To get a cm rom booting on vzw firmware heres what you must do.first you must flash us unlocked firmware.look for the thread to do this with.boot the phone.go back and flash dottat 1.85 ruu.let the rom boot.go into twrp do a full wipe format data flash cm rom gapps and your good to.how or why this works i have no idea but with helping my friend @andybones we discovered this is the method for it to work.happy Flashing!!!
Possible to make this in bullet or number/step format and a little more clear and detailed? Pretty sure I get it, but... Thanks!
Detailed Guide
UPDATE: please read this posthttps://forum.xda-developers.com/showpost.php?p=71137922&postcount=866
With thanks to @The Fer-Shiz-Nizzle it was figured out that the key to getting LOS/AOSP ROMs booted was rfg_3.img. Verizon and Sprint don't have one. Instead of having to flash the entire US Unlocked RUU (which flashes the firmware, thus flashing the rfg_3.img) you can now simply 'flash' just the 1 .img
This post has a .zip I made and instructions to flash rfg_3.img
https://forum.xda-developers.com/showpost.php?p=71362727&postcount=32
---UPDATED 6/02/17---
OUTDATED - I SUGGEST FOLLOWING THE ABOVE INSTEAD
Here is a more clear, step-by-step guide.
1) Flash the US Unlocked firmware, modified for Verizon.
1a) Here is the one I personally used, that is already modified.
1b) CAUTION - Flashing this did wipe my internal, so back up everything! Back up everything either way.. even if you're just reading this.
1c) How to flash?
Code:
adb reboot bootloader
fastboot oem rebootRUU
fastboot flash zip 1.96.617.20_Modified4VZW.zip
fastboot reboot
2) After you issue the 'fastboot reboot' command you will most likely get stuck on the hTC splash screen as the modified firmware wiped everything, including your system (ROM). If it didn't, not a problem - reboot the device to download mode and continue onto step 3.
2a) Hold Vol+ Vol- and Power buttons until the phone reboots. Keep holding Vol- while letting go of the other buttons. This will bring you to download mode.
3) Now flash the Official Verizon 1.85.605.8 RUU from dottat. Putting you back to a full Verizon variant device. Thread found here.
3a) Let the RUU boot fully up to the stock ROM after the installation finishes.
3b) Make sure to have the AOSP ROM of your choice either on SD-Card or move it now onto the Internal storage.
4) Set your device back to your liking. Splash screen, etc.. but also now you flash TWRP.
4a) If you use multirom, I would still first finish these steps, then you can flash the multirom TWRP and zip. (I am using multirom successfully with both Stock Verizon 1.85.605.8 ROM as primary and CM, AOKP and Resurrection Remix AOSP ROMs as secondaries while being fully Verizon variant device, thanks to this process)
5) Boot to TWRP. Do a full wipe and flash your AOSP ROM.
5a) Note - Most the AOSP ROMs (possibly all that are out?) will boot to the boot animation and then go to a black screen for a minute or so, don't freak. This is normal behavior and will resume back to the boot animation.
6) Enjoy! Hit thanks button if this helped you.
andybones said:
Here is a more clear, step-by-step guide.
1) Flash the US Unlocked firmware, modified for Verizon.
1a) Here is the one I personally used, that is already modified.
1b) CAUTION - Flashing this did wipe my internal, so back up everything! Back up everything either way.. even if you're just reading this.
1c) How to flash?
Code:
adb reboot bootloader
fastboot oem rebootRUU
fastboot flash zip 1.96.617.20_Modified4VZW.zip
fastboot reboot
2) After you issue the 'fastboot reboot' command you will most likely get stuck on the hTC splash screen as the modified firmware wiped everything, including your system (ROM). If it didn't, not a problem - reboot the device to download mode and continue onto step 3.
2a) Hold Vol+ Vol- and Power buttons until the phone reboots. Keep holding Vol- while letting go of the other buttons. This will bring you to download mode.
3) Now flash the Official Verizon 1.85.605.8 RUU from dottat. Putting you back to a full Verizon variant device. Thread found here.
3a) Let the RUU boot fully up to the stock ROM after the installation finishes.
3b) Make sure to have the AOSP ROM of your choice either on SD-Card or move it now onto the Internal storage.
4) Set your device back to your liking. Splash screen, etc.. but also now you flash TWRP.
4a) If you use multirom, I would still first finish these steps, then you can flash the multirom TWRP and zip. (I am using multirom successfully with both Stock Verizon 1.85.605.8 ROM as primary and CM, AOKP and Resurrection Remix AOSP ROMs as secondaries while being fully Verizon variant device, thanks to this process)
5) Boot to TWRP. Do a full wipe and flash your AOSP ROM.
5a) Note - Most the AOSP ROMs (possibly all that are out?) will boot to the boot animation and then go to a black screen for a minute or so, don't freak. This is normal behavior and will resume back to the boot animation.
6) Enjoy! Be baffled like myself as to why this worked. Also hit thanks button if this helped you.
Click to expand...
Click to collapse
Thanks man was just about to write it up.you saved me the trouble lol.
hovercraftdriver said:
Possible to make this in bullet or number/step format and a little more clear and detailed? Pretty sure I get it, but... Thanks!
Click to expand...
Click to collapse
Made a more clear guide, if you haven't already got it.
This will serve as a thread for those needing help as well. :good:
gillim74 said:
Thanks man was just about to write it up.you saved me the trouble lol.
Click to expand...
Click to collapse
- team effort. :highfive:
andybones said:
Made a more clear guide, if you haven't already got it.
This will serve as a thread for those needing help as well. :good:
- team effort. :highfive:
Click to expand...
Click to collapse
Indeed
HELP HELP! Guys I'm STUCKED
andybones said:
Here is a more clear, step-by-step guide.
1) Flash the US Unlocked firmware, modified for Verizon.
1a) Here is the one I personally used, that is already modified.
1b) CAUTION - Flashing this did wipe my internal, so back up everything! Back up everything either way.. even if you're just reading this.
1c) How to flash?
Code:
adb reboot bootloader
fastboot oem rebootRUU
fastboot flash zip 1.96.617.20_Modified4VZW.zip
fastboot reboot
2) After you issue the 'fastboot reboot' command you will most likely get stuck on the hTC splash screen as the modified firmware wiped everything, including your system (ROM). If it didn't, not a problem - reboot the device to download mode and continue onto step 3.
2a) Hold Vol+ Vol- and Power buttons until the phone reboots. Keep holding Vol- while letting go of the other buttons. This will bring you to download mode.
3) Now flash the Official Verizon 1.85.605.8 RUU from dottat. Putting you back to a full Verizon variant device. Thread found here.
3a) Let the RUU boot fully up to the stock ROM after the installation finishes.
3b) Make sure to have the AOSP ROM of your choice either on SD-Card or move it now onto the Internal storage.
4) Set your device back to your liking. Splash screen, etc.. but also now you flash TWRP.
4a) If you use multirom, I would still first finish these steps, then you can flash the multirom TWRP and zip. (I am using multirom successfully with both Stock Verizon 1.85.605.8 ROM as primary and CM, AOKP and Resurrection Remix AOSP ROMs as secondaries while being fully Verizon variant device, thanks to this process)
5) Boot to TWRP. Do a full wipe and flash your AOSP ROM.
5a) Note - Most the AOSP ROMs (possibly all that are out?) will boot to the boot animation and then go to a black screen for a minute or so, don't freak. This is normal behavior and will resume back to the boot animation.
6) Enjoy! Be baffled like myself as to why this worked. Also hit thanks button if this helped you.
Click to expand...
Click to collapse
Guys I really need help with this thread.
What I expected this was like I will be able to flash the custom rom and change from Verizon variant to run viper, but I ended up with the same stock rom from Verizon.
My verizon htc 10 is still S-ON and Locked Bootloader and according to what I've read threads and forums I found out that I can't unlock the bootloader unless I pay 25$ to use SunShine App. So I was so interested with this thread and I've followed the procedures from step 1 until step 3 when everything back to stock and I realized that I was in the same stock rom as I used to be nothing change or make it worth it after I flashed the RUU.exe something like that.
Then through step 4 I stucked there! I have no idea what to do next maybe I'm just dumb and can't get rid of the problems? Please let me know what to do next :\
sorry for my bad english cuz I'm so hesitating!!!!:crying:
cheakimpor said:
Guys I really need help with this thread.
What I expected this was like I will be able to flash the custom rom and change from Verizon variant to run viper, but I ended up with the same stock rom from Verizon.
My verizon htc 10 is still S-ON and Locked Bootloader and according to what I've read threads and forums I found out that I can't unlock the bootloader unless I pay 25$ to use SunShine App. So I was so interested with this thread and I've followed the procedures from step 1 until step 3 when everything back to stock and I realized that I was in the same stock rom as I used to be nothing change or make it worth it after I flashed the RUU.exe something like that.
Then through step 4 I stucked there! I have no idea what to do next maybe I'm just dumb and can't get rid of the problems? Please let me know what to do next :\
sorry for my bad english cuz I'm so hesitating!!!!:crying:
Click to expand...
Click to collapse
What..?
please read the thread title again. And did you even read my steps outlined before doing them? You're lucky you didn't brick your device being S-ON...
andybones said:
Here is a more clear, step-by-step guide.
1) Flash the US Unlocked firmware, modified for Verizon.
1a) Here is the one I personally used, that is already modified.
1b) CAUTION - Flashing this did wipe my internal, so back up everything! Back up everything either way.. even if you're just reading this.
1c) How to flash?
Code:
adb reboot bootloader
fastboot oem rebootRUU
fastboot flash zip 1.96.617.20_Modified4VZW.zip
fastboot reboot
2) After you issue the 'fastboot reboot' command you will most likely get stuck on the hTC splash screen as the modified firmware wiped everything, including your system (ROM). If it didn't, not a problem - reboot the device to download mode and continue onto step 3.
2a) Hold Vol+ Vol- and Power buttons until the phone reboots. Keep holding Vol- while letting go of the other buttons. This will bring you to download mode.
3) Now flash the Official Verizon 1.85.605.8 RUU from dottat. Putting you back to a full Verizon variant device. Thread found here.
3a) Let the RUU boot fully up to the stock ROM after the installation finishes.
3b) Make sure to have the AOSP ROM of your choice either on SD-Card or move it now onto the Internal storage.
4) Set your device back to your liking. Splash screen, etc.. but also now you flash TWRP.
4a) If you use multirom, I would still first finish these steps, then you can flash the multirom TWRP and zip. (I am using multirom successfully with both Stock Verizon 1.85.605.8 ROM as primary and CM, AOKP and Resurrection Remix AOSP ROMs as secondaries while being fully Verizon variant device, thanks to this process)
5) Boot to TWRP. Do a full wipe and flash your AOSP ROM.
5a) Note - Most the AOSP ROMs (possibly all that are out?) will boot to the boot animation and then go to a black screen for a minute or so, don't freak. This is normal behavior and will resume back to the boot animation.
6) Enjoy! Be baffled like myself as to why this worked. Also hit thanks button if this helped you.
Click to expand...
Click to collapse
Hi, thanks for this post. I've flashed this custom unlocked firmware, then flashed the stock Verizon one over-top of it. Now, since I'm a noob, will this leave the radio working? Because before I've had many issues with custom roms and the radio not working on this phone. I have S-Off and an Unlocked bootloader. (Im VERY new if you cannot tell.)
I had the stock rom rooted, and then switched to Viper10.
All went to **** when I switched to ICE. Signal was GONE.
kiwigramme said:
Hi, thanks for this post. I've flashed this custom unlocked firmware, then flashed the stock Verizon one over-top of it. Now, since I'm a noob, will this leave the radio working? Because before I've had many issues with custom roms and the radio not working on this phone. I have S-Off and an Unlocked bootloader. (Im VERY new if you cannot tell.)
I had the stock rom rooted, and then switched to Viper10.
All went to **** when I switched to ICE. Signal was GONE.
Click to expand...
Click to collapse
Flashing the Verizon RUU indeed does flash the Verizon radio. Google what an RUU is for better understanding.
andybones said:
Flashing the Verizon RUU indeed does flash the Verizon radio. Google what an RUU is for better understanding.
Click to expand...
Click to collapse
Thank you, I'm more asking for a better understanding of how this decryption thing works with disabling the radio. There is very very little information online. Am I selecting the wrong options in TWRP or simply flashing the wrong roms?
kiwigramme said:
Thank you, I'm more asking for a better understanding of how this decryption thing works with disabling the radio. There is very very little information online. Am I selecting the wrong options in TWRP or simply flashing the wrong roms?
Click to expand...
Click to collapse
I'm not sure what you're doing wrong as I don't know what you did....
You are on MM firmware. You are a Verizon user. There is no benefit to flash any other firmware like the Android N US Unlocked firmware. No benefit.
The ONLY reason I flashed it, and this thread was made because of this discovery, that for some reason, the simple steps of
1) flash us unlocked firmware
2) flash vzw ruu
3) flash twrp
4) flash cm rom
5) profit
That's it. That's what this thread is for. I am not sure about radio, and decryption stuff, you are better off asking in a thread dedicated to that, or even creating one.. if you have these questions -- so do others.
For some info that I can give (which will be short as on phone)..
step 2, you flash the vzw ruu, which means you are back to 100% stock VZW MM ROM. You CAN flash N ROMs, but again this thread is not for that. When you flash the ROM, like Leedroid N, ICE N, Viper N, for ex. they have option in aroma for MM or N, you choose MM. As for radio, read the ROM threads instructions, I think Viper has them on their site, in-fact here.
http://venomroms.com/viper10-downloads/?refresh=true
read. ask questions. learn. repeat.
Hope this was of some help. :good:
P.S. When they say format data, it is not WIPE data. it is FORMAT data. you need to actually type YES in TWRP. You may need to do this. Personally... since I am using multirom, I am on Verizon MM RUU, I did these steps so I can run CM. As long as I have my stock deodexed MM ROM as my primary I can run N ROMs no issue as secondary (if you are familiar with multirom) I have the stock rom as primary, Leedroid N, ICE N and CM 14.1 ROMs all as secondary ROMs running great.
andybones said:
Flash the US Unlocked firmware, modified for Verizon.
Click to expand...
Click to collapse
What do I do to "modify it for Sprint"?
mcwups1 said:
What do I do to "modify it for Sprint"?
Click to expand...
Click to collapse
Please sit tight.
mcwups1 said:
What do I do to "modify it for Sprint"?
Click to expand...
Click to collapse
Been very busy, wasn't ignoring you.
Edit the android-info.txt with the CID and MID for Sprint. If you need help with that let me know. Follow the rest of the instructions, but flash the Sprint RUU rather Verizon, and the rest should be the same.
Merry Christmas
andybones said:
Been very busy, wasn't ignoring you.
Edit the android-info.txt with the CID and MID for Sprint. If you need help with that let me know. Follow the rest of the instructions, but flash the Sprint RUU rather Verizon, and the rest should be the same.
Merry Christmas
Click to expand...
Click to collapse
Beautiful!
I will try this very soon!
Sorry, I didn't see this, or get a notification.
---------- Post added at 04:21 PM ---------- Previous post was at 04:16 PM ----------
andybones said:
Been very busy, wasn't ignoring you.
Edit the android-info.txt with the CID and MID for Sprint. If you need help with that let me know. Follow the rest of the instructions, but flash the Sprint RUU rather Verizon, and the rest should be the same.
Merry Christmas
Click to expand...
Click to collapse
Also, if I have Super CID, I change to 11111111?
mcwups1 said:
Beautiful!
I will try this very soon!
Sorry, I didn't see this, or get a notification.
---------- Post added at 04:21 PM ---------- Previous post was at 04:16 PM ----------
Also, if I have Super CID, I change to 11111111?
Click to expand...
Click to collapse
If your device is SuperCID you can actually leave it as VZW_001, or change it to Sprints (being SuperCID though allows you to flash basically anything, so continue to be careful). I am not 100% sure if it matter about MID, that was one thing I was unsure about, but if you open up a Sprint firmware and look at the android.info.txt, change modelid: 2PS650000 to whatever it is for Sprint (it may be the same?). but other than that you are good to go!
Sorry it took me so long, I didn't foresee anything bad happening but I wanted to be sure first.
andybones said:
If your device is SuperCID you can actually leave it as VZW_001, or change it to Sprints (being SuperCID though allows you to flash basically anything, so continue to be careful). I am not 100% sure if it matter about MID, that was one thing I was unsure about, but if you open up a Sprint firmware and look at the android.info.txt, change modelid: 2PS650000 to whatever it is for Sprint (it may be the same?). but other than that you are good to go!
Sorry it took me so long, I don't foresee anything bad happening but I wanted to be sure first.
Click to expand...
Click to collapse
2PS640000 for Sprint.
Now, I'm just worried about it working!
Sprint has had several MM RUU's.
I might be the first to try this with Sprint's latest update.
mcwups1 said:
2PS640000 for Sprint.
Now, I'm just worried about it working!
Sprint has had several MM RUU's.
I might be the first to try this with Sprint's latest update.
Click to expand...
Click to collapse
RUU is an RUU, I wouldn't worry. And if are flash older RUU, then the new firmware, but that's going outside the guide and can't say that the AOSP ROMs will boot after the firmware, but I don't see why not.
Or do you mean flashing the US unlocked firmware on Sprints new firmware? If so you can flash an older RUU/firmware, then the edited US unlocked firmware, then Sprint newest RUU.
figured id just flash this and get it out of the way in case I wanted to run some of these asop builds popping up along the way.
from my understanding from reading this is that its kinda a permament fix, meaning id never have to flash the modified firmware pack again even if I reflash a ruu a second time down the road, or even the Verizon N update say? or is it needed again after doing that?
Related
Before I begin, Mods, PLEASE pin this. I (when I was a noob) had absolute difficulty installing ROMs. This is very noob-friendly, fixes Status 7 errors, and is easy to follow.
Alright friends and future flashers. I used to have difficulty installing ROMs. Now that I know how (after going through numerous tutorials), I'd like to make it easy for ALL of you. Enjoy your Custom ROM!
Before beginning, you need Android's SDK,Flashtool and The latest Official firmware.
If ever your phone needs to install drivers, let it install, don't unplug the phone or whatever.
And, battery at least 30%. Mine does it at even 20% without issues, but just to be safe.
Step 1: Revert to Stock
You don't need to downgrade. After flashing the latest stock kernel, I have flashed every single GB and ICS ROM in existence without issues, so you don't need to flash a specific one. But, latest one tends to be more stable. Here's what you do:
Get the latest Global ftf for your phone. Then, flash it using Flashtool. I won't go into specifics, but PM me if needed
By Now, you should have a stock EVERYTHING. Boot up the phone, run through the whole set up process. Once you are done, you need to get your IMEI number. Do this by following the steps here.
In the end, you should have the bootloader unlocked. If you come up with something like bootloader already unlocked, then you are good to go. Now onto......
Step 2: Preparing your Flash.
Download the ROM of your choice. I'd recommend FXP's Unofficial CyanogenMod9 as it has the best stability and no ICS Multitouch issues. If it is GB, any ROM will do. Most of them are stable.
Now, in the case of CyanogenMod, they often come with their own custom Kernel. It is in the zip file, known as boot.img, and you simply extract it to your platform-tools folder in the android-sdk folder you downloaded to unlock the bootloader. This is also true for some MIUI ROMs I've come across. Read their forum posts for more info on which kernel to use.
Copy the ZIP file to your sdcard. It does not have to be the root of SDcard, anywhere will do.
By the end, your Custom ROM's ZIP file will be in your SDCard, and the kernel file (a.k.a. boot.img or whatever_the _kernel_name_is.img) will be here:
32bit Windows: C:/Program Files/Android/android-sdk/platform-tools
64bit Windows: C:/Program Files(x86)/Android/android-sdk/platform-tools
Now we can
Step 3: Flash your Custom ROM
In the folder above (depending on OS version) press Shift+RightClick. Options will show up. Select "Open Command Prompt Here". A Command Prompt will open (duh).
Turn off your phone. Wait 10 seconds. While plugging in your phone, press the Menu button (the Right button). The LED Indicator should turn blue. This shows your in fastboot mode. If it starts to boot, rip out the battery and try again. DON'T STOP PRESSING UNTIL IT TURNS BLUE.
Now, type EXACTLY AS FOLLOWS, ONE AT A TIME. Just type in the lines with the "-" before it, but don't put in the "-" when typing it. The line underneath in brackets is an explanation, so you understand what is happening.
-fastboot devices
(This is actually a quick test I do to see if my phone is connected in flash mode or not. If nothing happens, it is not in flash mode or the drivers are installing)
-fastboot flash boot boot.img
(This is telling fastboot to FLASH the BOOT partition of your phone with the file specified. If you are using a different kernel, simply replace boot.img with the name of the kernel, ending with .img and wait for it to finish. Won't take long)
-fastboot reboot
(This causes the phone to reboot)
Now, while it is starting up, keep repeatedly pressing the Volume Down button until you are in ClockWorkMod Recovery (Assuming you are using it. CWM is the most popular and most kernels use it) Then, If you choose to, make a backup. I personally don't, as it is not too big an issue and I never revert to an old ROM anyway.
After that, choose Factory Reset. This will remove ALL data in your phone except your Stock ROM. Then, Clear Cache. You might've noticed it already did that when you Factory Reset, but this is for safety. Finally, in advanced, Wipe Dalvik-Cache and Wipe Battery Stats. I do this all the time for safety.
Now, the fun bit. GO to Install ZIP from SDCard. Select Choose ZIP, find your ROMs ZIP file, and install. It might take awhile, but not too long. Just be patient. When it finishes, flash anything else the ROMs forum post says to flash (Gapps, Patch, etc) and select Reboot Phone.
Step 4: Done!
Your phone will start up. First time is always slow, but this WILL WORK. Congratulations. You now have a Custom ROM
If you get a Status 7 error while flashing a ROM, reboot recovery and wipe everything again. If that doesn't work, flash official firmware and try again.
Credits to:
-Google: Providing Android SDK and Gapps
-Androxyde: Flashtool
-Madfysh: List of Official ICS ROMs
FXP: Creating CyanagonMod9
-And YOU!
P.S.: If you're confused, or feel this could use something extra PM me.
And uh, if it needs to be moved, please do so. Thanks!
I do know there is THIS but I felt some of his steps were unnecessary. Example, rooting. Any custom ROM will be rooted, so there will be no need to worry about that. And he also provided overclocking tips and an unofficial bootloader unlock which are hazardous and potentially permadamaging to the phone.
PLEASE Don't spoil the mood man!!
This is a development section where even Noob Devs know how to flash a Custom Rom!! PLeaseee Pleaseeee ... Move it
Alright man. How would I move it? Cause, I only RECENTLY started being active on the forums.
Jass5991 said:
I do know there is THIS but I felt some of his steps were unnecessary. Example, rooting. Any custom ROM will be rooted, so there will be no need to worry about that. And he also provided overclocking tips and an unofficial bootloader unlock which are hazardous and potentially permadamaging to the phone.
Click to expand...
Click to collapse
Don't say that thread is unnecessary; they put everything in one thread cause it's easy to find. the first step we should do is rooting if we are noops. Then we will be curious about unlock or custom rom later.
Sent from Xperia Neo using AOKP B40
Still dev thread so if you don't know how you should not be trying
It goes like this no dl link no thread
but still is a good post
some unnecessary parts
some dodgy parts
But good for noob never-ending Questions
Maybe Q&A
Reck1993 said:
Don't say that thread is unnecessary; they put everything in one thread cause it's easy to find. the first step we should do is rooting if we are noops. Then we will be curious about unlock or custom rom later.
Sent from Xperia Neo using AOKP B40
Click to expand...
Click to collapse
Okay. I will add an easy rooting instructions to it.
kormatoes said:
Still dev thread so if you don't know how you should not be trying
It goes like this no dl link no thread
but still is a good post
some unnecessary parts
some dodgy parts
But good for noob never-ending Questions
Maybe Q&A
Click to expand...
Click to collapse
Thanks kormatoes. Could you gimme some of the unnecessary/dodgy parts?
Jass5991 said:
I do know there is THIS but I felt some of his steps were unnecessary. Example, rooting. Any custom ROM will be rooted, so there will be no need to worry about that. And he also provided overclocking tips and an unofficial bootloader unlock which are hazardous and potentially permadamaging to the phone.
Click to expand...
Click to collapse
1) actually that(which you linked) tutorial is good, it just need some updating. but your tutorial is different than that.
2) root is certainly not unnecessary! not all people will go for custom roms, specially as most of them are for unlocked BL.
3) unofficial unlock is not hazardous, it is tricky, but it paid of if we look on the advantage against official unlock
Nice from you that you wrote all this, it's based only for custom roms's, thread which is already sticked is for basic things, which any noob should know.
But still, this looks kinda cluttered, and from noob(which you intend this to) point of view, to long/complicate to read
Madfysh said:
1) actually that(which you linked) tutorial is good, it just need some updating. but your tutorial is different than that.
2) root is certainly not unnecessary! not all people will go for custom roms, specially as most of them are for unlocked BL.
3) unofficial unlock is not hazardous, it is tricky, but it paid of if we look on the advantage against official unlock
Nice from you that you wrote all this, it's based only for custom roms's, thread which is already sticked is for basic things, which any noob should know.
But still, this looks kinda cluttered, and from noob(which you intend this to) point of view, to long/complicate to read
Click to expand...
Click to collapse
Thank you all big guns
but there should be a start-up kit for newbie
There can be a Starter Section with due permission
lalit387 said:
Thank you all big guns
but there should be a start-up kit for newbie
There can be a Starter Section with due permission
Click to expand...
Click to collapse
As it is, I am attempting to code a batch file to automatically run the entire flashing process, including kernel and ROM. Having a small issue where it does not wipe dalvik and cache. It also doesn't flash the custom ROM
Can anyone tell me where to get my At One M8 repairs?
I can't take it to AT&T since they will say it's been tampered. I would appreciate any advice because I couldn't get any ROM into it. Only cyanogen would work but no WiFi.
ricm68 said:
Can anyone tell me where to get my At One M8 repairs?
I can't take it to AT&T since they will say it's been tampered. I would appreciate any advice because I couldn't get any ROM into it. Only cyanogen would work but no WiFi.
Click to expand...
Click to collapse
Not enough information. What about it is "broken" requiring repair? In what way is it "tampered"?
Oh, and HTC will most likely refuse to repair it directly, telling you that if you bought it from AT&T, that AT&T needs to act as the agent for repair. You can always try to head over to HTC's website (I'm sure you can find it), find the support section, and make a support inquiry from them directly.
garyd9 said:
Not enough information. What about it is "broken" requiring repair? In what way is it "tampered"?
Oh, and HTC will most likely refuse to repair it directly, telling you that if you bought it from AT&T, that AT&T needs to act as the agent for repair. You can always try to head over to HTC's website (I'm sure you can find it), find the support section, and make a support inquiry from them directly.
Click to expand...
Click to collapse
Well I don't know how but I erased the internal memory completely and now it won't take any roms. No matter what I try in recovery it always fails. The only thing I can install is cyanogenmod. There is no wifi also.
i'll try to go to at&t or htc. I hope they don;t charge me too much to repair.
Thanks.
ricm68 said:
Well I don't know how but I erased the internal memory completely and now it won't take any roms. No matter what I try in recovery it always fails. The only thing I can install is cyanogenmod. There is no wifi also.
i'll try to go to at&t or htc. I hope they don;t charge me too much to repair.
Thanks.
Click to expand...
Click to collapse
Did you flash the google play edition ruu? If so, the phone was repartitioned, and sense will no longer "fit" on the system partition. There's a way to deal with that if that's the case...
garyd9 said:
Did you flash the google play edition ruu? If so, the phone was repartitioned, and sense will no longer "fit" on the system partition. There's a way to deal with that if that's the case...
Click to expand...
Click to collapse
I flashed the one found at the post: [RUU] att ruu 1.58.502.1 posted
Hmm.. Not sure what to suggest in that case. I'm not very familiar with the whole RUU thing myself...
Sent from my Nexus 7 using Tapatalk
Download the ota update. Extract the firmware.zip from it but don't extract firmware.zip. boot to fastboot.
Fastboot oem rebootRUU
Fastboot flash zip firmware.zip
Do it again
Fastboot flash zip firmware.zip
Fastboot reboot-bootloader
Fastboot flash recovery twrp.img
Fastboot erase cache
Load recovery
Wipe, advanced wipe
Select dalvik, cache, data, system, internal. Wipe.
Put Rom on ext sd card or
Adb push Rom.zip /sdcard/
Install zip this will obviously erase everything on your phone.
Click thanks.
Sent from my HTC One_M8 using XDA Premium 4 mobile app
ricm68 said:
Well I don't know how but I erased the internal memory completely and now it won't take any roms. No matter what I try in recovery it always fails. The only thing I can install is cyanogenmod. There is no wifi also.
i'll try to go to at&t or htc. I hope they don;t charge me too much to repair.
Thanks.
Click to expand...
Click to collapse
You don't need to repair. You just need to troubleshoot. You are throwing the baby out with the bath water, if you go for a hardware repair for what is likely a software issue that is easy to resolve.
You also need to provide more details, and be specific as possible. Namely:
What recovery and version number?
S-on or off?
What exactly have you tried to flash?
Did you factory reset in bootloader?
Do you have working adb?
What happened when you ran the RUU?
Hi redpoint73, I have twrp 2.7.1.0, unlocked, s-off.And I have adb.
I tried to ruu, then install a recovery, a stock rom and don't know how many things more and can't bring it back. They told me I should install cwm and try from there but don't know how. Please advice me on what to do and if you can, guide me step by step.
Thanks so much for your help.
ricm68 said:
Hi redpoint73, I have twrp 2.7.1.0, unlocked, s-off.And I have adb.
I tried to ruu, then install a recovery, a stock rom and don't know how many things more and can't bring it back. They told me I should install cwm and try from there but don't know how. Please advice me on what to do and if you can, guide me step by step.
Thanks so much for your help.
Click to expand...
Click to collapse
http://forum.xda-developers.com/htc-one-m8/general/vomerguides-m8-bootldr-unlock-s-off-t2800727
You wont need the whole thing but some of it might pertain to you
ricm68 said:
Hi redpoint73, I have twrp 2.7.1.0, unlocked, s-off.And I have adb.
I tried to ruu, then install a recovery, a stock rom and don't know how many things more and can't bring it back.
Click to expand...
Click to collapse
I've already asked what happened when you ran the RUU, and you didn't answer. Any error messages, etc.? This is very critical information, so its hard to help when you don't provide the answers requested (especially this one).
RUU is meant to recover the device in most cases. So if it didn't work, its very posible you have a fundamental USB connectivity issue. What response do you get when you type the adb command:
adb devices
What happens when you try to install recovery or a stock ROM? You need to give more information and specifics if you really want help.
And "don't know how many things" is not meaningful information. You need to list all the things you tried, and the results. Again, the lack of specific info makes it hard to help. I literally typed more asking you questions, than you bothered typing the answers. This does not bode well if you really want help.
You did not even answer all the questions I asked:
- What exactly have you tried to flash? (list the ROMs)
- Did you factory reset in bootloader?
ricm68 said:
They told me I should install cwm and try from there but don't know how. Please advice me on what to do and if you can, guide me step by step.
Click to expand...
Click to collapse
Who is "they"? Again, you are being too vague.
I am personally more familiar with TWRP, so I would advise staying with that if you want help from me. Nothing against CWM. But again, its just what I'm more familiar with.
redpoint73 said:
I've already asked what happened when you ran the RUU, and you didn't answer. Any error messages, etc.? This is very critical information, so its hard to help when you don't provide the answers requested (especially this one).
RUU is meant to recover the device in most cases. So if it didn't work, its very posible you have a fundamental USB connectivity issue. What response do you get when you type the adb command:
adb devices
What happens when you try to install recovery or a stock ROM? You need to give more information and specifics if you really want help.
And "don't know how many things" is not meaningful information. You need to list all the things you tried, and the results. Again, the lack of specific info makes it hard to help. I literally typed more asking you questions, than you bothered typing the answers. This does not bode well if you really want help.
You did not even answer all the questions I asked:
- What exactly have you tried to flash? (list the ROMs)
- Did you factory reset in bootloader?
Who is "they"? Again, you are being too vague.
I am personally more familiar with TWRP, so I would advise staying with that if you want help from me. Nothing against CWM. But again, its just what I'm more familiar with.
Click to expand...
Click to collapse
I Hi, thanks a lot. I did the factory reset from bootloader and tried to install Android_Revolution_HD-One_M8_5.0 and after doing the process it returns failed. Also One_M8_1.54.401.10_odexed and Jmz_M8_StockRootedOdex-ATT and I just tried with cyanogenmod 11. While I installed this in twrp recovery it said failed but when I reboo0ted in stared loading. I installed gapps and now my phone is working at least. But I still can't flash a snse rom or a gpe rom because it fails in twrp.
That's about all I can tell you. Oh, and I see it's in android 4.4.4.
ricm68 said:
I Hi, thanks a lot. I did the factory reset from bootloader and tried to install Android_Revolution_HD-One_M8_5.0 and after doing the process it returns failed. Also One_M8_1.54.401.10_odexed and Jmz_M8_StockRootedOdex-ATT and I just tried with cyanogenmod 11. While I installed this in twrp recovery it said failed but when I reboo0ted in stared loading. I installed gapps and now my phone is working at least. But I still can't flash a snse rom or a gpe rom because it fails in twrp.
That's about all I can tell you. Oh, and I see it's in android 4.4.4.
Click to expand...
Click to collapse
I don't understand how its so difficult for you to answer the basic questions I've asked multiple times now What happens when you run the RUU?
The RUU should restore the phone to full functionality, albeit with stock recovery, no root, etc. (if that is what you want).
Of course, this is not ideal if you want to install custom ROMs (which I assume is the case).
What I would try is to re-install TWRP. I'm not aware of any bugs in the newest version (which it appears you have) that would prevent flashing all the ROMs you mentioned. So maybe its just an improper install:
Re-download the latest TWRP img file. Place file in your fastboot folder. Open command prompt (navigate to the fastboot folder) and type:
fastboot erase cache
fastboot flash recovery "filename.img"
(where "filename.img" is the actual file name of the TWRP img file, with no quotes)
From there, load a ROM to your device, boot into TWRP and try flashing the ROM.
---------- Post added at 04:09 PM ---------- Previous post was at 03:10 PM ----------
Also, it is becoming apparent to me that doing a factory reset in bootloader corrupts the internal memory. My advice is to never do this (factory reset within the OS settings or in recovery if you need to).
But if the internal memory was corrupt, you shouldn't be able to load any files onto the phone (including ROMs). It seems that your internal memory is ok (you can transfer files to the phone, access them, etc)?
redpoint73 said:
I don't understand how its so difficult for you to answer the basic questions I've asked multiple times now What happens when you run the RUU?
The RUU should restore the phone to full functionality, albeit with stock recovery, no root, etc. (if that is what you want).
Of course, this is not ideal if you want to install custom ROMs (which I assume is the case).
What I would try is to re-install TWRP. I'm not aware of any bugs in the newest version (which it appears you have) that would prevent flashing all the ROMs you mentioned. So maybe its just an improper install:
Re-download the latest TWRP img file. Place file in your fastboot folder. Open command prompt (navigate to the fastboot folder) and type:
fastboot erase cache
fastboot flash recovery "filename.img"
(where "filename.img" is the actual file name of the TWRP img file, with no quotes)
From there, load a ROM to your device, boot into TWRP and try flashing the ROM.
---------- Post added at 04:09 PM ---------- Previous post was at 03:10 PM ----------
Also, it is becoming apparent to me that doing a factory reset in bootloader corrupts the internal memory. My advice is to never do this (factory reset within the OS settings or in recovery if you need to).
But if the internal memory was corrupt, you shouldn't be able to load any files onto the phone (including ROMs). It seems that your internal memory is ok (you can transfer files to the phone, access them, etc)?
Click to expand...
Click to collapse
The phone was working ok but suddenly wifi wouldn't turn on and mobile network stopped again!!!
I tried to intall android revolution but when it gets to installing the apps is says "set_perm: some changes failed". I click next and reboot and it just takes me back to recovery
redpoint73 said:
I don't understand how its so difficult for you to answer the basic questions I've asked multiple times now What happens when you run the RUU?
The RUU should restore the phone to full functionality, albeit with stock recovery, no root, etc. (if that is what you want).
Of course, this is not ideal if you want to install custom ROMs (which I assume is the case).
What I would try is to re-install TWRP. I'm not aware of any bugs in the newest version (which it appears you have) that would prevent flashing all the ROMs you mentioned. So maybe its just an improper install:
Re-download the latest TWRP img file. Place file in your fastboot folder. Open command prompt (navigate to the fastboot folder) and type:
fastboot erase cache
fastboot flash recovery "filename.img"
(where "filename.img" is the actual file name of the TWRP img file, with no quotes)
From there, load a ROM to your device, boot into TWRP and try flashing the ROM.
---------- Post added at 04:09 PM ---------- Previous post was at 03:10 PM ----------
Also, it is becoming apparent to me that doing a factory reset in bootloader corrupts the internal memory. My advice is to never do this (factory reset within the OS settings or in recovery if you need to).
But if the internal memory was corrupt, you shouldn't be able to load any files onto the phone (including ROMs). It seems that your internal memory is ok (you can transfer files to the phone, access them, etc)?
Click to expand...
Click to collapse
I did the factory reset from within cyanogenmod and it didn't wipe it. It restarted back to cyanogenmod. I copied andoid revolution to my internal memory and try to install from there.
ricm68 said:
The phone was working ok but suddenly wifi wouldn't turn on and mobile network stopped again!!!
I tried to intall android revolution but when it gets to installing the apps is says "set_perm: some changes failed". I click next and reboot and it just takes me back to recovery
Click to expand...
Click to collapse
You need to try the things I've suggested. I've made some definitive recommendations, and you seem to have ignored them. Honestly, I don't see a point in trying to help anymore, if you don't read what I'm taking the time to post; or you don't try what I've suggested.
Worst case is RUU and start over (install custom recovery again, etc.). But again, I have no idea what happened when you tried to RUU since you still haven't answered that.
You aren't going to make any progress, if you keep ignoring the advice that is given to you.
I'm doing what you told me!!!
I reinstalled twrp and tried but it failed again. Believe me, I've been doing what you suggested.
Can you please give me the steps to RUU and what ruu file to download and use. I really appreciate all you're doing for me and the time you are taking to help.
Sent from my One M8 using XDA Premium 4 mobile app
I was able to install cyanogen mod again and I am using the phone but I want to install sense again.
Sent from my One M8 using XDA Premium 4 mobile app
Hello everyone!
I've been very happy with my rooted M9 for the last few months but now a system update message on my screen and I'm trying to figure out what to do about. I seem to recall when I rooted my phone that there could be complications if I install a system update on a rooted phone (like making a Nandroid Backup) but I'm finding scarce information on the topic. Does anyone here have some advice about this?
Rom...
http://forum.xda-developers.com/showthread.php?t=3083799
Firmware...
http://forum.xda-developers.com/showthread.php?t=3073355
Follow the second link above.
You will need to restore the factory system.img using TWRP (exFAT or NTFS for external USB as file is > 4GB).
This puts the modified system (root) back to stock so the update will run successfully.
Flash the original recovery for you system version too.
Then you can accept the OTA and then root the phone again.
Thanks for the responses! I'm still uncertain about a few things so tell me if I have this right.
First I need to restore the factory image. Is that a guy named OJM is talking about on this thread? (http://forum.xda-developers.com/sprint-one-m9/general/rooting-guide-t3073004)
To restore your clean system backup to accept OTAs, you must use fastboot. If you are S-ON, you must be in download mode.
-copy your clean system.emmc.win to your adb/fastboot folder on your pc
-boot into download mode
-use cmd fastboot flash system system.emmc.win
Click to expand...
Click to collapse
In that case, what is a system.emmc.win?
Then I flash the original recovery...what are you refering to when you say "original recovery"?
After that my phone should be locked again and I can go to that second link, download the latest firmware and flash it. And then I can unlock and root my phone again.
Edit: So it looks like someone has made a guide on how to get the OTA updates (if you use the right words in your search). It looks no one done anything with it since May so maybe it still works? http://forum.xda-developers.com/one-m9/general/best-unlocking-bootloader-rooting-guide-t3087354
I would just run the official RUU, it's a one shot process will take care of everything including the radios. Much easier than messing around, just make sure you are S-OFF before you do it. When it's done just flash the latest TWRP and install your rom you will be done.
Sim-X said:
I would just run the official RUU, it's a one shot process will take care of everything including the radios. Much easier than messing around, just make sure you are S-OFF before you do it. When it's done just flash the latest TWRP and install your rom you will be done.
Click to expand...
Click to collapse
That was what I ended up doing. Had few bumps on the way but I managed to get everything working. Thanks for the help everyone!
RUU
Sim-X said:
I would just run the official RUU, it's a one shot process will take care of everything including the radios. Much easier than messing around, just make sure you are S-OFF before you do it. When it's done just flash the latest TWRP and install your rom you will be done.
Click to expand...
Click to collapse
hi sim I have a question the only thing I got to make sure is that the phone is S-OFF and nothing will happen because I read that also the bootlooder had to be lock again so I'm not sure
Hello guys,
I have a problem with my OnePlus X, and it would be lovely if I could get some help or advice from you guys.
> To provide some slight background, I purchased this off of eBay to complete my OnePlus collection. Most listings were above what OnePlus originally sold the phone for, but I found one for $125 in good condition by a seller with a good rating. It was advertised as soft-bricked, with Fastboot in working order. I thought "no problem, I'll just reflash it and be on my merry way."
Now onto the issue. I received it, charged it up, and attempted flashing the official recovery provided by OnePlus, but something is not working. I've been tinkering with Android for a number of years now, so I troubleshooted as much as I could, but to no avail.
1. Starting with device unplugged and powered off, boot into fastboot
2. Plugged into the computer, and ran `fastboot devices` to ensure it's recognized. After that, I flashed the recovery.img that was on my desktop with `fastboot flash recovery recovery.img` (yes I was in the correct directory). It looked successful. Picture of cmd response text at the following imgur album: /a/25DEQ (sorry I cannot post full links yet, had to create a new xda profile, forgot my old one :/
3. Unplugged the phone, powered off, Volume Down + Power to attempt boot into recovery. Failure. It just turns on with the 1+ logo, and quickly flashes the 'android' logo at the bottom. It stays like this until I manually power off.
I'm a bit stumped I have to admit. I would greatly appreciate any input you folks have. Thank you.
AndriyEtch said:
Hello guys,
I have a problem with my OnePlus X, and it would be lovely if I could get some help or advice from you guys.
> To provide some slight background, I purchased this off of eBay to complete my OnePlus collection. Most listings were above what OnePlus originally sold the phone for, but I found one for $125 in good condition by a seller with a good rating. It was advertised as soft-bricked, with Fastboot in working order. I thought "no problem, I'll just reflash it and be on my merry way."
Now onto the issue. I received it, charged it up, and attempted flashing the official recovery provided by OnePlus, but something is not working. I've been tinkering with Android for a number of years now, so I troubleshooted as much as I could, but to no avail.
1. Starting with device unplugged and powered off, boot into fastboot
2. Plugged into the computer, and ran `fastboot devices` to ensure it's recognized. After that, I flashed the recovery.img that was on my desktop with `fastboot flash recovery recovery.img` (yes I was in the correct directory). It looked successful. Picture of cmd response text at the following imgur album: /a/25DEQ (sorry I cannot post full links yet, had to create a new xda profile, forgot my old one :/
3. Unplugged the phone, powered off, Volume Down + Power to attempt boot into recovery. Failure. It just turns on with the 1+ logo, and quickly flashes the 'android' logo at the bottom. It stays like this until I manually power off.
I'm a bit stumped I have to admit. I would greatly appreciate any input you folks have. Thank you.
Click to expand...
Click to collapse
Which recovery u tried? Did u knOw the previous os version details?
And try this after flashing recovery in fastboot, boot into it directly by giving a cmd "fastboot boot recovery.img"
cva_kabil said:
Which recovery u tried? Did u knOw the previous os version details?
And try this after flashing recovery in fastboot, boot into it directly by giving a cmd "fastboot boot recovery.img"
Click to expand...
Click to collapse
Hi! Thank you for your reply
I posted this same question on the /r/oneplus subreddit, and received a quick and helpful walkthrough. Turns out part of the problem was that the micro-usb port on the phone itself is a bit unreliable. I haven't investigated too deeply, but it took a while to find a position for the wire to maintain a stable connection. I suspect this may be why the device was bricked in the first place (disconnect when flashing rom/kernel/etc.)
Anyways, for some reason flashing the stock recovery to the phone was just not working. The guy on reddit recommended trying TWRP, and that worked immediately. However, at that point, I had no idea what the history of the phone was or what OS was on it before, what firmware it had. I tried installing the official CM13 and then Sultan's CM13 with no luck. What *did* work was Oxygen OS 2.2.6.
At this point I'm stuck yet again though... The Marshmallow OTA (3.1.3) in the OS shows as available for download, but when I try to install the download only gets to 22% and then stops. Flashing the 3.1.3 OTA.zip available on OnePlus' support site doesn't work in TWRP, and when I try to flash stock recovery, it doesn't work.. don't know what else to try.
AndriyEtch said:
Hi! Thank you for your reply
I posted this same question on the /r/oneplus subreddit, and received a quick and helpful walkthrough. Turns out part of the problem was that the micro-usb port on the phone itself is a bit unreliable. I haven't investigated too deeply, but it took a while to find a position for the wire to maintain a stable connection. I suspect this may be why the device was bricked in the first place (disconnect when flashing rom/kernel/etc.)
Anyways, for some reason flashing the stock recovery to the phone was just not working. The guy on reddit recommended trying TWRP, and that worked immediately. However, at that point, I had no idea what the history of the phone was or what OS was on it before, what firmware it had. I tried installing the official CM13 and then Sultan's CM13 with no luck. What *did* work was Oxygen OS 2.2.6.
At this point I'm stuck yet again though... The Marshmallow OTA (3.1.3) in the OS shows as available for download, but when I try to install the download only gets to 22% and then stops. Flashing the 3.1.3 OTA.zip available on OnePlus' support site doesn't work in TWRP, and when I try to flash stock recovery, it doesn't work.. don't know what else to try.
Click to expand...
Click to collapse
Root your device using twrp or kingoroot method then install flashify and try to flash stock recovery using flashify. .. Tht may work.
Flashing 3.1.3 via official twrp ll not work... Cos ur bootloader version, U can do it only with stock recovery or u need to edit meta data file. Or u can flash stock recovery img file by twrp
cva_kabil said:
Root your device using twrp or kingoroot method then install flashify and try to flash stock recovery using flashify. .. Tht may work.
Flashing 3.1.3 via official twrp ll not work... Cos ur bootloader version, U can do it only with stock recovery or u need to edit meta data file. Or u can flash stock recovery img file by twrp
Click to expand...
Click to collapse
Thanks I'll give those a shot once I'm home from work! Quick question about editing the META INF. I've heard that doing so risks hard-bricking the device. Is that true?
AndriyEtch said:
Thanks I'll give those a shot once I'm home from work! Quick question about editing the META INF. I've heard that doing so risks hard-bricking the device. Is that true?
Click to expand...
Click to collapse
I dont think so... I hv not tried... But as of i know if u edit it wrongly, u will not be able to flash that file. . Try others methods first... Hope it works
AndriyEtch said:
Thanks I'll give those a shot once I'm home from work! Quick question about editing the META INF. I've heard that doing so risks hard-bricking the device. Is that true?
Click to expand...
Click to collapse
Hi OP, sorry for joining late to the party
So the thing is the OnePlus X is at opposites now since the official MM release on 29th September. The thing is if you are running the old bootloader (OxygenOS 2.x.x) or any ROM based on it, then the New TWRP will not boot, neither will the Stock Recovery that is hosted on the OnePlus download section for the X, which is where i assume you download the stock recovery from, right ? Also note that the official recovery hosted on the TWRP website is also yet to be updated, we're working on that.
So you are on the old Bootloader. Simple stuff. I have posted my guide a lot of time around the forums, its gained a lot of merit. You could follow it for your update process. I'll leave a link below. In case you wanna verify that the old bootloader is causing the issue my Index Thread pinned in the general section has a link for the Stock recovery for Old bootloader, try flashing that via fastboot, if it successfully boots then you're set.
Comprehensive guide to Update to Marshmallow Bootloader
The above guide is centered to the thread i have posted it on but the process is 99% the same. In the end, you could just stay with Oxygen OS 3.1.3, or flash any custom ROM based on the new Bootloader.
Now regarding your query about editing the META of the ROM, well Yes to an extent it IS risky if you ain't careful because my guide guides you to delete the one single line that removes the device check, so as long as you use the modified zip on OnePlus X only, there will be no issues.
Let me know for any further clarifications, also you're welcome to join our support group on Telegram, all of our developers are active there. Ping me (@ mellogang_unite) for an invite
Hello everyone this is my fist guide so be kind with the formatting, i will get better as I post more. I am writing this guide, because like you, the reader, I had installed lineageOS 14.1 and set up the phone and realized there was encryption on it, and with that tried to wipe it in twrp just to find out that it only wiped the encryption key, but not the encryption itself. Don't panic, it isn't all your fault, XD. Stay calm, the last thing you need is to be freaking out, flashing random zips in hopes of fixing it. I will give credit to all of the developers whose tools i am linking at the bottom.
Now that the introductions are out of the way, time for the complimentary dose of warning.
WARNING: Doing this won't guarantee that this will fix it, as every situation can vary. I am not responsible for any bricked devices, thermal reactors coming from your phone after this, or modding before it was cool.
Assuming you can still get into fastboot first you need to gather these files if you don't have them yet.
- Minimal adb and fastboot on windows after installing just drag to desktop to add files to it
- Qualcomm fastboot drivers for axon7tool.exe and for fastboot and adb
- TWRP 3.0.4-1 official for Axon 7
- B29 rollback modded zip on the second tab
- Nougat modem and bootstack
- Tenfar's axon7root.exe (just in case you can't use fastboot. that's what i used because i don't know how to use axon7tool.exe)
- Fastboot image to get fastboot working again flash it in twrp after getting twrp installed again through axon7root.exe
- Some time because this will likely take an hour of your time, assuming you have the drivers and files already downloaded, longer if not and slow internet.
- LineageOS 14.1
- GAPPS 7.1.1 ARM 64
- almost forgot, you also need a microsd card to store the files because we will be wiping your entire internal with this, so back up your lovely dank memes or forever hold the loss.
Step 0.5. if you don't have fastboot working flash the bootloader unlock file by drakenfx to get it working again. if you don't have twrp for whatever reason go to the guide for axon7root.exe linked above and reboot to edl mode by holding all buttons down and have your phone connected to computer to know you are there. there won't be a vibration to let you know, just your computer telling you it has a connected device. now flash twrp, by first renaming the recovery to recovery.img and putting it in the adb folder along with the the root exe and do 'axon7root.exe -p (insert your com number listed in device manager) -r' (without the ' obviously) and it should send the recovery. if it doesn't see your device. make sure you have the drivers installed and make sure you have put down your com number where i left the () at
Step 1. assuming your device boots to this beautiful screen. you need to go back to twrp and drag the B29 zip from your computer to your external sd card from mtp and go to mount and mount system read-only this is very important.
Step 2. flash the B29 modded and let it go through. this will take a few minutes. if the progress bar automatically jumps to the end, you didn't go read only.
Step 3. after it finishes reboot into system and let it set up your system, you can skip through because we will be resetting again anyhow.
Step 4. reboot back to recovery. you can do this by using that pesky bl unlocked message by pressing up on volume as soon as it shows and selecting recovery. there you can see you have stock recovery, don't panic this is what we need. select wipe data factory reset and let it do it
Step 5. go back and skip set up again and reboot to bootloader where you can now 'fastboot flash recovery recovery.img' to get back twrp.
Step 6. flash the nougat bootstack and modem i had you download. after flashing that, go to wipe: Advanced wipe. Select Dalvik, system, data, cache and swipe to wipe. this will format it as ext4 which is what is required to get to lineageOS
Step 7. flash lineageos 14.1 and your gapps category and wait to let it finish. Note, you don't have to flash the modem more than once after flashing lineageos, even for updating. just after leaving B29
Step 8. reboot to make sure your encryption problem is not there
Step 9. set up phone and profit.
If you have done everything right, you shouldn't have bricked and should be back to lineageos 14.1 with no further problems. If you skipped around and got yourself bricked, congratulations because i am not the best at fixing problems, and i can try to help, but you will be at the mercy of the Best devs this community has to offer.
Now to the part where I thank all the Devs who, without their tireless time and effort, would not have made this guide possible and development into this phone in the first place. @Unjustified Dev for the lineageOS build i use as my daily driver for now; you rock dude. ^^
@DrakenFX oh god where do i begin. for the bl unlock zip, B29 modded ota, inspiration to the rest of the community, etc.
@tenfar for the axon7root.exe tool used
@sixohtew for his constant help and advice with not only this guide, but with teaching me to build android. if you are interest in learning how to compile android for any device, he can probably help. he has a very fair deal and is amazing at what he does.
Thank you all for your copious hours of time spent in the building of each great tool and to the community as a whole. Everyone, these guys are amazing, even if i have only talked to one of them. Be sure to stop by and donate.
If i have left anyone's name out, please hit me up and i will add you to the credits, and to that i apologize.
Happy flashing!
I read through your guide several times. I'm missing the point here. At which step does the decryption get removed?
gpz1100 said:
I read through your guide several times. I'm missing the point here. At which step does the decryption get removed?
Click to expand...
Click to collapse
Sorry for delayed response, it gets removed when you do the factory reset in stock recovery. For some reason TWRP can't remove it from /data in nougat but stock recovery can in B29.
Wipe->Format Data in TWRP removes all encryption from /data and /sdcard. Did you try that before reinstalling the stock recovery? I've had weird experiences in the past with stuck encryption.
QuantumFluxx said:
Wipe->Format Data in TWRP removes all encryption from /data and /sdcard. Did you try that before reinstalling the stock recovery? I've had weird experiences in the past with stuck encryption.
Click to expand...
Click to collapse
I did try it. It doesn't wipe it because there is a bug with TWRP for our phone. I would wipe and even format data and it wouldn't work. If you go to the official TWRP thread it even warns you that if you have encryption to not wipe. We had a dev who wiped and it got rid of the encryption key and not the encryption, like what happened to me. I tried to wipe so many times and had to revert. Long process but I got my phone to work again
Rip me
So I was bricked to the point where I was able to access TWRP and if I flashed any ROM, even after formatting data, I would reach a Decryption unsuccessful screen on my A2017U. I followed the guide from step 0.5, since fastboot was not working. After flashing the bootloader unlock file via TWRP, I was not able to access anything, further bricking the device. It boots within a second to a black screen, and reboots to it if I hold the power button or any combination for recovery.etc. I can not go to EDL mode; Axon7tool detects it though when it is in this state, and is able to send files successfully. However, it still stays in this black screen. Is there any way to get back to a functioning phone at this point?
Edit: It is apparently always in EDL? It shows up and is identified by my PC as QUSB_BULK...
navsterama said:
So I was bricked to the point where I was able to access TWRP and if I flashed any ROM, even after formatting data, I would reach a Decryption unsuccessful screen on my A2017U. I followed the guide from step 0.5, since fastboot was not working. After flashing the bootloader unlock file via TWRP, I was not able to access anything, further bricking the device. It boots within a second to a black screen, and reboots to it if I hold the power button or any combination for recovery.etc. I can not go to EDL mode; Axon7tool detects it though when it is in this state, and is able to send files successfully. However, it still stays in this black screen. Is there any way to get back to a functioning phone at this point?
Edit: It is apparently always in EDL? It shows up and is identified by my PC as QUSB_BULK...
Click to expand...
Click to collapse
Can you still get into recovery with power & vol+? and what happened as soon as you flashed the zip?
twilighttony said:
Can you still get into recovery with power & vol+? and what happened as soon as you flashed the zip?
Click to expand...
Click to collapse
Nope :crying:. The EDL combo and the recovery combo result in the same screen and duration of boot. After flashing the bootloader unlock file, I remember reading the script to see that it was successful and yielded a result of 1 before resulting in this screen.
navsterama said:
Nope :crying:. The EDL combo and the recovery combo result in the same screen and duration of boot. After flashing the bootloader unlock file, I remember reading the script to see that it was successful and yielded a result of 1 before resulting in this screen.
Click to expand...
Click to collapse
I am not sure what happened to that, were you originally on B15? i was simply on the modem/bootstack which allowed me to succeed in flashing that file. that could be a variable. i will be sure to look into a tool ive heard of called miflash which works through edl mode to unbrick.
navsterama said:
Nope :crying:. The EDL combo and the recovery combo result in the same screen and duration of boot. After flashing the bootloader unlock file, I remember reading the script to see that it was successful and yielded a result of 1 before resulting in this screen.
Click to expand...
Click to collapse
try this.
twilighttony said:
I am not sure what happened to that, were you originally on B15? i was simply on the modem/bootstack which allowed me to succeed in flashing that file. that could be a variable. i will be sure to look into a tool ive heard of called miflash which works through edl mode to unbrick.
Click to expand...
Click to collapse
Yea, I was on B15. Trying miFlash right now though. I'll update you when its done...:good:
navsterama said:
Yea, I was on B15. Trying miFlash right now though. I'll update you when its done...:good:
Click to expand...
Click to collapse
ok that does make sense as to why it failed. i was on the modded modem file that allowed me to install los
twilighttony said:
ok that does make sense as to why it failed. i was on the modded modem file that allowed me to install los
Click to expand...
Click to collapse
Wait...in terms of the bootstack I was also on the modded one for LOS 14.1. However, it was when the last unofficial build came out (Feb 3rd???). I tried to clean flash LOS Weekly today and thats when I ran into the dilemma of the decryption. Idk why I said yes for being on B15, for some reason that translated to generally Nougat bootstack in my head. My bad, OP.
---------- Post added at 10:47 PM ---------- Previous post was at 10:30 PM ----------
navsterama said:
Yea, I was on B15. Trying miFlash right now though. I'll update you when its done...:good:
Click to expand...
Click to collapse
Unbricked, booted up, now its on the "beautiful" screen. Thanks!
twilighttony said:
try this.
Click to expand...
Click to collapse
This is posted in the dev section. No need for external linkage.
navsterama said:
Wait...in terms of the bootstack I was also on the modded one for LOS 14.1. However, it was when the last unofficial build came out (Feb 3rd???). I tried to clean flash LOS Weekly today and thats when I ran into the dilemma of the decryption. Idk why I said yes for being on B15, for some reason that translated to generally Nougat bootstack in my head. My bad, OP.
---------- Post added at 10:47 PM ---------- Previous post was at 10:30 PM ----------
Unbricked, booted up, now its on the "beautiful" screen. Thanks!
Click to expand...
Click to collapse
glad that worked. perhaps i will edit the guide to where fastboot is added at the end as an extra. seems that if we at least have twrp we can go from there. do you still have an unlocked bl?
lafester said:
This is posted in the dev section. No need for external linkage.
Click to expand...
Click to collapse
will remember for future reference. thanks
lafester said:
This is posted in the dev section. No need for external linkage.
Click to expand...
Click to collapse
At least the poster of the blog gives credit to the original author and thread.
The method referenced at the blog is confusing though. If one is in a bricked state (edl only), they can't access developer options or even boot into android.
gpz1100 said:
At least the poster of the blog gives credit to the original author and thread.
The method referenced at the blog is confusing though. If one is in a bricked state (edl only), they can't access developer options or even boot into android.
Click to expand...
Click to collapse
If you are in edl only with an unlocked bootloader than the part of enabling bl unlock won't apply.
twilighttony said:
If you are in edl only with an unlocked bootloader than the part of enabling bl unlock won't apply.
Click to expand...
Click to collapse
Right, I understand that, but the person reading your blog won't, and thus the confusion.
This guide really needs to be stickied or higher up. Restarted my phone yesterday and it randomly got encrypted upon booting. Was locked out of everything and no keyboard was popping up to be able to put in a PIN or Password. This guide saved me. Thank you.