Hi Folks,
After running droid RAZR root unable to load OS the phone get stuck in this screen.
"AP fastboot Flash Mode (S)(Flash Failure)
0A.6C
To return to normal mode - first press power key to power down
Devise is locked , status code : 0
I pressed the power key + power to power down but its does not turn the RAZR normal mode.
Plz help.
Hope this guide helps.
http://forum.xda-developers.com/showthread.php?t=1539192
Hold both power key and the volume +,- key ,wait for device to turn off the screen and still hold the volume key without power key.and then selected the BP tools.Good luck.
Sent from my XT910 using xda premium
I got a XT912 with a screen that stays black(don't know why, it looks fine). What i am trying to do, is to get into the fastboot mode without seeing anything so i can flash a stock rom via pc. Whatever combinations i try i only get it to reboot(it keeps saying "droooiiiidd"). I googled alot and i can't find a solution for this.
The reason why i want to flash a new rom is because i want to try if i can fix this screen issue and because the screen is locked and i can't get past that and use the phone(via otg and hdmi out).
How do i shut the phone down only using the keys(without restarting) and how do i start from a powered down mode into fastboot(step by step guide would be helpful).
Ensure phone is completely powered off (also, fully charged). Vol down + Power (vol down first). Release power button after 3-5 seconds, and then release vol down. You are now in fastboot. Connect usb, and your computer should identify the phone.
LuckiestNut419 said:
Ensure phone is completely powered off (also, fully charged). Vol down + Power (vol down first). Release power button after 3-5 seconds, and then release vol down. You are now in fastboot. Connect usb, and your computer should identify the phone.
Click to expand...
Click to collapse
What about selecting fastboot first? Isn't there some kind of menu i get into after doing that(at least i know there should be one)? Where i have to scroll down and select fastboot.
Holding vol up and vol down will bring you to the boot menu. Vol down is directly to fastboot mode.
Sent from my XT912
LuckiestNut419 said:
Holding vol up and vol down will bring you to the boot menu. Vol down is directly to fastboot mode.
Sent from my XT912
Click to expand...
Click to collapse
Can i somehow shut it down with the keys? I don't know why, but whatever i try it keeps rebooting only.
Press and hold both vol buttons and the power button for six to ten seconds. Then release all three. That is a manual reboot. A working screen will briefly flash. If you try to boot to the main boot menu, with vol +/-, and power, AP Fastboot is the third option. Press vol down twice to highlight ap fastboot, vol up once to select it. This also takes you to AP Fastboot mode, as opposed to the vol down and power, which is direct.
Sent from my XT912
LuckiestNut419 said:
Press and hold both vol buttons and the power button for six to ten seconds. Then release all three. That is a manual reboot. A working screen will briefly flash. If you try to boot to the main boot menu, with vol +/-, and power, AP Fastboot is the third option. Press vol down twice to highlight ap fastboot, vol up once to select it. This also takes you to AP Fastboot mode, as opposed to the vol down and power, which is direct.
Sent from my XT912
Click to expand...
Click to collapse
Thats what i tried just now, i pressed vol+/- and power to reboot. Soon after i pressed again vol+/- and power and waited for like 10 sec, then i pressed vol - 3 times and then vol + and all he did was reboot again damn. Is my timing wrong? 3 times down is wrong i guess if i start from position 1. Just as a reminder i can't see anything.
Volume down twice to highlight AP fastboot, up once to select. Also, you want the phone to be completely off to boot into fastboot mode. There is no way to REboot into the boot menu
Sent from my XT912
LuckiestNut419 said:
Volume down twice to highlight AP fastboot, up once to select. Also, you want the phone to be completely off to boot into fastboot mode. There is no way to REboot into the boot menu
Sent from my XT912
Click to expand...
Click to collapse
What i did now is open the back, disconnect the battery and connect it again, use vol down button + power button for ten sec and then plug it into the computer. Nothing happens, atleast not on the computer, the phone shows a white light in the top left corner. It stays on even if i disconnect the cable.
Holding for that long can cause a reboot. Try holding the vol down and power for like... three seconds, after reconnecting the battery. Also, are you using an OEM motorola cable? And, have you ever used RSDlite? Have you prepared for flashing with the appropriate fastboot sbf files? Once the computer recognizes the phone, you'll want to have the motorola drivers installed, RSDlite ready, and the right sbf file ready.\
EDIT
Even if you do access the fastboot menu, if the phone believes the battery is too low, it will not allow the pc and phone to connect. The screen should say:
AP Fastboot Flash Mode (S)
0A.77
eMMC Info: Size 16G
To return to normal mode- first press power key to power down
Device is LOCKED. Status code: 0
Battery OK
OK to Program
Connect USB
Data Cable
I realize that your screen isn't displaying anything, but this menu is what will restrict you from flashing if the battery is low. Instead of Battery OK, it will say Low Battery
LuckiestNut419 said:
Holding for that long can cause a reboot. Try holding the vol down and power for like... three seconds, after reconnecting the battery. Also, are you using an OEM motorola cable? And, have you ever used RSDlite? Have you prepared for flashing with the appropriate fastboot sbf files? Once the computer recognizes the phone, you'll want to have the motorola drivers installed, RSDlite ready, and the right sbf file ready.\
EDIT
Even if you do access the fastboot menu, if the phone believes the battery is too low, it will not allow the pc and phone to connect. The screen should say:
AP Fastboot Flash Mode (S)
0A.77
eMMC Info: Size 16G
To return to normal mode- first press power key to power down
Device is LOCKED. Status code: 0
Battery OK
OK to Program
Connect USB
Data Cable
I realize that your screen isn't displaying anything, but this menu is what will restrict you from flashing if the battery is low. Instead of Battery OK, it will say Low Battery
Click to expand...
Click to collapse
I know how to use rsdlite, because i flashed my xt910 with it. The battery could be a problem. I have it fully charged and will try it again now, but if that doesn't work i propably need a factory cable. I think i made it into the fastboot mode in previous tries but got stuck because of the battery status.
Edit: Reconnecting the battery and getting into fastboot mode seems to work, but connecting the cable gives me the white light and nothing else works.
So your computer is still not recognizing the phone, even when it seems to be in fastboot?
Sent from my XT912
LuckiestNut419 said:
So your computer is still not recognizing the phone, even when it seems to be in fastboot?
Sent from my XT912
Click to expand...
Click to collapse
Yep, no reaction from the os and nothing listed in adb devices or fastboot devices.
Assuming the battery power is adequate, the next and only solution is the proper data cable (OEM).
If the battery is low, you'll need to either use a TBH factory data cable, or the workaround of hard wiring a stripped usb cable screwed to the battery terminals on the phone. Once the phone identifies a good power source, it will allow a pc connection.
Sent from my XT912
EDIT
BP SBF Flash is the fourth option down, out of seven total, I believe. If you can boot to the main boot menu, and click vol down 3 times, you'll select this option. As I recall, I was able to confirm my phone, usb cable, and pc were all communicating. My *pc identified an unknown device being connected, even with a nearly dead battery. Then I knew I just needed a power supply. I'm not sure what this option is for, but it told me what I needed to know.
LuckiestNut419 said:
Assuming the battery power is adequate, the next and only solution is the proper data cable (OEM).
If the battery is low, you'll need to either use a TBH factory data cable, or the workaround of hard wiring a stripped usb cable screwed to the battery terminals on the phone. Once the phone identifies a good power source, it will allow a pc connection.
Sent from my XT912
EDIT
BP SBF Flash is the fourth option down, out of seven total, I believe. If you can boot to the main boot menu, and click vol down 3 times, you'll select this option. As I recall, I was able to confirm my phone, usb cable, and pc were all communicating. My phone identified an unknown device being connected, even with a nearly dead battery. Then I knew I just needed a power supply. I'm not sure what this option is for, but it told me what I needed to know.
Click to expand...
Click to collapse
Ok i will try that until i get one of these cables or adapters.
Is it possible to use adb via recovery or do i need a custom recovery for that? I am not sure if i need to unlock the bootloader via motorola( have to use fastboot for unlock), that would as far as i know reset the stock rom(if i need a custom rom).
Hello friends!!
I have a little problem, i was trying to root my Razr but i couldn, by the way the process brick the boot so now when i press the power button, appears a black screen and said:
AP FastBoot Flash Mode (S) (Flash Failure)
0A.77
eMMc.info size 16g
To return to normal mode-first press power key to power dwn.
Device is LOCKED. Status Code:0
Battery OK
OK to program
Transfer Mode
USB Conected
i can make the phone boot if i press vol +, vol -, and power and i choose normal boot, then start, but if i turn off the cellphone and only push power button always shows the black screen with the message.
when i tried to flash it with RSD Lite always get an error. i live the picture to see if some one can help me!!
Don Mike said:
Hello friends!!
I have a little problem, i was trying to root my Razr but i couldn, by the way the process brick the boot so now when i press the power button, appears a black screen and said:
AP FastBoot Flash Mode (S) (Flash Failure)
0A.77
eMMc.info size 16g
To return to normal mode-first press power key to power dwn.
Device is LOCKED. Status Code:0
Battery OK
OK to program
Transfer Mode
USB Conected
i can make the phone boot if i press vol +, vol -, and power and i choose normal boot, then start, but if i turn off the cellphone and only push power button always shows the black screen with the message.
when i tried to flash it with RSD Lite always get an error. i live the picture to see if some one can help me!!
Click to expand...
Click to collapse
Have you tried the Droid Razr Utility?
No friend!! Do you have the link to download it? its not the same as XT912 true?
I think I saw a similar thread before, and the problem with RSD were the drivers; however I'm not sure about it. Try to dig a bit in these forums, I'm sure you'll find the answer.
Edit, these might help:
http://forum.xda-developers.com/showthread.php?t=1796712
http://forum.xda-developers.com/showthread.php?t=1815242
http://forum.xda-developers.com/showthread.php?t=1634223&page=2
Im new here, earning my 10 comments atm thanks
Hello,
My xt916 bricked for no reason. It is not rooted. Do not respond to any commands such power, power + volume down, power + volume up. The only sign of life is when connected to charger or USB the back home and menu buttons on the bottom light in white.
Searching for solutions I tried to flash stock again with MTK-RSD Lite ver 6.1.6. Used rom XT916_2_26D_2014_A02_MP.mzf
The device appears as connected and enters download mode. The process completes and it shows PASS at the end.
However no sign of life afterwards. Same as before.
Tried to enter recovery mode or fastboot via ADB but when I type adb devices nothing is shown.
beniciof98 said:
Hello,
My xt916 bricked for no reason. It is not rooted. Do not respond to any commands such power, power + volume down, power + volume up. The only sign of life is when connected to charger or USB the back home and menu buttons on the bottom light in white.
Searching for solutions I tried to flash stock again with MTK-RSD Lite ver 6.1.6. Used rom XT916_2_26D_2014_A02_MP.mzf
The device appears as connected and enters download mode. The process completes and it shows PASS at the end.
However no sign of life afterwards. Same as before.
Tried to enter recovery mode or fastboot via ADB but when I type adb devices nothing is shown.
Click to expand...
Click to collapse
Follow these instructions to perform a factory reset on the Razr and Razr D1 D3:
*
With the phone off, remove your SIM card, then press the power button for 1 second while pressing the volume button up
Select the recovery mode by pressing the volume key down until the factory mode (Factory) and press the power button
Wait for the Android appears and press the volume up
Scroll to wipe data / factory reset (wipe data / Factory reset) and press the power button
Scroll to the option Yes - Delete all data (Yes, delete all user data) and press the power button
Select Reboot System Now (Reboot system now) by pressing the power button
Remind client will lose all data stored in the internal memory.
https://motorola-global-es-latam.cu.../prod_answer_detail/a_id/93717/p/30,6720,8632
Sent from my KFFOWI using Tapatalk
sd_shadow said:
Follow these instructions to perform a factory reset on the Razr and Razr D1 D3:
*
With the phone off, remove your SIM card, then press the power button for 1 second while pressing the volume button up
Select the recovery mode by pressing the volume key down until the factory mode (Factory) and press the power button
Wait for the Android appears and press the volume up
Scroll to wipe data / factory reset (wipe data / Factory reset) and press the power button
Scroll to the option Yes - Delete all data (Yes, delete all user data) and press the power button
Select Reboot System Now (Reboot system now) by pressing the power button
Remind client will lose all data stored in the internal memory.
*** edit link removed *****
Sent from my KFFOWI using Tapatalk
Click to expand...
Click to collapse
Thanks for the tip. Already tried this. The phone only lights up when connected by USB or charger. Whether is connected or disconnected (with battery only) it does not respond at all to any key combinations.
The only noticeable thing it is when connected by USB with RSD Lite software when I try power volume down the phone enters download mode and I can flash a rom.
beniciof98 said:
Thanks for the tip. Already tried this. The phone only lights up when connected by USB or charger. Whether is connected or disconnected (with battery only) it does not respond at all to any key combinations.
The only noticeable thing it is when connected by USB with RSD Lite software when I try power volume down the phone enters download mode and I can flash a rom.
Click to expand...
Click to collapse
try house of moto
Moto Drivers, RSD Lite, and other Unbricking Tools
Sent from my KFFOWI using XDA Labs
thanks. gonna give it a shot. I figure out it would not be a very simple solution since I've tried many other solutions until get here.
Hi,
How can flash again ?
Since I couldn't enter Safestrap.
Please advice.
Thanks！
Power off, Hold volume buttons, Power on, release buttons at
Boot Mode Selection Menu> Scroll down with volume down button, to BP Tools, Select with Volume UP button, should boot directly to SafeStrap (if it's still there).
Hi,
I was tried but failure too....
I am trying to flash xml with RSD Lite, but I got "battery low" in fastboot mode.
Please advice.
Thanks
cannot flash with low battery, there is a hardware fail safe
you will need a fastboot cable see
Moto Drivers, Firmware, RSD Lite, and other Unbricking Tools
I have donwloaded, but I still need a fastboot cable ?
And it can charge-up my XT910 ?
Thanks
Yes, you need a fastboot cable
it will bypass battery and power phone directly from USB
By cut the off the B plug (the one that plugs into the device) and strip away the shielding ......
Thanks
Otherwise, I have to open XT910 case for cable connection ?