My Moto E has been dead.......
It doesnt power up at all.....When i press POWER + VOLDOWN together nothing happens and When i do it while plugged in the notification led blinks once......and when plugged into pc it shows "RELINK HS-USB QDLoader 9008 (COM3)"....The pc plays the connected sound periodically every 1 or 2 mins with notification light blinking,.
It happened when i wanted to update from cm13 to cm14.1...i updated my TWRP to 3.0.2 Successfully. Then I Wiped to Factory and installed cm14.1 Successfully...eventually When i tried installing Open Gaaps it failed showing not sufficient storage space......
Then I tried formatting internal SD and also wanted to format external SD but was unable. It gave me error that "ext-sd is in unknown file system" inorder to format this I tried formatting using "fastboot format external_sd" in fastboot....It gave me error 'unable to format raw partition"....then after googling I got to know that I had used External SD as internal in cm13 and so twrp was unable to format ext-sd....
Then i created partition using twrp in external sd..and then using advance wipe wiped data , internal storage, cache , dalvik cache, ext3-sd(or whatever it is), external storage....and it was successful.........and so i rebooted to recovery and after it is just dead........
i tried blankflash.bat but its giving error "
.C:\Users\Admin\Desktop\blankflash\blankflash>.\qboot.exe blank-flash
opening device: \\.\COM3
OKAY [ -0.000s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x3964945
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.016s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.000s]
validating files
OKAY [ 0.000s]
switching to download mode
OKAY [ 0.016s]
greeting device for image downloading
OKAY [ 0.000s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\Users\Admin\Desktop\blankflash\blankflash>pause
Press any key to continue . . "
Then i read in one of the forum that blankflash is for moto G device..
I had a look at this but didnt got anything http://forum.xda-developers.com/moto-e/general/unbricking-hard-bricked-moto-e-t3306809
I aslo found this Guide : (Unbrick Qualcomm mobiles with Step-by-step guide)... but in this guide the phone is showing : "Qualcomm HS-USB QDLoader 9008" and my device is showing : "RELINK HS-USB QDLoader 9008" so what should i do???
Pls help me unbrick this device coz i dont have any money for service center (₹500 & ₹1000 denomination banned )
Hope this is correct section to post this thread
tejeshjadhav.tj said:
My Moto E has been dead.......
It doesnt power up at all.....When i press POWER + VOLDOWN together nothing happens and When i do it while plugged in the notification led blinks once......and when plugged into pc it shows "RELINK HS-USB QDLoader 9008 (COM3)"....The pc plays the connected sound periodically every 1 or 2 mins with notification light blinking,.
It happened when i wanted to update from cm13 to cm14.1...i updated my TWRP to 3.0.2 Successfully. Then I Wiped to Factory and installed cm14.1 Successfully...eventually When i tried installing Open Gaaps it failed showing not sufficient storage space......
Then I tried formatting internal SD and also wanted to format external SD but was unable. It gave me error that "ext-sd is in unknown file system" inorder to format this I tried formatting using "fastboot format external_sd" in fastboot....It gave me error 'unable to format raw partition"....then after googling I got to know that I had used External SD as internal in cm13 and so twrp was unable to format ext-sd....
Then i created partition using twrp in external sd..and then using advance wipe wiped data , internal storage, cache , dalvik cache, ext3-sd(or whatever it is), external storage....and it was successful.........and so i rebooted to recovery and after it is just dead........
i tried blankflash.bat but its giving error "
.C:\Users\Admin\Desktop\blankflash\blankflash>.\qboot.exe blank-flash
opening device: \.\COM3
OKAY [ -0.000s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x3964945
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.016s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.000s]
validating files
OKAY [ 0.000s]
switching to download mode
OKAY [ 0.016s]
greeting device for image downloading
OKAY [ 0.000s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\Users\Admin\Desktop\blankflash\blankflash>pause
Press any key to continue . . "
Then i read in one of the forum that blankflash is for moto G device..
I had a look at this but didnt got anything http://forum.xda-developers.com/moto-e/general/unbricking-hard-bricked-moto-e-t3306809
I aslo found this Guide : (Unbrick Qualcomm mobiles with Step-by-step guide)... but in this guide the phone is showing : "Qualcomm HS-USB QDLoader 9008" and my device is showing : "RELINK HS-USB QDLoader 9008" so what should i do???
Pls help me unbrick this device coz i dont have any money for service center (₹500 & ₹1000 denomination banned )
Hope this is correct section to post this thread
Click to expand...
Click to collapse
Yeah pls help me I am stuck at same problem...
Even I have a dead moto e
Pls give a solution
Same here
Devs pls give a legit solution
This happened to my phone while updating OTA
This happened 1 month ago......still no solution ?
Even mine's dead. Help needed.
tejeshjadhav.tj said:
my moto e has been dead.......
It doesnt power up at all.....when i press power + voldown together nothing happens and when i do it while plugged in the notification led blinks once......and when plugged into pc it shows "relink hs-usb qdloader 9008 (com3)"....the pc plays the connected sound periodically every 1 or 2 mins with notification light blinking,.
It happened when i wanted to update from cm13 to cm14.1...i updated my twrp to 3.0.2 successfully. Then i wiped to factory and installed cm14.1 successfully...eventually when i tried installing open gaaps it failed showing not sufficient storage space......
Then i tried formatting internal sd and also wanted to format external sd but was unable. It gave me error that "ext-sd is in unknown file system" inorder to format this i tried formatting using "fastboot format external_sd" in fastboot....it gave me error 'unable to format raw partition"....then after googling i got to know that i had used external sd as internal in cm13 and so twrp was unable to format ext-sd....
Then i created partition using twrp in external sd..and then using advance wipe wiped data , internal storage, cache , dalvik cache, ext3-sd(or whatever it is), external storage....and it was successful.........and so i rebooted to recovery and after it is just dead........
I tried blankflash.bat but its giving error "
.c:\users\admin\desktop\blankflash\blankflash>.\qboot.exe blank-flash
opening device: \\.\com3
okay [ -0.000s]
greeting device for command mode
okay [ -0.000s]
identifying device
...serial = 0x3964945
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
okay [ 0.016s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
okay [ 0.000s]
validating files
okay [ 0.000s]
switching to download mode
okay [ 0.016s]
greeting device for image downloading
okay [ 0.000s]
sending programmer
okay [ 0.016s]
flashing singleimage
failed (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
c:\users\admin\desktop\blankflash\blankflash>pause
press any key to continue . . "
then i read in one of the forum that blankflash is for moto g device..
I had a look at this but didnt got anything http://forum.xda-developers.com/moto-e/general/unbricking-hard-bricked-moto-e-t3306809
i aslo found this guide : (unbrick qualcomm mobiles with step-by-step guide)... But in this guide the phone is showing : "qualcomm hs-usb qdloader 9008" and my device is showing : "relink hs-usb qdloader 9008" so what should i do???
Pls help me unbrick this device coz i dont have any money for service center (₹500 & ₹1000 denomination banned )
hope this is correct section to post this thread
Click to expand...
Click to collapse
my moto e is dead since the past 3 days. Was flashing it and made a mistake.
Same problem my younger brother ****ed up with his phone and I didn't got solution
Please
i have some problem sir (
tejeshjadhav.tj said:
My Moto E has been dead.......
It doesnt power up at all.....When i press POWER + VOLDOWN together nothing happens and When i do it while plugged in the notification led blinks once......and when plugged into pc it shows "RELINK HS-USB QDLoader 9008 (COM3)"....The pc plays the connected sound periodically every 1 or 2 mins with notification light blinking,.
It happened when i wanted to update from cm13 to cm14.1...i updated my TWRP to 3.0.2 Successfully. Then I Wiped to Factory and installed cm14.1 Successfully...eventually When i tried installing Open Gaaps it failed showing not sufficient storage space......
Then I tried formatting internal SD and also wanted to format external SD but was unable. It gave me error that "ext-sd is in unknown file system" inorder to format this I tried formatting using "fastboot format external_sd" in fastboot....It gave me error 'unable to format raw partition"....then after googling I got to know that I had used External SD as internal in cm13 and so twrp was unable to format ext-sd....
Then i created partition using twrp in external sd..and then using advance wipe wiped data , internal storage, cache , dalvik cache, ext3-sd(or whatever it is), external storage....and it was successful.........and so i rebooted to recovery and after it is just dead........
i tried blankflash.bat but its giving error "
.C:\Users\Admin\Desktop\blankflash\blankflash>.\qboot.exe blank-flash
opening device: \\.\COM3
OKAY [ -0.000s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x3964945
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.016s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.000s]
validating files
OKAY [ 0.000s]
switching to download mode
OKAY [ 0.016s]
greeting device for image downloading
OKAY [ 0.000s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\Users\Admin\Desktop\blankflash\blankflash>pause
Press any key to continue . . "
Then i read in one of the forum that blankflash is for moto G device..
I had a look at this but didnt got anything http://forum.xda-developers.com/moto-e/general/unbricking-hard-bricked-moto-e-t3306809
I aslo found this Guide : (Unbrick Qualcomm mobiles with Step-by-step guide)... but in this guide the phone is showing : "Qualcomm HS-USB QDLoader 9008" and my device is showing : "RELINK HS-USB QDLoader 9008" so what should i do???
Pls help me unbrick this device coz i dont have any money for service center (₹500 & ₹1000 denomination banned )
Hope this is correct section to post this thread
Click to expand...
Click to collapse
slayer_cyrus said:
Yeah pls help me I am stuck at same problem...
Click to expand...
Click to collapse
Tapriwalaraju said:
Pls give a solution
Click to expand...
Click to collapse
Dobbypoly said:
Devs pls give a legit solution
Click to expand...
Click to collapse
Danymanidy said:
This happened 1 month ago......still no solution
Click to expand...
Click to collapse
JosephBlessingh said:
my moto e is dead since the past 3 days. Was flashing it and made a mistake.
Click to expand...
Click to collapse
The invincibles said:
Please
Click to expand...
Click to collapse
mazoerkam said:
i have some problem sir (
Click to expand...
Click to collapse
@mazoerkam @The invincibles @JosephBlessingh @Danymanidy @Dobbypoly @Tapriwalaraju @slayer_cyrus @tejeshjadhav.tj Have a look at my DevDB project - Unbrick hard bricked Motorola Moto E - Aravind V. Nair
tejeshjadhav.tj said:
My Moto E has been dead.......
It doesnt power up at all.....When i press POWER + VOLDOWN together nothing happens and When i do it while plugged in the notification led blinks once......and when plugged into pc it shows "RELINK HS-USB QDLoader 9008 (COM3)"....The pc plays the connected sound periodically every 1 or 2 mins with notification light blinking,.
It happened when i wanted to update from cm13 to cm14.1...i updated my TWRP to 3.0.2 Successfully. Then I Wiped to Factory and installed cm14.1 Successfully...eventually When i tried installing Open Gaaps it failed showing not sufficient storage space......
Then I tried formatting internal SD and also wanted to format external SD but was unable. It gave me error that "ext-sd is in unknown file system" inorder to format this I tried formatting using "fastboot format external_sd" in fastboot....It gave me error 'unable to format raw partition"....then after googling I got to know that I had used External SD as internal in cm13 and so twrp was unable to format ext-sd....
Then i created partition using twrp in external sd..and then using advance wipe wiped data , internal storage, cache , dalvik cache, ext3-sd(or whatever it is), external storage....and it was successful.........and so i rebooted to recovery and after it is just dead........
i tried blankflash.bat but its giving error "
.C:\Users\Admin\Desktop\blankflash\blankflash>.\qboot.exe blank-flash
opening device: \\.\COM3
OKAY [ -0.000s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x3964945
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.016s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.000s]
validating files
OKAY [ 0.000s]
switching to download mode
OKAY [ 0.016s]
greeting device for image downloading
OKAY [ 0.000s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\Users\Admin\Desktop\blankflash\blankflash>pause
Press any key to continue . . "
Then i read in one of the forum that blankflash is for moto G device..
I had a look at this but didnt got anything http://forum.xda-developers.com/moto-e/general/unbricking-hard-bricked-moto-e-t3306809
I aslo found this Guide : (Unbrick Qualcomm mobiles with Step-by-step guide)... but in this guide the phone is showing : "Qualcomm HS-USB QDLoader 9008" and my device is showing : "RELINK HS-USB QDLoader 9008" so what should i do???
Pls help me unbrick this device coz i dont have any money for service center (₹500 & ₹1000 denomination banned )
Hope this is correct section to post this thread
Click to expand...
Click to collapse
Does it get fixed tejasjadhav.tj[/MENTION]
moto e xt1022 hardrick
My Moto E xt1022 has been dead
It doesnt power up at all.....When i press POWER + VOLDOWN together nothing happens and When i do it while plugged in the notification led blinks once......and when plugged into pc it shows "RELINK HS-USB QDLoader 9008 (COM3)
i tried blankflash.bat but its giving error "
.C:\Users\Admin\Desktop\blankflash\blankflash>.\qbo ot.exe blank-flash
opening device: \\.\COM3
OKAY [ -0.000s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x3964945
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.016s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.000s]
validating files
OKAY [ 0.000s]
switching to download mode
OKAY [ 0.016s]
greeting device for image downloading
OKAY [ 0.000s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
plz help me sir
sagary727 said:
My Moto E xt1022 has been dead
It doesnt power up at all.....When i press POWER + VOLDOWN together nothing happens and When i do it while plugged in the notification led blinks once......and when plugged into pc it shows "RELINK HS-USB QDLoader 9008 (COM3)
i tried blankflash.bat but its giving error "
.C:\Users\Admin\Desktop\blankflash\blankflash>.\qbo ot.exe blank-flash
opening device: \.\COM3
OKAY [ -0.000s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x3964945
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.016s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.000s]
validating files
OKAY [ 0.000s]
switching to download mode
OKAY [ 0.016s]
greeting device for image downloading
OKAY [ 0.000s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
plz help me sir
Click to expand...
Click to collapse
Follow this Tell me if this helps
https://forum.xda-developers.com/moto-e/general/unbrick-hard-bricked-moto-e-t2974093/amp/
mannu233 said:
Does it get fixed tejasjadhav.tj[/MENTION]
Click to expand...
Click to collapse
No It didnt got fixed by my efforts.
But got it repaired in Pune..
That guy Used JTAG to flash Firmware took like 5 mins n done... Costed Rs.500
still using that phone.
Related
Please help my Moto E XT1022 is hard bricked. I can't enter bootloader mode or even turn on. I need Moto E XT1022 qboot utility (flash blank) zip to enter bootloader mode
I downloaded from this thread but it seems the user has uploaded Moto G's qboot utility but I need Moto E XT1022 qboot utility
forum.xda-developers.com/moto-e/development/unbrick-hard-bricked-moto-e-t2974093
Sabarivelan said:
Please help my Moto E XT1022 is hard bricked. I can't enter bootloader mode or even turn on. I need Moto E XT1022 qboot utility (flash blank) zip to enter bootloader mode
I downloaded from this thread but it seems the user has uploaded Moto G's qboot utility but I need Moto E XT1022 qboot utility
forum.xda-developers.com/moto-e/development/unbrick-hard-bricked-moto-e-t2974093
Click to expand...
Click to collapse
do you solve your problem.cause i m having the same as yours
i have the same issue
myownway.1991 said:
do you solve your problem.cause i m having the same as yours
Click to expand...
Click to collapse
i tried to use motorola qboot utility but i get this:
C:\restore moto e\New folder\blankflash>.\qboot.exe blank-flash
opening device: \\.\COM11
OKAY [ 0.002s]
greeting device for command mode
OKAY [ 0.002s]
identifying device
...serial = 0x3BAEE53
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.005s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.003s]
validating files
OKAY [ 0.001s]
switching to download mode
OKAY [ 0.001s]
greeting device for image downloading
OKAY [ 0.002s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\restore moto e\New folder\blankflash>pause
Press any key to continue . . .
super1985 said:
i tried to use motorola qboot utility but i get this:
C:\restore moto e\New folder\blankflash>.\qboot.exe blank-flash
opening device: \\.\COM11
OKAY [ 0.002s]
greeting device for command mode
OKAY [ 0.002s]
identifying device
...serial = 0x3BAEE53
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.005s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.003s]
validating files
OKAY [ 0.001s]
switching to download mode
OKAY [ 0.001s]
greeting device for image downloading
OKAY [ 0.002s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\restore moto e\New folder\blankflash>pause
Press any key to continue . . .
Click to expand...
Click to collapse
did u get qboot utility of moto E?? i m having the same problem as yours. please help
i am also stuck at the qboot i need it for bootloader...so pls xda develpers must help because lot of them asking for it...if i go to the service center to fix it they ask for Rs.4000 to fix it..
I also has same issue, current qboot on the web is works with Moto G, If any has Qboot / Blankflash for MOTO E XT1022 please uplaod
Here it is..
PAHeartBeat said:
I also has same issue, current qboot on the web is works with Moto G, If any has Qboot / Blankflash for MOTO E XT1022 please uplaod
Click to expand...
Click to collapse
Not sure whether it will work or not but it is latest .
Previously i also had the same problem but fortunately my phone was in warranty and they replaced my motherboard for free. So i did not got any chance to test them. Try and report back. DO AT YOUR ON RISK, I WILL NOT BE RESPONSIBLE FOR ANYTHING. @PAHeartBeat
plz anyone upload blankflash for moto e......urgently needed guys !! my phone is dead and i dont have money to buy a new one
dude this is for moto g.....please uplload blankflash for moto e...it would be a great help
does any body got the solution to debrick the hard bricked moto e ?
Any updates on this issue? I too have a bricked moto e now. obviously out of warranty, Any idea how much mobo would cost////?
Looking for blank flash.
:crying::crying: same problem... plz help...
i too need blankflash for xt1022
i too need blank flash files for my hard bricked moto e.
here also same need blank flash.... as i searched there is no release moto e
Sabarivelan said:
Please help my Moto E XT1022 is hard bricked. I can't enter bootloader mode or even turn on. I need Moto E XT1022 qboot utility (flash blank) zip to enter bootloader mode
I downloaded from this thread but it seems the user has uploaded Moto G's qboot utility but I need Moto E XT1022 qboot utility
forum.xda-developers.com/moto-e/development/unbrick-hard-bricked-moto-e-t2974093
Click to expand...
Click to collapse
Same problem, did you solve?
same problem.. (
I Find a way!!!
BrandonCJesus said:
Same problem, did you solve?
Click to expand...
Click to collapse
Look for this in google "how to unbrick qualcomm devices"
http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
I have not tried it yet. Any volunteer?
Need Moto E XT1022 qboot utility (flash blank) zip
myownway.1991 said:
do you solve your problem.cause i m having the same as yours
Click to expand...
Click to collapse
Error...:crying::crying::crying: To run The Blank Flash file...
Plzz Hepl
opening device: \\.\COM3
OKAY [ 0.002s]
greeting device for command mode
OKAY [ 0.001s]
identifying device
...serial = 0x39B73FB
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.004s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.003s]
validating files
OKAY [ 0.001s]
switching to download mode
OKAY [ 0.001s]
greeting device for image downloading
OKAY [ 0.001s]
sending programmer
OKAY [ 0.012s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
Noo... the same unresolved problem
the same unresolved problem
Nothing_work_for_me_can_anybody_suggest_how_i_repair_this_kind_of_problem?
Hello everyone! I have the phone in hard bricked, I read on the forums that you can solve, not my model (xt1524) but other models. I tried some procedures but has not been able to solve anything. Can someone tell me how to call the files I have to try. I tried with Motoflasher but still not valid for my model. So I would try to look for files that I need but do not know their names. Thank you! I read somewhere that would serve certain files that are called programmer.mbm and singleimage.bin. Can someone tell me exactly what they're called to my phone.? Thank you!
Maybe is usefull :
- http://forum.xda-developers.com/moto-e-2015/general/stock-firmware-images-t3049047
- http://techtrickz.com/how-to/reinstall-stock-firmware-on-2nd-generation-moto-e-2015/
thanks, but the firmware is I, I can not install it because not light! I can only access it via the "Qualcomm HS-USB QDLoader 9008". Reading the various forums say that you need the program Motoflasher and certain files to switch it on and enter Fastboot. The problem is that I do not know which files I need.
anyone knows why I get this error?
**** QBOOT SELECTION STARTED: ****
**** BOOTLOADER FLASHING STARTED: ****
OUTPUT: opening device: \\.\COM9
OUTPUT: OKAY [ 0.001s]
OUTPUT: greeting device for command mode
OUTPUT: OKAY [ 0.001s]
OUTPUT: identifying device
OUTPUT: ...serial = 0x63000FE
OUTPUT: ...chip-id = 0x705
OUTPUT: ...chip-rev = 0x0
OUTPUT: ...sv-sbl = 0x0
OUTPUT: OKAY [ 0.002s]
OUTPUT: finding files
OUTPUT: ...programmer = programmer.mbn
OUTPUT: ...singleimage = singleimage.bin
OUTPUT: OKAY [ 0.001s]
OUTPUT: validating files
OUTPUT: OKAY [ 0.002s]
OUTPUT: switching to download mode
OUTPUT: OKAY [ -0.000s]
OUTPUT: greeting device for image downloading
OUTPUT:
OUTPUT: OKAY [ -0.000s]
OUTPUT: sending programmer
OUTPUT: Unexpected packet: 4. Was expecting: 3
OUTPUT: FAILED (blank-flash:sahara-transfer-image:send-image:unexpected packet)
OUTPUT:
hemikranion said:
anyone knows why I get this error?
**** QBOOT SELECTION STARTED: ****
**** BOOTLOADER FLASHING STARTED: ****
OUTPUT: opening device: \\.\COM9
OUTPUT: OKAY [ 0.001s]
OUTPUT: greeting device for command mode
OUTPUT: OKAY [ 0.001s]
OUTPUT: identifying device
OUTPUT: ...serial = 0x63000FE
OUTPUT: ...chip-id = 0x705
OUTPUT: ...chip-rev = 0x0
OUTPUT: ...sv-sbl = 0x0
OUTPUT: OKAY [ 0.002s]
OUTPUT: finding files
OUTPUT: ...programmer = programmer.mbn
OUTPUT: ...singleimage = singleimage.bin
OUTPUT: OKAY [ 0.001s]
OUTPUT: validating files
OUTPUT: OKAY [ 0.002s]
OUTPUT: switching to download mode
OUTPUT: OKAY [ -0.000s]
OUTPUT: greeting device for image downloading
OUTPUT:
OUTPUT: OKAY [ -0.000s]
OUTPUT: sending programmer
OUTPUT: Unexpected packet: 4. Was expecting: 3
OUTPUT: FAILED (blank-flash:sahara-transfer-image:send-image:unexpected packet)
OUTPUT:
Click to expand...
Click to collapse
Navigate in your bootloader to factory mode and then press the power button around 20-40 times before it boots up...Then unlock the bootloader and flash the Stock ROM for your model
the device does not start at all, there just led blinking on moto g4 plus
bsuthar said:
the device does not start at all, there just led blinking on moto g4 plus
Click to expand...
Click to collapse
Just flash your device with stock rom using sp flash tools .your device will start.
What he said ^^ Download the latest Stock ROM for your device, and issue the commands mentioned in @fratellos link one after another most likely you should get it back up.
skkethwas said:
Just flash your device with stock rom using sp flash tools .your device will start.
Click to expand...
Click to collapse
plss help me....
i have moto e4 and i don't know which file flashed first preloader.bin or pgpt.bin
first of all i flash preloader.bin and other factory images when i am going to flash pgpt.bin command ended up with error like this "PGPT: partition table not found" . after this wiped userdata and relock the bootloader. on fastboot reboot device cannot boot into system, no bootlogo, no fastboot, no recovery but recognized by PC and Miracle tool also charging led blink.
is this a softbrick or hardbrick.
Moto E4 won't power on. only white light led comes up when connecting with pc or charger. device recognized by pc.
kartik verma said:
plss help me....
i have moto e4 and i don't know which file flashed first preloader.bin or pgpt.bin
first of all i flash preloader.bin and other factory images when i am going to flash pgpt.bin command ended up with error like this "PGPT: partition table not found" . after this wiped userdata and relock the bootloader. on fastboot reboot device cannot boot into system, no bootlogo, no fastboot, no recovery but recognized by PC and Miracle tool also charging led blink.
is this a softbrick or hardbrick.
Moto E4 won't power on. only white light led comes up when connecting with pc or charger. device recognized by pc.
Click to expand...
Click to collapse
I think this can help you
https://forum.xda-developers.com/moto-e4/how-to/moto-e4-guide-stock-firmware-restore-t3661684
< waiting for device >
opening device: \\.\COM5
OKAY [ 0.004s]
greeting device for command mode
OKAY [ 0.003s]
identifying device
...serial = 0x42BC4F8
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.008s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.007s]
validating files
OKAY [ 0.001s]
switching to download mode
OKAY [ 0.001s]
greeting device for image downloading
OKAY [ 0.002s]
sending programmer
Unexpected packet: 4. Was expecting: 3
FAILED (blank-flash:sahara-transfer-image:send-image:unexpected packet)
there were something wrong in programmer.mbn file
is any one knows what programmer.mbn file contain .
i thought it contain qualcomm msm programmer code and some sdi.img file content.
before adding sdi file it cant start download but after adding some sdi content then phone goes to downloading image but has some packet problem .please help
Mine tooo.......
hiten7236 said:
< waiting for device >
opening device: \\.\COM5
OKAY [ 0.004s]
greeting device for command mode
OKAY [ 0.003s]
identifying device
...serial = 0x42BC4F8
...chip-id = 0x811
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.008s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.007s]
validating files
OKAY [ 0.001s]
switching to download mode
OKAY [ 0.001s]
greeting device for image downloading
OKAY [ 0.002s]
sending programmer
Unexpected packet: 4. Was expecting: 3
FAILED (blank-flash:sahara-transfer-image:send-image:unexpected packet)
there were something wrong in programmer.mbn file
is any one knows what programmer.mbn file contain .
i thought it contain qualcomm msm programmer code and some sdi.img file content.
before adding sdi file it cant start download but after adding some sdi content then phone goes to downloading image but has some packet problem .please help
Click to expand...
Click to collapse
Can u just upload the file in a zip which ur using...ill check that i may help u....
I have the same problem, I was constantly changing roms and never had this problem at most had a bootloop, but that was all. :crying:
I tried with Miflash, blankflash does not work, the only options that remain are to develop the missing files and / or find out who gave him solution for hardbrick moto X and moto G and ask him where he got those files or how made the files?
So, can you tell me... We need to find any solution, the problem is old, I realized when I read the forums and others.
My English is horrible, in fact I do not speak English, I speak Spanish, but I do understand some English
I'm new here
Harsh_1998 said:
Can u just upload the file in a zip which ur using...ill check that i may help u....
Click to expand...
Click to collapse
@Harsh_1998 I have a blankflash zip file but its a older version and I need a newer but Motorola isn't releasing blankflash zip file for Moto X Play and I found it myself and now my device got hard bricked can you see to it I need a blankflash for unbricking my device. Please help!!!!
Hi everyone,
I am having a problem to my moto G xt1032 which i recently updated through OTA. afetr I installed it dies. never turning on. but the led light will blink after i charge a few minutes. but never turn on.
Do anyone have an idea?
please help me.
I would really appreciate and commend.
thank you.
Firstly I flashed it with a xt1033 firmware 4.4.4 which has a dual sim flatform due to I cannot flash it with its own xt1032 firmware. maybe its a corrupt file.
After done flashing with xt1033, the phone work perfectly. it only happens after i recieved the system update from android system update
It is recognized by your PC ?
Sent from my SM-T116 using XDA Free mobile app
Soufiansky said:
It is recognized by your PC ?
Sent from my SM-T116 using XDA Free mobile app
Click to expand...
Click to collapse
Qualcomm HS-USB QDLoader 9008
on device manager
skripton78 said:
Qualcomm HS-USB QDLoader 9008
on device manager
Click to expand...
Click to collapse
Can you try to flash again the stock firmware ?
no display at all. i had try 2 and 15 minute method, even i tried removing and draining the electrons lift on the board no effects.
i cant put to recovery and fastboot mode. but the phone was detected as Qualcomm HS-USB QDLoader 9008. but commands is only waiting for device.
in short, dead.
skripton78 said:
Qualcomm HS-USB QDLoader 9008
on device manager
Click to expand...
Click to collapse
its bricked. you need blank flash files to flash the bootloader again, here try this http://forum.xda-developers.com/moto-g/help/how-to-revive-hard-bricked-moto-g-t2833798
blank-flash
nk-flash
opening device: \\.\COM11
OKAY [ -0.000s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x485D868
...chip-id = 0x800 (MSM8226)
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ -0.000s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ -0.000s]
validating files
OKAY [ 0.080s]
switching to download mode
OKAY [ 0.010s]
greeting device for image downloading
OKAY [ 0.000s]
sending programmer
OKAY [ 0.010s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error reading packet)
C:\Users\khyrt klyetz\Downloads\Compressed\blankflash\blankflash>pause
Press any key to continue . . .
skripton78 said:
nk-flash
opening device: \\.\COM11
OKAY [ -0.000s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x485D868
...chip-id = 0x800 (MSM8226)
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ -0.000s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ -0.000s]
validating files
OKAY [ 0.080s]
switching to download mode
OKAY [ 0.010s]
greeting device for image downloading
OKAY [ 0.000s]
sending programmer
OKAY [ 0.010s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error reading packet)
C:\Users\khyrt klyetz\Downloads\Compressed\blankflash\blankflash>pause
Press any key to continue . . .
Click to expand...
Click to collapse
FYI : this is already unlocked : status code 3 last time i'd flashed the firmware.
skripton78 said:
FYI : this is already unlocked : status code 3 last time i'd flashed the firmware.
Click to expand...
Click to collapse
do anyone have? here.
Hey all. Ran into a bit of an issue. My Motorola Edge Plus (XT2061-3) is stuck in EDL mode. I have managed to locate the blankflash file for this device. When trying to flash it, this is the errors I get. (Got this blankflash of Lolinet under Burton > Blankflash)
"Motorola qboot utility version 3.86
[ 0.000] Opening device: \\.\COM3
[ 0.008] Detecting device
[ 0.010] ...cpu.id = 195 (0xc3)
[ 0.010] ...cpu.sn = 621922316 (0x2511c80c)
[ 0.010] Opening singleimage
[ 0.020] Loading package
[ 0.022] ...filename = pkg.xml
[ 0.024] Loading programmer
[ 0.024] ...filename = programmer.elf
[ 0.024] Sending programmer
[ 0.089] ReadFile() failed, GetLastError()=0
[ 0.454] Unexpected command, expecting 3 or 18 or 4, got 1 instead.
[ 0.455] ERROR: sahara_download()->general error
[ 0.455] Check qboot_log.txt for more details
[ 0.455] Total time: 0.456s
FAILED: qb_flash_singleimage()->sahara_download()->general error
blankflash_from_QPBS30.188-48-3 (1)>pause
Press any key to continue . . ."
From the log file:
"
[ 0.000] Opening device: \\.\COM6
[ 0.001] Detecting device
[ 0.003] ...cpu.id = 195 (0xc3)
[ 0.003] ...cpu.sn = 621922316 (0x2511c80c)
[ 0.003] Opening singleimage
[ 0.013] Loading package
[ 0.016] ...filename = pkg.xml
[ 0.017] Loading programmer
[ 0.018] ...filename = programmer.elf
[ 0.018] Sending programmer
[ 0.088] ReadFile() failed, GetLastError()=0
[ 0.335] Unexpected command, expecting 3 or 18 or 4, got 1 instead.
[ 0.336] ERROR: sahara_download()->general error
[ 0.336] Check qboot_log.txt for more details
[ 0.336] Total time: 0.338s
[ 0.336]
[ 0.336] qboot version 3.86
[ 0.336]
[ 0.336] DEVICE {
[ 0.336] name = "\\.\COM6",
[ 0.336] flags = "0x64",
[ 0.336] addr = "0x62FD54",
[ 0.336] sahara.current_mode = "0",
[ 0.336] api.buffer = "0x2A5A020",
[ 0.336] cpu.serial = "621922316",
[ 0.336] cpu.id = "195",
[ 0.336] cpu.sv_sbl = "1",
[ 0.336] cpu.name = "SM8250",
[ 0.336] storage.type = "UFS",
[ 0.336] sahara.programmer = "programmer.elf",
[ 0.336] api.bnr = "0x2993FE0",
[ 0.336] }
[ 0.336]
[ 0.336]
[ 0.336] Backup & Restore {
[ 0.336] num_entries = 0,
[ 0.336] restoring = "false",
[ 0.336] backup_error = "not started",
[ 0.336] restore_error = "not started",
[ 0.336] }
[ 0.336]
"
It tries to send "programmer.elf" and "pkg.xml". The blankflash package does not contain those files. I have all the correct drivers. The phone shows up as "Qualcomm HS-USB QDLoader 9008" in Device Manager.
Any help is greatly appreciated. I've been stuck on this for quite a while.
latest blank flash for android 11
download here
I just brought my edge back to life. hope it helps. remember to update gpt.bin of ur own version
jackeylei said:
latest blank flash for android 11
download here
I just brought my edge back to life. hope it helps. remember to update gpt.bin of ur own version
Click to expand...
Click to collapse
It worked! Thank you so much for providing this.
I have the same problem on moto edge 20 pro any suggestions thank you very much
I have the same problem on moto edge foto here https://ibb.co/7Vz3vBg help me plss
jackeylei said:
último flash en blanco para android 11
descarga aquí
Acabo de traer mi borde de vuelta a la vida. Espero eso ayude. recuerda actualizar gpt.bin de tu propia versión
Click to expand...
Click to collapse
¿Puede indicar los pasos para actualizar gpt.bin?
marcoryu said:
¿Puede indicar los pasos para actualizar
Click to expand...
Click to collapse
There are some tutorial posts in this forum, just search for posts related to blank flash and understand how to use.
My general suggestion is to "extract some files from the firmware and put them into the singleimage file in the blank flash folder".
jackeylei said:
There are some tutorial posts in this forum, just search for posts related to blank flash and understand how to use.
My general suggestion is to "extract some files from the firmware and put them into the singleimage file in the blank flash folder".
Click to expand...
Click to collapse
exactly which firmware files should i move to the blankflash folder
AREALE said:
I have the same problem on moto edge foto here https://ibb.co/7Vz3vBg help me plss
Click to expand...
Click to collapse
Just keep trying
marcoryu said:
exactly which firmware files should i move to the blankflash folder
Click to expand...
Click to collapse
1. You have to determine which firmware ur phone is on when bricked then download the firmware from here and the right blankflash file here
2. Get gpt.bin from the firmware, and put it into singleimage file.
3. Flash
Refer to this post:
[BLANKFLASH] Moto G7 XT1962-5 RIVER RETEU 9.0 PPO29.80-66
I have built a blankflash that revived my XT1962-5, which had firmware PPO29.80-66 before hardbricking it. Maybe it is useful to others: https://www27.zippyshare.com/v/lL4eo830/file.html The blankflash is based on this firmware...
forum.xda-developers.com
good morning friend, could you help me create the blank flash to be able to recover my device, thank you very much for answering and for your help
jackeylei said:
1. You have to determine which firmware ur phone is on when bricked then download the firmware from here and the right blankflash file here
2. Get gpt.bin from the firmware, and put it into singleimage file.
3. Flash
Refer to this post:
[BLANKFLASH] Moto G7 XT1962-5 RIVER RETEU 9.0 PPO29.80-66
I have built a blankflash that revived my XT1962-5, which had firmware PPO29.80-66 before hardbricking it. Maybe it is useful to others: https://www27.zippyshare.com/v/lL4eo830/file.html The blankflash is based on this firmware...
forum.xda-developers.com
Click to expand...
Click to collapse
good morning friend, could you help me create the blank flash to be able to recover my device, thank you very much for answering and for your help
marcoryu said:
good morning friend, could you help me create the blank flash to be able to recover my device, thank you very much for answering and for your it
Click to expand...
Click to collapse
When the phone bricked, is it on Android 11 or 10? When it happened?
jackeylei said:
When the phone bricked, is it on Android 11 or 10? When it happened?
Click to expand...
Click to collapse
Android 11 https://mirrors.lolinet.com/firmwar...ubsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip in this version it was when it was blocked
marcoryu said:
Android 11 https://mirrors.lolinet.com/firmwar...ubsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip in this version it was when it was blocke
Click to expand...
Click to collapse
windows recognizes it as Qulcomm hs-usb Dloader 9008
Have u tried this blankflash? if yes, what's the error msg?
I assume that you already know how to use blankflash. otherwise, it is difficult for me to explain.
jackeylei said:
Have u tried this blankflash? if yes, what's the error msg?
I assume that you already know how to use blankflash. otherwise, it is difficult for me to explain.
Click to expand...
Click to collapse
Here I attach the blankflash file which I update the gpt.bin provided in your firmware. Try the original blankflash first, if failed, try this one.
jackeylei said:
Here I attach the blankflash file which I update the gpt.bin provided in your firmware. Try the original blankflash first, if failed, try this one.
Click to expand...
Click to collapse
hello mate and tried the blank flash file of version 19.50 and the one you sent me and both give me this error
marcoryu said:
hello mate and tried the blank flash file of version 19.50 and the one you sent me and both give me this error
Click to expand...
Click to collapse
Try , keep trying.
Based on my personal understanding, u have only one chance to blank flash ur phone during the connection with pc.
Therefore after u plug in the USB, u should keep running blank-flash command until the real results display.
Try.
Check others posts about blank flash.