Manager embeds a version of flash_image that will try to flash a boot image to bml8 if the device is not properly recognised. That's what happened for the OP, so a JIG will not resurrect the phone.
Oh...Sorry, I didn't knew that! So, final option left for OP is a JTAG flash.
@psyke83
Seems like out of your 3 bricks, this is one.
My phone has been to 9.0.0.197,but now the phone can not boot anything.no screen, no recovery, no fastboot.but when i connect cable to pc can still show fastboot device.i tried funkeyhuawei,dc-unlocker to flash but still no on. Please help me! Thank you everyone!
when you plug it into the computer (windows) in device manager does it show adb bootloader ? or usb ser ?
ColaTao said:
My phone has been to 9.0.0.197,but now the phone can not boot anything.no screen, no recovery, no fastboot.but when i connect cable to pc can still show fastboot device.i tried funkeyhuawei,dc-unlocker to flash but still no on. Please help me! Thank you everyone!
Click to expand...
Click to collapse
If your phone is under warranty I would suggest sending it in to a service center.
The only other way is opening the back cover of the phone and using testpoint. Removing back cover will void warranty, and is not suggested if you don't know what you're doing.
tokoam said:
when you plug it into the computer (windows) in device manager does it show adb bootloader ? Or usb ser ?
Click to expand...
Click to collapse
yes can show the adb bootloader device. But phone still black screen
ColaTao said:
yes can show the adb bootloader device. But phone still black screen
Click to expand...
Click to collapse
FYI I was in the same situation as you, Huawei denied my repair and said I had water damage.And I clearly did not have water damage once they see black screen and red led they always deem it as water damage.There was also another post where someone claimed water damage as well after they sent in there bricked device.At the end of the day I had to use test point recovery to get my device working again.
tokoam said:
FYI I was in the same situation as you, Huawei denied my repair and said I had water damage.And I clearly did not have water damage once they see black screen and red led they always deem it as water damage.There was also another post where someone claimed water damage as well after they sent in there bricked device.At the end of the day I had to use test point recovery to get my device working again.
Click to expand...
Click to collapse
ok thank you！i will try!
Hello, can please explain what is test point recovery? How can i do test point recovery?
Each device has a few contacts on the main board for connecting test point consoles in case bootloader or USB port is destroyed but you need proprietary cable and software to accomplish that. USB to test point is not always possible.
Hope someone can help me.
My Redmi Note 5 is stucked n Mi-Recovery 3.0 screen with 3 options: Reboot - Wipe data - Connect with MiAssistant. and continue to go in loop until the battery will be zero.
I was try everything to get connected, and flash again the firmware but no result, first and I think main problem is that my PC cannot see the phone, then with all SW I'm sure I can try to re-install everything and recover back my phone. Data is not a problem since I have all backup in MI account and Google account. I hope some one expert can help me to solve this unpleasant situation.
Is already out of warranty and send to MI service cost 36 EURO just for checking and then more than 90 EURO for repairing, is not worthing the cost.
P.S. I downloaded and try with ADB; Flash; MI Tool, USB debug etc..
I'm desperate mother of two kids and I need this phone, now I'm using a very old one.
Thank you
You try mi flash tool, but the phone can not recognized? Fastboot mode working? When yes, maybe Windows install the wrong driver. Look in the device manager and install it when it the wrong one manual
Hi Joke, thank you for your interest in my problem.
You can see the screenshot I just made it and I was trying to connect the phone, I installed any diver as possible but the PC is not recognize it.
joke19 said:
You try mi flash tool, but the phone can not recognized? Fastboot mode working? When yes, maybe Windows install the wrong driver. Look in the device manager and install it when it the wrong one manual
Click to expand...
Click to collapse
matsalleh said:
Hi Joke, thank you for your interest in my problem.
You can see the screenshot I just made it and I was trying to connect the phone, I installed any diver as possible but the PC is not recognize it.
Click to expand...
Click to collapse
And what's with the windows device manager? U look inside
I have an update, now I can flash the Rom using Xiaomi MI tool V2. Then after finish message say that installation was successfully, but when I restart the phone is going back again on same position with Mi-Recovery 3.0. I noted that if I use MI Phone Assistant in certain conditions I can see the phone as "HD" in my PC. There is anything I can do to revive my phone?
I hope someone can help me. Thanks
When i flashed the Evolution X Rom to Stock rom It Got Failed And My Device Is Not Turning ON.
Whenever I Tried To Install stock Rom using mi flash tool It Is Saying "Cannot Recieve Hello Packet" & write time out,maybe device was disconnected Please Help ME To Fix
The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.
papsr6 said:
The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.
Click to expand...
Click to collapse
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...
wetito said:
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...
Click to expand...
Click to collapse
I Had Tried EDL flashing from Unlock Tool Flashing Done Perfectly But Formatting Failed..Is it a partition error ?.. The Display is not turning on.. No Signal Only The Signal is Entering EDL mode
wetito said:
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...
Click to expand...
Click to collapse
papsr6 said:
The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.
Click to expand...
Click to collapse
My Phone Is Now Like This :
hishamhsm said:
I Had Tried EDL flashing from Unlock Tool Flashing Done Perfectly But Formatting Failed..Is it a partition error ?.. The Display is not turning on.. No Signal Only The Signal is Entering EDL mode
Click to expand...
Click to collapse
What you wrote is not good... I don't know unloock tool. But before use this applications is necessary read carefully the instructions. It seems you didn't have do this. Good luck. Ps: if your phone boot into fastboot reflash stock via miflash... If you don't have made a big damage it will work. Very import is select the correct slot before flash... In my case i always select slot a to make a clean and safe installation
wetito said:
What you wrote is not good... I don't know unloock tool. But before use this applications is necessary read carefully the instructions. It seems you didn't have do this. Good luck. Ps: if your phone boot into fastboot reflash stock via miflash... If you don't have made a big damage it will work. Very import is select the correct slot before flash... In my case i always select slot a to make a clean and safe installation
Click to expand...
Click to collapse
is mi authorized account needed
hishamhsm said:
is mi authorized account needed
Click to expand...
Click to collapse
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary
wetito said:
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary
Click to expand...
Click to collapse
no fastboot , no charging
wetito said:
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary
Click to expand...
Click to collapse
will you help me to flash my phone via teamviewer
Sorry if you have damage bootloader (so fastboot don't work), the only way is edl. But i don't know how to solve edl flash fail. You had ask to other user, or search with Google. Or i'm afraid for you... Buy new phone. For the future if you want modding... Do it carefully
wetito said:
Sorry if you have damage bootloader (so fastboot don't work), the only way is edl. But i don't know how to solve edl flash fail. You had ask to other user, or search with Google. Or i'm afraid for you... Buy new phone. For the future if you want modding... Do it carefully
Click to expand...
Click to collapse
Thanks Bro Thanks For Your Support,.... Love From Kerala , India
Good luck
Same thing happened to me then i went mi authorised service centre and they charged 179rs and now my phone is working fine
azeem_saifi0411 said:
Same thing happened to me then i went mi authorised service centre and they charged 179rs and now my phone is working fine
Click to expand...
Click to collapse
is that phone under warranty while it was bricked
hishamhsm said:
is that phone under warranty while it was bricked
Click to expand...
Click to collapse
Sorry no. You have the bootloader unlocked... If your restore via edl will fail, in my opinion the best choice is buy a new phone. I don't know in your country. considerating that motheborard is not damaged... But phone must be open... The minum cost of this repair i think could be 100 € (convert in your currency). On YouTube there are a lot of tutorial how to do by yourself... But i'm not shure you have all skills...
wetito said:
Sorry no. You have the bootloader unlocked... If your restore via edl will fail, in my opinion the best choice is buy a new phone. I don't know in your country. considerating that motheborard is not damaged... But phone must be open... The minum cost of this repair i think could be 100 € (convert in your currency). On YouTube there are a lot of tutorial how to do by yourself... But i'm not shure you have all skills...
Click to expand...
Click to collapse
I Have Given It to A repair shop. They told me that that is emmc/UFS chip issue. So they will reprogramme the chip fix it and give the phone to me... They Told that it should fix..
Anyway I'm from India
hishamhsm said:
I Have Given It to A repair shop. They told me that that is emmc/UFS chip issue. So they will reprogramme the chip fix it and give the phone to me... They Told that it should fix..
Anyway I'm from India
Click to expand...
Click to collapse
I suppose that was the problem. I hope the repair shop in india are cheapest than in italy for the future... Make Modding with care
wetito said:
I suppose that was the problem. I hope the repair shop in india are cheapest than in italy for the future... Make Modding with care
Click to expand...
Click to collapse
Repairing cost around 10dollars . In India repairing cost is low but the price of mobile phones and spare parts are too high due to tax.
Thank you so much for your help and support bro. Love From India❤❤
I was using my phone like normal when it froze on me. I shut down my phone as I usually do when it freezes using the Power off + Vol Down. After turning the phone off, it refused to turn back on again, the light indicator for charging also does not work anymore when plugging in the charger. I did a bit of research and found out that it is possibly bricked. The way they suggested to fix this issue is to flash the phone with the stock rom. So here are the things I've tried:
1. Using SP Flash Tool (not really sure how this one is supposed to work, it is asking me for a "Scatter Loading File" which to my knowledge, isn't part of the ROM file I downloaded from xiaomi.)
2. Booting into EDL mode by shorting the pins and Using the official Mi Flash Tool (This one barely worked for me, it got into the process of flashing but asked me for an authorized Mi Account, after a few hours of research I found out that you can't get one.)
3. Changing the original firehose file with the modified version to bypass the authentication (Still asked me to authenticate)
4. Other Flash Tools (Qualtek, MiracleBox, Qualcomm Flash tool, etc. All failed)
Not really sure what to do at this point, I am unable to launch into fastboot or recovery, phone is completely unresponsive. The only thing that is giving me hope is that the phone is detected in the device manager of my pc as Qualcomm HS-USB QDLoader 9008 (COM3). Is the phone dead or is it just bricked, all answers will be highly appreciated, Thanks in Advance
Take phone to authorized service center and let them try to fix it.
jwoegerbauer said:
Take phone to authorized service center and let them try to fix it.
Click to expand...
Click to collapse
Well it is kind of the only possible way because Xiaomi locked down the EDL mode and render a phone truly as useful as a brick, when bricked, unless you sign in with a authorized mi account. Also 99 percent of time the people online claiming that they can fix the device, it is a scam.
However Xiaomi store will probably not fix the phone (it is 3 years old) for the OP (original poster) and try to convince him to move on to new Xiaomi phones because, Xiaomi will earn more...
LR7875 said:
Well it is kind of the only possible way because Xiaomi locked down the EDL mode and render a phone truly as useful as a brick, when bricked, unless you sign in with a authorized mi account. Also 99 percent of time the people online claiming that they can fix the device, it is a scam.
However Xiaomi store will probably not fix the phone (it is 3 years old) for the OP (original poster) and try to convince him to move on to new Xiaomi phones because, Xiaomi will earn more...
Click to expand...
Click to collapse
would a motherboard replacement work?
vaizardsparagon said:
would a motherboard replacement work?
Click to expand...
Click to collapse
1000000 percent this will work because by replacing the motherboard, your corrupt data and chips (fried EMMC flash storage) (and snapped snapdragon) will be replaced.
Exactly same thing happened with my Poco F1 on 20th Aug. It comes up as Qualcomm HS-USB QDLoader 9008 (COM3) when connecting to my laptop.
What would be the cost for getting motherboard replaced? I want to be able to use my phone with minimal effect to its state before the issue happened. Want to avoid any resets.
chmohit25 said:
Exactly same thing happened with my Poco F1 on 20th Aug. It comes up as Qualcomm HS-USB QDLoader 9008 (COM3) when connecting to my laptop.
What would be the cost for getting motherboard replaced? I want to be able to use my phone with minimal effect to its state before the issue happened. Want to avoid any resets.
Click to expand...
Click to collapse
I'm afraid to say this but i think that your phone was stuck in EDL mode. here in my country the technicians offer remote EDL flash.. no success no payment transaction..