Hey all,
I am trying to get Cyanogen 12.1 running on a X10 tablet which uses a allwinner a83t chipset. They have not released their full kernel source so I am using the original kernel. Currently I am getting hung up on the build, but I cant pinpoint which error is holding android from booting. Is anyone who knows more about the android boot process able to identify where I am getting held up. I am able to adb in once it hangs and it looks like the filesystem has mounted properly.
I cant fit it into the post due to wordcount limit, so off to pastebin.
Thanks.
Related
I compiled JB 4.1.2 for my device. It compiled perfectly after fixing the device tree and adding new variables that it needed for JB. I had to use the 2.6.34 kernel as there was not enough information to easily port to 3.0.
Anyway, it flashed well. But, it will not load.
1. I see the logo displayed per uboot (logo.bmp)
2. I see the droid which is the init logo.
3. If this were like ICS, I would get the bootanimation.zip next. However, this goes to a blank screen.
It never comes up to load after the blank screen.
There isn't much in the way of ADB without WiFi unfortunately.
Any thoughts? I really could use some debugging help.
Hello everyone,
Here is my problem of which I hope you can help me out.
I own a Allwinner A13 7 inch tablet, on which I installed the Cyanogen 10 mod (Due to restrictions I cannot place the link to the mod)
The problem is I probably installed the wrong touchscreen driver, so the tablet boots perfectly into the Mod but I can't do anything.
Normally it would be no problem to just put back my backup, but I can't get it to boot into CWM.
In the first place I rebooted into CWM to instal the mod by adding the following command through the "terminal app" before rebooting,
Command: "echo -e 'boot-recovery\0' > /dev/block/nandf; sync"
Now I cannot use the screen so i cant use the terminal.
I also cannot use ADB because USB debugging is standard switched of after flashing a new MOD.
Does anyone know if there is another way to get into CWM??
Thanks a LOT!
Thanks a lot!
I will have a look
Do you by change know where to get a working stock rom? I flashed one which i found using google a couple of times but it only results in a Boot loop (I have no luck at all!).
Thanks!
Update: found a stock version that works. But no my touchscreen is inverted.
Also I probably made another **** up, because I accepted the format option of Livesuit, so now I lost my backup.....
Hello guys
I have an HP 10 tablet running 4.4.2. It is rooted, but I haven't updated due to the ota,not recognizing the root. I wanted to update to lollipop, but couldn't find specific roms for may model. I saw some HP touch stuff. This is a quad core 1.2ghz, ARM v7 processor rev 3 (v71). since rooting it o longer keeps its state, and if it goes dead, is turned off, or reboots, it defaults to factory settings, and I have to start all over with installing my back up. it is time to update andf make more stable. any help?
Root
How did your obtain root??
Hello everyone,
I am new to xda and also started working with the android research some months ago, i used to work with linux and IT secirity(enthusiasm) but haven't been intouch with from a long time, now thought to have kali in pocket, so now i have proceeded from TWRP to nethunter chroot, but stuck with the nh_terminal, the no title problem, i searched a lot about it, tried the new installers creating symlinks to /system/bin etc, but still no success, moreover my device is qmobile noir x35(rooted,TWRP,backedup), kernel v3.4.67, oh and the roms that i tried were official .zip from offensivesecurity( nexus4 n oneplus one). Can someone help me with this , or may be show another way which might work. Thanks
Good Evening,
I have an old HP Elitepad 1000 G2 tablet I have been trying to install Android x86 on..
I have tried both Android-x86 7.1 and CM-x86 14.1 installers listed on android-x86 <dot> org
it appears to run stable for the most part, and most of the minor issues I have been able to fix without issue.. however, anytime I try and manually put the device in sleep mode it just powers off. in the case of entering sleep mode from remaining idle, it will instead reboot itself.
anyone experience this and know of some possible work arounds?
any ideas?