I am using TWRP 3.0.2.0 It is giving me problems as shown in images below.
I tried flashing new recovery but it also couldn't get flashed. While flashing new CM 13/CM14.1 ROMs it is giving errors, but it flashes older CM 13 ROMs fine.
dvaibhavd said:
I am using TWRP 3.0.2.0 It is giving me problems as shown in images below.
I tried flashing new recovery but it also couldn't get flashed. While flashing new CM 13/CM14.1 ROMs it is giving errors, but it flashes older CM 13 ROMs fine.
Click to expand...
Click to collapse
Bro wait....!!!
Is this real?
You are using too old recovery(as your ss says 2.8.7)+old boot loader..you need some work on your phone to be able to flash new cm 13/14.1.
Just head over to general thread and find how to upgrade boot loader and install latest twrp.
After that you can flash all latest available ROM.
Boot logo Problem
Hey I have used this method http://forum.xda-developers.com/one...update-bootloader-firmware-to-t3478917/page20 and updated the BL.However after flashing CM14 I am stuck on 1+ logo.
I was able to flash stock Oxygen Rom .I want to flash CM 14 please help
Same
utkhirodka said:
Hey I have used this method http://forum.xda-developers.com/one...update-bootloader-firmware-to-t3478917/page20 and updated the BL.However after flashing CM14 I am stuck on 1+ logo.
I was able to flash stock Oxygen Rom .I want to flash CM 14 please help
Click to expand...
Click to collapse
Same here with the TZ issues. As for the recovery, the TWRP version 3.0.2-0 is the most latest one that I can flash & boot into successfully. If I flash anything newer than 3.0.0-1 my OPX is stuck on OP logo as well.
My phone is stuck at one plus boot logo when i tried to go into recovery mode or tried to start it the oneplus logo popped and goes out again and again and when i tried to flash twrp through fastboot mode it say the device is locked cant change or erase the recovery what should i do please guide me
The only recovery that will flash on mine is 3.0.2-0. I've tried flashing through Fastboot. I've even tried to use the dd command for both 3.0.3-0 official and blu sparkz v41 and it gets stuck at the OnePlus logo.
Phone still boots into OOS just fine and 3.0.2-0 flashes through the old JMZ TWRP app just fine. It's just any other method that doesn't work.
The latest recoverys for new bootloader is 3.0.3, bluesparks 3.0.2-1 V41 or Sultans updated TWRP. 3.0.2 and under us for old bootloader.
Exodusche said:
The latest recoverys for new bootloader is 3.0.3, bluesparks 3.0.2-1 V41 or Sultans updated TWRP. 3.0.2 and under us for old bootloader.
Click to expand...
Click to collapse
Again, I tried flashing 3.0.3 and it wouldn't stick.
blackknightavalon said:
Again, I tried flashing 3.0.3 and it wouldn't stick.
Click to expand...
Click to collapse
After flashing recovery you have to boot right into it with fastboot command then swipe to allow modifications?
Exodusche said:
After flashing recovery you have to boot right into it with fastboot command then swipe to allow modifications?
Click to expand...
Click to collapse
As stated above, all it does is hang at the OnePlus logo.
Also...
fastboot boot drive:\path\to\twrp-3.0.3-0-onyx.img
downloading 'boot.img'...
OKAY [ 0.507s]
booting...
FAILED (remote: dtb not found)
finished. total time: 0.540s
Click to expand...
Click to collapse
blackknightavalon said:
As stated above, all it does is hang at the OnePlus logo.
Click to expand...
Click to collapse
Ok sorry what I did was keep it simple. Reflash original stock recovery, flash 2.2.3 then flash 3.1.4 and boot. Just skip everything and reboot back to bootloader mode. Now you can flash latest TWRP and should boot latest ROMs without any issues.
Exodusche said:
Ok sorry what I did was keep it simple. Reflash original stock recovery, flash 2.2.3 then flash 3.1.4 and boot. Just skip everything and reboot back to bootloader mode. Now you can flash latest TWRP and should boot latest ROMs without any issues.
Click to expand...
Click to collapse
2.2.3 flashed successfully. I already know 3.1.4 will work. I'll post again if your plan completely works.
...and I'm still getting the same errors after flashing 3.1.4 through stock recovery. o.0
I'm going to start from the earliest firmware available and flash progressively from there and see if that works.
Related
While H2OS was loaded, I flashed TWRP. After that I rebooted to recovery, cleared all the essential things, flashed a ROM followed by a Gapps package. After that, when I chose reboot to system, the phone stays stuck at the OnePlus logo screen. I can't access the recovery either. I flashed 3 different versions of TWRP, but still couldn't boot to recovery. P.S.: Bootloader is unlocked
What can I do now?
UPDATE: BluSpark's modded TWRP works, but after flashing the ROM nothing boots
meraj99 said:
While H2OS was loaded, I flashed TWRP. After that I rebooted to recovery, cleared all the essential things, flashed a ROM followed by a Gapps package. After that, when I chose reboot to system, the phone stays stuck at the OnePlus logo screen. I can't access the recovery either. I flashed 3 different versions of TWRP, but still couldn't boot to recovery. P.S.: Bootloader is unlocked
What can I do now?
UPDATE: BluSpark's modded TWRP works, but after flashing the ROM nothing boots
Click to expand...
Click to collapse
You should fastboot flash old OOS 2 stock recovery, then full OOS 2.2.2 Rom.
Then root and install offical TWRP (not BS V41).
Then install what you want (but not Oxygen or hydrogen on MM)
Kéno40 said:
You should fastboot flash old OOS 2 stock recovery, then full OOS 2.2.2 Rom.
Then root and install offical TWRP (not BS V41).
Then install what you want (but not Oxygen or hydrogen on MM)
Click to expand...
Click to collapse
oh, root access is compulsory?
Just tinking about root, because I used it to install TWRP but you're right, fastboot flash could do it
Hello guys
I was on stock android and stock recovery oos 3.1.3. I tried to change recovery using fastboot so i tried so many recovries, but unable to flash anyone then i found twrp recovery by teamspark so i flashed it and successfully done, but problem with it is, i am not able toh flash paranoid rom and stock rom using this recovery and even the stock recovery is also not flashable now, just stuck on logo whenever i flash stock recovery. So which recovery i can use which can correctly flashable and i can flash paranoid rom by that successfully.
Thanks in advance.
Flash old stock recovery followed by any OOS 2.X.X firmware . Now you can proceed with PA. Note dont use any of the twrp's designed for mm bootloader.
Rajatdembla said:
Hello guys
I was on stock android and stock recovery oos 3.1.3. I tried to change recovery using fastboot so i tried so many recovries, but unable to flash anyone then i found twrp recovery by teamspark so i flashed it and successfully done, but problem with it is, i am not able toh flash paranoid rom and stock rom using this recovery and even the stock recovery is also not flashable now, just stuck on logo whenever i flash stock recovery. So which recovery i can use which can correctly flashable and i can flash paranoid rom by that successfully.
Thanks in advance.
Click to expand...
Click to collapse
First of all, you have to downgrade your bootloader. Then you can flash any recovery for the old bootloader.
Thanks i m done now
Exodusche said:
Flash old stock recovery followed by any OOS 2.X.X firmware . Now you can proceed with PA. Note dont use any of the twrp's designed for mm bootloader.
Click to expand...
Click to collapse
Thank you so much brother now i m able to flash.
My phone stucks on oneplus logo after flashing paranoid rom . I do everything like wiping dalvin cache, data , system . TWRP recovery i am using is 3.03 and currently running cm 13. Any solution?
Mandeep Singh 07 said:
My phone stucks on oneplus logo after flashing paranoid rom . I do everything like wiping dalvin cache, data , system . TWRP recovery i am using is 3.03 and currently running cm 13. Any solution?
Click to expand...
Click to collapse
Is ur bootloader updated to latest one ??
[email protected] said:
Is ur bootloader updated to latest one ??
Click to expand...
Click to collapse
yeah its latest one 3.0.3
Mandeep Singh 07 said:
yeah its latest one 3.0.3
Click to expand...
Click to collapse
PA I believe is on the old bootloader still. So you would have to downgrade your bootloader by flashing LL stock recovery and 2.x.x OOS firmware. Not worth the hassle if you ask me.
Mandeep Singh 07 said:
yeah its latest one 3.0.3
Click to expand...
Click to collapse
actually when i root the phone , then it goes into bootloop, i didn`t backup my data so i lost my all data ,
after that i install paranoid then it stucks on boot logo , i tried it several times but none happens,
then i use adb push command ino twrp recovery(3.0.2) to copy cyanogenmod after that i flash it , it fails ,
then i flash cwm recovery then flash is succeded and currently running cm 13 ,
when i installed root checker it said your phone is partially rooted, when i enable root option in developer option then it said root verified.
But when i tried to flash other roms using twrp (3.0.3, 3.0.2) it stucks on boot logo.
Please help me
Exodusche said:
PA I believe is on the old bootloader still. So you would have to downgrade your bootloader by flashing LL stock recovery and 2.x.x OOS firmware. Not worth the hassle if you ask me.
Click to expand...
Click to collapse
lower bootloader can`t flash it fails every time....
Mandeep Singh 07 said:
lower bootloader can`t flash it fails every time....
Click to expand...
Click to collapse
Did you also revert to the old TWRP version 3.0.2? Other then that I'm out of ideas.
Exodusche said:
Did you also revert to the old TWRP version 3.0.2? Other then that I'm out of ideas.
Click to expand...
Click to collapse
At that twrp blu spark 3.0.2 is available and of only that recovery is working lower recoviers cant flash and boot
Mandeep Singh 07 said:
At that twrp blu spark 3.0.2 is available and of only that recovery is working lower recoviers cant flash and boot
Click to expand...
Click to collapse
Right but if your downgrading your bootloader to flash PA you need to use old bootloader TWRP 3.0.2. So that being said easiest way is flash 2.2.3 with blusprk 3.0.2-2 TWRP then immediately after flash TWRP 3.0.2 image. Now re boot back into recovery and flash PA. I prefer flashing 2.2.3 with stock LL recovery less chance of issues. Then just fastboot flash old TWRP 3.0.2 and continue with PA.
Exodusche said:
Right but if your downgrading your bootloader to flash PA you need to use old bootloader TWRP 3.0.2. So that being said easiest way is flash 2.2.3 with blusprk 3.0.2-2 TWRP then immediately after flash TWRP 3.0.2 image. Now re boot back into recovery and flash PA. I prefer flashing 2.2.3 with stock LL recovery less chance of issues. Then just fastboot flash old TWRP 3.0.2 and continue with PA.
Click to expand...
Click to collapse
thanks bro this works fine
Hello everyone, long time lurker here. I have used xda over the course of many years with many different devices, and I am extremely grateful to all of you!
I recently cam across an issue. So with my OnePlus X I had unlocked it, rooted it, installed TWRP and a custom ROM (6.x.x). I had that setup for a while, it worked well, and I enjoyed it. I decided to try to update to a 7.x rom, but that is when I had issues. Trying to install the rom through twrp didn't work, and I couldn't revert back to the old rom either. I tried to use the master unbrick thread to set it back to stock, and it worked. The problem here is the stock rom is very broken, things like the OPX home launcher simply freeze and crash. Trying to usethe guide on the oneplus website to unlock it all again to reinstall TWRP doesn't work. I can unlock it, but installing recovery is where it screws up.
So it says it installs, but then when I try to reboot recovery it has a DTB: not found...manually rebooting to recovery leaves a black screen with the oneplus square logo.
Any ideas how to fix this? I am so lost, but I love this phone!
Fastboot flash old stock recovery from OOS2 wipe data and cache install 2.2.3 followed by 3.1.4 then make sure your flashing latest TWRP 3.0.3 from there site. Now should be able to flash Nougat.
Exodusche said:
Fastboot flash old stock recovery from OOS2 wipe data and cache install 2.2.3 followed by 3.1.4 then make sure your flashing latest TWRP 3.0.3 from there site. Now should be able to flash Nougat.
Click to expand...
Click to collapse
Good work sir! Mind you it probably be far easier for him to just
Code:
fastboot flash recovery 3.0.3.28w/e.img
fastboot boot recovery 3.0.3.28w/e.img
And then just plonk a nougat zip onto his device from the TWRP plugged into is computer?
Archtects said:
Good work sir! Mind you it probably be far easier for him to just
Code:
fastboot flash recovery 3.0.3.28w/e.img
fastboot boot recovery 3.0.3.28w/e.img
And then just plonk a nougat zip onto his device from the TWRP plugged into is computer?
Click to expand...
Click to collapse
No because he needs to upgrade the bootloader first to have a TWRP 3.0.3 that works OK.
Kéno40 said:
No because he needs to upgrade the bootloader first to have a TWRP 3.0.3 that works OK.
Click to expand...
Click to collapse
True true.
Hi peeps
New Pocophone owner here. I got my bootloader unlocked earlier today and now trying to flash the official TWRP 3.3.0.0 recovery from twrp.me, simply following the fastboot instructions on the device guide.
However every time I reboot the device, the recovery always reverts to the stock MIUI recovery?
What am I doing wrong here?
I just got the phone and have upgraded it to MIUI 10.3.6 as well. I am wanting to flash pixel experience onto it.
Do following, instead of flashing your recovery.
Use this method boot and flash Magisk. Reboot back to your system and install Flashify and install your choosen Recovery with it
jonske said:
Hi peeps
New Pocophone owner here. I got my bootloader unlocked earlier today and now trying to flash the official TWRP 3.3.0.0 recovery from twrp.me, simply following the fastboot instructions on the device guide.
However every time I reboot the device, the recovery always reverts to the stock MIUI recovery?
What am I doing wrong here?
I just got the phone and have upgraded it to MIUI 10.3.6 as well. I am wanting to flash pixel experience onto it.
Click to expand...
Click to collapse
in stock rom you need to flash magisk right after flashing twrp else it will get replaced by stock
jonske said:
Hi peeps
New Pocophone owner here. I got my bootloader unlocked earlier today and now trying to flash the official TWRP 3.3.0.0 recovery from twrp.me, simply following the fastboot instructions on the device guide.
However every time I reboot the device, the recovery always reverts to the stock MIUI recovery?
What am I doing wrong here?
I just got the phone and have upgraded it to MIUI 10.3.6 as well. I am wanting to flash pixel experience onto it.
Click to expand...
Click to collapse
What the post above says is correct. However, if you don't want Magisk, after flashing TWRP, reboot into recovery and then into system. You may retain TWRP. However, this doesn't work for everyone.
Hi all, I fixed the issue by completely wiping my phone via TWRP and clean flashing pixel experience ROM. After rebooting on pixel rom TWRP persists.
It appears that MIUI rom has something that keeps reverting it to stock MI-recovery.
If you are on MIUI and flashing TWRP, once the recovery is up for the first time, you need to head on to reboot>recovery again in order to overwrite MIUI stock recovery. So the whole process would be like this;
i) Fastboot flash recovery twrp.img (or whatever the name of the image)
ii) Fastboot boot recovery
iii) Once TWRP is up, Swipe to allow modification and then go to Reboot>Recovery and reboot into TWRP once more. That's it! You have just overwritten the stock recovery and are now on TWRP!! Now you can reboot to system and TWRP will remain on your device. There's no need to flash Magisk etc if you want just TWRP and nothing else.
Rowdyy Ronnie said:
If you are on MIUI and flashing TWRP, once the recovery is up for the first time, you need to head on to reboot>recovery again in order to overwrite MIUI stock recovery. So the whole process would be like this;
i) Fastboot flash recovery twrp.img (or whatever the name of the image)
ii) Fastboot boot recovery
iii) Once TWRP is up, Swipe to allow modification and then go to Reboot>Recovery and reboot into TWRP again. That's it! You have just overwritten the stock recovery and are now on TWRP!! There's no need to flash Magisk etc if you just want TWRP and nothing else.
Click to expand...
Click to collapse
I did those exact steps and it didn't work. It ALWAYS kept getting overwritten.
jonske said:
I did those exact steps and it didn't work. It ALWAYS kept getting overwritten.
Click to expand...
Click to collapse
Did you follow step 3? You can't boot into system right after twrp is up for the first time. You need to reboot into twrp twice before you boot into system. This is what I do whenever I flash twrp and it never failed me yet.
Rowdyy Ronnie said:
Did you follow step 3? You can't boot into system right after twrp is up for the first time. You need to reboot into twrp twice before you boot into system. This is what I do whenever I flash twrp and it never failed me yet.
Click to expand...
Click to collapse
Yes, I even flashed the recovery image from within TWRP and rebooted to recovery again. Still didn't work.
Note this was on the new 10.3.6 stable MIUI release that got rolled out recently. Not sure if it has new detection or anything that rolls it back.
Anyway I have resolved my issue now all is good.
jonske said:
Yes, I even flashed the recovery image from within TWRP and rebooted to recovery again. Still didn't work.
Note this was on the new 10.3.6 stable MIUI release that got rolled out recently. Not sure if it has new detection or anything that rolls it back.
Anyway I have resolved my issue now all is good.
Click to expand...
Click to collapse
How did you fix it?