Phone will not switch on or charge up.
djc1232 said:
Phone will not switch on or charge up.
Click to expand...
Click to collapse
is it detected by sp flash tools? if yes reflash stock rom, if still doesnt work, what did you made for it to brick? it might be a dead battery, use usb in pc and leave it there, it charges slower which sometimes work to recharge batteries that went fully to 0%
If nothing helps, contact your seller for a warranty claim.
Jesus, these threads nowadays...
You have to download the latest stock rom, connect your phone to sp flash tool and flash. If sp flash tool does not recognize your smartphone, you have to check that you have downloaded the correct driver for sp flash tool. After that, select Format & Download, then start formating & flashing and press the louder key until sp flash tool shows a reaction.
Im sorry for my bad english
Related
Hi, I have the phone Zopo C2. I turned off the phone and stopped responding. When connected to the charger, nothing happens. When connected to a computer is detect normally, I can flash ROM by SP flashtool. And here is the problem, as long as I want toflash, reaches the first red bar to 100% and ends flash without error. Drivers have a good, first is connected as "USB PORT MTK" and how it comes to 100% red bar that goes in the "VCOM MTK DOWNLOAD".I have a second phone zopo c2 and there I normally flash, and everything goes without problems
I tried with the removed battery inserted, all methods and nothing, always the same 100% red stripe and the end of the flash without any error.
I wanted to flash such proloader same and is the same.
Phone is brick ? Memory in phone is dead or what ?? Can still fix it?
Sorry I from Poland and my english is very bad.
Uninstall all VCOM drivers.
restart PC and reinstall them.
Open SPFlash Tools, choose full speed and W/O Battery
Connect phone to PC.
If flash start, ok, if not, take out the battery and put it back again. Repeat if necessary.
PMoto said:
Uninstall all VCOM drivers.
restart PC and reinstall them.
Open SPFlash Tools, choose full speed and W/O Battery
Connect phone to PC.
If flash start, ok, if not, take out the battery and put it back again. Repeat if necessary.
Click to expand...
Click to collapse
I try on three PC. Always this same, flash start(100%red bar) and end, nothing more.
Any error. :crying:
any possible faulty memory?
Ok then, do like I post, but select only the preloader.
Then, restart all over again...
Hello
Every thing was good until I decided to port a ROM for my phone
I ported it with kitchen then flashed it via SP Flash Tools. The process completed without any error. After that I tried to turn on my phone but it didnt, and my phone was completely dead and now nothing is working(The screen is black,device doesnt charge,recovery doesnt come up and even dosent conect to PC) .
I tried this trick but it didnt work too
http://forum.xda-developers.com/showthread.php?t=1943442
Because PC can not recognize the phone and when I conect the cable to the computer nothing happens. I tried differnet keys but none of them worked
The port Rom was canvas A1 4.4.4 with an odd preloader and my phone is a chinces phone with mt6582 chip (GFIVE President Classic 9).
Is there any other way to revive this phone?
thanks
Ok first you wanna download your stock rom from needrom.com...then flash it with sp tools..if this doesnt work cause sp tools isnt regognising your phone,take out your phones battery and connect it pressing the vol down button(in case it is always disconnecting itself)..ok now, open sp flash tool,take the scatter file from the rom you just downloaded and extracted...press download,connect your phone without battery and you are done!!
Godlike12 said:
Ok first you wanna download your stock rom from needrom.com...then flash it with sp tools..if this doesnt work cause sp tools isnt regognising your phone,take out your phones battery and connect it pressing the vol down button(in case it is always disconnecting itself)..ok now, open sp flash tool,take the scatter file from the rom you just downloaded and extracted...press download,connect your phone without battery and you are done!!
Click to expand...
Click to collapse
As I said it doesnt work...
The PC can not recognize the phone therefore flashing is impossible...
What can I do?
FLASHED 2.DUMP_ROM [SPFT][ROOTED] FROM All About CherryMobile Flare 4 AFTER IT SAYS FLASHING IS DONE 100% WITH CHECK MARK THEN MY PHONE DIDNT RESTART I WAITED FOR ABOUT 15 MINUTES TO SEE IF THERE'S SOMETHING MIGHT HAPPEN BUT NOTHING ONLY BLACK..
SO I PULLED THE USB CONNECTOR, THEN PLUG IT BACK. THE ONLY THING THAT I SAW IS UNRECOGNIZED USB. NO CHARGING LOGO OR ANDROID OR ANYTHING EVEN THE LED INDICATION OF CHARGING IS NOT BLINKING.
I HOPE SOMEONE CAN HELP ME :crying::crying::crying::crying::crying::crying::crying:
UP
I also had the same problem and I also cried. Your phone have MediaTek MT6753 Chipset. I have MT6582. You flashed ROM via recovery and looks like ROM have conflict with bootloader.
SP Flash Tool can flash shutdown MTK devices via USB. Your computer show "UNRECOGNIZED USB". SP Flash Tool need special ROM and driver to find your phone. Not sure, that SP Flash Tool can help you, but it helped me.
How I decided problem:
I waited some time (I went sleep, it was night)
Found stock ROM for Flashtool. This ROM contain all data for device and have more size.
Install driver for my phone.
Pulled out battery.
Connect with computer via USB.
Put in battery and computer detected phone as "MediatekDevice". SP Flash tool also detected phone
Started flashing.
Good luck!
AlexanderBabansky said:
I also had the same problem and I also cried. Your phone have MediaTek MT6753 Chipset. I have MT6582. You flashed ROM via recovery and looks like ROM have conflict with bootloader.
SP Flash Tool can flash shutdown MTK devices via USB. Your computer show "UNRECOGNIZED USB". SP Flash Tool need special ROM and driver to find your phone. Not sure, that SP Flash Tool can help you, but it helped me.
How I decided problem:
I waited some time (I went sleep, it was night)
Found stock ROM for Flashtool. This ROM contain all data for device and have more size.
Install driver for my phone.
Pulled out battery.
Connect with computer via USB.
Put in battery and computer detected phone as "MediatekDevice". SP Flash tool also detected phone
Started flashing.
Good luck!
Click to expand...
Click to collapse
thanks bro.
now it show dram fail (4032)
i was trying to flash stock rom to my infinix x551 by sp flashtool everything were great until i accidentally unplugged the phone
tried to retry to flash it again with no hope
it doesn`t open recovery mode or switching on
only when i plug it to the pc i hear a voice from it then nothing happens
Remove the battery and then try to plug the phone into sp flash tools
Adithya FRK said:
Remove the battery and then try to plug the phone into sp flash tools
Click to expand...
Click to collapse
my phone battery is built in i can`t remove it
Did you try to flash the bootloader at first? It is not recommended to do that.
Hi more one time...
Unfortunately I made a big mistake because while I was flashing rom, I ended up removing my cell from the USB cable, now my cell phone is not recognized by the SP Tool not flash, and I just can not flash anything else ...
Is there anything that can be done, or is my cell phone dead?
(My PC reconize when I plug the phone P9000 on USB, but flash tool doesn't)
Disconnect the battery by removing the back case and then connect​ it and then flash original rom
haidar123 said:
Disconnect the battery by removing the back case and then connect​ it and then flash original rom
Click to expand...
Click to collapse
Thank you so muchhhh!!!!
It's done :good::good::good::good::good: