Hello Guys i had the problem that i couldnt mount date and i found in a forum post a "fix" the command mke2fs -T ext4 /dev/block/mmcblk0p8 i entered twrp got to advanced then to terminal and entered it after finsihing i reboot my devices it vibrated and shut off only a blackscreen and a short vibration. Can anyone help me? thx Also when i try to charge it it vibrates stop vibrates and so on..also happens when connected to the pc.
Related
Yah,..
My X10, now stuck in Leter " Sony Ericsson " .
That's my false,..
I did the stupid step for put the files on system\Framwork...
Ok,.. Forgeted..
I need help now,...
1).How Put the Firmware-res.apk to system\Framework
Using ADB ,might not possible because the computer not recognize my x10 as ADB anymore , and usb debuging status was not checked .
2). I've tried using Update Service Setup.exe, but still got the problem on Power off the phone.
> As we know , shuting down/(power off ) by removing battery is not posible in this device.
Step for updating is :
-Press and hold back button on the x10, while pluging the usb cable into x10
-Continue holding back button until the NEXT
Simple or big problem?
> How to Power Off the Phone , since the phone was stuck in logo /"sony ericsson"
Thanks,...
Why not leave the battery to drain, then plug into the computer?
Dricos said:
Yah,..
My X10, now stuck in Leter " Sony Ericsson " .
That's my false,..
I did the stupid step for put the files on system\Framwork...
Ok,.. Forgeted..
I need help now,...
1).How Put the Firmware-res.apk to system\Framework
Using ADB ,might not possible because the computer not recognize my x10 as ADB anymore , and usb debuging status was not checked .
2). I've tried using Update Service Setup.exe, but still got the problem on Power off the phone.
> As we know , shuting down/(power off ) by removing battery is not posible in this device.
Step for updating is :
-Press and hold back button on the x10, while pluging the usb cable into x10
-Continue holding back button until the NEXT
Simple or big problem?
> How to Power Off the Phone , since the phone was stuck in logo /"sony ericsson"
Thanks,...
Click to expand...
Click to collapse
hold power + home. release it when screen goes off. hold back and plug usb in.
timing is all. i had to try it a few time before SEUS released the next button
advice to wait untill you drain the battery is not a solution, it will switch the device off after time, but after you start charging, you will get back to the same situation, the device will start and will get stuck on the same place as now (personal experience)
try this before you reflash you device..
If your phone gets stuck on booting after playing with framework or some other stuff, I've found a way to repair it without reflash :
restart phone, connect it to usb
in adb shell run rootshell command again to gain root (wise to keep it after rooting), the "su" won't work cause it depends on gfx libs and they are not started yet..
mount sdcard with this command : mount -t vfat /dev/block/mmcblk0p1 /sdcard
and put your backed files where they belong.
Good luck!
forced restart as already mentioned in post above, hold power button + home button
it's from this thread
inteks said:
hold power + home. release it when screen goes off. hold back and plug usb in.
timing is all. i had to try it a few time before SEUS released the next button
Click to expand...
Click to collapse
Thanks,
it's solved,...
And now my x10 already get normal again..
but, I have some question :
After SEUS, the buid number has changed to 1.1.A.0.8
( Before SEUS Build Number : 1.1.A.0.36 )
I don't not know what I did, means "downgrade ? " or update ?
darebak666 said:
advice to wait untill you drain the battery is not a solution, it will switch the device off after time, but after you start charging, you will get back to the same situation, the device will start and will get stuck on the same place as now (personal experience)
try this before you reflash you device..
If your phone gets stuck on booting after playing with framework or some other stuff, I've found a way to repair it without reflash :
restart phone, connect it to usb
in adb shell run rootshell command again to gain root (wise to keep it after rooting), the "su" won't work cause it depends on gfx libs and they are not started yet..
mount sdcard with this command : mount -t vfat /dev/block/mmcblk0p1 /sdcard
and put your backed files where they belong.
Good luck!
forced restart as already mentioned in post above, hold power button + home button
it's from this thread
Click to expand...
Click to collapse
Thanks, bro.. for ur advice,
My x10mini was reflashed now ,
It is unrooted phone now
I'll try rooting and try new themes I need your advice...
help help help !!!!! im having the same problem but i tried everything ! but it still dosent work
Simple way,...
Just go to sony ericsson web, and you get the driver and services update..
Update your device through the sonyerricson service updater...
I just got my gtablet, I had bought it used and it came with a ics rom, I had had it boot and reboot no problem, then I wanted to update the rom (as it had downloaded an update), so I had rebooted the tablet but I had accidentally booted into apx mode instead of the cwm mode and I haven't been able to find a way to exit. I have tried holding down the power button, but it doesn't seem to want to turn off. I tried hooking it to my computer where it asked for the apx driver so I thought I would just need to install that, I went home so I could try to run the procedure, and now it doesn't ask for a driver, pressing the power button does nothing, I have tried plugging it in to charge, and trying to go into apx mode or any mode for that matter and I got nothing, the screen remains black and I don't see a backlight... please don't tell me I bricked it....
I'm pretty sure it's turned on as if I plug in my thumbdrive the light blinks for a split second......
Update: Is definitely powered on, my light up game controller is lighting up if plugged in.
any ideas? Right now I'm trying the code triple red procedure.
... the battery in this thing is just freaking amazing.... I've charged my phone twice, had a light up controller plugged in for several hours and my ipod and it is still running....
thanks for any help you can give me
Yup the triple red plan worked the tablet is now working.... got stuck in the actual recovery (the one if you hold plus) while trying to power down so It's a portable charger again ... if anyone knows how to get it to power off properly in recovery let me know
Brainy142 said:
if anyone knows how to get it to power off properly in recovery let me know
Click to expand...
Click to collapse
Run these commands via ADB:
Code:
C:\SOME\PATH> [B]adb shell sync[/B] [I]Sync filesystems[/I]
[I]Then[/I]
C:\SOME\PATH> [B]adb shell reboot -p[/B] [I]Power off tablet[/I]
[I]Or[/I]
C:\SOME\PATH> [B]adb shell reboot[/B] [I]Reboot tablet[/I]
Thanks, I got stuck in recovery last time, so hopefully I'l be able to ADB the command to reboot next time .
Hi guys,
My friend had got a Tab from Dubai (Vendeor person unknown, abit strange).
He said it as Samsung Galaxy Tab 10.1 and when i had a look at it for the first time front and back (having the Samsung logo engraved at back) i thought it was true.
But the Tab is pattern locked and we hell donot know the pattern
When i tried to enter recovery mode (Vol- + Power) it didnt enter and then i tried Vol+ + Power so it enetered download mode and i did not have any control at that screen. When i connected to PC in download mode it the PC said M9701 connected (which is a chinese tablet)
When i booted it normally i never got a Samsung logo at any point (really strange thing).It has three kinds of android screens coming over while booting one had kw350.com logo at the bottom as a signature.
I am posting my db folder of the pics of the Tab and the booting process too.
https://www.dropbox.com/sh/selfv7ucuvjb5v5/Wy5kBTPQNw
I have booted into a mode (recovery/download doesnot know) by pressing Vol+ + Power. A android was shown sleeping and a red triangle mark on it. I successfully installed the adb drivers and adb detected the device in that mode as recovery device. But when i ran the command
adb shell
it said
--exec :/system/bin/sh not found
Click to expand...
Click to collapse
When i tried
adb remount
it said
Remount failed:Success
Click to expand...
Click to collapse
Please help me out...
Please help me identify it and i want to hard reset it to the factory settings.
Soryy for bumping this thread.... need the solution.. please...
I own many nexus devices, a heavy terminal user and I know about things like adb, fastboot etc.
This device Huawei mediapad 7 lite is driving me mad, I wanted to install CM 10.1 on it but I am unable to enter into fastboot mode. I have searched enough and tried all the methods like "adb reboot bootloader" and "volume up + power", but no luck at all.
Is there anything that I am missing? I am able to use 'adb' but rebooting into bootloader just power offs the device and sometimes just displays the battery charging icon on screen.
If I try "adb reboot recovery", it enters into recovery mode but within 2 seconds reboots. I somehow need to get into bootloader mode(fastboot mode) so that I can flash recovery and custom rom.
Your help is highly appreciated!
Thanks in advance
smartdipu said:
I own many nexus devices, a heavy terminal user and I know about things like adb, fastboot etc.
This device Huawei mediapad 7 lite is driving me mad, I wanted to install CM 10.1 on it but I am unable to enter into fastboot mode. I have searched enough and tried all the methods like "adb reboot bootloader" and "volume up + power", but no luck at all.
Is there anything that I am missing? I am able to use 'adb' but rebooting into bootloader just power offs the device and sometimes just displays the battery charging icon on screen.
If I try "adb reboot recovery", it enters into recovery mode but within 2 seconds reboots. I somehow need to get into bootloader mode(fastboot mode) so that I can flash recovery and custom rom.
Your help is highly appreciated!
Thanks in advance
Click to expand...
Click to collapse
Hi,
I am having similar problem for different reasons. I am in a reboot loop and if I try power+volume up I get this: Enter into fastboot mode. You can press POWER key for more than 10 seconds to reboot device.
Power for 10 seconds will reboot and go back to reboot loop, but anything else I try to push does not get me anywhere. In this state the tablet will not show through USB on the computer. I was trying to google how to enter bootloader, but I am not able to find any info plus screenshots. So if you find a solution, I would VERY happy.
I would keep you informed if I find something myself. Here is my post: http://forum.xda-developers.com/showthread.php?p=37646468#post37646468
Good luck.
Karel
kolibrik said:
Hi,
I am having similar problem for different reasons. I am in a reboot loop and if I try power+volume up I get this: Enter into fastboot mode. You can press POWER key for more than 10 seconds to reboot device.
Power for 10 seconds will reboot and go back to reboot loop, but anything else I try to push does not get me anywhere. In this state the tablet will not show through USB on the computer. I was trying to google how to enter bootloader, but I am not able to find any info plus screenshots. So if you find a solution, I would VERY happy.
I would keep you informed if I find something myself. Here is my post: http://forum.xda-developers.com/showthread.php?p=37646468#post37646468
Good luck.
Karel
Click to expand...
Click to collapse
Then you see on your tablet: Enter into fastboot mode. You can press POWER key for more than 10 seconds to reboot device. - then it means that you are already in fastboot mode. Holding power for 10 s needed to exit from fastboot (to reboot).
after_silence said:
Then you see on your tablet: Enter into fastboot mode. You can press POWER key for more than 10 seconds to reboot device. - then it means that you are already in fastboot mode. Holding power for 10 s needed to exit from fastboot (to reboot).
Click to expand...
Click to collapse
Thanks for the reply. Sorry if I sound like a novice, but what can I fo in fastboot mode? The computer does not recognize the device in this fastboot, so I can do anything from computer, and the tablet does not respond to anything pressed while in this mode.So how do I install recovery or do anything sensible? Sorry if I missed something obvious, it is my first Mediapad.
kolibrik said:
Thanks for the reply. Sorry if I sound like a novice, but what can I fo in fastboot mode? The computer does not recognize the device in this fastboot, so I can do anything from computer, and the tablet does not respond to anything pressed while in this mode.So how do I install recovery or do anything sensible? Sorry if I missed something obvious, it is my first Mediapad.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=37665946&postcount=51
All operations with fastboot should be performed via terminal.
Hello after_silence, any help for me? When I do "adb reboot bootloader", it shuts down and NOTHING comes up on screen. If usb cable is connected, it shows the battery charging symbol. When I do "sudo fastboot devices", nothing comes up. That means I am not entering into fastboot mode. Any other workaround?
Thanks!
Help
smartdipu said:
I own many nexus devices, a heavy terminal user and I know about things like adb, fastboot etc.
This device Huawei mediapad 7 lite is driving me mad, I wanted to install CM 10.1 on it but I am unable to enter into fastboot mode. I have searched enough and tried all the methods like "adb reboot bootloader" and "volume up + power", but no luck at all.
Is there anything that I am missing? I am able to use 'adb' but rebooting into bootloader just power offs the device and sometimes just displays the battery charging icon on screen.
If I try "adb reboot recovery", it enters into recovery mode but within 2 seconds reboots. I somehow need to get into bootloader mode(fastboot mode) so that I can flash recovery and custom rom.
Your help is highly appreciated!
Thanks in advance
Click to expand...
Click to collapse
Is There Any Solution To This? I've Been At It All night and No results
STUCK
JaleelAJames said:
Is There Any Solution To This? I've Been At It All night and No results
Click to expand...
Click to collapse
Been up tonight on The Evervolv screen, rebooted, still Evervolv screen
Sounds similar to your problem, cannot get any PC link, power and volume controls gets me to fastboot but the PC does not see the device
Retry, Retry, EvervvolLLLLL screen, nothing else
Any suggestions or tips
thxs
---------- Post added at 05:29 AM ---------- Previous post was at 05:15 AM ----------
hillbillie said:
Been up tonight on The Evervolv screen, rebooted, still Evervolv screen
Sounds similar to your problem, cannot get any PC link, power and volume controls gets me to fastboot but the PC does not see the device
Retry, Retry, EvervvolLLLLL screen, nothing else
Any suggestions or tips
thxs
Click to expand...
Click to collapse
Managed to pull back TWRP screen, wiped Dalvik, cannot mount external_sd, now waiting on "rm - rf on external_sd"
I would like to get on the developer board, to ask directly, how I could fix this.
regards
Phew!
hillbillie said:
Been up tonight on The Evervolv screen, rebooted, still Evervolv screen
Sounds similar to your problem, cannot get any PC link, power and volume controls gets me to fastboot but the PC does not see the device
Retry, Retry, EvervvolLLLLL screen, nothing else
Any suggestions or tips
thxs
---------- Post added at 05:29 AM ---------- Previous post was at 05:15 AM ----------
Managed to pull back TWRP screen, wiped Dalvik, cannot mount external_sd, now waiting on "rm - rf on external_sd"
I would like to get on the developer board, to ask directly, how I could fix this.
regards
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=25468368&postcount=5&nocache=1&z=8663575234822929
Sorry for the simple posting, but the above thread fixed the problem.
The original failure was caused by missing the factory reset after flashing, before unzipping.
Wow , XDA saved the tab for xmas, although the 2 steps flash cust and flash tombstones didn´t
work, it rebooted to an older version just fine!
Then restored backup, I´ll try again after xmas.
Happy Xmas !!
Hello Guys i had the problem that i couldnt mount date and i found in a forum post a "fix" the command mke2fs -T ext4 /dev/block/mmcblk0p8 i entered twrp got to advanced then to terminal and entered it after finsihing i reboot my devices it vibrated and shut off only a blackscreen and a short vibration. Can anyone help me? thx Also when i try to charge it it vibrates stop vibrates and so on..also happens when connected to the pc.