No charging LED / No Boot after official PLK-L01_C432B380 Update - Honor 7 Q&A, Help & Troubleshooting

Hello Everybody! First of all sorry for my bad englisch.... I have a Honor 7 with TWRP 2.8.7.0 5.0-6.0 EN. It had the factory Firmware with EMUI 3.1 Now I ´ve searched in my Honor 7 update Program for new firmware and it found the PLK-L01_C432B380. After downloading it I´ve clicked on install. The phone has shut down and the TWRP has opened. Than it installed a couple of files and without any success Message the Phone turns off. Now I can´t turn it on. Not in Fastboot mode and not in Recovery Mode. I´ve i try to connect it to the PC or try to charge it the charging LED don´t work. Only if I press the Power Button for more than 10 seconds a short vibration comes but nothing happens. I have any changes to get the phone on? The Battery is fully loaded.
Thanks Guys

gremlin1987306 said:
Hello Everybody! First of all sorry for my bad englisch.... I have a Honor 7 with TWRP 2.8.7.0 5.0-6.0 EN. It had the factory Firmware with EMUI 3.1 Now I ´ve searched in my Honor 7 update Program for new firmware and it found the PLK-L01_C432B380. After downloading it I´ve clicked on install. The phone has shut down and the TWRP has opened. Than it installed a couple of files and without any success Message the Phone turns off. Now I can´t turn it on. Not in Fastboot mode and not in Recovery Mode. I´ve i try to connect it to the PC or try to charge it the charging LED don´t work. Only if I press the Power Button for more than 10 seconds a short vibration comes but nothing happens. I have any changes to get the phone on? The Battery is fully loaded.
Thanks Guys
Click to expand...
Click to collapse
Im in the same boat, and as far as i can get is to Hope for servicecenter replacement... Og did u get it to Work again?

HonorCasper said:
Im in the same boat, and as far as i can get is to Hope for servicecenter replacement... Og did u get it to Work again?
Click to expand...
Click to collapse
Hello Casper! Unfortunately I found no way to run the Phone. I´ve send it to Honor and got it back after only two days!! They changed the main board. Now everything works.

gremlin1987306 said:
Hello Everybody! First of all sorry for my bad englisch.... I have a Honor 7 with TWRP 2.8.7.0 5.0-6.0 EN. It had the factory Firmware with EMUI 3.1 Now I ´ve searched in my Honor 7 update Program for new firmware and it found the PLK-L01_C432B380. After downloading it I´ve clicked on install. The phone has shut down and the TWRP has opened. Than it installed a couple of files and without any success Message the Phone turns off. Now I can´t turn it on. Not in Fastboot mode and not in Recovery Mode. I´ve i try to connect it to the PC or try to charge it the charging LED don´t work. Only if I press the Power Button for more than 10 seconds a short vibration comes but nothing happens. I have any changes to get the phone on? The Battery is fully loaded.
Thanks Guys
Click to expand...
Click to collapse
just remember DO NOT install emui updates in twrp , never do that.. emui updates should be installed when you are not using twrp..

I endes Up sending mine to the store where i bought it and they changed the Main curciuit board..

Related

Hardbrick??!

Hi everybody, i need your help, yesterday i had a problem with mateo's unofficial cm10.1, after a reboot the phone freezes at LG logo, and if i try to get into the recovery it doesnt work cause it is writtene in the bottom "E: Can't mount /cache/recovery/command" and i do not have any button to select. So i try to go in SW Upgrade Mode but the pc is not able to recognize my phone like always did, i installed latest version of drivers but no way. In Lg mobile support tool doesnt work (look to te attached file). Any help?? :'(
Thanks in advance
Roker1 said:
Hi everybody, i need your help, yesterday i had a problem with mateo's unofficial cm10.1, after a reboot the phone freezes at LG logo, and if i try to get into the recovery it doesnt work cause it is writtene in the bottom "E: Can't mount /cache/recovery/command" and i do not have any button to select. So i try to go in SW Upgrade Mode but the pc is not able to recognize my phone like always did, i installed latest version of drivers but no way. In Lg mobile support tool doesnt work (look to te attached file). Any help?? :'(
Thanks in advance
Click to expand...
Click to collapse
But you get to S/W Upgrade Mode or not? If yes try diffrent computer too.
I am able to go in SW upgrade mode, but after 2-3 minutes the phone get off, i think the battery is out, is it possible? How can i charge it? The charge from phone turned off doesnt work in my last rom
Roker1 said:
I am able to go in SW upgrade mode, but after 2-3 minutes the phone get off, i think the battery is out, is it possible? How can i charge it? The charge from phone turned off doesnt work in my last rom
Click to expand...
Click to collapse
I think in that case you would need another working device to charge your own battery.

stuck on elephone logo

The phone told me there was a new update I started to install it, got to reboot and now is just on the elephone logo which comes every 20 sec and goes again. I cannot turn the phone off or do anything with it. Any help please
For me just shut down the phone and then reiniciat the phone ....work for me....
Enviado do meu thor através de Tapatalk
same problem here.. wtf nice update elephone, we cant be the only ones right?
now stuck on logo, restarting every 3 seconds with 100% battery...i m not even sure it will work again if battery is drained out
i can do nothing, no trys to get in factory mode or shut the phone down worked..
stuck on elephone log after upgrade
My elephone P9000 is now cycling the elephone logo every 8 seconds or so after the latest audio upgrade... It will not switch off or do anything else. Did you solve the problem. Or anyone else help. Can you share with me? Thank you.
same problem here.. wtf nice update elephone, we cant be the only ones right?
now stuck on logo, restarting every 3 seconds with 100% battery...i m not even sure it will work again if battery is drained out
i can do nothing, no trys to get in factory mode or shut the phone down worked..
Click to expand...
Click to collapse
so my battery was fully empty now.. i even pressed the power button 100 times after the battery was empty, to make sure all current is out of the phone.
plugged in charger... after 10 seconds phone start itself (after viewing the picture of empty battery) and elephone logo shows short and then back to showing picture of empty batterie cycle. After some minutes, and battery is loaded a little bit, elephone logo cycles again.
So rest in piece my p9000, i can nothing, i cant do anything from my pc because its only starting for like 5 seconds, i cant shut it down because of that and i cant get in factory mode
i am so pissed right now
just wanted to install the new update, everything worked fine like all the times before that and now my phone is ready for the trashcan.
Is there any way to reset the software without getting in factory mode?
Reset from sp flash tools?
Pro4TLZZ said:
Reset from sp flash tools?
Click to expand...
Click to collapse
the phone turns on and off in a cycle of 5 seconds, so that wont work
and i cant stop that cycle.
even if battery is 0% (i even press power button many times so really its drained out). If i recharge it, the cycle starts again without me doing anything. The Power button is not broken or something. it all began after i started new ota update and the phone rebooted like "mkitty" has the same problem it seems
Same for me, I have no idea how to restart my phone. And i dont want to loose all data I have on it.
have you tried to hold the volume up and power at the same time during the restart process to try and force recovery?
xvicedice said:
have you tried to hold the volume up and power at the same time during the restart process to try and force recovery?
Click to expand...
Click to collapse
Hello,
Yes . I have tried that.
I have a list of options that come up on the screen.
I have tried them apart from the wipe data/factory reset.
But it is still the same result.
Thank you for help.
Any more ideas?
what OTA update version did you update?
Simplytouched said:
what OTA update version did you update?
Click to expand...
Click to collapse
It said something about wifi and audio update. I followed the instructions as per a previous update (which worked OK). I never took notice of any version numbers etc.
I have all I need to flash a new rom to the bricked phone but when I connect the off phone to my pc the usb not recognised comes up and I cannot flash the rom to the phone. and yes I have the mediatek vcom drivres install. Why did I buy a Chinese phone elephone p9000 please stay well away from it. on paper is a great phone but in reality does not perform in any sense, battery only lasts 7 hours if I was lucky camera crap, gps works most of the time all that ram and power and t struggles with some videos o dear god. never again. now I cannot even read what I have on the sd cos is formatted for the phone.
juka1 said:
I have all I need to flash a new rom to the bricked phone but when I connect the off phone to my pc the usb not recognised comes up and I cannot flash the rom to the phone. and yes I have the mediatek vcom drivres install. Why did I buy a Chinese phone elephone p9000 please stay well away from it. on paper is a great phone but in reality does not perform in any sense, battery only lasts 7 hours if I was lucky camera crap, gps works most of the time all that ram and power and t struggles with some videos o dear god. never again. now I cannot even read what I have on the sd cos is formatted for the phone.
Click to expand...
Click to collapse
Its actually a great phone. Do you have twrp installed and can you get access to it? You could always boot into twrp transfer over the ROM and install it from there. If you have installed the vcom drivers then when the USB not recognized alert pops up. Go to settings and device manager. Right click the unknown device and click let me pick driver. You should be able to install it from there
The only thing I can suggest is to take the back panel of and unplug the battery. There videos on how to do this if you search YouTube or the forum. Effectively you perform a hard reset of the phone.
If and when you do get it working just twrp installed and do a backup of the whole phone working before performing any future upgrades or Rom changes. Its just better safe then sorry.
thenk you very much for that
The problem is that when I connect the phone on the off to the pc starts again the cycling through the elephone logo so the pc sees the phone for a few seconds in which does not recognises it and then is like the phone goes off until the next cycle so no time to go to device manager and install manually. but thank you for the comment.
removing the battery will void the warranty. I had the phone only since may.
It's unlikely it really matters. Your phone seller not going to take it back or fix it for free just because it's bootlopping. Well they may so just ask them. If you can't get it into recovery then a battery disconnect or contact your seller are your options
thank you
Android-UK said:
It's unlikely it really matters. Your phone seller not going to take it back or fix it for free just because it's bootlopping. Well they may so just ask them. If you can't get it into recovery then a battery disconnect or contact your seller are your options
Click to expand...
Click to collapse
I can get it into recovery mode but I haven't got any software install in the sd card to do a recovery that is why I thought my only option was the sp flashing tool and the room which I have
juka1 said:
I can get it into recovery mode but I haven't got any software install in the sd card to do a recovery that is why I thought my only option was the sp flashing tool and the room which I have
Click to expand...
Click to collapse
Well in that case all you need is a stock rom and yes just flash them with sp tools and it should start booting again. The fact you can get to recovery is a good sign.
Android-UK said:
Well in that case all you need is a stock rom and yes just flash them with sp tools and it should start booting again. The fact you can get to recovery is a good sign.
Click to expand...
Click to collapse
sorry for all of this and thank you very much for your help but when I put the phone in recovery mode by pressing the down volume and power key and connect the phone to the pc it is not recognized by the pc so I can't flash the room

HELP:Honor Hard bricked: Bootloop stuck at booting now screen only fastboot

Hello guys,
so I had installed RROS 8.1 on my Honor 9 STF-L09, but capacitive buttons and flashlight didn't work, so i decided to roll back to B120 via HWOTA in recovery, I think I chose a wrong stock recovery image so there went something wrong and the phone won't boot up..
It was stuck at the Bootloader unlocked - Your device is booting now... screen, I only can access fastboot mode.
I've already tried every unbrickng method I know. First I tried to unbrick it via Multitool and stock firmware and recovery but this didn't help, I did just get another screen where I was stuck(Error mode: func11: recovery , load failed or sth like that). I also tried flashing TWRP but it doesn't work, it says it was successfully installed, just like with multitool, but i am still stuck. Also tried flashing Stock recovery image and then using dload sd card method but it won't even go to Emui restoring screen.. I actually just tried to flash all the important image files from update.APP (which I know how to flash via fastboot), but it didn't do anything. After trying again via Multitool I am again stuck at the 'unlocked screen'.
If somebody could help i would be so thankful, I don't know what to do now.. THANK YOU
Sorry for my bad english I am a student from germany
Lord Juggelmann said:
Hello guys,
so I had installed RROS 8.1 on my Honor 9 STF-L09,
Click to expand...
Click to collapse
Which region ? C432 ?
Which version B36x ?
Lord Juggelmann said:
but capacitive buttons and flashlight didn't work, so i decided to roll back to B120 via HWOTA in recovery,
Click to expand...
Click to collapse
With which HWOTA ? 'HWOTA 8 to 7 rollback' ?
Lord Juggelmann said:
I think I chose a wrong stock recovery image
Click to expand...
Click to collapse
Which one ?
oslo83 said:
Which region ? C432 ?
Which version B36x ?
With which HWOTA ? 'HWOTA 8 to 7 rollback' ?
Which one ?
Click to expand...
Click to collapse
Yes, C432, i installed it on B363 bur don't know if it was the same at RROS.
Now that you ask I'm not that sure it could also have been the mistake that I maybe used HWOTA7 which I used to upgrade to Oreo B363. I tried to rollback to B130.
It was a STF_RECOVERY_NoCheck.img Recovery I think it actually was the Nougat version but could have also been oreo...
Thanks for replying btw
Try to install TWRP from this thread:
https://forum.xda-developers.com/showpost.php?p=75680308
Dpesnit install successfully ? Can you boot twrp now ?
oslo83 said:
Try to install TWRP from this thread:
https://forum.xda-developers.com/showpost.php?p=75680308
Dpesnit install successfully ? Can you boot twrp now ?
Click to expand...
Click to collapse
Installed successfully but still same result, can't boot into recovery..
You are trying with usb unplugged and with vol+ button ?
oslo83 said:
You are trying with usb unplugged and with vol+ button ?
Click to expand...
Click to collapse
Everytime I try to do without usb plugged I will get a red sign with a lightning that tells me battery is empty, this won't change if I charge it, could be an error but also could have to do something that it always stays on this booting now screen when plugged in and not in fastboot mode. Actually this Battery sign pops up everytime I shut it down when I try to boot(just not with fastboot), even if plugged in but then it works after a few seconds. I asked Multitool for Battery voltage in fastboot and got this answer: ...
(bootloader) 5298mv
OKAY [ 0.012s]
finished. total time: 0.020s
Btw I just noticed that in stuck screen red led lights up like every 2-3sec
Thank you for the fast answer
Leave the phone overnight (around 12 hours) to be charged with the original charger then try again on the computer
to restore it.
It happens to myself with a Motorola phone years ago.
mihaidenis said:
Leave the phone overnight (around 12 hours) to be charged with the original charger then try again on the computer
to restore it.
It happens to myself with a Motorola phone years ago.
Click to expand...
Click to collapse
I will try, what type of restoring do you mean?
Edit: Didn't work for me.. Still tells me battery is empty. I think it has to be a software issue or so:crying:
You can restore it using a paying software called DC-Phoenix.
I own a license, PM me if you need further help.

After install new EMUi 9.1, my Honor 9 went to bootloop and I can not escape

Good Morning,
Friday night I downloaded the new EMUI 9.1., the official version, and I installed it during the night.
I used my phone all the Saturday but it was extremly slow. I swiched off my phone several times but it never helped me.
At some point in the afternoon, the phone is reseted alone and I have not been able to use it anymore.
The phone only resets itself: it turns on, reaches the blue screen that says "Honor" and resets again. It can not be turned off.
I tried to do a HW reset (power off + volume up) but nothing happens: it reaches the blue screen and it resets again, and again and again...
The only interaction I can have is with the "Fastboot & Rescue mode" screen. Here I get the error: AP_S_Abnormal 64.
Phone Locked FRP lock.
And nothing more.
Would someone be so kind to help me or give me some recommendation/advice of what I can do?
Thank you
From where did you get EMUI 9.1?
I think he meant 9.0 and not 9.1
Soforid said:
Good Morning,
Friday night I downloaded the new EMUI 9.1., the official version, and I installed it during the night.
I used my phone all the Saturday but it was extremly slow. I swiched off my phone several times but it never helped me.
At some point in the afternoon, the phone is reseted alone and I have not been able to use it anymore.
The phone only resets itself: it turns on, reaches the blue screen that says "Honor" and resets again. It can not be turned off.
I tried to do a HW reset (power off + volume up) but nothing happens: it reaches the blue screen and it resets again, and again and again...
The only interaction I can have is with the "Fastboot & Rescue mode" screen. Here I get the error: AP_S_Abnormal 64.
Phone Locked FRP lock.
And nothing more.
Would someone be so kind to help me or give me some recommendation/advice of what I can do?
Thank you
Click to expand...
Click to collapse
So because :
- your device reboot itself to bootloader mode because 'AP_S_Abnormal 64'
- Phone is Locked FRP lock
- you don't manage to enter recovery mode to do a full wipe / factory restore
You could :
- download and use a dload package with an sd/card or an USB-OTG flashdrive in dload mode.
- or use Honor service center help
- or try again and again to boot right to recovery mode to format.
- or try erecovery restore via wifi in erecovery mode
- or try Hisuite Restore option
I think they all will restore your device to factory stock, meaning the actual user datas would be lost...
---------- Post added at 14:51 ---------- Previous post was at 14:45 ----------
Pro tips to enter recovery mode :
-USB must be unplugged (not plugged to computer)
-Hold VolumeUp key BEFORE device vibrate first at boot and keep holdind UNTIL you are in recovery mode
-Try again to reach 'recovery mode'
the pie update has been pulled because of the recovery error , have a google about it
The Mero said:
the pie update has been pulled because of the recovery error , have a google about it
Click to expand...
Click to collapse
Google heard nothing about that here...
oslo83 said:
Google heard nothing about that here...
Click to expand...
Click to collapse
https://uk.community.huawei.com/honor-phones-34/honor-9-stuck-on-erecovery-loop-after-emui-9-official-update-4340
https://uk.community.huawei.com/software-40/load-honor-screen-after-reboot-stf-l09-9-0-1-162-c432e2r1p5-4131
https://translate.google.co.uk/translate?hl=en&sl=it&u=https://www.optimagazine.com/2019/04/26/scelta-estrema-per-honor-9-aggiornamento-con-emui-9-e-stato-ritirato-per-i-suoi-problemi/1444771&prev=search
Google is your friend
I updated to 9 through hisuite because no OTA update was found . tried it and rolled back to 8 cause they removed image stabiliser fron video recording . I read somewhere else that the update was pulled cause so many were having issues , but i always do a hard reset after updating and had none of the issues described , guess i was lucky.
The Mero said:
https://uk.community.huawei.com/hon...covery-loop-after-emui-9-official-update-4340
Google is your friend
I updated to 9 through hisuite because no OTA update was found . tried it and rolled back to 8 cause they removed image stabiliser fron video recording . I read somewhere else that the update was pulled cause so many were having issues , but i always do a hard reset after updating and had non of the issues desribed .
Click to expand...
Click to collapse
If you say so.
So we should think B162 erecovery is not pushed anymore ?
oslo83 said:
If you say so.
So we should think B162 erecovery is not pushed anymore ?
Click to expand...
Click to collapse
Yeah it looks like it was a bit of a mess so just have to keep checking if they release an update for the update lol

Unable to boot

Hello !
So 2-3 months ago I flashed my phone and installed Lineage OS, everything was working perfectly
But today, I was on Snapchat sending a message and my phone turned off for no reason, I tried turning it on, I get the message that my device is untrusted as usual, Sony logo, then it crashes and shutdown.
I tried to boot on recovery mode with TWRP but it won't and crashes.
I also noticed that when I turn on my phone I sometime get a weird pattern on the screen, just like when a GPU is dead on PC.
Anyone has also encountered this problem ? If so, is there a way to fix it ? I don't mind turning back to stock OS as long as it works again.
Thanks for your help !
Alright, so I had some ideas but none of them worked :
- Using XperiaCompanion (Since I unlocked the bootloader it can't help)
- Tried plugging the phone to my pc while holding power down, used ADB, listed devices but it doesn't show up
Is my phone bricked ?
Try flashing stock firmware using Flashtool or Emma.
iH8Ecchi said:
Try flashing stock firmware using Flashtool or Emma.
Click to expand...
Click to collapse
It works ! Thanks a lot, you've just made my day !

Categories

Resources