Related
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Remove Kies and reinstall see if it picks the phone up and installs the drivers .
jje
OperationIvy85 said:
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Click to expand...
Click to collapse
That kernel is for the Epic touch 4g is that your phone or do you have the international version? If you flashed the wrong kernel it could cause problems.
Yes it's an Epic touch 4g from sprint.
EDIT: Uninstalled Kies, reinstalled Kies, restarted computer, still no kind of recognition of my phone in any state (powered off, at "Firmware upgrade encountered" screen it boots into, or in download mode). Starting to get nervous, I used to at least hear a sound when plugging my phone into my comp. It is like there is nothing on the other end of the USB cable.
More things I have tried:
-All of the above steps on a different computer
-Sweet talking it
-Talking dirty to it
Am I brick'd? I figure not, since I can at least get into download mode. Not sure what else I can do though. I'd go see what the Sprint store can do for me, but on the download mode screen it lists my custom binary download count as 5, I understand they will see that and tell me I'm out of luck?
OperationIvy85 said:
More things I have tried:
-All of the above steps on a different computer
-Sweet talking it
-Talking dirty to it
Am I brick'd? I figure not, since I can at least get into download mode. Not sure what else I can do though. I'd go see what the Sprint store can do for me, but on the download mode screen it lists my custom binary download count as 5, I understand they will see that and tell me I'm out of luck?
Click to expand...
Click to collapse
Try to reset your binary counter with a usb jig.
you could try and download the drivers again from here and see if it then connects
http://modem-techno.blogspot.com/2010/09/epic-4g-usb-driver-download.html
I also had a similar problem once with an old i9000 and what worked was doing this and then connecting the phone first and then opening Odin.For some reason opening Odin first and connecting wouldnt find the phone.If nothing else works try wipeing the bin counter with the jig and send it back.Youll have to say that kies crashed while updating on Win7 64bits.Samsung know that before the September 30th kies update kies wasnt fully functional with 64bit drivers and they had a few phones replaced under warranty because of crashing kies updates on Win7 64bits.
Thanks for the replies everyone.
I made a USB jig but it had no result. I checked the resistance with a multimeter and I am connected across pins 4 and 5 of the usb dongle I bought. I plug it in and nothing happens.
I can still get into download mode by the usual means, just no recognition from my computer, odin, or kies. Very frustrating. Am I going to have to buy a new one or is there another way to reset the bin counter?
EDIT: Got the USB jig to work! I was using a bad diagram and was on pins 1/2 instead of 4/5. Now I can't boot, can't get to recovery, can't get any PC to recognize my phone in download mode.. but at least my download screen says "Custom binary download: NO." So if nothing else works before tomorrow evening I'm gonna bring this thing back to the Sprint store and tell them what cooza said about kies crashing on win7 64 bit. Thanks everyone! Also I just realized there is a specific forum for Epic 4G touch.. sorry >.>
The good thing is that your bin counter is at "0" again.The Kies thing is the real deal as there are also posts here on XDA of the same thing happening.I also know its true from first hand experience as it has happened to me and when i told them about the Win7 64bit driver problem (this happened to me a couple of months back too) they had no option but to accept it cos they know its true.Also i offered to e-mail links from forums with other complaints from users on 64bit PCs but they didnt even dought my storey and in 4 days it was back in my hand.I told them that when the update finalized the programe froze and the phone rebooted to a black screen.Had to pull the battery cos it appeared to be dead and refused to reboot again.Important to say that you where on Kies prior to the update I mentioned.Ived update to the latest Kies and it works fine now on my Win7 64bit so be carefull there that date is important
Thanks cooza I really appreciate your help. I do have a couple questions though.
1. Is the update you are referring to an update to Kies software.. or an update to the Galaxy S2? Reason I ask is because my phone is the Epic 4G Touch (accidentally posted in this forum >.>), will they still believe my story?
2. Not sure if you will know the answer to this one, but should I go through Samsung tech support or can I take it back to the Sprint store where I bought it?
3. Just trying to get clear on the story I should tell them. I was using Kies to update my phone on a Win7 64bit computer, but I accidentally used the version of Kies from before the Sept. 30 update? And then the phone crashed resulting in it's current state. Correct? Anything else I should watch out for?
4. With the problem you are describing with Win7 x64, does the phone go into a soft brick where it won't boot up?
Thanks again.. you've been very helpful
OperationIvy85 said:
Thanks cooza I really appreciate your help. I do have a couple questions though.
1. Is the update you are referring to an update to Kies software.. or an update to the Galaxy S2? Reason I ask is because my phone is the Epic 4G Touch (accidentally posted in this forum >.>), will they still believe my story?
2. Not sure if you will know the answer to this one, but should I go through Samsung tech support or can I take it back to the Sprint store where I bought it?
3. Just trying to get clear on the story I should tell them. I was using Kies to update my phone on a Win7 64bit computer, but I accidentally used the version of Kies from before the Sept. 30 update? And then the phone crashed resulting in it's current state. Correct? Anything else I should watch out for?
4. With the problem you are describing with Win7 x64, does the phone go into a soft brick where it won't boot up?
Thanks again.. you've been very helpful
Click to expand...
Click to collapse
Kies via to its Sep 30th update was not fully compatable with 64bits and gave a lot of problems to a lot of people.I had a few problems with it when I got a new laptop (HP Win7 64bit) so started searching the web for solutions and found that kies was designed mainly to support the windowsXP versions 32bit and had caused Samsung to accept various repairs under warranty because of crashing Kies updates mainly on android running phones.For some reason Bada didnt seam to affected.Maybe cos there arnt to many around like android.In the 4G forum there is post from someone who has bricked their phone using Kies to update and a reply from another with the same problem.Take it into where you bought it to start with and if its not there problem then they might send it back to Samsung for you.All you need to say is that you where updating your firmware via kies and on completion it froze and the phone booted to a black screen like mine did.You had to pull the battery and restart your PC to close Kies cos it wouldnt close or minimize or anything.Tell them that you searched on the net for possible causes and found what i told you about Kies and since you have a Win7 64bits PC then thats most likely to have been the cause.Your bin counter is at 0 so there is no way they can counter-attack your story.
OperationIvy85 said:
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Click to expand...
Click to collapse
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Who told you that the exclamation point means you voided your warranty?
bajaber said:
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Click to expand...
Click to collapse
The exclamation point on a normal boot up screen (Galaxy S II splash screen) means there is a custom rom installed. This can be removed with a USB jig, which will also reset your custom binary counter.
I have absolutely no idea still what [phone]....!....[computer] means though. I ended up taking my phone back to the Sprint store and they replaced it for a small service charge while telling me next time I won't be so lucky. My next step was going to be to try calling Samsung with the story cooza suggested. I told that same story to the people at Sprint but they definitely didn't buy it, but you may have better luck with Samsung. If you get this resolved I'd be curious to hear how, but I am not optimistic for you
bajaber said:
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Click to expand...
Click to collapse
The sign you see means that your phone is semi-bricked and that you needed a jig to force the phone to boot into download mode.You can buy one on ebay for a couple of bucks.Best you do cos it could may mean that your warranty is void.Let me explain,no one can actually say that your warranty is void because of this sign but being only "semi-bricked" the service centre are still able to enter the phone and see the bin counter.So if you semi-bricked flashing a non official firmware or you have done so earlier and your bin counter is not at 0 then YES your warranty is void.Semi-brick is not so bad as you can normally fix it yourself but Hard-brick is a dead phone and you gotta pay for a jtag .In your case buy a jig force the phone into download mode and re-flash it yourself.You shouldnt need to go anywhere.Semi-bricking is something you save yourself.Just wait till the jig arrives in the mail.
EDIT:there have been posts of people pulling the battery for 10min and re-trying and it has booted to download.They say they have had to do so 4 or 5 times for it to finally work but if youve got time on your hands then give it a try.
---------- Post added at 04:48 PM ---------- Previous post was at 04:22 PM ----------
OperationIvy85 said:
The exclamation point on a normal boot up screen (Galaxy S II splash screen) means there is a custom rom installed. This can be removed with a USB jig, which will also reset your custom binary counter.
I have absolutely no idea still what [phone]....!....[computer] means though. I ended up taking my phone back to the Sprint store and they replaced it for a small service charge while telling me next time I won't be so lucky. My next step was going to be to try calling Samsung with the story cooza suggested. I told that same story to the people at Sprint but they definitely didn't buy it, but you may have better luck with Samsung. If you get this resolved I'd be curious to hear how, but I am not optimistic for you
Click to expand...
Click to collapse
Well at least you got a phone now hope they didnt charge to much!!!!Good on ya mate
Update on my issue....
It turns out the problem is because I tried to flash an I1900 firmware while my phone is a G variant (I900G).
After using the right firmware, it worked.
OperationIvy85 said:
Thanks for the replies everyone.
I made a USB jig but it had no result. I checked the resistance with a multimeter and I am connected across pins 4 and 5 of the usb dongle I bought. I plug it in and nothing happens.
I can still get into download mode by the usual means, just no recognition from my computer, odin, or kies. Very frustrating. Am I going to have to buy a new one or is there another way to reset the bin counter?
EDIT: Got the USB jig to work! I was using a bad diagram and was on pins 1/2 instead of 4/5. Now I can't boot, can't get to recovery, can't get any PC to recognize my phone in download mode.. but at least my download screen says "Custom binary download: NO." So if nothing else works before tomorrow evening I'm gonna bring this thing back to the Sprint store and tell them what cooza said about kies crashing on win7 64 bit. Thanks everyone! Also I just realized there is a specific forum for Epic 4G touch.. sorry >.>
Click to expand...
Click to collapse
Hi, I'm having an exactly same problem with you and I just got a USB jig in mail, but even though I am following the instructions for the USB jig the counter is still not going back to 0 :/
This is the instruction I followed: take battery out for like a minute -> put the battery in but don't turn phone on -> put the usb jig in -> it's supposed to boot up with 0 flash count?
Mine still says 4... Can anyone please help?
sfoksn said:
Hi, I'm having an exactly same problem with you and I just got a USB jig in mail, but even though I am following the instructions for the USB jig the counter is still not going back to 0 :/
This is the instruction I followed: take battery out for like a minute -> put the battery in but don't turn phone on -> put the usb jig in -> it's supposed to boot up with 0 flash count?
Mine still says 4... Can anyone please help?
Click to expand...
Click to collapse
Is yours a i9100? If so is your firmware the latest 2.3.5 KI3 or KI8?
Could be your device has the new bootloader. If so check intratechs original firmware thread in original development section and install his old bootloader via Odin. Have a read while your there to get the latest info.
Good luck
Sent from my GT-I9100 using XDA App
aceofclubs said:
Is yours a i9100? If so is your firmware the latest 2.3.5 KI3 or KI8?
Could be your device has the new bootloader. If so check intratechs original firmware thread in original development section and install his old bootloader via Odin. Have a read while your there to get the latest info.
Good luck
Sent from my GT-I9100 using XDA App
Click to expand...
Click to collapse
Yeah, I got stuck while flashing 2.3.5 Gingerbread... Yeah I think it has a new bootloader, as I remember Odin updating the bootloader section before messing up.
Is there any way I can get the USB jig to work? My phone is no longer recognized by the USB anymore so I can't even flash another bootloader or anything.
Is there anythign I could do to make the USB jig work without connecting it to the computer?
Can you get into download mode using the buttons?
Volume down+home+power
If so try and flash another Rom from intratechs thread to get back to stock.
If that works you can try again.
Sent from my GT-I9100 using XDA App
Ok, so I have a serious problem... My phone is locked and when I touch the text bar to enter the password, no keyboard comes up. Important information:
- I just upgraded to jelly bean (the official one that came out today)
- as far as I can tell, everything is working fine, i just can't unlock it
- when I touch the text bar, it makes a noise, but no keyboard comes up
- was working fine immediately after the upgrade
- I got done fixing some settings and locked the screen
- this may have something to do with changing the default keyboard to Google Keyboard (it was acting a little funny immidiately after, like it was crashing)
- I have Android Lost installed, the unlock function isn't working, but others do work
- phone is encrypted
Unless someone has some ideas for me within the next couple hours, I'm going to wipe the phone. Obviously, I would prefer to not do that.
==========================
EDIT:
I've managed to use Android Lost to make some backups of some stuff, but I'm still trying to figure out how to unlock the screen. I've found that I'm able to install apps remotely from google play if that gives gives anyone some ideas.
=============================
EDIT2:
I had another idea. If this is a problem with the keyboard, is there a way for me to change it remotely? Can I install another one via the store?
Alright... I gave up on trying to get passed the lock screen and tried doing a factory reset. I was afraid of the super brick issue, so instead of doing a wipe in recovery mode, I used Kies to reflash it. However, that did nothing. The phone started back up and acted like nothing happened. It asked me for the same password, then got to the lock screen and had the same keyboard issue.
I've tried various roms, but nothing seems to wipe the encrypted information properly. At some point, I got it to forget the password, but it still thinks that one exists. I even rooted it and tried shostock3, but when it boots, it asks for a password. The old password doesn't work, so I can't get passed it. I tried entering the "wrong" password many times and it said it would wipe the phone, but it just restarted to the SAMSUNG boot screen and just sat there. I pulled the battery after half an hour...
I should note that stock gingerbread seems to work fine...
Does anyone have any ideas on how to wipe the encrypted data?
If you can push apps to it, try pushing an app like no lock or something.
Short answer: No.
It is probable that encryption information is stored in the efs (encrypted file system) folder. That's where the imei and other critical stuff is stored. I don't believe anyone who posts here in the I777 forum really has a grasp on how phone encryption works though. I've only seen one other person post here who had an issue with an encrypted phone, and he was unable to solve his problem as far as I know.
If you have a proper backup of the efs partition from before the phone was encrypted, it is possible that you could solve the problem by restoring that partition. But I'm not even sure you could write to that section of the phone memory with adb with the phone in it's current state. Edit: if you can boot into stock gingerbread normally, then you can restore an efs backup, if you have one.
I'm guessing you could send it to Samsung and they could fix it for you probably.
I finally got it working. I'm not sure what combination of things did it, but I had to restore it to stock jelly bean (via kies) to get it to wipe the encryption. I guess the stock rom knows how to properly wipe it when you keep entering the wrong password. After I got it all cleaned up, I put shostock3 back on. When the battery charges back up, I'm going to try encrypting it again (in shostock).
However, now I found another issue (may or may not be a real problem). I wanted to check if the phone was still unlocked, so I dialed *#SIMLOCK# and it says "Connection problem or invalid MMI code."
Tada!
Creepy, my good friend, would be referring to me and as you know SCIU I didn't ever get it to unlock the phone. Oddly enough a stock ICS rom (my mom now has my phone right up the road so I may try this to see if it will work and then go back to ShoStock3) works fine. I have nothing hidden from the phone storage, everything shows up, it is actually unlocked and rooted though not a custom bios err firmware/ROM because when that is put on there the encryption issues come back and the password is asked for. If the correct password is entered (and my KEYBOARD comes up but I didn't change it from the Android/Samsung one) it proceeds to enter whatever it is supposed to (my guess is the POST area like on a computer when it is entering Windows/Linux, etc.) but the screen stays black (ShoStock logo doesn't even appear if I remember correctly or it does show then goes to black loading screen with the Samsung logo and that is it, perm stuck). However I did try flashing back to Gingerbread ROMs and ICS ROMs though not through official KIES.
SCIU I may have to give this a try if my mom don't mind it and see if that helps fix the problem. Thanks for starting this thread. I am sorry I didn't respond to the PM you sent me (my LGOG, Triple OG, OG, TRIPLE OG, Optimus G AT&T Phone has screen cracked twice and is unresponsive on two different phones so I sent that in to warranty repair [rapid heating and cooling issues]) and haven't been on XDA for a week. If there is anything else you need to ask or bounce ideas off of me then I am all for it.
As far as encryption goes, the process works the same as any other encryption algorithms used (MD5/HASH/SHA-!, etc.) using a basic replica of most file systems although mobile storage tends to work a tad differently. Unfortunately, the freezer trick, brute force, nor any other cracking methods I was able to try at home worked to get it to open up. I tried getting into the EFS area of the phone but never could get to the directory or have it display.
Again thanks SCIU and as I stated I may give this a try if my mom don't care.
Eagle
i've the same problem here but i cann't use kies when my phone is locked .... so what can i do??
rawan-omer said:
i've the same problem here but i cann't use kies when my phone is locked .... so what can i do??
Click to expand...
Click to collapse
You can get the full stock jelly bean Odin flashable tar in the Download Repository. See link in my signature. According to sciguy125, flashing stock jb and then inputting repeatedly the wrong password will clear it. I'm not sure how many times it takes, 5 or 10 I think. I've never worked with an encrypted phone. I'm just repeating what I have read others say. I've seen the above posted by at least one other person. You should be able to flash the stock firmware using Odin. The one you want is I777UCMD8
my phone screen is locked (with word password) , Huawei, and the keyboard doesnt show up when i click the box? tried reseting it, cant go to settings whatsoever! i didnt damage my phone in any way either. need help asap!!
moselyy said:
my phone screen is locked (with word password) , Huawei, and the keyboard doesnt show up when i click the box? tried reseting it, cant go to settings whatsoever! i didnt damage my phone in any way either. need help asap!!
Click to expand...
Click to collapse
Friend, this is the forum for the S2 (Samsung), so you won't find anything about Huawei devices here - best to ask your question in the forum for your device.
That being said if you are rooted and have a custom recovery, simply power the device off and boot into recovery and perform a factory reset from there. If that doesn't work do a full wipe (this means wiping /system), then re-flash the ROM/gapps.
me too!!! do you have some tips for me?? i almost fainted when i knew that the keyboard isnt working.... i do have a lot of important files in my phone.
Easy, you fools! JUST KIDDING lol Connect an external keyboard. Restart the phone with the keyboard plugged in and you'll have one chance to input the pass every time you restart. Good luck, bosses!
my phone screen is locked (with word password) , SAMSUNG GALAXY TAB 3V, and the keyboard doesnt show up when i click the box? tried reseting it, cant go to settings whatsoever! i didnt damage my phone in any way either. need help asap!
My sumsang keyboard has stopped I cannot do nothing because is secure by password can you help please
I got the same problem but everything on my phone is fine except it doesn't let me enter the password I dnt wanna factory reset it cause I got important pictures in it any suggestions on how to get my keyboard working.
Solution that worked for me
Hello all,
I usually don't post things around, but something told me to do this, since I don't see any threads talking about this solution.
My solution was the following:
Went to google play store on my computer via chrome. Logged in to the user attached to my play store and re-installed all keyboard apps I have.
That worked beautifully and hope this helps other people!!
Hi,
BeforeI begin I would like to state the I have searched the forum for solutions but the ones i findthe person can get into DL mode the only one that is just like my issue doesnt show how ODIN worked for him. but anywho...
I have a Glaxy SGH-I717 and it is stuck at the "FIRMWARE UPGRADE ENCOUNTERED AN ISSUE. PLEASE SELECT RECOVERY MODE IN KIES & TRY AGAIN."
How this started was I newly installed Kies and tried to back it up, but by mistake started to upgrade it. not wanting to mess up the phone I let it run without the phone being in download mode. after a bit the upgrade failed and my phone was stuck at the error message screen above. to reboot the phone i have to remove the battery. pressing the button on turns it off but back on at the error screen. my computer makes the sound like it recognizes the phone but doenst show it in my computer. Kies just says connecting for awhile then stops.
Things I cant do with the phone
- get into download mode - when trying it goes the the press up or down button (ethier one goes to error screen)
- get into recovery mode - the samsung logo flashes for a second then goes to the error screen
things i have tried
- Using oding to flash ROM(tried two different files both from da_g for flashes)
each time odin states it failes at the write stage
- Kies emergency recovery (it freezes at 0% somtimes it says the phone is disconnected)
- Used one click fix program (made me click more then once)
I'am curently looking into trying the adb solution usind android sdk. just making the post here to see if anyone knew a easier solution to this.
Fixed
Problem is fixed, switched USB ports and found a different ROM to flash in ODIN. I now see why people love ODIN better then Kies
heelllp
Rremann1 said:
Problem is fixed, switched USB ports and found a different ROM to flash in ODIN. I now see why people love ODIN better then Kies
Click to expand...
Click to collapse
what ROM did you use? where can I find it? I have the same problem you had, except I was only trying to hard reset the sgh-i717 but the only option I could seem to get to was "A custom OS can cause critical problems in phone and installed applications. If you want to download a custom OS, press the volume up key......" etc This is my friends phone I was just trying to hard reset it because she forgot her pattern lock, so I downloaded a ROM and odin and when I attempted to flash it, it got to that error screen you had. It lets me get back to the previous screen but always goes back to firmware upgrade issue screen no matter if i choose up or down. :crying: I have flashed a couple phones before by following tutorials on the web. I though it was only giving me that option because the phone might have already been rooted, it never let me go to the wipe data menu. The instructions all said to hold volume up + home + power, it never did anything for me. I was only able to get to the custom OS screen by holding volume down and power button. you were able to get back to the ready to flash screen? Tried taking out the battery and turning off with power button always goes back to Firmware upgrade encountered. Please help if you can, if I am breaking some forum rules sorry! just need help! Am running windows xp, since the phone was loccked have no idea what it was running, just that its an att samsung galaxy note sgh-i717. it saysin odin mode, custom binary download: no, current binary : samsung official.
thank you!
---------- Post added at 10:50 PM ---------- Previous post was at 10:03 PM ----------
tech_girl85 said:
what ROM did you use? where can I find it? I have the same problem you had, except I was only trying to hard reset the sgh-i717 but the only option I could seem to get to was "A custom OS can cause critical problems in phone and installed applications. If you want to download a custom OS, press the volume up key......" etc This is my friends phone I was just trying to hard reset it because she forgot her pattern lock, so I downloaded a ROM and odin and when I attempted to flash it, it got to that error screen you had. It lets me get back to the previous screen but always goes back to firmware upgrade issue screen no matter if i choose up or down. :crying: I have flashed a couple phones before by following tutorials on the web. I though it was only giving me that option because the phone might have already been rooted, it never let me go to the wipe data menu. The instructions all said to hold volume up + home + power, it never did anything for me. I was only able to get to the custom OS screen by holding volume down and power button. you were able to get back to the ready to flash screen? Tried taking out the battery and turning off with power button always goes back to Firmware upgrade encountered. Please help if you can, if I am breaking some forum rules sorry! just need help! Am running windows xp, since the phone was loccked have no idea what it was running, just that its an att samsung galaxy note sgh-i717. it saysin odin mode, custom binary download: no, current binary : samsung official.
thank you!
Click to expand...
Click to collapse
I have read several forums searching for answers, no one ever stated that odin will still work while on the screen that said "Firmware upgrade encountered an issue..." pretty positive it flashed the lock screen background and the user settings that were on the lock screen are no longer there it had said something to the effect of " ____ password protected!" ill leave the blank up to your imagination. The user settings are gone but not the pattern lock! all I want to do is hard reset to eliminate the lock pattern lock???
Thanks
ROM Link
tech_girl85 said:
what ROM did you use? where can I find it? I have the same problem you had, except I was only trying to hard reset the sgh-i717 but the only option I could seem to get to was "A custom OS can cause critical problems in phone and installed applications. If you want to download a custom OS, press the volume up key......" etc This is my friends phone I was just trying to hard reset it because she forgot her pattern lock, so I downloaded a ROM and odin and when I attempted to flash it, it got to that error screen you had. It lets me get back to the previous screen but always goes back to firmware upgrade issue screen no matter if i choose up or down. :crying: I have flashed a couple phones before by following tutorials on the web. I though it was only giving me that option because the phone might have already been rooted, it never let me go to the wipe data menu. The instructions all said to hold volume up + home + power, it never did anything for me. I was only able to get to the custom OS screen by holding volume down and power button. you were able to get back to the ready to flash screen? Tried taking out the battery and turning off with power button always goes back to Firmware upgrade encountered. Please help if you can, if I am breaking some forum rules sorry! just need help! Am running windows xp, since the phone was loccked have no idea what it was running, just that its an att samsung galaxy note sgh-i717. it saysin odin mode, custom binary download: no, current binary : samsung official.
thank you!
---------- Post added at 10:50 PM ---------- Previous post was at 10:03 PM ----------
I have read several forums searching for answers, no one ever stated that odin will still work while on the screen that said "Firmware upgrade encountered an issue..." pretty positive it flashed the lock screen background and the user settings that were on the lock screen are no longer there it had said something to the effect of " ____ password protected!" ill leave the blank up to your imagination. The user settings are gone but not the pattern lock! all I want to do is hard reset to eliminate the lock pattern lock???
Thanks
Click to expand...
Click to collapse
Hi I am sorry if this is hard to read i' am a little bit ____ ill leave the blanks up to your imagination. below is the link to where u can use the rom i used. and yes you can run odin on the error screen.
go to this site download pdr.tar there's a link for odin as well. GL
Hope this helps ^^
Sorry to rez such an old post but i broke screen on my current phone and needing another phone asap I ventured into the big bin labeled Misc Phone Parts and all i could find (screen came on)was my old Note. Popped in in Sim using an adapter.
And thought i was good until I saw Phone icon dots Yellow triangle dots PC monitor. Firmware Upgrade encountered an issue. Please select recovery mode in Kies & try again.
After about 6 hours I do not have it working. I am not new to samsung flashing having flashed my first phone 4 years ago and since then installed 30 plus custom ROMS on all my Galaxy phones through out the years. Sure I can just find used much better phone but then this will not be resolved and will keep me up at night. (if your like this you know what I am talking about).
So back on XDA where I am thankful and appreciate all the members who have contributed helpful information that has saved this world from filling with an ocean of frustration. Myself being one of those who has been saved many times by reading and following directions of what others have done. I like to think that a persons efforts to help someone last well beyond their own lifetime. Thank you sir or miss (yes you) for the work done selflessly with out recognition and reward that continues to help make the lives of others who they may never meet or know better and more happy.
Hey, so I was trying to flash my friend's s3, and apparently, I did something wrong which got me stuck up at odin mode.
Initially, I could hold the vol up + home + power button to go to recovery, but now, even that won't work as it would just show me
Samsung's logo and a red exclamation mark on top left corner.
I've downloaded the firmware stock and tried to flash it using odin however it just won't work.
It says "NAND Write Start!!!" and it just stops there (stuck forever). It should (as I know it) show a progress bar on my android and
on it's interface to tell how much it has been done, but as soon as I start, the progress bar instantly fills up (on my android, the blue line)
and its just stuck there.
I've tried to take out the battery, clear cache/reset factory, take out sd and sim. But it simply won't work.
It's just stuck on "Downloading....do not turn of target!!!"
I cannot even get the flash counter to reset (I don't know how, since I can only open up odin mode)
counter: 4
binary: yes
Currently, I don't even know if it's suppose to be charging or the battery is just draining out.
Region for this phone is Turkey.
Yes I've also unrooted the phone using KingoRoot (previously, when it could go into recovery) but no luck.
Note: I have searched other threads on this forum but I cannot get anywhere around even close to fix my device.
It's soft-bricked (I assume, of course it is).
Any idea how to fix this?
Odin Screenshot (since it's my first post, it won't allow me to post outside links, sigh,):
http: // i.imgur .com/eBVZ3NN . png
^^ Just been stuck there....
Meanwhile on my android, it just shows a full-blue progress bar. And that downloading do not turn of target.
UPDATE:
THE PROBLEM HAS BEEN RESOLVED. I DOWNLOADED A CUSTOM FIRMWARE, (LUCKILY, CLOCKWORK MOD WORKED, JUST HAD TO WAIT AFTER GOING TO RECOVER)
FLASHED IT THROUGH THERE, WAITED FOR IT TO INSTALL, RESTART. BAM.
Did the 'something wrong' include flashing a firmware for another model?
What does the model number in download mode read?
You can try the rescue firmware, search general forum,.
Yeah, wrong firmware I suppose
boomboomer said:
Did the 'something wrong' include flashing a firmware for another model?
What does the model number in download mode read?
You can try the rescue firmware, search general forum,.
Click to expand...
Click to collapse
I was seeing this tutorial on how to install KitKat (4.4.4) on Galaxy S3. I must've made a mistake while trying to do so.
In other words, yes, flashing a firmware for another model.
You have a hard brick, sorry.
Yeah, no.
boomboomer said:
You have a hard brick, sorry.
Click to expand...
Click to collapse
No I don't lol. The problem has been solved anyway.
Im' glad to see you didn't give up on this, and came back to let us know what was wrong
I know this could be seen as off-topic, but the reality of devices becoming bricked isn't really possible luckily, it just takes longer to get around sometimes. If the item is worth fixing, then I always say keep at it, because I've never had an android device stay stuck so far. The only thing that really went nuts and refused to work, were 2 of the Iconia A500 tablets that lost access to their memory - but this is a common hardware fault as the RAM chips break away and need reflowing before you can even format the internal memory (it cant even see the SD cards either because the RAM comes and goes - same idea as plugging/unplugging a USB drive in Windows/Linux - it just doesn't know what to believe lol).
Great forum by the way, there's so much great information on here I get lost reading
Hi guys, sorry if I posted this at the wrong place.
I have a Lenovo s860 and it went into a bootloop. It was stock and all so I thought that I can have my files recovered if I just bring it to a service center so they can get the files first before wiping it or maybe even fixing the bootloop without wiping the device. Well, the thing is, the guy at the service center screwed up and now, when I try to turn it on, I still see the boot screen (Lenovo, powered by Android) but the next screen is like an television with bad signal.
I'm familiar with rooting and flashing ROMs, I've tried it on my Galaxy S2 (yeah I know, it was way back), but I think things are still more or less the same: I need to be able to boot into recovery mode in order to root the device. However, when I tried the Power Button + Volume Up, or any combinations of the Power Button and the Volume Buttons, it just goes straight to the dead screen, I get no response whatsoever.
I also tried to check if adb can detect it, however, it didn't seem to be able to do so. I'm using a MacBook Pro so I know I don't have to install any drivers, I also code Android Apps so I have a background on this.
I think my only option would be to flash the ROM on this dead device but I don't know how to do that. I've also seen some posts that suggest doing some things (I forgot the specifics) while the battery is drained, so what I'm doing for the mean time is to leave the phone open and let it drain which might take ~2 days.
Does anyone know how to flash a ROM on a bricked device? Thanks for any leads.