Lenovo Z90-7 Hard Bricked - Android Q&A, Help & Troubleshooting

Hi,
I have a lenovo Z90-7 and I tried to flash Android 6 custom ROM , When flashing completed My device turned off then I turn it on and Lenovo logo appeared then it vibrated and the port on PC shown HS-USB 9006 and many partitions , nothing work when I power it on it vibrated only , I need HS-USB 9008 to flash another ROM , how to solve this problem ? I tried many tutorials on web but never work?

phoneix2017 said:
Hi,
I have a lenovo Z90-7 and I tried to flash Android 6 custom ROM , When flashing completed My device turned off then I turn it on and Lenovo logo appeared then it vibrated and the port on PC shown HS-USB 9006 and many partitions , nothing work when I power it on it vibrated only , I need HS-USB 9008 to flash another ROM , how to solve this problem ? I tried many tutorials on web but never work?
Click to expand...
Click to collapse
Download your stock rom and tool studio emmc tool from below link and flash your android.
http://www.aryk.tech/2016/12/toolst...-helps-you.html?showComment=1498419619573&m=1

Related

[Q] [Help] Lenovo K910 DualSim no download mode (brick)

Hello i have bricked my k910.
i flashed a new firmware with twrp and while flashing phone restart.
now im stuck on lenovo logo..
fastboot detect the phone but locked bootloader.
I test with qpst but Qualcomm HS-USB QDLoader 9008 is loaded 2-3 seconds and then the phone goes back to fastboot mode.
no blue LED.
now i disconnect the battery from the phone and only connect with usb+ "volume +, same problem... only detect the Qualcomm HS-USB QDLoader 9008 for few seconds.
what can i do now?
i tested already to click fast as possible to download in emmc software.. dont work.
i flashed before it brick twrp
and the system folder is empty :cyclops:
what can i do now?
gekkorist said:
Hello i have bricked my k910.
i flashed a new firmware with twrp and while flashing phone restart.
now im stuck on lenovo logo..
fastboot detect the phone but locked bootloader.
I test with qpst but Qualcomm HS-USB QDLoader 9008 is loaded 2-3 seconds and then the phone goes back to fastboot mode.
no blue LED.
now i disconnect the battery from the phone and only connect with usb+ "volume +, same problem... only detect the Qualcomm HS-USB QDLoader 9008 for few seconds.
what can i do now?
i tested already to click fast as possible to download in emmc software.. dont work.
i flashed before it brick twrp
and the system folder is empty :cyclops:
what can i do now?
Click to expand...
Click to collapse
did you see my solution for the COM/USB port problem here?
Unfortunately i'm facing a bigger isue atm :crying:
Crowds said:
did you see my solution for the COM/USB port problem here?
Unfortunately i'm facing a bigger isue atm :crying:
Click to expand...
Click to collapse
Hey, test with USB Extansion but dont work... or is 1 Meter to short?
gekkorist said:
Hey, test with USB Extansion but dont work... or is 1 Meter to short?
Click to expand...
Click to collapse
humm...not sure, mine has 4mts and it worked on 1st try
usefull tool in one place
Feel free to link your ideas :good:
http://forum.xda-developers.com/and...-tools-one-t2887839/post55673946#post55673946
Thank you
Crowds
i have the same issue, do you have a solution??
i try using a usb expansion of 10 Mts and i have the same issue, not boot no nothing.
luis0n said:
i have the same issue, do you have a solution??
i try using a usb expansion of 10 Mts and i have the same issue, not boot no nothing.
Click to expand...
Click to collapse
Sorry but that's the only solution. The one I've wrote on xda.
In fact its quite easy, the problem is when we ended up without it we stressed
For the first time it took me 1 month but then, after that experience, I've manage to make it work after 5 min. And believe me, since the first time, I've broken mine more than 20 times
Sent from my Lenovo K910 using Tapatalk
gekkorist said:
Hello i have bricked my k910.
i flashed a new firmware with twrp and while flashing phone restart.
now im stuck on lenovo logo..
fastboot detect the phone but locked bootloader.
I test with qpst but Qualcomm HS-USB QDLoader 9008 is loaded 2-3 seconds and then the phone goes back to fastboot mode.
no blue LED.
now i disconnect the battery from the phone and only connect with usb+ "volume +, same problem... only detect the Qualcomm HS-USB QDLoader 9008 for few seconds.
what can i do now?
i tested already to click fast as possible to download in emmc software.. dont work.
i flashed before it brick twrp
and the system folder is empty :cyclops:
what can i do now?
Click to expand...
Click to collapse
hi ,
I have a same problem . I can't activate download mode . It works 2-3 seconds and then the phone goes back to fastboot mode.
Did you find a solution ?
luboii said:
hi ,
I have a same problem . I can't activate download mode . It works 2-3 seconds and then the phone goes back to fastboot mode.
Did you find a solution ?
Click to expand...
Click to collapse
Hi,
no, have no solution. I try all tutorials and usw all Tricks i found in the Internet. Opst, miflash, nothing work. The 2-3 secs in donwloadmoade without a blue led is to short.
I try the tutorials on 6 different computers. Nothing.
I contact the Lenovo support in germany, usa and china, no help..
I found 2 services to unbrick the k910 with a own jtag
1 in Malaysia and 1 in romainia. But i dont trust this peoples.
I buy a new phone and put the k910 in a corner.
Sorry.
Lenovo phone... Never again
any news guy? had same problem with mine. already buy a new battery btw. sighh! when using miflash my phone didt disconnected from download mode but ended with error, while using qpst it keep connect then few second disconnected till my pc get bsod.
Send my phone I offer repair brick k910

[Q] k920 bricked blue light only help please!

Hello i have a huge problem with my k920 no boot no screen only blue led light when i connect the usb.In device manager is found as qualcomm hs-usb diagnostics 9006 (com13) everytime i connect it so is not discovered by emmc software.Is there any way i can fix it?bring it back to get the windows recognise it as hs-usb qdloader 9008 so i can flash new rom?
soulfreem said:
Hello i have a huge problem with my k920 no boot no screen only blue led light when i connect the usb.In device manager is found as qualcomm hs-usb diagnostics 9006 (com13) everytime i connect it so is not discovered by emmc software.Is there any way i can fix it?bring it back to get the windows recognise it as hs-usb qdloader 9008 so i can flash new rom?
Click to expand...
Click to collapse
Did you solve this problem? I have the same
Enter EDL Mode With K920
For Entering in EDL (Emergency Download Mode) In K920 ,
First try turn off your phone completely
then press Volume + and open your QFIL Program and connect usb cable to this (in this mode recognize as 9008 mode)
then you can flash it
but i flashed all rom that i know and still errors continues,
anyone know how can i Format my phone (Brush it from all previous things install on phones) ?
Enter testing, factory mode, power button+volume down. Wipe data, erase sd card, factory reset.
Same problem here.. Tried to flash with wrong model TWRP
Not only Blue light
K920

Bricked After Flashing Similar Device's ROM.

Hello once again,
Today I went on to flash a Redmi 3S ROM on a Redmi 4 Prada, which have similar hardware.
I replaced the boot.img in the original ROM zip, modified the build.prop a bit, and flashed
Now the Redmi 4 won't boot to recovery or bootloader...
Furthermore, if I press the power button for a while, the device will turn on and immediately off
What should I do?
A detailed guide would help me, because I never found one detailed enough while working with device manager and stuff...
EDIT: I can't get it into fastboot and device manager shows "qualcomm hs-usb diagnostics 900e"
Solved. I used a deep flash cable (with black and white wires) and on device manager the device turned to "Qualcomm HS-USB QDLoader 9008"
After that, I was able to flash an official dev ROM using MiFlash

Help unbricking Lenovo Tab 4 10 TB-X304F

Hi. I have a Lenovo TB-X304F that I unlocked and flashed successfully with TWRP, but I screwed up and then managed to brick the device. It now goes to black screen after showing the Lenovo boot image briefly. However I can still access Fastboot and Recovery.
I did backup Boot, Data and System before all this and I have restored these succesfully via TWRP, but the device still won't boot and is stuck on the black screen.
I want to flash stock rom again, and I have downloaded "Lenovo Tab4 A10-TB-X304F_S000038_170703_ROW_QFIL" which is available from some websites, and this is meant to be flashed with QFIL. The problem is that when connecting the tablet, QFIL is always stuck with port "Qualcomm HS-USB Diagnostics 900E (COM21)" which results in the error "Download fail:Switch to EDL fail Failed to switch to Emergency Download mode" when I try to download the firmware. It seems some have solved this issue by modifying a USB cable, but I'm unsure if this would actually help me.
Can anyone help me resolve this, please? Could it be possible to get a TB-X304F backup that perhaps works, when for some reason my backup doesn't? Does somebody have a stock rom that can be flashed using ADB or TWRP?
Very grateful for any help with this. Thanks.
Try using MiFlash not Qfil to flash stock
https://www.xiaomiflash.com/
rhaavin said:
Try using MiFlash not Qfil to flash stock
https://www.xiaomiflash.com/
Click to expand...
Click to collapse
Thanks a lot for your reply! Do you think MiFlash can flash the file that I mentioned above, though (Lenovo Tab4 A10-TB-X304F_S000038_170703_ROW_QFIL)? I believe I was trying out MiFlash as well but it seems it requires another type of file to flash?
deleted
unbrick "dead" tablet Lenovo TB 4 10.1 (X304F/L)
I managed to identify the test point on the motherboard. This allows the tablet to switch from Qualcomm HS-USB Diagnostics 900E driver mode to Qualcom HS-USB QDLoader 9008 mode. My tablet could not be booted into bootloader, recovery or system...
forum.xda-developers.com

Help!! red light on phone

i wanted flash my phone so i follow this guild on youtube.
/watch?v=naQX9Was6DY
after flashing it got red light. it was fine before. i try the vol down +power and volume up and down + power but nothing works.
the computer recognize it as "Qualcomm HS-USB Diagnostics 900E"
i manage to get it to display " Qualcomm HS-USB QDLoader 9008" but dont know how to proceed from here.
Specs Before Dead:
Miui 7.012
Android 5.6
32 Gb Rom,3 Gb Ram (kenzo)
update:
i end up fixing my phone. it was in EDL Mode. i had Flash Using DFC Cable or Xiaomi EDL Cable. i made one from an youtube video ( it was one with button i made, it allow to get get QDLoader 9008 with consistency and without removing the back cover.)
afterthat i just flash it miflash tool with "kenzo_global_images_8.11.22_20181122.0000.00_6.0_global " it had to be DEVELOPER VERSION thought. i dont know if i can do it a second time because it might be a flute that it was able to flash at all LOL. and this is the only phone i have and i dont want to use an Iphone7. one thing i dont like is it wont let me flash twrp or OrangeFox- ( it said it can not found file flash_all.bat) cause when went push vol up + power it just give me standard xiami menu.
when i have a compatible phone on the same cell network, i'll try to flashing a diff rom cause the xiami rom has lots of ads. .
Bluesaky said:
i wanted flash my phone so i follow this guild on youtube.
/watch?v=naQX9Was6DY
after flashing it got red light. it was fine before. i try the vol down +power and volume up and down + power but nothing works.
the computer recognize it as "Qualcomm HS-USB Diagnostics 900E"
i manage to get it to display " Qualcomm HS-USB QDLoader 9008" but dont know how to proceed from here.
Specs Before Dead:
Miui 7.012
Android 5.6
32 Gb Rom,3 Gb Ram (kenzo)
please help
Click to expand...
Click to collapse
I think you have locked your bootloader. Well if that is the case try flashing TWRP again it will solve your problem.
Refer to this tutorial https://www.youtube.com/watch?v=xExKvog5RP4
LoadOP2 said:
I think you have locked your bootloader. Well if that is the case try flashing TWRP again it will solve your problem.
Refer to this tutorial watch?v=xExKvog5RP4[/url]
Click to expand...
Click to collapse
from you tube
tried it, didnt work. it said flash success. but the phone will not power on. VOL up +power not working, vol down + power not working either
Bluesaky said:
i wanted flash my phone so i follow this guild on youtube.
/watch?v=naQX9Was6DY
after flashing it got red light. it was fine before. i try the vol down +power and volume up and down + power but nothing works.
the computer recognize it as "Qualcomm HS-USB Diagnostics 900E"
i manage to get it to display " Qualcomm HS-USB QDLoader 9008" but dont know how to proceed from here.
Specs Before Dead:
Miui 7.012
Android 5.6
32 Gb Rom,3 Gb Ram (kenzo)
please help
Click to expand...
Click to collapse
Are you able to boot your device into EDL mode? If not, try to boot into EDL using the test point method if default method doesn't work. If you're successful in booting up in EDL, Follow the below forum to recover the bootloader and recovery.
Link to the test point method tutorial: https://www.youtube.com/watch?v=_jv1ZVQ95Ng
Follow this after you enter the EDL mode successfully: https://forum.xda-developers.com/redmi-note-3/how-to/unlock-unofficially-install-zcx-twrp-t3586778

Categories

Resources