Hi
I'll put my G5 on charge and it will start to fast charge like normal then after a few minutes stop and go to just charging, if I pull the cable out the phone and plug it back in, it will usually still not fast charge sometimes it does first time tho but normally I'll have to do that 3 or 4 times to get it to fast charge again and usually it then fast charges normally till the battery if fully charged.
I thought it was the cable as it was on it way out it had a internal break where it would stop charging or go to normal charging at times so ordered a replacement cable same make (choetech 6ft) I've been using for over a year now and a juicebitz 9ft one and there both doing the same and I even tried the original cable and that's doing it too so it's not the cable.
I've cleaned the usb port no change, I've factory reset no change, can't remember when this first started as I thought it was the cable but I think it could of been around the time of the last update but can't be sure on that could of easily been just before.
What to try next could it be a charger fault, a faulty bottom module/ usb port, battery fault or a fault with the phone itself?
Any help would be appreciated.
I have same issue with my phone after last update.
That's good know not good that your having the same issue I mean good to know it's not a hardware problem.
I've seen a couple of posts after I starting this thread in the v20i update thread from users with the same problem so it looks like it's a software issue I can stop stressing about it as there's nothing I can do about it.
I did a search before posting and must of missed it or used the wrong terms in my search.
I just hope they will fix that in next update (oreo)
pazi79 said:
I just hope they will fix that in next update (oreo)
Click to expand...
Click to collapse
So do I it's part of what I hate about updates they fix things but just as often break something else.
same here. its turning to normal after minutes and when you plug it again its fast charging for a short time. LG g5 is a headace. My disappointment.
I have the exact same issue with my H-850 I even went to the extent of sending the phone in for repairs under the warranty. They replaced the mainboard and the bottom module but the problem still persists, its either the battery or software, my money is on the software
Related
Hi all,
I have an AT&T Samsung Galaxy S 2 (i777). It was rooted and running CM 10.1. A few months ago it started to have charging/USB port issues. Some of the symptoms:
-Sporadic charging (starting and stopping)
-Required USB jiggling to get it to start charging
-Sometimes wouldn't charge at all until it died, then would eventually charge while powered off
-Would not shutdown (only reboot, even if the battery was removed)
-Randomly started "car mode"
My initial thoughts on this were USB port issues. After doing some research on people with similar problems, I tried cleaning the port with alcohol, toothbrush, compressed air, etc. No avail.
Eventually the phone just stopped charging altogether. At this point, if I left it plugged in, it would sit in a continuous boot loop (boot, get to lock screen, realize it has no juice, shutdown, rinse, repeat). After a few days of attempting to charge and just having that happen, it went black and has never turned on since.
To try to solve that, I bought a new USB port flex cable on eBay and replaced it, assuming this would solve all my USB port issues. I tried to be as ESD safe as possible and also not break anything in the phone, but after replacing the board, it still wouldn't boot.
Next step- bought a new battery with an external charger to skip the USB port altogether and see if the battery was shot. Charged up the new battery, popped it in, nothing.
I'm at a total loss. If it started as a charging problem, I don't see how the problem could have been anywhere but the flex cable board or the battery. Does anyone have any ideas about what might be going wrong? I would REALLY appreciate some insight.
Thanks!
Maybe the repeated loops damage it
Sent from my GS4 running CM11 Kandy Kane
aptbosox said:
Hi all,
I have an AT&T Samsung Galaxy S 2 (i777). I
Eventually the phone just stopped charging altogether. At this point, if I left it plugged in, it would sit in a continuous boot loop (boot, get to lock screen, realize it has no juice, shutdown, rinse, repeat). After a few days of attempting to charge and just having that happen, it went black and has never turned on since.
To try to solve that, I bought a new USB port flex cable on eBay and replaced it, assuming this would solve all my USB port issues. I tried to be as ESD safe as possible and also not break anything in the phone, but after replacing the board, it still wouldn't boot.
Next step- bought a new battery with an external charger to skip the USB port altogether and see if the battery was shot. Charged up the new battery, popped it in, nothing.
I'm at a total loss. If it started as a charging problem, I don't see how the problem could have been anywhere but the flex cable board or the battery. Does anyone have any ideas about what might be going wrong? I would REALLY appreciate some insight.
Thanks!
Click to expand...
Click to collapse
Did you ever find a solution? I'm in the no charge boot loop after letting it die last night.
I have not seen previous usb problems at all. I suspect that my battery got over-drained, but then I've got the same symptoms as you and you have a new battery. I can get it into recovery but t won't stay on in CWM for long enough to fix permissions, which is the only thing I've tried so far in CWM.
Thanks
If i was in your place i'd have taken it to the nearest Samsung Service center and let them fix it for me.
I think the fluctuation in power may have damaged your phone battery point from where it takes power from the battery and charge it.
Maybe it has damaged the motherboard.
We cannot say anything in this situation.
You should just take it to your nearest service center.
Best of Luck
OK, wiping Data fixed it.
Thanks for your reply. This problem just started this morning with no previous issues, doing the looping part of your problem that I quoted. so it's not a question of what I might have done.
But, for others encountering my part of it, here's what I've done and learned so far today.
As I looked into things elsewhere on the , it seemed to be a software problem. Luckily, I have another Galaxy (Exhibit) that's similar battery and I was able to put the charged battery from it into the SII. The SII booted and worked fine but did not charge. I put the SII battery into the Exhibit (sorta fits). It took a charge.
This confirmed to me that it's not the battery. It must be the phone perhaps USB port or more likely "firmware" since problem started abruptly after draining battery down.
I then wiped data on the SII from CWM/recovery and rebooted.
SII is now charging again. Stock battery is back in and working.
Time will tell if all is well, but here's what I think happened:
1) battery drained down to zero while unplugged
2) plugging in and starting up phone immediately threw something off in the battery stats at a low level...that kept it from charging even when turned off. Or rather threw it into a loop. Don't really understand this stuff, but may have to do with physical things that happen in a battery when the cells drop down way low and then the voltage feedback they give to charging circuit.
3) charging battery in another device (gingerbread, by the way) got the battery out of this, if battery had been a contributing factor,(or just a trigger) it was back over the hump.
4) wiping data fixed the charging, so I conclude it was a charging circuit data issue triggered by an ultra low battery.
Hope I'm over this problem and hope that it helps somebody else. If you run into this yourself with no previous USB or hardware issues, I'd suspect software before hardware. If I had only one battery and no way to charge it externally, I would suggest get one of those simple universal clip-on chargers to bring the battery back up and then go into CWM and wipe data.
UPDATE: It's stopped charging again. It's no longer looping since I got the battery charged up, but not right either. As soon as I plug it into a USB, it boots itself without powering on.
I guess that this is looking more like a physical USB issue now. Weird that there's been no previous sign of trouble before today.
UPDATE2: I cleaned USB port but no help. Then I bent the USB contacts towards the screen and it is charging now again. I'm ordering a replacement USB.
I should add that I'm running Shostock Jellybean, older (not current) version with it's associated Jeboo kernel. Don't know if it matters.
I wish I'd seen your post sooner.. I had exactly the same problems back in January. Took all the same steps you did. In the end, an 8$ USB flex cable from EBay solved the problem. I think you'll have luck with that:thumbup:
Sent from my Slimbeaned Sgh-I777 (unbricked x4 )
hey, I'm experiencing the same issue slightly different.
-Sporadic charging (starting and stopping)
-Randomly started "car mode"
-plugged in the charger while the device is switched off, it automatically turns the device on.
-If the cable still plugged in while the charger removed from the main current, it shows "Charging stopped. High voltage"
-From yesterday, it doesn't charge even. Only way to charge is, connect the charger first and then Restart the device.
Then only charging continuous.
Can anyone help to solve this? Is this a software issue?
Thanks!
---------- Post added at 04:50 AM ---------- Previous post was at 04:46 AM ----------
Also, there was this issue early --> when I charge it from the laptop, the USB mode doesn't switch on. It just charge the phone only.
But now it's not even working like that.
Tweaker7376 said:
I wish I'd seen your post sooner.. I had exactly the same problems back in January. Took all the same steps you did. In the end, an 8$ USB flex cable from EBay solved the problem. I think you'll have luck with that:thumbup:
Sent from my Slimbeaned Sgh-I777 (unbricked x4 )
Click to expand...
Click to collapse
Which flex cable you bought exactly...plz give me the link...i badly need one...thx
mmystere68 said:
Which flex cable you bought exactly...plz give me the link...i badly need one...thx
Click to expand...
Click to collapse
Hey bro.. I've been offline forever.. Did you ever get what you needed?? I can pm you some info:good:
Tweaker7376 said:
Hey bro.. I've been offline forever.. Did you ever get what you needed?? I can pm you some info:good:
Click to expand...
Click to collapse
Tweaker7376 said:
I wish I'd seen your post sooner.. I had exactly the same problems back in January. Took all the same steps you did. In the end, an 8$ USB flex cable from EBay solved the problem. I think you'll have luck with that:thumbup:
Sent from my Slimbeaned Sgh-I777 (unbricked x4 )
Click to expand...
Click to collapse
hi, my s2 wont charge. It just shows up charging when plugged in but it doesnt charge at all. and it overheats too much while plugged in. What is that flex cable you said, is it the one that connects the charging port to the motherboard? were you the one opened and replaced it? thanks
Hey guys, it's been awhile since I asked a question, but here I am, lol.
In a nutshell, I'm pretty sure something in my device (hardware) is fried, but I thought I'd see if anyone knows better.
The problem is my device seems to be sending power out of the usb port, and doesn't connect to the pc or recognize it is charging correctly.
This also applies to download mode (windows says device has malfunctioned) and when powered off (there is no battery that shows up when plugged in). In order to power back on after turning it off, I have to remove the battery, then reinsert it while holding down the power. I can't think of much that could have caused this, other than I was visiting places with high humidity levels. One unusual thing that happened before this started was my device rebooted into safe mode when playing bad piggies. That was really weird since I have tried booting into safe mode before, but thought samsung must have disabled it for some reason. I have already tried wiping data and flashing a new kernel/rom. Obviously I can't re-partition since I can't connect to my computer in download mode. What do you guys think? I think it is time for a new device.
EDIT: I should mention that it started behaving normally yesterday for about 5 minutes, but then it went back to this.
iJimaniac said:
...
In a nutshell, I'm pretty sure something in my device (hardware) is fried, but I thought I'd see if anyone knows better.
The problem is my device seems to be sending power out of the usb port...
Click to expand...
Click to collapse
I'm 99.9% sure that under normal conditions that an Android device should never power the USB port. Source of speculation. If it is indeed powering the USB, then you've either got a really wonky firmware installed, or some sort of hardware issue. I'd try to make sure that it's sending power out before going further (especially if you can't charge it, the battery will be dead soon). After this test, I'd keep the battery out for a while, just to be sure it's not going to short anything.
One thing I've noticed in my tinkering is that taking a device apart, then putting it back together again can mysteriously fix problems (although 75% of the time the fix is temporary). If you suspect water damage, opening it up and letting it air out might help. I want to say there are certain cleaners that are great for cleaning up any water spots that might be shorting things out, but I've never had to try myself.
That's all I can think of right off. Good luck.
Dr. Cyanide said:
I'm 99.9% sure that under normal conditions that an Android device should never power the USB port. Source of speculation. If it is indeed powering the USB, then you've either got a really wonky firmware installed, or some sort of hardware issue. I'd try to make sure that it's sending power out before going further (especially if you can't charge it, the battery will be dead soon). After this test, I'd keep the battery out for a while, just to be sure it's not going to short anything.
One thing I've noticed in my tinkering is that taking a device apart, then putting it back together again can mysteriously fix problems (although 75% of the time the fix is temporary). If you suspect water damage, opening it up and letting it air out might help. I want to say there are certain cleaners that are great for cleaning up any water spots that might be shorting things out, but I've never had to try myself.
That's all I can think of right off. Good luck.
Click to expand...
Click to collapse
Yeah, I'm working on taking it apart right now. With my limited experience on electronics, I would be willing to bet it's a capacitor that's gone bad somewhere. That wouldn't be a problem on a desktop since I could just solder a new one in, but I don't think I have the skill to do something in such a small scale, not to mention I don't think you can even buy them that small.
The same thing happened to me, and I had to send it in for repair. Luckily, I was still in warranty. Also, are you sure it's not the charger cord?
TheKryptonite said:
The same thing happened to me, and I had to send it in for repair. Luckily, I was still in warranty. Also, are you sure it's not the charger cord?
Click to expand...
Click to collapse
I've tried multiple cables, and I'm unfortunately out of warranty.
Upon disassembling and cleaning with rubbing alcohol, it seemed to be working properly, with the exception of computer connection. However, I plugged it into a DC car charger (leaving the charger itself unplugged from an outlet), and the light came on again (which is what I was talking about when I said it was sending power out), and now it is acting weird again. I guess I'll take it apart and clean it again...
iJimaniac said:
I've tried multiple cables, and I'm unfortunately out of warranty.
Upon disassembling and cleaning with rubbing alcohol, it seemed to be working properly, with the exception of computer connection. However, I plugged it into a DC car charger (leaving the charger itself unplugged from an outlet), and the light came on again (which is what I was talking about when I said it was sending power out), and now it is acting weird again. I guess I'll take it apart and clean it again...
Click to expand...
Click to collapse
honestly, i cannot begin to fathom what could be causing this. it seems to me samsing paid more attention to the charging port then say amazon did on the first gen kindle.
i do however, wish you the best of luck and hope you somehow manage to fix it
iJimaniac said:
I've tried multiple cables, and I'm unfortunately out of warranty.
Upon disassembling and cleaning with rubbing alcohol, it seemed to be working properly, with the exception of computer connection. However, I plugged it into a DC car charger (leaving the charger itself unplugged from an outlet), and the light came on again (which is what I was talking about when I said it was sending power out), and now it is acting weird again. I guess I'll take it apart and clean it again...
Click to expand...
Click to collapse
See! Told you taking it apart and putting it back together again works... temporarily. :silly:
You're right, that does sound like power going out. Which would be super cool for powering, say, a micro USB laser pointer, but it's not so great when it should be charging. Can you double check with another device that the charger doesn't light up normally? I know my wife's laptop charger has a LED that stays on for a long time after it's been unplugged from the wall, sipping off of power left in the charger. It could be something similar with your charger.
Just a though... if power is only suppose to go into the device, then wouldn't it be reasonable to assume to that there would be a diode forcing power to only go one way? Or does it need to cycle power back to the charger? IDK, but it might be worth looking to see if something looks missing.
I read somewhere that if the battery voltage gets too low i.e. battery is totally flat, a current will flow from the device to the charger so this may be what's going on here. I didn't really understand the post as I was just whizzing through the thread, but i think the solution was to charge the device for many hours until the battery voltage was high enough for normal charging to occur. I'll try and locate the post, but it might take a while
Sent from my Nexus 7 using XDA Premium HD app
@iJimaniac if all of these suggestions dont work, there is the possibility to just buy another battery and a battery charger and keep switching out the batteries when they die
Maybe @henk5066 would know something about this?
From what it sounds like, your power circuit is fried and is not directing power correctly this means that you're probably going to have to replace the mainboard. however don't worry. you can get one from a player with a broken screen on ebay for about 10 $. I can p.m. you some links to products on eBay with main board working and not screen and I can post a video on YouTube that shows you how to replace the board. it's actually rather quite easy. I don't get why most people don't do that and instead buy a new one. let me know if that helps
Sent from my YP-G1 using xda app-developers app
henk5066 said:
From what it sounds like, your power circuit is fried and is not directing power correctly this means that you're probably going to have to replace the mainboard. however don't worry. you can get one from a player with a broken screen on ebay for about 10 $. I can p.m. you some links to products on eBay with main board working and not screen and I can post a video on YouTube that shows you how to replace the board. it's actually rather quite easy. I don't get why most people don't do that and instead buy a new one. let me know if that helps
Sent from my YP-G1 using xda app-developers app
Click to expand...
Click to collapse
Wow, I didn't realize a broken player is so cheap. I'll look into it, and instructions won't be needed; I've already fully dissasembled my device many times in the past, just for kicks.
Edit: could you send me those links? I'm having a hard time finding very many under $25, which is still a good price I suppose.
the broken player it's self is cheap (0.99$ if your lowest bidder and win) it is shipping that makes up for most of the cost. Just make sure you get one that says powers on, that is the main indicator that the main board is still good.
EDIT: I just looked on ebay, aparantly the person i bought my new board is out of the 4.0 player. and it looks like there is however one with a 9.99$ bid. you could raise it and get the player but that is the cheapest you will get. i will pm you a link to it.
I had the same problem
I had the same problem, what i did was, instead of charging it with the original charger, i charged it with my nexus 10 charger in download mode all through the night, and the next day it would have about 80 percent charge and it was in the system, but it drained quick when i would unplugged it, so i repeat the same procedure over several days until get to 100% and scince then i have had no problems with my SGP, hopefully i helped you
Hell.Knight said:
I had the same problem, what i did was, instead of charging it with the original charger, i charged it with my nexus 10 charger in download mode all through the night, and the next day it would have about 80 percent charge and it was in the system, but it drained quick when i would unplugged it, so i repeat the same procedure over several days until get to 100% and scince then i have had no problems with my SGP, hopefully i helped you
Click to expand...
Click to collapse
Interesting, i thought the devices could not charge in download mode.
On the subject of odd charging behavieor, has anyone noticed that when plugged in running cyanogenmod overclocked to 1200mhz, the micro usb port area on the player gets rather hot?
henk5066 said:
Interesting, i thought the devices could not charge in download mode.
On the subject of odd charging behavieor, has anyone noticed that when plugged in running cyanogenmod overclocked to 1200mhz, the micro usb port area on the player gets rather hot?
Click to expand...
Click to collapse
I haven't noticed excessive heat in that area.
Sent from my YP-G1 using Tapatalk 4 Beta
Hi XDA,
My Galaxy S3 stopped charging properly a couple of days ago. In a matter of hours it froze and charged a bit slower, then it wouldn't charge anymore. When the phone is off and I plug in the charger, the animation starts for about 1 - 2 seconds, and then the screen goes black. If it's on, nothing happens when i plug the charger in and out.
I've owned the phone for a year, and I rooted about 3 weeks ago, and installed CM10.1 (Nightly). It worked fine until this problem.
I've troubleshooted a bit on my own, and what I've found out is that, it can't be the battery that's the problem, because I've tried three different ones, and the problem stays the same. It can't be the USB port on the phone, since I can get it to work in Download mode (ODIN mode). I've also tried CM9 and flashing back to stock android. I've also tried charging it from the wall and the computer, and used different cables. Nothing has done any better.
I'm guessing it's software related, I just can't figure out how to fix it.
Thanks in advance,
Zhibbhi
the charging port of the phone might be faulty.
SRIRAM
Sent from GALAXY S3 I9300 running PARANOID ANDROID 3+
By charging port I would suggest the charging circuit inside the phone is faulty, as it sounds like you've eliminated all the other possibilities. Return the phone to fully stock for warranty repair.
So even if I can access the phone through ODIN, the charging circuit can be faulty?
I just thought it was a strange coincident that it went faulty a just a couple of weeks after I installed CM10.1
Zhibbhi said:
So even if I can access the phone through ODIN, the charging circuit can be faulty?
Click to expand...
Click to collapse
yes
Zhibbhi said:
So even if I can access the phone through ODIN, the charging circuit can be faulty?
I just thought it was a strange coincident that it went faulty a just a couple of weeks after I installed CM10.1
Click to expand...
Click to collapse
Odin has nothing to do with the charging circuit .
Solutions .
One the battery try another
Two the charger try another >> charge phone from PC usb .
Three the cable try another
Four the USB port on the phone >>> clean
Five the onboard charging circuit >>> needs a service centre .
Six and highly unlikely a firmware problem wipe phone flash stock rom .
jje
Ok, thanks a ton guys! I'm going to set the phone back to stock, and send it in for warranty repair as I've tried everything else.
Zhibbhi said:
Ok, thanks a ton guys! I'm going to set the phone back to stock, and send it in for warranty repair as I've tried everything else.
Click to expand...
Click to collapse
In the future, avoid using S3's stock charging cable. I changed mine to one I bought off eBay and had no probs since then. I had several frequent problems like slow charging/no charging etc.
bjmath said:
In the future, avoid using S3's stock charging cable. I changed mine to one I bought off eBay and had no probs since then. I had several frequent problems like slow charging/no charging etc.
Click to expand...
Click to collapse
Best avoid using the phone to charge the battery at all, that way you don't stress the phone components with wake lock and heat. Buy a £6 desk charger and spare battery, replacing these is much cheaper than the phone motherboard.
Solved
I have an S3 and lately it has taken longer to charge and it was charging to less percentage. I tried 2 different chargers and 3 different cables with the same outcome. I was thinking about one of the threads I had read and they mentioned going to the cell store and it charged for them. I've read about it being the charge circuit on the main board and various other problems and solutions that didn't work. I went to Staples today and purchased a SCOSCHE reVOLT line h1 2.1 amp quick charge and in less than an hour I charged from 63% to the 100% I haven't seen in quite a while. The Samsung OEM charger it seems (as well as the other one I tried) had lost some of it's get up and go. It is working fine now and with this charger it doesn't take long at all to reach full charge. I've put a lot of time into customizing this phone after root and would have been VERY disappointed if I had to start over with a new one. I'd be willing to bet at least 90% of the charging problems people are posting about are caused by the charger deteriorating over time.
Shannon
Hello,
I have Galaxy S2 and having some charging issue. Yesterday, when I plugged it in the wall charger, it didn't get charged (i.e. even the flash on battery was not coming up) and when I tried to restart the phone, it powered off but didn't switch on. I tried holding the power button to turn it on but it didn't. So, I pulled out the battery and left the cell for some time like 20 mins or so. After re-inserting the battery, it turned on but still was not getting charged. I tried to change the USB cable as well but nothing helped. I then tried to charge it via my Laptop it actually started the charging process but with error on Laptop saying "USB Device not recognized".
Today, I tried the wall charger again and here's I found something: when my phone is ON and I plug it in the wall charger it doesn't charge but as soon as I turn the phone OFF, my phone starts getting charged (Battery image comes on screen which usually comes when the phone is off). So, that's how I am charging my phone.
I went to the repair shop today, he said it's a charging port issue on which I have some doubts that why it is even charging in this way if it's a port issue. I just want to make sure if whatever he's saying can be somewhat true.
Can you please help me out? I would be really thankful to you.
I look forward to hearing from you soon!
Thank you!
PS: I tried to search about the port issues but I couldn't find anyone having this kind of issue so please!
The issues you have mentioned really do all point to a faulty USB board......it is common (with a faulty board) for some functionality to work while other functionality is lost. The part itself costs pocket change and is reasonably easy to DIY replace......
If you want to go down that path, check my profile for threads I've started.....you'll find a guide explaining exactly how to do it.
Just make sure to read and note the section on 'rev versions' it is VERY important to get the correct one......
My wife says I'm a phone geek....She's probably right
I have noticed that fast Charging does not always happen even with the stock charger. However, if I reboot then fast charging kicks in. Is this a known issue?
No, I always have fast charging. Maybe you need to return your tab for warranty.
Techvir said:
I have noticed that fast Charging does not always happen even with the stock charger. However, if I reboot then fast charging kicks in. Is this a known issue?
Click to expand...
Click to collapse
I have this problem as a result of getting something in the charging port, or inside the USBC cable itself. All resulting in a moisture detected error. Powering down the tablet, plugging it in and allowing the charge indicator to come on would resolve the issue, but every time I unplug the tablet I would get the error again. I followed instructions on XDA regarding USB C fast charging problems and it seemed to fix the error. I think there's still something in the cable itself because the whole problem has expressed twice now. But in the interim comma over a few days if I plug the charger in one way I would get a slow charge warning that I wasn't using the original charger. But it's the charger that came in the Box. If I unplugged it, turned the charger around and plugged it in the other way it would fast charge again. So I'm guessing there's some kind of material in the charger itself that I can't get to that's affecting how many contacts are being made. I'm still working to resolve the issue with the original charger, but I'm thinking about just getting another USB C cable. I need a longer one than ships with the tablet in the first place.
When I went to chat with customer service, they wanted me to send it in under warranty. But I really didn't want to do without the tablet for 2 weeks or more, so researching it online has solved the issue somewhat. I might take it in to a Samsung kiosk and just see if they'll try to fix it with air duster.