Related
My Lenovo P780 does not boot any more. Push power button, nothing happened. Connect by usb cable, only red led works. What can I do?
Bought from china, chinaunicomm customed phone. I tried flash, but can not connect it to computer.
bonbonbillo said:
My Lenovo P780 does not boot any more. Push power button, nothing happened. Connect by usb cable, only red led works. What can I do?
Bought from china, chinaunicomm customed phone. I tried flash, but can not connect it to computer.
Click to expand...
Click to collapse
Did u installed p780 drivers into your Pc ?
u must if u want to flash it .
bonbonbillo said:
My Lenovo P780 does not boot any more. Push power button, nothing happened. Connect by usb cable, only red led works. What can I do?
Bought from china, chinaunicomm customed phone. I tried flash, but can not connect it to computer.
Click to expand...
Click to collapse
It's easy to fix Just follow my steps. :fingers-crossed:
1.Prepare the rom which was running ok before,for example, for me it was @satanduck 's prerooted TWRP S124 rom.
2.Open the SP flash tool.
3.Load the scatter file from the rom which worked ok for you.
4.Tick the box that says 'DA DL All With Check Sum'
5.Hit Firmware Upgrade
Now is the hardest step
1.Open the cover of your phone.
2.Look for the red reset button which was close to SD card and press it a few times.
3.Connect USB cable to your phone and firmware upgrade should start and wait for the green circle! :good::laugh:
Best luck :good:
bonbonbillo said:
My Lenovo P780 does not boot any more. Push power button, nothing happened. Connect by usb cable, only red led works. What can I do?
Bought from china, chinaunicomm customed phone. I tried flash, but can not connect it to computer.
Click to expand...
Click to collapse
What have you done to your phone? Did you install or flash something? Did you change something in system ?
Sent from my Lenovo P780 with TWRP 2.7.1.1
glixbourkt said:
Did u installed p780 drivers into your Pc ?
u must if u want to flash it .
Click to expand...
Click to collapse
Yes, I installed mtk usb drivers. but I´m not sure if it´s ok o no. Because I have to connect the battery and push volume+up button to make it connected. and it´ll disappear immediately in device management window.
stympy said:
What have you done to your phone? Did you install or flash something? Did you change something in system ?
Sent from my Lenovo P780 with TWRP 2.7.1.1
Click to expand...
Click to collapse
Just tried to root, but not completed. and then tried flash to rescue, but not yet get it connected to computer.
tngultimate said:
It's easy to fix Just follow my steps. :fingers-crossed:
1.Prepare the rom which was running ok before,for example, for me it was @satanduck 's prerooted TWRP S124 rom.
2.Open the SP flash tool.
3.Load the scatter file from the rom which worked ok for you.
4.Tick the box that says 'DA DL All With Check Sum'
5.Hit Firmware Upgrade
Now is the hardest step
1.Open the cover of your phone.
2.Look for the red reset button which was close to SD card and press it a few times.
3.Connect USB cable to your phone and firmware upgrade should start and wait for the green circle! :good::laugh:
Best luck :good:
Click to expand...
Click to collapse
I can not get it connected to computer. Only when I push volume+up button,and connect the usb cable, it can be found. But then it disappears immediately in device management window. can not continue to flash.
Hi,
Please verify that you have a correct production date. I got a P780 after 0314. please try the solution on this post
http://forum.xda-developers.com/showpost.php?p=52665841&postcount=16
If this resolves your problem, that keep that preloader. With that you can almost flash every rom that there is with the flashtool.
(i'm very satisfied with the latest rom on needrom Vibeui2.0 (the rom page also offers the new preloader )
Greetz,
btw to try to flash with the new preloader set up the flashtool, push the red button on the back of your phone, connect the phone an release the button. If all the drivers are correct your phone will be flashed. ( this new batch phones gave me a heart attack also , mine wasn't even 12 hours active before i softbricked it )
Re-Mi said:
Hi,
Please verify that you have a correct production date. I got a P780 after 0314. please try the solution on this post
http://forum.xda-developers.com/showpost.php?p=52665841&postcount=16
If this resolves your problem, that keep that preloader. With that you can almost flash every rom that there is with the flashtool.
(i'm very satisfied with the latest rom on needrom Vibeui2.0 (the rom page also offers the new preloader )
Greetz,
btw to try to flash with the new preloader set up the flashtool, push the red button on the back of your phone, connect the phone an release the button. If all the drivers are correct your phone will be flashed. ( this new batch phones gave me a heart attack also , mine wasn't even 12 hours active before i softbricked it )
Click to expand...
Click to collapse
When I push the red button, phone can not be recognized by computer. Only I press the volume-up button, it can be recognized by computer.
I start the flash, then push volume-up button to make it connected, but then got BROM error. I attach the screen picture.
bonbonbillo said:
When I push the red button, phone can not be recognized by computer. Only I press the volume-up button, it can be recognized by computer.
I start the flash, then push volume-up button to make it connected, but then got BROM error. I attach the screen picture.
Click to expand...
Click to collapse
You must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
Check if your phone is produced in 2014. If it is you must use another preloader.
stympy said:
You must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
Check if your phone is produced in 2014. If it is you must use another preloader.
Click to expand...
Click to collapse
Yes, I have the FlashTool v3.1304.0.119. (picture attached)
My phone is produced before 2014.
bonbonbillo said:
Yes, I have the FlashToll v3.1304.0.119. (picture attached)
My phone is produced before 2014.
Click to expand...
Click to collapse
Try to flash with this Flah Tool, and tell me if gives you new errors.
stympy said:
Try to flash with this Flah Tool, and tell me if gives you new errors.
Click to expand...
Click to collapse
Which one? Have you attached any file? I don't see it. Tks.
bonbonbillo said:
Which one? Have you attached any file? I don't see it. Tks.
Click to expand...
Click to collapse
I have attached now.
Sent from my Lenovo P780 with TWRP 2.7.1.1
stympy said:
I have attached now.
Sent from my Lenovo P780 with TWRP 2.7.1.1
Click to expand...
Click to collapse
Same error, when the red color goes to the end, after around 3 minutes, says brom error....4001
bonbonbillo said:
Same error, when the red color goes to the end, after around 3 minutes, says brom error....4001
Click to expand...
Click to collapse
I think you should go to a service store. Thats my opinion.
stympy said:
I think you should go to a service store. Thats my opinion.
Click to expand...
Click to collapse
Trying to find solution here, not to solve only with money in mobile store. Anybody else help?
bonbonbillo said:
Trying to find solution here, not to solve only with money in mobile store. Anybody else help?
Click to expand...
Click to collapse
I thought you have warranty on your phone !
So... this error appear when you try to flash wrong ROM or you have wrong drivers installed. Try to remove drivers you have installed and try to reinstall another driver.
Orrrr.. your phone could be a clone. Just an ideea ...
Could you tell us more about your phone... maybe pictures taken from battery or box who came with ?
Hi,
I installed Lenovo P780 VibeUI 2.0 version: VIBEUI_V2.0_1512_DEV_P780 and gapps-kk-20150404-minimal-edition-signed.zip.
Then I installed Google Calendar from Play Store. Unfortunately it doesn't sync. If I go to settings/accounts/google there is no "google calendar data" option to choose.
marekjarosz said:
Hi,
I installed Lenovo P780 VibeUI 2.0 version: VIBEUI_V2.0_1512_DEV_P780 and gapps-kk-20150404-minimal-edition-signed.zip.
Then I installed Google Calendar from Play Store. Unfortunately it doesn't sync. If I go to settings/accounts/google there is no "google calendar data" option to choose.
Click to expand...
Click to collapse
Try to install full gapps pack.
Sent from my Lenovo P780
stympy said:
Try to install full gapps pack.
Click to expand...
Click to collapse
Any recommended source?
marekjarosz said:
Any recommended source?
Click to expand...
Click to collapse
Try the pack from cyanogen.
Sent from my SMT TAB 704DC
stympy said:
Try the pack from cyanogen.
Click to expand...
Click to collapse
Unfortunately I used [GApps][4.4.2][AROMA]_Aroma_Installer_GApps-v1.5.2 and didn't wipe data before/after. After rebooting the phone got "Lenovo launcher stopped, must be closed". After swithching the phone off and on end up with an infinite bootloop.
I rebooted the phone into recovery mode and wiped data, cache and dalvik and tried to reinstall VIBEUI_V2.0_1512_DEV_P780. After the first launch there is only a chinese text (I guess it might be some error, after clicking the button the same error apears again and again).
I tried to flash a custom revovery (as I end up with a Lenovo-Recovery with nothing to do) with a Flash Tool V5.13.52.200 as described in other thread but after clicking "download" and connecting the phone nothing happens (phone shows red light and a battery charge screen). The phone is recognized by the PC (Win 7) as even after turning the phone on again it is possible to upload files to the SD card using windows explorer.
marekjarosz said:
Unfortunately I used [GApps][4.4.2][AROMA]_Aroma_Installer_GApps-v1.5.2 and didn't wipe data before/after. After rebooting the phone got "Lenovo launcher stopped, must be closed". After swithching the phone off and on end up with an infinite bootloop.
I rebooted the phone into recovery mode and wiped data, cache and dalvik and tried to reinstall VIBEUI_V2.0_1512_DEV_P780. After the first launch there is only a chinese text (I guess it might be some error, after clicking the button the same error apears again and again).
I tried to flash a custom revovery (as I end up with a Lenovo-Recovery with nothing to do) with a Flash Tool V5.13.52.200 as described in other thread but after clicking "download" and connecting the phone nothing happens (phone shows red light and a battery charge screen). The phone is recognized by the PC (Win 7) as even after turning the phone on again it is possible to upload files to the SD card using windows explorer.
Click to expand...
Click to collapse
Hi. Try to reflash using SP Flash Tool v5 from my post Rooting Tutorial for KK.
I use ONLY those tools. Tested and modified for P780.
Sent from my Lenovo P780
stympy said:
Hi. Try to reflash using SP Flash Tool v5 from my post Rooting Tutorial for KK.
I use ONLY those tools. Tested and modified for P780.
Click to expand...
Click to collapse
I used exactly those tools, but with a results described below:
I tried to flash a custom revovery (as I end up with a Lenovo-Recovery with nothing to do) with a Flash Tool V5.13.52.200 as described in other thread but after clicking "download" and connecting the phone nothing happens (phone shows red light and a battery charge screen).
Click to expand...
Click to collapse
marekjarosz said:
I used exactly those tools, but with a results described below:
Click to expand...
Click to collapse
seems to me that your phone is no longer detected by your computer !
se this:
1. go to device manager
2. with device manager window open plug your phone
3. in device manager in Ports tab something like MTK 65XX... will appear for 1 or 2 secconds
Tell me if this is going on !
stympy said:
seems to me that your phone is no longer detected by your computer !
se this:
1. go to device manager
2. with device manager window open plug your phone
3. in device manager in Ports tab something like MTK 65XX... will appear for 1 or 2 secconds
Tell me if this is going on !
Click to expand...
Click to collapse
My device is detected by my computer as I am able to copy files to SD card using windows explorer. I plug the phone and I see "Lenovo P780" in My Computer, then I open it and get access to internal memory and SD card.
BUT - I do not see it in the Device Manager at all... Maybe I will try to do it on the other Windows computer?
marekjarosz said:
My device is detected by my computer as I am able to copy files to SD card using windows explorer. I plug the phone and I see "Lenovo P780" in My Computer, then I open it and get access to internal memory and SD card.
BUT - I do not see it in the Device Manager at all... Maybe I will try to do it on the other Windows computer?
Click to expand...
Click to collapse
Try what i told you with the phone powered off!
The computer must have windows XP or windows 7!
Good Luck.
stympy said:
seems to me that your phone is no longer detected by your computer !
se this:
1. go to device manager
2. with device manager window open plug your phone
3. in device manager in Ports tab something like MTK 65XX... will appear for 1 or 2 secconds
Tell me if this is going on !
Click to expand...
Click to collapse
After connecting switched-off phone to the USB port MT65xx Preloader appears in the Device Manger for 1-2 seconds.
marekjarosz said:
After connecting switched-off phone to the USB port MT65xx Preloader appears in the Device Manger for 1-2 seconds.
Click to expand...
Click to collapse
Hi. You are lucky. Your phone is detected by your computer !
All you have to do is to flash a custom recovery TWRP CN Version.
After this you could download your firmware again and put it on sd card ! reboot to recovery wipe and reflash your firmware !
stympy said:
Hi. You are lucky. Your phone is detected by your computer !
All you have to do is to flash a custom recovery TWRP CN Version.
After this you could download your firmware again and put it on sd card ! reboot to recovery wipe and reflash your firmware !
Click to expand...
Click to collapse
Thanks for your reply, but as I wrote before I don't really know how to achieve it as it is not possible to do it using Flash Tool
marekjarosz said:
Thanks for your reply, but as I wrote before I don't really know how to achieve it as it is not possible to do it using Flash Tool
Click to expand...
Click to collapse
If you want i can help you. All you need is a connection by team viewer.
Sent from my Lenovo P780
I used [TUT] Instructions MTK6577 USB VCOM Driver Installation to install a proper driver and was able to flash a custom ROM to make it work as suppose to and was able to do the rest without any problems.
Thank you
Hey guys, so I have LG G2 Mini D620R rooted Android 5.0.2 (I think). So here is the problem: whenever I try to access settings it says: ''Unfortunatelly, Settings has stopped.'' This problem happened to me few times and I solved it with LG Mobile Support Tool, it just downloads full software from internet and install it to my phone. But now I can not do that. I try to do that when my phone is on but my computer don't recognize my device and I can not select connectivity on my phone because I can not get into settings. Last time I solved this problem going to download mode an that worked. Now when I go to download mode my computer does not recognize my phone. My phone is fully functionally and I can play games, use apps, I can do anything, just I can't go in Settings and thats just annoying. Even Bluetooth is crashing and calendar. I thing this problem came because I removed some apps that came pre installed like bloatware. I think it's because of Easy Home app which is some sort of launcher. Thanks for you reply.
Download the appropriate kdz file for your device(http://lg-phone-firmware.com/index.php?id_mod=57) and flash it using lg flash tool 2014(http://forum.xda-developers.com/showthread.php?t=2797190). After that be carefull of which stock apps you will delete so that the problem does not appear again!
Yes I found tutorial to do that and there is problem. I downloaded kdz and LG Flash Tool and done all needed but whe process goes then LG Mobile Support Tool runs for 15% and message pops out ant it says that it can not find phone. I spam reply but nothing. Just my computer does not recognize my mobile phone and thats it.
G1ML1 said:
Yes I found tutorial to do that and there is problem. I downloaded kdz and LG Flash Tool and done all needed but whe process goes then LG Mobile Support Tool runs for 15% and message pops out ant it says that it can not find phone. I spam reply but nothing. Just my computer does not recognize my mobile phone and thats it.
Click to expand...
Click to collapse
Do you flash the kdz while the phone is in download mode?
gismoO said:
Do you flash the kdz while the phone is in download mode?
Click to expand...
Click to collapse
This is what I have done: I turned off phone then I have connected USB to my PC and then went in download mode. Then I have downloaded kdz file and LG Flash Tool. Then I put kdz file into LGFT and I have started process. LG Mobile Support Tool pops out. Everything went OK until message pops out saying there's no connected phone.
G1ML1 said:
This is what I have done: I turned off phone then I have connected USB to my PC and then went in download mode. Then I have downloaded kdz file and LG Flash Tool. Then I put kdz file into LGFT and I have started process. LG Mobile Support Tool pops out. Everything went OK until message pops out saying there's no connected phone.
Click to expand...
Click to collapse
1. Check that your device appears in windows device manager.
2. Run Lg flash tool as administrator.
3. Check that you have the appropriate lg driver.
4. Try another micro-usb cable.
5. Try flashing it through another pc/ different windows version.
6. Do a cse and not a normal flash.
7. Try using emergency mode instead of DIAG (in cse mode).
8. If the above do not work, consider unlocking the bootloader, install TWRP custom recovery, install CM13 and feel the difference..
Hey I installed CWM 13 and Android 6 but I forgot to put GApps in it. How can I install GApps?
Hey again, so I installed GApps but I get crashes and I can not use phone. When phone boots I get to lock screen then I draw pattern and I got several crashes. I rebooted it few times but its same.
G1ML1 said:
Hey again, so I installed GApps but I get crashes and I can not use phone. When phone boots I get to lock screen then I draw pattern and I got several crashes. I rebooted it few times but its same.
Click to expand...
Click to collapse
Use Pico version.
Sent from my LG G2 Mini using XDA Labs
Vagelis1608 said:
Use Pico version.
Sent from my LG G2 Mini using XDA Labs
Click to expand...
Click to collapse
Hey, can you tell me what should I do now? I can't go into recovery mode because I can't run anything on phone. What should I do?
G1ML1 said:
Hey, can you tell me what should I do now? I can't go into recovery mode because I can't run anything on phone. What should I do?
Click to expand...
Click to collapse
Download Pico version of GAPPS on your PC and put it on an SD.
Use the hardware key combination to enter recovery mode.
Sent from my LG G2 Mini using XDA Labs
Vagelis1608 said:
Download Pico version of GAPPS on your PC and put it on an SD.
Use the hardware key combination to enter recovery mode.
Sent from my LG G2 Mini using XDA Labs
Click to expand...
Click to collapse
THANKS MAN, thanks to all who responded, thanks xda community, thanks to all who looked at this thread.
My device is working now and I have GApps. Cheers!
Hi all,
by cons for several weeks I've a concern with my redmi Note 2 and I can't find the answer to my problem on the forum or even the Internet.
Since the last update 7.2.2 (global) I have the Recovery MIUI who crushed the TWRP. I changed to test 6.3.17. The update to the .24 went wrong and I don't know why. Since the phone is bootloop. But the problem is that my phone is not recognized by any PC. I tried several PCs, several cables, several drivers, with or without the Fastboot, unable to connect. Therefore impossible to load a new version. I don't think it's material problem because the phone recharge well with a cable to the socket.
Is there another handling or debug decision to restart the phone? I'm in France for information.
thank you in advance if you can point me to a solution !
Hope someone can help me.
Manu
Can the phone boot to miui recovery? If so, you should be able to use miui recovery to flash TWRP (I think you will need one with a signed install zip). You only need to take out the external SD, put it in one of those cheap USB card readers, copy your recovery and ROM to the SD, put it back in the phone, flash TWRP with miui recovery, and then flash the ROM with TWRP (I am assuming that miui recovery can install things from the external SD - if not, then none of this will work).
Hi Bro,
Yes it boot in MIUI recovery but impossible to get access to the SD Card...
I tried to put the file on the SD card but you can't choose the path, I think the recovery will look only in the internal memory ... And as I can't access the internal memory..
I despair !!
Thanks o lot for your help
DarthJabba9 said:
Can the phone boot to miui recovery? If so, you should be able to use miui recovery to flash TWRP (I think you will need one with a signed install zip). You only need to take out the external SD, put it in one of those cheap USB card readers, copy your recovery and ROM to the SD, put it back in the phone, flash TWRP with miui recovery, and then flash the ROM with TWRP (I am assuming that miui recovery can install things from the external SD - if not, then none of this will work).
Click to expand...
Click to collapse
manu33xtro said:
Hi Bro,
Yes it boot in MIUI recovery but impossible to get access to the SD Card...
I tried to put the file on the SD card but you can't choose the path, I think the recovery will look only in the internal memory ... And as I can't access the internal memory..
I despair !!
Thanks o lot for your help
Click to expand...
Click to collapse
Ok - but have you tried the Mediatek SP Flash Tool?
Of course yes but the real problem is that the phone is not recognized by the PC and therefore can't load anything ...
Even changing drivers or cables or PC, nothing to do.
DarthJabba9 said:
Ok - but have you tried the Mediatek SP Flash Tool?
Click to expand...
Click to collapse
manu33xtro said:
Of course yes but the real problem is that the phone is not recognized by the PC and therefore can't load anything ...
Even changing drivers or cables or PC, nothing to do.
Click to expand...
Click to collapse
So, when the battery is removed, and you connect the USB cable, the phone is not even vibrating (and making that weird sound) every couple of seconds or so?
Yes you're right : every 10s the phone vibrate...
DarthJabba9 said:
So, when the battery is removed, and you connect the USB cable, the phone is not even vibrating (and making that weird sound) every couple of seconds or so?
Click to expand...
Click to collapse
manu33xtro said:
Yes you're right : every 10s the phone vibrate...
Click to expand...
Click to collapse
Well, then it is very strange that you can't use the SP Flash Tool. If the phone vibrates, then the device is recognised, and you should be able to flash anything you want with the SP Flash Tool! How exactly were you trying to use the Flash Tool?
I tried so many solutions I really don't know exactly how I used the software.
I will again try everything.
But against any changes when I look in the USB settings of the PC, the phone doesn't appear.
I try again just now, thank you for your help.
DarthJabba9 said:
Well, then it is very strange that you can't use the SP Flash Tool. If the phone vibrates, then the device is recognised, and you should be able to flash anything you want with the SP Flash Tool! How exactly were you trying to use the Flash Tool?
Click to expand...
Click to collapse
manu33xtro said:
I tried so many solutions I really don't know exactly how I used the software.
I will again try everything.
But against any changes when I look in the USB settings of the PC, the phone doesn't appear.
I try again just now, thank you for your help.
Click to expand...
Click to collapse
With the SP Flash Tool, all you need is the correct "scatter" file (MT6795_Android_scatter.txt), and the image(s) that you want to flash. If the phone is vibrating, then the SP Flash Tool should be able to connect to it when you click "Download". Just make sure that you first untick everything that you do NOT want to flash. I would try flashing the boot image (boot.img) first. If that succeeds, then try the TWRP recovery image.
Ok. I'm going to try again with "http://en.miui.com/forum.php?mod=viewthread&tid=196175&highlight=sp%2Btool%2Bflash%2Bredmi%2Bnote%2B2"
DarthJabba9 said:
With the SP Flash Tool, all you need is the correct "scatter" file (MT6795_Android_scatter.txt), and the image(s) that you want to flash. If the phone is vibrating, then the SP Flash Tool should be able to connect to it when you click "Download". Just make sure that you first untick everything that you do NOT want to flash. I would try flashing the boot image (boot.img) first. If that succeeds, then try the TWRP recovery image.
Click to expand...
Click to collapse
Well... Install again drivers MTK but nothing... The phone vibrates well but the PC still doesn't see ... It's late now, I look again tomorrow night.
Thanks again.
manu33xtro said:
Ok. I'm going to try again with "http://en.miui.com/forum.php?mod=viewthread&tid=196175&highlight=sp%2Btool%2Bflash%2Bredmi%2Bnote%2B2"
Click to expand...
Click to collapse
manu33xtro said:
Well... Install again drivers MTK but nothing... The phone vibrates well but the PC still doesn't see ... It's late now, I look again tomorrow night.
Thanks again.
Click to expand...
Click to collapse
Perhaps you might want to describe what exactly happens when do you what exactly?
Hi,
Ok that's what I do with an old PC with Win XP.
- install media Tek USB VCOM drivers for Win XP -> installation complete
- launch SP Flash Tool with administrator rights)
- use scatter file from Redmi Note 2 rom
- use download agent "MTK_AllInOne_DA.bin"
- press download button
- connect phone with UCB cable and waiting... and waiting...
- and I can't see it in device manager !
No way again !
I will try again...
DarthJabba9 said:
Perhaps you might want to describe what exactly happens when do you what exactly?
Click to expand...
Click to collapse
manu33xtro said:
Hi,
Ok that's what I do with an old PC with Win XP.
- install media Tek USB VCOM drivers for Win XP -> installation complete
- launch SP Flash Tool with administrator rights)
- use scatter file from Redmi Note 2 rom
- use download agent "MTK_AllInOne_DA.bin"
- press download button
- connect phone with UCB cable and waiting... and waiting...
- and I can't see it in device manager !
No way again !
I will try again...
Click to expand...
Click to collapse
Strange! I am assuming that when you connect the phone with the USB cable, the battery has been removed from the phone? If so, then it should work.
Perhaps you should try first connecting the phone, and then waiting until it has vibrated once or twice, before clicking the "Download" button?
Yes I removed battery before connect the phone to PC. I tried also with battery and nothing changed.
I even changed the cable to be sure.
Which seems to me most strange is that I see nothing in the device manager, as if the phone wasn't connected. Whatever the installed driver is the same result. I think it should at least have the phone on the COM or USB port ...
I will try again this night to be sure with all steps one by one. And I will also try with ACER tablet I and runs Android 5.1. Maybe it will be recognized.
Otherwise I also tried to pass a Linux PC as a last resort.
Thanks again for your help.
DarthJabba9 said:
Strange! I am assuming that when you connect the phone with the USB cable, the battery has been removed from the phone? If so, then it should work.
Perhaps you should try first connecting the phone, and then waiting until it has vibrated once or twice, before clicking the "Download" button?
Click to expand...
Click to collapse
manu33xtro said:
Yes I removed battery before connect the phone to PC. I tried also with battery and nothing changed.
I even changed the cable to be sure.
Which seems to me most strange is that I see nothing in the device manager, as if the phone wasn't connected. Whatever the installed driver is the same result. I think it should at least have the phone on the COM or USB port ...
Click to expand...
Click to collapse
Yes, it should. The fact that the phone vibrates when connected indicates that the PC and phone are communicating - but it may well be that a low-level driver in the phone has been overwritten (which may mean that this is a lost cause). A final idea - can miui recovery access usbotg?
Hum good question. In fact I don't know. I'll ask the MIUI forum.
I got home late from work so I don't do tests tonight, I'd see it all tomorrow including the connection with my tablet ...
Thanks
DarthJabba9 said:
Yes, it should. The fact that the phone vibrates when connected indicates that the PC and phone are communicating - but it may well be that a low-level driver in the phone has been overwritten (which may mean that this is a lost cause). A final idea - can miui recovery access usbotg?
Click to expand...
Click to collapse
Hi,
I tried to connect with an Acer Tablet with Android 5.1.1 but nothing appends...
I tried also with a Linux PC (Debian) and if I can see a Samsung A3 phone dirrectly, no way for my Redmi Note 2...
There really I despair : I think I can't access any of the phone. Can't do anything !
If you have any other solution but you help me a lot already, and thanks for that.
Can be a micro crack on the USB plug into the phone if it's not a software problem ... Let's go for it apart and look at this ...
Thanks again bro.
Manu
DarthJabba9 said:
Yes, it should. The fact that the phone vibrates when connected indicates that the PC and phone are communicating - but it may well be that a low-level driver in the phone has been overwritten (which may mean that this is a lost cause). A final idea - can miui recovery access usbotg?
Click to expand...
Click to collapse
manu33xtro said:
Hi,
I tried to connect with an Acer Tablet with Android 5.1.1 but nothing appends...
I tried also with a Linux PC (Debian) and if I can see a Samsung A3 phone dirrectly, no way for my Redmi Note 2...
There really I despair : I think I can't access any of the phone. Can't do anything !
If you have any other solution but you help me a lot already, and thanks for that.
Can be a micro crack on the USB plug into the phone if it's not a software problem ... Let's go for it apart and look at this ...
Thanks again bro.
Manu
Click to expand...
Click to collapse
I don't think it is a crack on the USB plug. It seems to me to be a low-level driver problem - ie, the drivers on the phone that are active when the phone is not (fully) booted up. I don't have the right terminology for these drivers, but they are possibly part of the bootloader. If that is the problem, then I don't know how you would solve this problem.
Hi,
i have Lg G2 D802 European (UK purchase) model phone of which is password locked, it was used by one of my family member and they have forgotten the Password. its in stock firmware.
here are the bellow issue i am facing;
1. USB Debugging mode is not activated
2. phone doesn't boot up to Recovery (for some reason its not going to recovery- key combination doesn't work)
3. wifi and Data was not active before its getting locked.
all i have is download mode. which is not been quite help. i have also user's Google account details which is also not been a help as WIFI/DATA is not being connecting.
I tried with LG suite, phone is getting recognized
i tried ADB, but phone doest get recognized to execute the command .
i tried almost all method which was provided in the XDA and couldn't get to their.
Please advice.
in this case you have only one option left and that is make reflash stock rom using download mode.
as you described debugging is off, No Data Connection, Recovery isn't accessible. you are simply locked away from any way to unlock your device
Download the stock Rom and flash it using Odin.
And remember one thing, always make sure USB Debugging is enabled, it really helps in such cases.
all the best
Hit Thanks if helped.
abhinavp649 said:
in this case you have only one option left and that is make reflash stock rom using download mode.
as you described debugging is off, No Data Connection, Recovery isn't accessible. you are simply locked away from any way to unlock your device
Download the stock Rom and flash it using Odin.
And remember one thing, always make sure USB Debugging is enabled, it really helps in such cases.
all the best
Hit Thanks if helped.
Click to expand...
Click to collapse
Odin Dint detect my phone in download mode.
akshayhgd said:
Odin Dint detect my phone in download mode.
Click to expand...
Click to collapse
I'm so sorry that was so dumb of me, obviously it will not detect because you have a LG Device And ODIN is SAMSUNG handsets only.
you can factory reset your phone, just follow this tutorial:
https://www.youtube.com/watch?v=3ogBvzbPikc
abhinavp649 said:
I'm so sorry that was so dumb of me, obviously it will not detect because you have a LG Device And ODIN is SAMSUNG handsets only.
you can factory reset your phone, just follow this tutorial:
https://www.youtube.com/watch?v=3ogBvzbPikc
Click to expand...
Click to collapse
Tried - dint work, as i i mentioned earlier this key combination is not working though Volume down button works.
Guys, any suggestion? or any method to wipe or restore?
please advice.
akshayhgd said:
Guys, any suggestion? or any method to wipe or restore?
please advice.
Click to expand...
Click to collapse
I don't know why the Recovery Combination isn't working.
The last option is left to take your phone any service center and let them do the technical work. and also ask them a way to access recovery.