Hi Everyone, I got two Samsung SM-G920F and I googled my way here to update the FW to 6.0.1 on them to solve some problems they have.
I could upgrade the first one without any problems (and this solved the issues I had) using Odin and a firmware I got from sammobile, now the second one is failing after it starts the NAND write:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1101)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I've tried different FWs, the one that worked on the other SM-G920F was from United Arab Emirates, I've tried that one and one from Italy with the same results. The current installed version is G920FXXU2COH2.
Any help is really appreciated.
Thanks!!!
Related
i have a galaxy s 4 verizon i have mdk and i have tried unrooting it because my friend tried rooting it while i was gone and messed up the process but im using odin3.07 and im getting this. "Firmware upgrade encountered an issue. Please select recover mode in Kies & try again."
<ID:0/007> Removed!!
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> sbl1.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1
my phone says start [224,1440]
sw rev. check fail : fused 5, binary 1
and ive tried 2 other stock files and i still get the same thing i even tried a Me7 to please help
When you tried the me7 tat what happened
Sent from my Verizon Samsung Galaxy S4 with HD12 on Stock Side
Retired Phones / Devices
- Eris
- Droid 2
- Droid X
- Fascinate
- HP Touchpad
- Thunderbolt
- Droid Raxr
here are both mdk and me7 failures
jwoods82 said:
When you tried the me7 tat what happened
Sent from my Verizon Samsung Galaxy S4 with HD12 on Stock Side
Retired Phones / Devices
- Eris
- Droid 2
- Droid X
- Fascinate
- HP Touchpad
- Thunderbolt
- Droid Raxr
Click to expand...
Click to collapse
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> COMBINATION_I545VRUAME7_I545VZWAME7_690088_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> sbl1.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> aboot.mbn
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRUAMDK_NoWipe.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NON-HLOS.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> aboot.mbn
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Im using Odin v1.85
A1C_Malone said:
i have a galaxy s 4 verizon i have mdk and i have tried unrooting it because my friend tried rooting it while i was gone and messed up the process but im using odin3.07 and im getting this. "Firmware upgrade encountered an issue. Please select recover mode in Kies & try again."
<ID:0/007> Removed!!
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> sbl1.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1
my phone says start [224,1440]
sw rev. check fail : fused 5, binary 1
and ive tried 2 other stock files and i still get the same thing i even tried a Me7 to please help
Click to expand...
Click to collapse
"Fused:5" indicates that you're running a MJ7 bootloader.
If you can boot, check the bootloader revision. Otherwise, flash MJ7. Then de-friend that friend if you actually did start with MDK.
I had the same problem ...
i take an other usb cable (samsung of course) and try on another port on my pc
Hi,
I am trying to flash firmware BOG2 over BOC1 and I am consistently getting flash fail with the below error message.
I have changed the USB cable/port as well nothing works?Any help
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> R750XXU2BOG2_R750OXA2BOG2_R750XXU2BOG2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> dzImage
<ID:0/007> NAND Write Start!!
<ID:0/007> dzImage-recovery
<ID:0/007> sbl1.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/007> Added!!
<ID:0/007> Removed!!
rocky272727 said:
Hi,
I am trying to flash firmware BOG2 over BOC1 and I am consistently getting flash fail with the below error message.
I have changed the USB cable/port as well nothing works?Any help
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> R750XXU2BOG2_R750OXA2BOG2_R750XXU2BOG2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> dzImage
<ID:0/007> NAND Write Start!!
<ID:0/007> dzImage-recovery
<ID:0/007> sbl1.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/007> Added!!
<ID:0/007> Removed!!
Click to expand...
Click to collapse
I got pretty much the same error. As like you I have BOC and tried to flash BOG2.
Seems that bootloader is not recognized as compatible, no matter in fact it is. Seems modem is maybe different.
If anyone has any clue on how to workaround this issue, plz, let us know.
bump
Solved
andrew.mackew said:
I got pretty much the same error. As like you I have BOC and tried to flash BOG2.
Seems that bootloader is not recognized as compatible, no matter in fact it is. Seems modem is maybe different.
If anyone has any clue on how to workaround this issue, plz, let us know.
Click to expand...
Click to collapse
Hi,
I figured it out. BOG2 is a 2.2.1.4 and BOC1 is 2.2.1.5 (R750WVLU1BOC1), so downgrade not possible for bootloader.
rocky272727 said:
Hi,
I figured it out. BOG2 is a 2.2.1.4 and BOC1 is 2.2.1.5 (R750WVLU1BOC1), so downgrade not possible for bootloader.
Click to expand...
Click to collapse
Thanks for let me know that. Appreciate. :good:
same
well i got the same error , was trying to install cm on the watch then got stuck on samsung screen tried flashing the tizen firmware 4 files but everytime i end up with that thing do u know how to fix it ?!
Hello XDA,
I did brick my phone by trying to downgrade to 5.0.2 from 5.1.1 and bricked my phone and searching this forum I felt that there should be a post like this to ease the journey of people like me. As I did learn a lot from my 5 years android journey, I would like help everybody like me. Therefore if I find any important/"you may not know" fixes, I will share here with headings. Also If you have another solutions for any problems of these kind; please write here so I can collect em' all in the OP. Let's go!
-ODIN fail while flashing hidden.img-
Solution: This is caused because of your partition(pit). In XDA, you can find .pit files of S6 Edge for several models (i.e. I have a g925f so i have to find the corresponding pit file. The one worked for me was the G925F pit with Hidden_300M. First you flash this pit to your phone, then try to flash your rom; you're good to go!
Solution 2 Thanks to @Alex-V : Just delete the hidden.img from the rom.
---------------------------------------------------------------
-If you can't properly enter to recovery mode-
Solution: Please do the combo "Volume Down-Home-Power" until you reach download mode. When you reach there again do the same combo until the screen goes off. When it goes off QUICKLY switch to "Volume Up-Home-Power" combo and hold it until the screen comes in and dims a bit. When it dims release all buttons and ta-da you're in recovery mode.
---------------------------------------------------------------
-ODIN gives a fail at NAND write-
Solution: This problem is caused because of the nand mismatches (generally, or build differences etc.). Doing this may cause a hard-brick IF YOU DON'T follow the instructions CAREFULLY.
1) Get your device to download mode by using this combo "VolumeDown-Home-Power"
2) Open an UP TO DATE ODIN.
3) Find the corresponding .PIT file for your S6 EDGE.
4) Find the corresponding stock rom for your S6 EDGE.
5) Then put them into odin CORRECTLY. Rom to "AP", .pit to PIT
6) Make Sure these are checked: "Re-partition","NAND all erase"
7) Plug your device in and then press start.
After these you should be already flashed correctly without any nand write fail.
---------------------------------------------------------------
-SW REV CHECK FAIL DEVICE: 2 BINARY:1-
This happens when you try to downgrade from 5.1.1... Thanks to Samsung, we can not downgrade to repair our phones or save them because of the locked bootloader. So you have to flash to 5.1.1 again.
If anyone with a working rooted phone, can he/she share his/her own nand backup, so people with screwed boots can recover
or simple delete the hidden.img
Added to the post, thanks mate. Also looking for how to fix corrupted sdcard (theres no mmcblk0x file)
Hi,
I'm following your advice to try and overcome my S6 Edge's issue with failing to NAND write but I am still getting the same NAND write fail. I have another post detailing the issue here http://forum.xda-developers.com/showpost.php?p=67930722&postcount=5 if you want more info but I'll just post the Odin log here too just in case you can spot where I went wrong.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Erase...
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My device is an S6 Edge G925W8. Thanks.
Please Respond
Malganor said:
Hi,
I'm following your advice to try and overcome my S6 Edge's issue with failing to NAND write but I am still getting the same NAND write fail. I have another post detailing the issue here http://forum.xda-developers.com/showpost.php?p=67930722&postcount=5 if you want more info but I'll just post the Odin log here too just in case you can spot where I went wrong.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Erase...
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My device is an S6 Edge G925W8. Thanks.
Click to expand...
Click to collapse
I am also getting the exact same thing. I Put in the pit file like instructed as well as the correct rom... still get the same NAND WRITE START.
Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Erase...
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Every time I try to flash using Odin, it fails. Here's the log:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXS3DPB2_G925FOXE3DPAD_G925FXXS3DPB3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have a galaxy s6 edge, officially, the G925T version. But when I got a different custom ROM, the number changed to G925F. I've tried flashing the stock firmware for both those versions, and neither work. I have TWRP installed, so I wipe the system every time I try something new.
I've also tried it on multiple computers, on multiple USB ports, with multiple USB cables. And with different versions of Odin. Do you know what I'm doing wrong?
My Samsung Galaxy Grand Prime SM-G530H stuck in boot loop. So, I tried to install the new firmware by odin but i got this error massage
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G530HVJU1ANJ2_G530HZTM1ANJ2_G530HXXU1ANJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then, I downloaded new firmware and i got the new error
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G530HXXS2BPG1_G530HOLB2BPE3_G530HXXU2BPB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> tz.mbn
<ID:0/007> hyp.mbn
<ID:0/007> NON-HLOS.bin
<ID:0/007> sec.dat
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img.ext4
<ID:0/007> FAIL! (Erase)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Sorry for my bad english