I've just bought a user Archos 70 IT with a 1Tb disk upgrade. It's started refusing to complete the boot sequence. It flashes up the "Entertainment your way" screen, then goes black a couple of times, then gets stuck on that screen.
I've tried:
- Holding the power button down for 20 seconds to reset it
- Rebooting to recovery mode and selecting the "repair system" option (disk check)
- Rebooting to recovery mode and re-installing the firmware using the gen8 AOS file downloaded from the Archos site - this failed.
Before it died I managed to transfer about 50,000 music tracks to it, but did have the odd problem with USB along the way:
- the unit would only recognise the connection of the USB cable if it was connected before powering it up. If I inserted the USB cable at any time when the tablet was running nothing happened (although sometimes I got an audible tone from the PC, indicating that some sort of connectivity had been made)
- applications (e.g. camera, music) were unable to access the storage device, and suggested that it may be because USB was connected (even though the USB cable was disconnected)
Now I'm stuck unable to reboot it. Can anyone suggest anything?
Well all I can imagine is using the reformat option... but u will loose all data.
Did u have SDE installed before?
If - u also could try installing UD.
So you bought a unit that was opened by some guy, that then installed a 1TB harddrive?
The connection cable is very fragile and if he wasn't 110% accurate this might have come loose or broke.
So check with that guy, open the case again and check the cables.
FrEcP said:
Well all I can imagine is using the reformat option... but u will loose all data.
Did u have SDE installed before?
If - u also could try installing UD.
Click to expand...
Click to collapse
I managed to find an option on the Repair menu (in recovery mode) which re-initialised storage without wiping the HDD. Thankfully this left my music intact and revived the system. Phew....
Thanks for the feedback
Hello everyone,
I just tried to put CM 10.1 (pollux RC3) on my Z, but I think I made a mistake: I accidently used a fastboot command which was meant for the xperia z phone, not the tablet (something like "fastboot flash boot boot.img"). Now I probably crashed my tablet, didn't I?
First a red light was visible, after 10mins I did a vol.up+power button reset. Now the red light is gone and so is my tablet. I can't get it recognized on the computer anymore, I can't start up the device, nothing.
Anyone has an idea what to do or am I just screwed?
*Edit*
Got it working again, see link in last post.
No you're not screwed. Download your corresponding system dump (do a search in this XTZ forum) eg. SGP311 (wifi 16gb), or SGP312(wifi32gb) and so on. Download flashtool (do a search too). FLASH THAT SYSTEM DUMP WITH FLASHTOOL (sorry for caps). HTH.
cool, thanks for the quick reply. I guess I was a bit fast on the first try...cool someone can help me out
downloading the dump and flashtool right now, gonna take a while, slow connection right now.
cheers
Aaalright...*still hoping not to be screwed*
If I plugin the usb cable to the computer, holding the volume button down for flash mode, absolutely nothing happens. I tried windows boxes and linux boxes, neither one of them logs anything happening on the usb ports.
Does anyone have a suggestion what to do? The tablet seems dead...the only thing is a single quick LED blink if I do a reset with power button + vol. up. So far I can't get it to do anything else besides that.
*New situation*
I plugged in the USB cable while holding power+vol up. Now I got a constant red led...
Trying this right now: http://forum.xda-developers.com/showthread.php?p=42003603
Hi all
Today I received my freelander px2. I tried to follow the instructions posted here http://www.pandawillforum.com/showt...-PX2-MTK8389-Quad-Core-(update-Sep-6th-2013)/ to flash the device to the latest clean ROM. I got to the "Download" stage. I clicked the "Download" button and connected my Freelander PX2 with the USB cable.
I was having some issues making Windows 7 actually pick up the "MTK" device and load the correct driver. So I was playing around with the drivers and disconnecting and reconnecting the Freelander PX2 (Whilst leaving the Flash tool on DOWNLOAD mode, which was waiting for me to connect the Freelander PX2)
I must have reconnected it several times in the process of trying to make Windows 7 recognise the device. When I looked at the flash tool I noticed it had got to around 57% with the progress bar and stopped. I can only assume I managed to get the MTK drivers installed correctly at some point but tablet didn't really tell me new software was being uploaded to it. So basically I didn't know the flash tool was sending the new software to the tablet when I must have disconnected it during the process.
I can only assume I've interrupted the NAND flash process? When I try to reconnect the tablet now, it says "USB Device Not Recognized". There doesn't seem to be much support anywhere on the internet for this specific device or issue.
I've tried holding the power button for 30 seconds.. nothing happens
I've tried holding the power button plus volume up button for 30 seconds.. nothing happens
There's also no USB disconnect sound when I hold the power button down? Surely a hard reset should trigger a USB disconnect sound in Windows.
What are my options at this stage? Is it completely dead?
EDIT: Ok, this was a bit strange. I left it yesterday morning and declared it dead. Today I woke up, switched my computer on and plugged it in using a different USB cable and the driver was automatically installed as "MTK preloader". I didn't try to switch the device on yet though, as I wasn't sure if it being recognized was by chance. I didn't ask questions. I just immediately started up the flash tool, hit "download" and re-plugged the USB cable. This time the software finished upload with 100% and a green circle. Then it automatically disconnected from the computer. I hit the power button and it needed some time to charge again (maybe it drained itself last time). A few minutes later the OS booted completely fine. I don't know which one of those things made it worked, the new USB cable or leaving it to discharge for a day.. I just don't know. I'm not taking any chances though, the USB cable is being binned.
Have you flashed the CWM recovery for the px2 yet?
What do you think about the new firmware? I think its alot snappier than the old one. The CWM recovery works a treat (but you have no usb cable lol ) so you cant flash it. If you do want to put the recovery on it, let me know i can help. Cheers
PX2 Bricked
Hi,
Glad you got yours working :good:
I have exactly the same problem and now mine is not reconised :crying:
How long does the flashing actually take ?
When I connected it again this morning it it reconised it and the flash toll started to work.
The green bar and red bars both went to 100% then nothing after 5 mons so I unplugged it.
Now its bricked again :crying:
Any advice guys please ?
Reset
Hi mate sorry to here of your problems. Try pressing the little button between the sim slots, if that doesnt work, press volume + and then power button and keep pressed until it starts. When you flashed it did you get the green circle at the end?
If you get it recognized again do this: ENSURE YOU HAVE FULL BATTERY AND DO NOT INTERUPT THE FLASHING
1/ Start tablet and connect usb data cable, ensure it is connected as Media device (MTP).
2/ Unpack PX2_PC_24-10-13 update to a folder of your choice.
3/ Start Flash tool and click scatter loading on the right, and go to your unpacked folder you made earlier and select MT6589_Android_scatter_emmc check ALL boxes at the bottom are selected.
4/ Now click on downlod button, then switch off tablet. It will either ask to load drivers or start the flashing process.Wait until you see the green circle.
5/ Restart tablet. ENJOY
If you want to put clockwork recovery on it do the following:
1/ Download Freelander_PX2_130717_CWM_recovery.img in post #162 at pandawill put it in a folder and copy MT6589_Android_scatter_emmc from the folder above to the same folder.
2/ Start tablet and connect usb data cable, ensure it is connected as Media device (MTP).
3/ Start Flash tool and click scatter loading on the right, and go to your Freelander_PX2_130717_CWM_recovery.img folder you made earlier and select MT6589_Android_scatter_emmc only recovery option should be checked. Dont worry about the red writing.
4/ Click download and switch off tablet, dont worry about the warning just go ahead anyway, it will only take a couple of seconds and you should see the green circle again.
5/ To check it worked press vol+ and power button to get to recovery ( should be blue text ) if it is congrats you have clockwork recovery.
6/ Enjoy your tablet
Hi,
Thanks for your help but I fear it may be terminal,as when I plug the usb in now I get nothing.
gonna try on a different computor later.
If that fails I fear my PX2 will be leaving via the upstairs window
---------- Post added at 04:43 PM ---------- Previous post was at 03:57 PM ----------
Well it wont even charge now !
I wonder if this could mean a hardware problem or a software not sure ?
Any Ideas guys ?
:crying::crying::crying::crying::crying:
PX2 revival
Hi bazza500, try pressing the reset button between the sim slots it has saved me a couple of times when i thought i had bricked mine.
If you go to the pandawill forum under MTK tablets you will find a thread there dealing with an updated by users flashable firmware with cwm recovery.
Then later if you get it up and running there is a solution to extend the internal memory from 1Gb to 2Gb which reduces the storage by 1Gb. Hope you get it running buddy. Cheers
A few tips
Windows 7 has a glitch where by if the path has Chinese characters in it the flash tool with crash/error. Extract everything to your desktop and delete the chinese characters in the folder names.
Also there's a driver error in Windows 7. Make sure you use the driver install tool to install the MTK drivers. Also make sure the driver is installed and the tablet is recognised before you run the flash tool. That's the error I made, I tried to get the drivers installed whilst running the flash tool and the firmware started flashing when I hadn't realized.
Unlike Samsung and Apple, most Chinese devices don't give you a fancy progress bar on the device. There's almost no feedback the tablet or phone being flashed in most cases.
Thanks for the help guys................
Got my replacement today but have hooked it up to updrade and there was about 3 x colours went to 100% on progress bar now nothing for 15 mins !
Is this normal ?
Well a massive fail again.
Gonna send thos one back and get my money back.
Always a bad idea to by cheap o suppose u het what u pay for.
Sent from my GT-N7000 using xda app-developers app
Ok been awhile but I now have a new one and managed to upgrade the rom.
Only one problem I keep losing phone signal ?
Any ideas?
GS701B [ATM7013 CPU] Brick Repair
In this thread i am going to show you how to unbrick your gs7013b tablet without recovery mode.
Please be aware that i have spent a lot of time researching and sourcing the resources to be able to do this and it may or may not work for other MIPS tablets....
firstly you need to set up your computer environment (drivers etc)
Downloads
Actions Product Tool 1.02_02 (Developer Edition)
Firmware Files
When you have finished download the above files extract the actions developer tool to a folder on your desktop for easy access and do the same for the firmware files.
Now we need to get your tablet into ADFU Mode (ADFU = Actions Device Flash Utility)
FOLLOW THE INSTRUCTIONS CAREFULLY OR YOU WILL HAVE NICE LOOKING SQUARE FRIZBY
firstly open up your tablet by popping off the rear panel.
when you have opened the tablet up you should have something like the below picture.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now to get the tablet into ADFU Mode connect your usb cable to tablet and computer and remove any memory card you may have inserted.
now you need to find a tiny flat screwdriver or knife or something similar and we need to short pins 7-8 or 8-9 on the tablets nand chip to force it into ADFU Mode while shorting these pins keep pressing power button until computer recognizes it.
see picture below.
NOTE: i have been informed by some users that the nand chip on their devices is actually soldered on inverted to find pin 1 simply look at the chip and in one corner there will be a little circle which is sort of sunk into the chip this means that pin 1 is on the same corner as the little circle..
when you get the tablet into ADFU Mode your computer will make a sound as if you have just plugged in a usb device. Your computer will now ask for the adfu usb driver which you should have in the Actions Tablet Product Tool 1.02_02(Developer Edition)\Tablet Product Tool(Developer Edition) 1.02\Driver\ folder on the desktop which you downloaded earlier. point windows to he driver and you should now have the device installed...
now goto the Actions Tablet Product Tool 1.02_02(Developer Edition)\Tablet Product Tool(Developer Edition) 1.02\Product folder and run the mainapp.exe
the tool will open and then ask for a firmware file choose the icecream_gl5201_q8_rgb.fw which was in the firmware files zip you downloaded earlier
Now when the tool has read it you need to click the button as in the picture below.
Now on the right of the tool there are a few check boxes etc LEAVE EVERYTHING ALONE apart from the 2 options i explain below
click the image button for FAT_MISC Partition and choose the ACTA.IMG you downloaded earlier in the firmware files.zip
no click the image button for System Partition and choose the ACTB.IMG you downloaded earlier in the firmware files.zip
Now click the big green button as in picture below.
when flashing is done reboot tablet if it doesnt reboot automatically
BOOM working tablet... you should now be able to use your tablet with what you just flashed or you can try a different rom using stock recovery
CREDITS
massive thanks to
Edo2013 (xda forums) for helping me with software and firmware sourcing and flashing.
EDIT: IF YOUR TABLET WILL NO LONGER GO INTO ADFU MODE AFTER BAD FLASH AND SEEMS TO BE TOTALLY DEAD USE THIS METHOD TO GET IT WORKING AGAIN
POST #15 http://forum.xda-developers.com/showpost.php?p=50938861&postcount=15
no work for me
Greetings, I did not work after installing the TF-20121031-Q8-0329camera.zip no longer lights follow your tutorial step by step, and if I go into DFU mode, but it marks 98 error (as well try to install the CEMA10S24 . indicates rar Error 8 but I do not know what to do is the tablet of my daughter. beginning for all problems has stopped the process in various applications.
I hope you can guide me
comgunner said:
Greetings, I did not work after installing the TF-20121031-Q8-0329camera.zip no longer lights follow your tutorial step by step, and if I go into DFU mode, but it marks 98 error (as well try to install the CEMA10S24 . indicates rar Error 8 but I do not know what to do is the tablet of my daughter. beginning for all problems has stopped the process in various applications.
I hope you can guide me
Click to expand...
Click to collapse
hi at which point in the above process do you get the errors?? i cant help you without a bit more information.. if the errors are during flashing then please try a different usb cable and make sure your in adfu mode by checking device manager.. also if you are using windows vista/7/8 it would be a good idea to run everything as administrator or turn uac off completely. make sure your computer is setup correctly and fully updated with the latest .net framework etc...
Q8 GS701B [ATM7013 CPU] hang on android logo
Very helpfull tutorial. Thank you.
But I've got a little bit different problem with my tablet. When I turning on my tablet during booting it is hang on android logo. I've tried all firmware from ele-china and tried also icecream_gl5201_q8_rgb.fw and CEMA10S24 but no one works for me.
When I use your method upgrade is successfull but it is still the same problem with hang on android logo.
I've tried also check box FLASH READ CHECK see attached screen shot. After that its appear checksum error and error 81.
Do you have any idea what can help wit this issue?
My gs701b tablet is not bricked but its touch screen does not work. I tried to download iccream rom you put here to my tablet and I tried another
Rom but touch screen does not work? Is that hardware problem or software. The problem occurred after upgrading to rom upgrade.fast.fw.
Thanks
you will have a hard time getting it to work what you need to try to do is pull the ts drivers from your previous working firmware and then insmod them to this one although doing this is not an easy process it took me week to get my tablet working again.. your ts dont work becuase it uses a different driver for touchscreen which is not the same as mine you need to find someone with the same tablet as yours and get them to give you a dump of there acta and actb partitions....
i currently cant give much support as i got rid of my gs701b tablets as it is a mips tablet and the support for mips is almost non existant becuse of its incompatibilty with almost all apps on the market and the lack of firmware for these tabs are almost also non existant..
I have flashed some wrong firmware that was supposed to be for tablet with a home button. Now it does not power on. Screen does not light up. When I plug it in with usb cable I hear windows notification sound. Then I longpress power button and I hear windows notification sound that indicates shutting off connected device. Doing so also makes it to disappear from device manager. As soon as I release the power button I hear a positive notification sound again and it reappears in device manager once more. So I am stuck at this point. I managed to install unsigned Actions USB 2.0 HS driver, this is how it appears on device manager. I have tried to power it on with cable connected while shorting nand pins but same thing happens.
* UPDATE * So I tried Again. Screen lighted up and is white. I opened tablet product tools. Added firmware and two images. Pressed the green large button. Process have started and got stuck at DOWNLOADING ADFUS ... 20% clock is ticking at 19 minutes now and the progress bar wont move.
* UPDATE * After 143 min and 30 secs i checked on the progress of downloading adfus. It was still 20% but I noticed that a small question window popped up "upgrade firmware" pressed OK. Progress bar went to 95% with title UNKNOWN ERROR. The clock has stopped.
* UPDATE * I have tried again. It takes about 60 minutes until I get the UNKNOWN ERROR an the flashing process stops. Maybe Im not getting into adfu mode? The tool program thing the tablet is ready for flashing as soon as I plug in usb cable or hold power button for 10 secs to shut it off and then release it. The screen goes white after download adfus reaches 20% and it takes about 5 seconds.
* UPDATE * Now I understand that small pop up window on tools program actually says "upload partition error".
Varnuunas said:
I have flashed some wrong firmware that was supposed to be for tablet with a home button. Now it does not power on. Screen does not light up. When I plug it in with usb cable I hear windows notification sound. Then I longpress power button and I hear windows notification sound that indicates shutting off connected device. Doing so also makes it to disappear from device manager. As soon as I release the power button I hear a positive notification sound again and it reappears in device manager once more. So I am stuck at this point. I managed to install unsigned Actions USB 2.0 HS driver, this is how it appears on device manager. I have tried to power it on with cable connected while shorting nand pins but same thing happens.
* UPDATE * So I tried Again. Screen lighted up and is white. I opened tablet product tools. Added firmware and two images. Pressed the green large button. Process have started and got stuck at DOWNLOADING ADFUS ... 20% clock is ticking at 19 minutes now and the progress bar wont move.
* UPDATE * After 143 min and 30 secs i checked on the progress of downloading adfus. It was still 20% but I noticed that a small question window popped up "upgrade firmware" pressed OK. Progress bar went to 95% with title UNKNOWN ERROR. The clock has stopped.
* UPDATE * I have tried again. It takes about 60 minutes until I get the UNKNOWN ERROR an the flashing process stops. Maybe Im not getting into adfu mode? The tool program thing the tablet is ready for flashing as soon as I plug in usb cable or hold power button for 10 secs to shut it off and then release it. The screen goes white after download adfus reaches 20% and it takes about 5 seconds.
* UPDATE * Now I understand that small pop up window on tools program actually says "upload partition error".
Click to expand...
Click to collapse
i have never had this problem all i can suggest is trying to use a different usb cable or maybe even a different computer... i had something simular to this before a while ago an i took it to friends house and used his laptop and it went through the process perfectly..
Would like to say thanks handy trick work wonders, Aoson M723, (Actions ATM7029) was looking at upgrading, flashed incorrectly. Only issue now OTG is still not working and Gsensor is not working now
Just happy to have the tablet working again.
One minor issue, when I plug in the USB, the tablet shows the boot up image, little odd, what could the possible cause be for that ? I can only think of the actions USB driver causing the trouble how do I go about removing the driver ?
Dear sir, any chance that you have tried this one an Ainol Novo 7 Venus Lite. Mine is deep bricked and I can't even get it to be recognized on my Laptop, by holding Vol+ and Power. I got CXZ ADB drivers installed and the Pad tool Ver. 1.05, but nothing happens and I fear I need to open it up and shorten pin 5 and 6 as mentioned by fuser-invent here;
http://www.slatedroid.com/topic/414...-amlogic-aml8726-mx-series-tablet-v20/page-30
His guide is not for the venus but for the Crystal.
Can you help me out here?
With kind regards
JBJ
insomniacno1 said:
Dear sir, any chance that you have tried this one an Ainol Novo 7 Venus Lite. Mine is deep bricked and I can't even get it to be recognized on my Laptop, by holding Vol+ and Power. I got CXZ ADB drivers installed and the Pad tool Ver. 1.05, but nothing happens and I fear I need to open it up and shorten pin 5 and 6 as mentioned by fuser-invent here;
http://www.slatedroid.com/topic/414...-amlogic-aml8726-mx-series-tablet-v20/page-30
His guide is not for the venus but for the Crystal.
Can you help me out here?
With kind regards
JBJ
Click to expand...
Click to collapse
i know this might not be the right place for this but maybe some one can take me to the right place i have a Proscan plt4311 and useing this same way i can restore my firmware so my question is this my tablet does not have gapps on it and i want to put it on there i have found a way to root it but now is the problem i just cant find anyplace that has a way to flash gapps to it if i could install the files useing root explore how can i do that ect thanks
message: "Encryption unsuccessful"
Hi!
Everything went perfect with update with no errors. But after the android logo, when system is starting, I see message: "Encryption unsuccessful" and than folowing text: "Encryption was interrupted and can't complete. As a result, the data on your tablet is no longer accessible. To resume using your tablet, you must perform a factory reset. When you set up your tablet after the reset, you'll have an opportunity to restore any data that was backed up to your Google Account". There is a button "Reset tablet". After the reset, tablet starts I reach again the message above.
Any ideas what's going wrong? After update tablet did not starts alone, but I manualy press power button and it starts. Before power on, I see that update proces in MainApp.exe was finished.
And also I have no recovery options by pressing Volume UP + Power buttons.
And finaly: can I put other firmware to upload using that application, and should I use acta.img and actb.img whith any other firmware?
Thanks in advance!
Hey, same thing
bastunbastun said:
Hi!
Everything went perfect with update with no errors. But after the android logo, when system is starting, I see message: "Encryption unsuccessful" and than folowing text: "Encryption was interrupted and can't complete. As a result, the data on your tablet is no longer accessible. To resume using your tablet, you must perform a factory reset. When you set up your tablet after the reset, you'll have an opportunity to restore any data that was backed up to your Google Account". There is a button "Reset tablet". After the reset, tablet starts I reach again the message above.
Any ideas what's going wrong? After update tablet did not starts alone, but I manualy press power button and it starts. Before power on, I see that update proces in MainApp.exe was finished.
And also I have no recovery options by pressing Volume UP + Power buttons.
And finaly: can I put other firmware to upload using that application, and should I use acta.img and actb.img whith any other firmware?
Thanks in advance!
Click to expand...
Click to collapse
I have been working on this tab for days, and I have the exact problem as this dude mentioned. I can't get into ADFU when I short the pins anymore, and i've been trying for over an hour, which means I can't flash again. No recovery options, no way to access USB debugging on the tablet, I can't figure this thing out. I think the cause might be manually restarting the device once it appears to be done but it really is not. Perhaps our impatience got the best of us.
Trio Stealth Lite 4.3 GS701b without home button. Please, please help us. Willing to donate a handsome amount, and i'm completely serious.
WeActOnImpulse said:
I have been working on this tab for days, and I have the exact problem as this dude mentioned. I can't get into ADFU when I short the pins anymore, and i've been trying for over an hour, which means I can't flash again. No recovery options, no way to access USB debugging on the tablet, I can't figure this thing out. I think the cause might be manually restarting the device once it appears to be done but it really is not. Perhaps our impatience got the best of us.
Trio Stealth Lite 4.3 GS701b without home button. Please, please help us. Willing to donate a handsome amount, and i'm completely serious.
Click to expand...
Click to collapse
hi sorry for my ignorance i have been away on holiday...
the picture in the OP of the nand chip is a little misguiding.. i am guessing you have both tried pins 7-8 and 8-9 if so an its not working try the pins on the other side of the nand chip as some model version differ from others i have had 3 of these and had the same issue although i solved the problem by getting a thin sharp blade eg, craft knife blade and i pressed it onto all the pins on one side of the chip and this worked for me although be aware of the fact that you could possibly permanantly damage the nand by doing this... (but i have not ever damaged a nand chip or tablet doing this and this is now my preferred method..
Also try pins 5 - 6
and when shorting the pins also try to push the vol- or vol+ and the power button
there is no other way to get the tablet into adfu mode the only way is by shorting the nad and while you have the pins shorted turn the tablet on..
if you have any questions or need more info let me know..
Inside 4ndroid said:
hi sorry for my ignorance i have been away on holiday...
the picture in the OP of the nand chip is a little misguiding.. i am guessing you have both tried pins 7-8 and 8-9 if so an its not working try the pins on the other side of the nand chip as some model version differ from others i have had 3 of these and had the same issue although i solved the problem by getting a thin sharp blade eg, craft knife blade and i pressed it onto all the pins on one side of the chip and this worked for me although be aware of the fact that you could possibly permanantly damage the nand by doing this... (but i have not ever damaged a nand chip or tablet doing this and this is now my preferred method..
Also try pins 5 - 6
and when shorting the pins also try to push the vol- or vol+ and the power button
there is no other way to get the tablet into adfu mode the only way is by shorting the nad and while you have the pins shorted turn the tablet on..
if you have any questions or need more info let me know..
Click to expand...
Click to collapse
That was genius because it worked. I just pressed a cream cheese knife against the opposite side and it booted into ADFU mode, first try. Thank you. here's some images, maybe you can include this in OP for future reference if the same thing happens, because after the flash it switches which pins need to be pressed.
Problem is, though, that I still get the "encryption unsuccessful" message after a successful flash. I can't access USB debugging, a factory reset doesn't get rid of the message, and I can't seem to find the recovery menu to flash a different ROM. Perhaps you know how to get into recovery/download mode? Or is that ADFU and I should find a different ROM to flash with that program? Here's a video if you want to see exactly what's happening. (It has my beautiful voice, lol.)
Thanks again.
At my tablet the flasher is getting stucked at 20% .
Is there any solution ?
Thanks !
Glad it worked for you..
as for the encryption problem i personally have never come across this and i would defo suggest trying a different firmware or maybe even a different version of the flash tool..
getting stuck at 20% is because you are trying to flash incompatible firmware..
Thanks for the reply but where to download correct flash for my tablet ?
ATM7013 , GS701b without home button .
Thanks !
usernome said:
Thanks for the reply but where to download correct flash for my tablet ?
ATM7013 , GS701b without home button .
Thanks !
Click to expand...
Click to collapse
Good question... The answer we all would like to Know but you will find some here these are all that i know of at the moment
http://www.ele-china.com/soft/tablet/Atm/Q8/
let me know how it goes..
an if the link above contains what you need please dont forget to hit the thanks button
My tablet is bricked . I cannot enter recovery menu and flash from sd-card .
That firmware aren't recognized by the flasher .
Hi people!
I have this headache with this tvbox since it got stuck at android logo (idk what my uncle did to this device). I can't enter recovery mode, despite I tried with all methods like hard reset button, usb flashing with phoenix suit, or microsd card flashing, it only stays at red light. It even doesn't get recognized by windows (It says "unknonwn device" on device manager).
I tried everything, installing adb legacy drivers, tried with both usb ports, holding the reset button for a looong time and nothing.
So please, I need help of this great community!
Did you find any solution for this mate?
take a wooden toothpick, press the button through the av output one second after power on, after 5 seconds release the button and wait for the device to be cleaned. after that the box will work