couple days ago i tried to update it and it must of been the wrong firmware as now i have no blue light or picture
i tried to flash it with amlogic usb burning tool but it gets stuck at 2% and says usb control setup error
any help appreciated
Its good that u can still flash via usb burn tool.
Try another firmware .
Usually happens when u try to flash wrong file
Related
Hi
Sorry to bother, but i just got a new Star B92M but im having a rough time trying to update it and flash it with SP Flash Tool
So far, i have tried this
To flash with the SP_Flash_Tool_v3.1224.01 (i get BROM 3013 error)
To flash with the SP_Flash_Tool_v3.1224.0.sn85 ( i get the 8038 error)
I have tried to run each of them as administrator
I have tried to click on Firmware-> Upgrade as someone suggested on a post
I have installed the preloader drivers
I have tried by taking our the battery and plugging in then put the battery on
But i havent been able to flash it. The phone is not bricked, it runs as nothing has happened, i do think although, that recovery is messed after so many tries since there is the red triangle when i try it.
I dont know if it is normal, but everytime i plug the phone when its off for flashing, is like it gets connected by usb for 2 seconds then disconnected, but its weird because when the phone is on, the usb works like charms, no problems on computer ports either or the usb cable, it just happens when i connect it when the phone is off (preloader i guess), yet i have installed the proper drivers read in many tutorials
Is there any other way to flash it? or any solution to this problem? Sorry for the bad english
Thanks in advance.
Hi , so i buy leagoo lead 1 from Etotalk they send me phone and everything was ok , but after 2 weeks i got OTA update which i download and click on apply , phone restart and start again instaling new update (i was like ok everything is good )but at middle of this update it give me Error Android icon with red color ,
and after that i can just start phone again and see just boot menu with :
otd leagoo lead1 sm619b v0.9.2_S1202
Normal Boot
Update via ADC
Update from sdcart
update from cashe
wipe cashe
wipe data (factory reset)
....(this one last i dont rememeber)
I tried wipe all and restart again but that did not help me much ..
ok so i download SP-flashtool from Leagoo web site instal all driver for usb and download Original rom from theyr site too .
what i did is i start program like admin. then i click on Option->be sure that Usb mode is enable then again Option -> DA Download All-> and enable Hight speed , after that i click on Scatter -loading and from the folder with Rom i sellect "MT6582_Android_scatter.txt"click on Firmware ->Upgrade and plug my phone which is turn off . in program i can see that he fount it but after 2 hour it is still at 0% how u can see on image i attach to this with some txt record from program with errors
So could anybody tell me what should i do now ?
try different (and newer) sp flashtool:
SP_Flash_Tool_v5.1348.00
https://drive.google.com/file/d/0BwtGwuP0GdfBZzh3a2NCWVZ3RVU/edit?pli=1
r0c0 said:
try different (and newer) sp flashtool:
SP_Flash_Tool_v5.1348.00
Click to expand...
Click to collapse
i will try but now i got another problem so i cant turn off my phone with usb cable plug in , i can see batery logo or i just turn it on * unlycky me but for half sec when phone was plug in with meadiatek preloader i saw it working for 1 secunde u can see on my printscreen
you need to plug in a usb cable and really fast press download button in flash tool, this helps with BROM errors. otherwise you could try googling the error or just contact leagoo.
r0c0 said:
you need to plug in a usb cable and really fast press download button in flash tool, this helps with BROM errors. otherwise you could try googling the error or just contact leagoo.
Click to expand...
Click to collapse
Yeah i try today and after some time i did it , i use official rom from web site , all file load dormat etc , then green cirle "OK" i unplug phone from usb and turn it on but i saw that logo "LEAGOO" was flickring and then top half display of mobile was Yellow and bottom was white/black thats maybe worst then before i emailing with seller too but i dont think he could help me
and after that with another try i waned use different rom i got this pic down .. so again im on connect disconect phone
after 10+ try i connect it again and trying another rom hope this will work :silly:
1st edit: add img after ok flash
2nd edit k phone after turn on is yellow at top and at bottom white black
should i use download only or try format all+ download
3th: i upload img of phone after start so u can see
its to bad that ppl from etotalk dont know how to deal with it too
i got the same problem
i was flashing lead 1 firmware on lead 1i
lead 1i is the latest so download right firmware..
FLASHED 2.DUMP_ROM [SPFT][ROOTED] FROM All About CherryMobile Flare 4 AFTER IT SAYS FLASHING IS DONE 100% WITH CHECK MARK THEN MY PHONE DIDNT RESTART I WAITED FOR ABOUT 15 MINUTES TO SEE IF THERE'S SOMETHING MIGHT HAPPEN BUT NOTHING ONLY BLACK..
SO I PULLED THE USB CONNECTOR, THEN PLUG IT BACK. THE ONLY THING THAT I SAW IS UNRECOGNIZED USB. NO CHARGING LOGO OR ANDROID OR ANYTHING EVEN THE LED INDICATION OF CHARGING IS NOT BLINKING.
I HOPE SOMEONE CAN HELP ME :crying::crying::crying::crying::crying::crying::crying:
UP
I also had the same problem and I also cried. Your phone have MediaTek MT6753 Chipset. I have MT6582. You flashed ROM via recovery and looks like ROM have conflict with bootloader.
SP Flash Tool can flash shutdown MTK devices via USB. Your computer show "UNRECOGNIZED USB". SP Flash Tool need special ROM and driver to find your phone. Not sure, that SP Flash Tool can help you, but it helped me.
How I decided problem:
I waited some time (I went sleep, it was night)
Found stock ROM for Flashtool. This ROM contain all data for device and have more size.
Install driver for my phone.
Pulled out battery.
Connect with computer via USB.
Put in battery and computer detected phone as "MediatekDevice". SP Flash tool also detected phone
Started flashing.
Good luck!
AlexanderBabansky said:
I also had the same problem and I also cried. Your phone have MediaTek MT6753 Chipset. I have MT6582. You flashed ROM via recovery and looks like ROM have conflict with bootloader.
SP Flash Tool can flash shutdown MTK devices via USB. Your computer show "UNRECOGNIZED USB". SP Flash Tool need special ROM and driver to find your phone. Not sure, that SP Flash Tool can help you, but it helped me.
How I decided problem:
I waited some time (I went sleep, it was night)
Found stock ROM for Flashtool. This ROM contain all data for device and have more size.
Install driver for my phone.
Pulled out battery.
Connect with computer via USB.
Put in battery and computer detected phone as "MediatekDevice". SP Flash tool also detected phone
Started flashing.
Good luck!
Click to expand...
Click to collapse
thanks bro.
now it show dram fail (4032)
hello .
I have a problem after flashing this rom.
I flash the rom via usb burning tool.
but at the moment to remove the bootloader, the box is disconnected from the pc and so there was an error message.
since, I have no more signal on the hdmi of my television!
I managed to flash the rom again but nothing to do, still no hdmi signal.
Do you have a solution?
PS: Would it be possible to have a link to a stock rom to restore everything again? thank you .
EDIT: i have flashed a stock firmware and the CVBS (av) signal work but the hdmi dont work animore!
up, noting?
Same problem here... someone could help? No Screen , tried to unbrick by flashing stock Firmware via Burn Card Maker and USB Burning Tool.
Have no Logo Screen, no Recovery screen , nothing...
:/ TeVioN
Use this
https://forum.xda-developers.com/an...m-xtmod-atv-x96-max-gt1-u211-devices-t3892273
I have a T9 4GB/64GB TV BOX (RK3328) TV stick, it got bricked. I tried all method to get it boot in maskrom mode but no luck. was flashing firmware its failed.
now my box not turning on.
I used flash tool to flash T9-4_64-RK3328-6255-v9-1228_AndroidTVBox image file. I attached flash log file and board image
I have no ideas, anyone please help!
Same Issue with me. it is dead, if you have found any solution just tell me
I was able to get it in maskrom mode by shorting these point
zee95 said:
I was able to get it in maskrom mode by shorting these pointView attachment 5661685
Click to expand...
Click to collapse
Hi @zee95 , I have the same problem, I bricked it trying to flash it, now it doesn't turn on not even the boot led nor recognized by PC when I plugged it with usb
Can you guide me please with the steps you followed to unbrick, how did you shorten those points. Thanks in advance @zee95
How you are flashing rom ?
The one i used with an incorrect firmware was Factory Tool v 1.46.
After that the box never turned on, nor even the t9 boot screen or the blue front leds. Also unable to been recognized by any flash tool.
I have tried with SD Card with firmware (using Rockchip Create Upgrade Disk) , hit reset button and power on, but nothing.
Also tried shortening with a clip and needle the two points you mentioned in the picture and plug the power cable at the same time but nothing.
Regards
Having same problim
when ever i connect to pc its in maskrom mode and cant exit from it
plz help