Good to all, my P9000, not quite know why, yesterday had a problem with the rear camera is no longer detected, I tried to do a reset manufactures, not being possible, (??????) ,, then I chose to reinstall the rom originates via flashtools, went well, but when you turn the device does not respond, and at this point does nothing, nothing at all ... someone expert in these assuntis can help me before shipping guarantee .. ..
At this point the device, is dead, not power, is not detected by the PC, does not load anything ... ... does not enter recovery ....... please ask for help, because this time was the one who had ..... well there
Enviado do meu SHIELD Tablet K1 através de Tapatalk
Try to push power on button a bit longer at first start
No... A try everything... When charge nothing, no Led changing nothing... I think the its off
Enviado do meu thor através de Tapatalk
The last chance.
I have similar problem.
I had to disconnect the battery.
I flashed the new firmware via flashtool without battery. After the flashing, I connected the battery.
Uff.
The phone was OK.
How you do that.... How to disconect the battery....
I have do it, I can instal de rom, but the problem is not the rom.. Ia other think else, maybe the mathrtboard... It not reboote... Instal the rom but no reboote... Is dead, I try to go for delivery it to [email protected] to the warranty.....
Enviado do meu thor através de Tapatalk
Related
Hi guys!
First of all thxs a lot for everything you have tought me about phones in these years. I really hope you can help me with this one.
I have an Xperia S, locked bootloader, but rooted and with CWM installed by the instructions of this thread: http://forum.xda-developers.com/showthread.php?t=1939875. It worked fine.
I've had tried to flash a rom using the update.zip thing. All process went ok. Now my phone starts in black screen and reboots all time.
No led is shown when connected to wall. No led is shown ever (Still I haven't let the battery die, since it happened last night)
I've tried to flash something but flashtool doesn't recognize the phone any longer (it did before the accident). Neither PC companion. My PC shows in the Device Manager a SEMC HSUSB device for some seconds until phone reboots again and disappears.
I have a hope that if I fix that, I could try to flash some stock rom/kernel or something into the phone... but I haven't been lucky with that.
Any idea how I can relive my phone?
Please help me. Thanks in advance
If u cant remove the battery remove it and reinsert it
Dun try to switch on n try flashing ftf
If its non removable
Force shutdown by pressing volume up + power key till u feel 3 vibrations
Now try flashing ftf using flashtool
I dun think it's a hard brick certainly not possible wid a locked bootloader
It's non removable, so I tried hard reset (volume up + power key until 3 vibrations). Then, I tried to flash. Same thing, phone is not recognized (even if drivers were installed before and was recognized before)
WenSes said:
It's non removable, so I tried hard reset (volume up + power key until 3 vibrations). Then, I tried to flash. Same thing, phone is not recognized (even if drivers were installed before and was recognized before)
Click to expand...
Click to collapse
Can u try the same step on a different computer??
I will try that I'll let you know.
Enviado desde mi Nexus 7 usando XDA Premium HD app
WenSes said:
I will try that I'll let you know.
Enviado desde mi Nexus 7 usando XDA Premium HD app
Click to expand...
Click to collapse
K
Tried to go to another PC... Same thing, no recognized device... PC companion didn't recognized the device either (for the repair function)
Please people, I'm out of ideas...
Tell me if you need more info for helping
Enviado desde mi Nexus 7 usando XDA Premium HD app
which Rom u tried to flash..
have u tried asking it on Xperia S forum
WenSes said:
Tell me if you need more info for helping
Enviado desde mi Nexus 7 usando XDA Premium HD app
Click to expand...
Click to collapse
Bro, here is not your forum, here there arent any members with XS, why dont you try opening this thread in XS forum Q&A, that way you will get help from XS users.
Hi, today my phone went to the PROTECTED mode, and when I try to Autenticate, it says: "Wrong username or password", I've tried to use the PC Companion, and didn't work. I think this is happening because I had 3 Google Accounts. What can I do? HELP :crying:
Hi, have you search before you post ? I'm sure you find informations, too much tropic created foe this problem.
Envoyé de mon E2303 en utilisant Tapatalk
GITS-SAC said:
Hi, have you search before you post ? I'm sure you find informations, too much tropic created foe this problem.
Envoyé de mon E2303 en utilisant Tapatalk
Click to expand...
Click to collapse
The solutions of the other topics didn't wok
Your first attempt should be deleting extra Google accounts (not used for MyXperia) in the 20 secs before protection is activated. Then try to authenticate using Google.
If you tried to erase data from device using MyXperia, and Google device manager, after that, repaired your phone using PC Companion, and it did not work, phone is a brick and should be replaced by either local store or Sony.
Happened to me.
Sent from my E2363 using XDA Free mobile app
Hello
I tried to disable google apps on my redmi note 4 using shortcutmaker app now the phone is stuck on MI logo
My device is locked
can you please tell me how can i overcome this boot loop error
Try download or edl Mode.
Enviado do meu H60-L04 através de Tapatalk
Prolixo said:
Try download or edl Mode.
Enviado do meu H60-L04 através de Tapatalk
Click to expand...
Click to collapse
How can i get into edl mode, my device is locked .
i tried flashing with diy cable but when i release the button in cable, it says usb not recognized on pc
Got it fixed by flashing fastboot rom using DIY cable that i made myself
aaqib67 said:
Got it fixed by flashing fastboot rom using DIY cable that i made myself
Click to expand...
Click to collapse
hey ive got the same problem do you mind helping me i've tried to make a deep flash cable without succes :crying::crying:
donwalex said:
hey ive got the same problem do you mind helping me i've tried to make a deep flash cable without succes :crying::crying:
Click to expand...
Click to collapse
Bro i suggest you to go to service center if ur device is under warranty they will fix the issue in much better way rather than going with deep flash cables :silly:
donwalex said:
hey ive got the same problem do you mind helping me i've tried to make a deep flash cable without succes :crying::crying:
Click to expand...
Click to collapse
If the service Centre is available in your city then you should go there and they will fix it for you but if it's not available just like in my case then watch few videos on YouTube to make the deep flash cable and if you are too lazy to do it then Show the video to any electrician or someone who knows soldering. Good luck
hello
I'm sorry for my english.
My device was hardbrick while hwota was loading, it suddenly closed on 'install update packing' screen. It does not enter fastboot mode. It does not enter Recovery mode. usb seems to be in the device manager. the device does not open at all.
What rom were you trying to flash?
Sent from my ALP-L29 using Tapatalk
royhanks3 said:
What rom were you trying to flash?
Sent from my ALP-L29 using Tapatalk
Click to expand...
Click to collapse
C636-142 To c432-142
There's currently no way to fix it if it's in that state.
DevrimSeven60 said:
C636-142 To c432-142
Click to expand...
Click to collapse
Unfortunately, I think it's bricked for good "for now". Similar thing happened to my Mate 10 (non pro on 134 noxloader rom). Don't spend any money on DC tools to try and fix, right now it's unfixable.
Sent from my ALP-L29 using Tapatalk
DevrimSeven60 said:
hello
I'm sorry for my english.
My device was hardbrick while hwota was loading, it suddenly closed on 'install update packing' screen. It does not enter fastboot mode. It does not enter Recovery mode. usb seems to be in the device manager. the device does not open at all.
Click to expand...
Click to collapse
Hi good day.
I have been following your work from another page, and now in XDA.
I had not read your message, and, I changed the recovery for the stock, and, I was an idiot to close the bootloader.
What happened? Brick simple on my cell phone, did not come out (because I fixed it) of the image of erecovery (EMUI) without tabs or options, a rather rare image.
How do I solve it:
1. I did not enter fastboot, I did not correctly enter the stock recovery (I had deleted the twrp), I had closed the bootloader (my stupidity)
2. Be patient and wait for the battery to run out (wait a day for it).
3. Open cmd and place the command to open the bootloader (fastboot oem unlock) and execute.
4. Put the device in fastboot mode when connecting to the laptop (I did not work several times, the fastboot came out with error FUNC No 10 and NO 2), after numerous attempts and not to let it charge the battery too much (because it was restarted and towards brick in the EMUI logo), correctly enter the fastboot and unlock, when you enter step 3 automatically, it will be executed. I had an advance in removing the cell phone from the brick.
5. It reboots and wonderfully happened to the Rom (that had previously installed), that is to say, the erase was not executed when the bootloader had previously closed.
6. As I had little energy, it was turned off, but I connected it and entered charging mode without restarting (before I did it).
7. Wait for a load of at least 5%, and install the Catuva21 TWRP from the tutorial.
8. I put it by command to restart in fastboot, but I generate error (Error Func No 10 and No 2).
9. I turn off the cell phone and with volume up and power key
10. Enter the TWRP correctly, verify that it is installed.
11. Restart system and log in to the system. I had not deleted anything, but to avoid problems, I hope to load 55% and execute the steps to install the rom.
12. Enjoy and dry spilled tears.
Experience lived and I hope you do not do something that developers do not advise.
Gracias and happy day.
gaduarte7 said:
Hi good day.
I have been following your work from another page, and now in XDA.
I had not read your message, and, I changed the recovery for the stock, and, I was an idiot to close the bootloader.
What happened? Brick simple on my cell phone, did not come out (because I fixed it) of the image of erecovery (EMUI) without tabs or options, a rather rare image.
How do I solve it:
1. I did not enter fastboot, I did not correctly enter the stock recovery (I had deleted the twrp), I had closed the bootloader (my stupidity)
2. Be patient and wait for the battery to run out (wait a day for it).
3. Open cmd and place the command to open the bootloader (fastboot oem unlock) and execute.
4. Put the device in fastboot mode when connecting to the laptop (I did not work several times, the fastboot came out with error FUNC No 10 and NO 2), after numerous attempts and not to let it charge the battery too much (because it was restarted and towards brick in the EMUI logo), correctly enter the fastboot and unlock, when you enter step 3 automatically, it will be executed. I had an advance in removing the cell phone from the brick.
5. It reboots and wonderfully happened to the Rom (that had previously installed), that is to say, the erase was not executed when the bootloader had previously closed.
6. As I had little energy, it was turned off, but I connected it and entered charging mode without restarting (before I did it).
7. Wait for a load of at least 5%, and install the Catuva21 TWRP from the tutorial.
8. I put it by command to restart in fastboot, but I generate error (Error Func No 10 and No 2).
9. I turn off the cell phone and with volume up and power key
10. Enter the TWRP correctly, verify that it is installed.
11. Restart system and log in to the system. I had not deleted anything, but to avoid problems, I hope to load 55% and execute the steps to install the rom.
12. Enjoy and dry spilled tears.
Experience lived and I hope you do not do something that developers do not advise.
Gracias and happy day.
Click to expand...
Click to collapse
Did you have a hard brick on your device? I can not enter Fastboot, we are waiting for board software in China.
Try low battery, do it several times in a row, it has worked for me.
Have it connected to the PC, and with volume - and turn it off forcibly, and, let it restart. At some point you will successfully enter the fastboot, it is patience. Or, leave it to turn off, no load connect to the PC with volume -, and, repeat it until you manage to enter it, can be several times. It has happened to me three times.
I hope it helps you.
Good luck.
:fingers-crossed::fingers-crossed::laugh::laugh::good:
gaduarte7 said:
Try low battery, do it several times in a row, it has worked for me.
Have it connected to the PC, and with volume - and turn it off forcibly, and, let it restart. At some point you will successfully enter the fastboot, it is patience. Or, leave it to turn off, no load connect to the PC with volume -, and, repeat it until you manage to enter it, can be several times. It has happened to me three times.
I hope it helps you.
Good luck.
:fingers-crossed::fingers-crossed::laugh::laugh::good:
Click to expand...
Click to collapse
For Hardbrick, I think these methods will not be the solution.
but thanks.
I'm not sure what's wrong with my friends mate 10. It's stuck on the 4glte screen and the red light blinks. I'm not sure what's wrong or how to fix it. I can't get into fastboot or recovery or download mode.
Any help is appreciated. Thank you.
My problem is still going on. No board software for BLA-L29.
Has this S/W ever been released?
yfaykya said:
Has this S/W ever been released?
Click to expand...
Click to collapse
I did not understand. I have board software file for BLA.
I have a hard brick mate 10 pro. Kirin 970.
Can Funky huawei help me? I have board software but I can not load it.
http://i.hizliresim.com/WDZ3oQ.jpg
DevrimSeven60 said:
I have a hard brick mate 10 pro. Kirin 970.
Can Funky huawei help me? I have board software but I can not load it.
http://i.hizliresim.com/WDZ3oQ.jpg
Click to expand...
Click to collapse
No, FunkyHuawei won't be able to do anything for you unfortunately
Sent from my Mate 10 using Tapatalk
DevrimSeven60 said:
I have a hard brick mate 10 pro. Kirin 970.
Can Funky huawei help me? I have board software but I can not load it.
http://i.hizliresim.com/WDZ3oQ.jpg
Click to expand...
Click to collapse
Can you still access to the erecovery?
Sent from my HUAWEI BKL-L09 using XDA Labs
SADNESS
Hi guys, sorry English.
I'm from Brazil and I also gave a hard brick on my mate 10 pro, so I understood the new updates from May / 2018 could not be done through hwota.
I already did everything of phoenix does not work, I tried to make a cable dongle usb, also did not work.
now I can only cry because it is a device that cost a lot of money and has no solution.
MY original version is BLA-L09
BYE GUYS
felipecps said:
Hi guys, sorry English.
I'm from Brazil and I also gave a hard brick on my mate 10 pro, so I understood the new updates from May / 2018 could not be done through hwota.
I already did everything of phoenix does not work, I tried to make a cable dongle usb, also did not work.
now I can only cry because it is a device that cost a lot of money and has no solution.
MY original version is BLA-L09
Boa dia, eu tb sou do Brasil e estou na mesma situação sendo que o meu é BLA-L29
Click to expand...
Click to collapse
andre_ferreira said:
felipecps said:
Hi guys, sorry English.
I'm from Brazil and I also gave a hard brick on my mate 10 pro, so I understood the new updates from May / 2018 could not be done through hwota.
I already did everything of phoenix does not work, I tried to make a cable dongle usb, also did not work.
now I can only cry because it is a device that cost a lot of money and has no solution.
MY original version is BLA-L09
Boa dia, eu tb sou do Brasil e estou na mesma situação sendo que o meu é BLA-L29
Click to expand...
Click to collapse
Fala cara beleza?!
Nos ferramos, perdi 3 conto...acho que vai demorar muito pra resolver isso.
estava fazendo o rebrand para a nova versão e não sabia que estava brickando....coisa da huawei, agora o porque não sei.
Tentei dc phoenix e o easy firmware nenhum funciona, no site da funkyhuawei não tem solução pra esse brick de tela preta.
acho que ja era cara!!!
Click to expand...
Click to collapse
Guys, it's an English forum, so please keep it that way!
Redmi Note 4 SD Or Redmi Note 4X Suddenly Turned Off And Became Unresponsive.
The Device Is Not Responding to anything.
No Fastboot No Recovery Mode Nothing.
Just The Red Blinking ight Plz Help ...
And Also i Tried These
1.Opened The Phone and disconnected the battery and connected it again nothing happens
2.connected the phone to pc nothing happens no response of device being connected to the pc
3.also tried putting it to charge nothing happens just the annoying red blinking
and also if i disconnect the battery and then tried still nothing happens..
anybody plz help.....
agentliquid47 said:
Redmi Note 4 SD Or Redmi Note 4X Suddenly Turned Off And Became Unresponsive.
The Device Is Not Responding to anything.
No Fastboot No Recovery Mode Nothing.
Just The Red Blinking ight Plz Help ...
And Also i Tried These
1.Opened The Phone and disconnected the battery and connected it again nothing happens
2.connected the phone to pc nothing happens no response of device being connected to the pc
3.also tried putting it to charge nothing happens just the annoying red blinking
and also if i disconnect the battery and then tried still nothing happens..
anybody plz help.....
Click to expand...
Click to collapse
Does it respond when u connect it to pc ? I mean not on phone display but do u hear any connecting sound on pc?
I think your phone is in EDM mode, so connect the phone to the pc , download fastboot Rom and flash it via Xiaomi flash tool.
miteshladva said:
I think your phone is in EDM mode, so connect the phone to the pc , download fastboot Rom and flash it via Xiaomi flash tool.
Click to expand...
Click to collapse
nothing happens when connecting to pc
Dylan*123 said:
Does it respond when u connect it to pc ? I mean not on phone display but do u hear any connecting sound on pc?
Click to expand...
Click to collapse
no its doesn't respond only the red blinking light keeps blinking nothing else
agentliquid47 said:
no its doesn't respond only the red blinking light keeps blinking nothing else
Click to expand...
Click to collapse
U can try flashing fastboot stock rom it may work for u.
What were last changes or it was sudden?
Kindly also reply with other configuration on device.
IODroids said:
What were last changes or it was sudden?
Kindly also reply with other configuration on device.
Click to expand...
Click to collapse
my device is redmi note 4 sd 4gb ram variant with 64 gb storage
i had miui 10 global stable rooted with magisk and i was playing pubg vikendi map . phone just turn off suddenly battery percentage was approx 70 so no problem there . i have given it to service center i will update the thread once i get the info. but they think the power ic isn't working so ....not a software issue that is sure.......
agentliquid47 said:
my device is redmi note 4 sd 4gb ram variant with 64 gb storage
i had miui 10 global stable rooted with magisk and i was playing pubg vikendi map . phone just turn off suddenly battery percentage was approx 70 so no problem there . i have given it to service center i will update the thread once i get the info. but they think the power ic isn't working so ....not a software issue that is sure.......
Click to expand...
Click to collapse
I have also noticed the lagging in game after vikendi snow map in pubg in redmi note 4.I think something is wrong with update or only m the one facing this issue after updating ?
I got the same problem 2 month ago. I changed battery and bought an edl cable without any success
The Problem Was With Power IC No Battery Or Motherboard Problem But Xiaomi Care Said I Have To Replace Motherboard...So Suggest You Not To Go Xiaomi CC ...If Your Phone Is Out Of Warranty
agentliquid47 said:
The Problem Was With Power IC No Battery Or Motherboard Problem But Xiaomi Care Said I Have To Replace Motherboard...So Suggest You Not To Go Xiaomi CC ...If Your Phone Is Out Of Warranty
Click to expand...
Click to collapse
Ok
any solution? the same happens to me. the pc does not recognize me. I want to turn it on, and only the red light blink
A mi me pasa algo parecido, pero a mi si me reconoce Qualcomm HS-USB QDLoader 9008 (COM4) en test point. Sigo todos los pasos de los tutoriales pero me da error una y otra vez, llevo una semana intentándolo y no puedo. Unas veces me da este error "cannot receive hello packet" y otras "can not read from port COM4" y también
"se ha alcanzado el final del archivo. (0x80070026: Receiving hello packet", ya no se que hacer. En alguna ocasión me ha hecho el amago de empezar a flashear pero no lo ha hecho. He cambiado de roms .tgz, de xiaomiMiFlash y no hay manera.
Dylan*123 said:
Does it respond when u connect it to pc ? I mean not on phone display but do u hear any connecting sound on pc?
Click to expand...
Click to collapse
I have the same problem instead I didn't open it and remove the battery
but when i connect it to PC it give the sound that it is connected then that it is being disconnected but it didn't show up in my devices in PC