Hi
Actually, I have a redemi note 4x device. last week unfortunately I flashed a wrong Rom on my phone and it became brick
I can not turn it on and it does not go to recovery mode or fastboot mode or anything
I understood that I need to flash the Rom with deep flash cable
I ordered deep flash cable and followed instructions but my laptop does not recognize Qualcomm driver
I press the bottom on the cable and then connect the phone but it does not recognize it
it is really annoying that I can not do anything for it
I have heard redemi note 4x does not go to EDL mode with this cable is that true?
Has anyone any solution?
Ps: I opened the back of the of the phone even tried to use 2 points to jumper but it did not work really so I ordered the cable but it seems the cable is also not working
I appreciate if anyone knows a way regarding this problem
Thanks and Regards
flash firmware then rom
Related
My redmi note 3 is ordered from china (offical of course),i was using it in china stable rom , i try to falsh it, i failed so many time, cause of having bootloader. Finally, there is some way to unlock bootloader, so i try to do it, and i was sucess to falsh to global stable rom with edl mode , after that, it was all okay but one day ,i shut the phone down cause of lagging. and straight use a cable to charge it , and straight go into the edl mode for no reason ( i think i forget to close oemunlock, usb debugging or something else), so i was not worry at all, i thought i can flash it , but when i plug the cable with my phone into my laptop, and i open my MI FLash , i was SHOCKED that MI falsh is not showing up from my laptop, After that i try so many solution i even open the case and unplug battery and usb cable, and it boot into the edl mode also , i have many phone like this same solution like about 6 ( ShopHire)
somettime show this and so many customer has return and i am worry about it , another solution there is 4 of the phone boot into edl mode after i insert the cable, BUT its cause of other reason, when i falsh Its failed on mi FLash and this show up ( Reached the limit of the file exceed 256 ) something like this , i just hope u guys can help me , i was i big problem. PLs help Thanks.
stupid red blinking have to option:
1. red blinking means you are in EDL mode.
2. red blinking meand your battery have not enough charge to turn your phone on.
so you may have ran out of charge. or charger adapter or cable problem.
Hi,
I got my new phone a couple of days back, installed CM13 (officially unlocked, did that with TWRP + install ROM) probably incorrectly because i couldn't get the fingerprint sensor and other stuff to work at all.
Today my phone turned off by itself with around 70% of battery left and it's not responding anymore. Cannot go into Recovery mode, not even to Fastboot. Connected it to the charger and have the red light of the devil blinking... Tried to do everything i found online but i couldn't get into EDL mode (and then Flash through MiFlash), since fastboot is not working at all.
I really don't wanna have to open the back of the phone and. What can i do to save the phone? Is there any proven solution and a comprehensive guide to this (for a total idiot like me)?
Yes there is deep flash cable method search on xda/youtube it works like a charm,😉, this method saved me once
Try this (http://forum.xda-developers.com/redmi-note-3/how-to/guide-how-to-flash-hard-bricked-redmi-t3490055) works 100%
Try to disconnect and reconnect the battery.
This has kicked me into EDL mode once and after flashing it was fine
Both methods are sound, but if you decide to remove the back cover, remember to eject the SIM card tray first
Thanks for the replies, i was hoping i wouldn't have to have to open the back cover and disconnect the battery but it seems to be the only option at this point.
The deep flash cable doesn't seem that difficult tho, why don't you give it a shot? It seems like that's what they use at MI service centres after all.
So i have managed successfully to have the pc recognise the device as Qualcomm Hs USB Qdloader 9008, opened the MiFlash tool and recognised the device, but when i try to flash a stable MIUI rom i get an error: "Write timed out" as many times i tried to do it.
Does anybody have a suggestion?
My device was unlocked officially and i have no recovery no fastboot nothing at all.
alphax_ said:
So i have managed successfully to have the pc recognise the device as Qualcomm Hs USB Qdloader 9008, opened the MiFlash tool and recognised the device,
Click to expand...
Click to collapse
Which method you used - Deep Flash cable or Battery disconnect?
Yeah sorry i did not mention it, disconnected the battery.
i tried the battery removing method but the phone is not responding
now need to try cable method
Ryan Raghendh said:
i tried the battery removing method but the phone is not responding
now need to try cable method
Click to expand...
Click to collapse
Get into EDL
HELLO I was trying to unlock my bootloader by flashing a zip file with mi flash in EDL MODE the result was the device is now bricked it only flashes red led no power on no recognition by computer bootloader locked no fastboot no adb
people suggested something called a deep flash cable to connect straight to the CPU Qualcomm port 9008 now the computer recognize the phone but when I try to flash a ROM it gives cannot receive hello packet error
is there any hope left?:crying:
redmi note 3 pro snapdragon
Only Service center ATM.
aliamiri70007 said:
HELLO I was trying to unlock my bootloader by flashing a zip file with mi flash in EDL MODE the result was the device is now bricked it only flashes red led no power on no recognition by computer bootloader locked no fastboot no adb
people suggested something called a deep flash cable to connect straight to the CPU Qualcomm port 9008 now the computer recognize the phone but when I try to flash a ROM it gives cannot receive hello packet error
is there any hope left?:crying:
redmi note 3 pro snapdragon
Click to expand...
Click to collapse
deep flash cable problem.it should show Qualcomm qdloader 9008 or something.
use testpoint method. i did it once by my self with just a screwdriver and forceps
I connect the phone to PC it shows up as Qualcomm 9008
And flash tool shows as com20 but there is no flash button
We're is the flash button?
aliamiri70007 said:
HELLO I was trying to unlock my bootloader by flashing a zip file with mi flash in EDL MODE the result was the device is now bricked it only flashes red led no power on no recognition by computer bootloader locked no fastboot no adb
people suggested something called a deep flash cable to connect straight to the CPU Qualcomm port 9008 now the computer recognize the phone but when I try to flash a ROM it gives cannot receive hello packet error
is there any hope left?:crying:
redmi note 3 pro snapdragon
Click to expand...
Click to collapse
if deep flash mated ( with deep flash cable) not work for you:
open your phone and disconnect your battery and flash your phone
Please help there is no flash button on flash tool even though the computer says the phone is connected Qualcomm 9008
If red notification light flashes, then you are already in EDL mode, and deep flash cable is nothing but the usb cable which has circuit breaker(switch) between green and white cable... jus buy a cheap data cable from market and peel it partially... now peel the green and white wire... ur deep flash cable is ready.. now insert the cable in pc and phone.. and join the green wire and white wire for 8 seconds... you are in EDL mode.
Hey bro i had faced the same issue that u are on. I had lost hope, but there is solution. There is a video on YouTube -
. This you can watch.
Now the procedure is very simple.
1. Remove the backpanel of your phone( don't worry nothing that serious)but do it carefully as the fingerprint wire is connected already so u should not tear it. Remove the fingerprint cable. Then remove the battery's frap type cable and reinsert it and reinsert the fingerpint one and close the panel. Similar to removing the battery and inserting it again.
2. According to that video, take the copper wire and insert it on the middle pins, very very carefully and insert it in the usb port of your computer. Mind it it might not work at the very first try, due to not applying the wire correctly but for sure it works, so take a small wire and not a bunch of wires and connect it with the port connected to your phone.
3. After inserting let your computer detect it and then remove the Usb cable. Remove the wire. And insert the cable again without wire. Now the port is unlocked and you can easily flash stock os through Mi flash application on pc.
It is super simple and don't panic. Hope you get your phone recovered???.
Don't work it can be fixed,dm me if you haven't already
Hello Guys,
I would like to flash a Redmi Note 3 pro with twrp.
The problem is it is not recognized by PC. It's not even showing anything in device Manager.
I installed usb drivers from Xiaomi, I booted to Fastboot Mode and connected the Phone to the PC. Nothing is happening. No device ist showing in device Manager.
I tried 3 different USB cables and also to connect it to a notebook instead using my PC. No Chance.
Then I tried to connect a Redmi Note 4X in Fastboot mode and the same happened. IT IS Not recognized and the device manager don't show a new device.
Both phones are officialy unlocked.
Anyone who faced the same problem and can help
Joe886 said:
Hello Guys,
I would like to flash a Redmi Note 3 pro with twrp. The problem is it is not recognized by PC. It's not even showing anything in device Manager. I installed usb drivers from Xiaomi, I booted to Fastboot Mode and connected the Phone to the PC. Nothing is happening. No device ist showing in device Manager. I tried 3 different USB cables and also to connect it to a notebook instead using my PC. No Chance. Then I tried to connect a Redmi Note 4X in Fastboot mode and the same happened. IT IS Not recognized and the device manager don't show a new device. Both phones are officialy unlocked. Anyone who faced the same problem and can help
Click to expand...
Click to collapse
Hi, so you have tried 2 PCs, 2 phones and 3 cables. I think you missed it in the Device Manager. Please connect your RN3P phone in fastboot mode and run http://www.uwe-sieber.de/usbtreeview_e.html then do File/Save full report, and post it here. Alternatively, run any live Linux and post lsusb output.
Thank you for your reply.
As it seems I can´t post links because i`m new and when I try to post the report here it says I can`t because it has more than 30000 caracters
But as I said it won´t be recognized. Both of them won`t.
When I connect them in working mode I can´t even access the data like pictures etc.
One of the 3 usb-cables were originaly packaged as I at first suspected the usb cables were faulty.
But now a friend of mine come by and I tested to connect his Redmi note 4x and it is working. The only difference is that he has miui 8 and I have miui 9 from xiaomi.eu.
So I am out of ideas now. The only I can imagine is that both usb ports on the smartphone are ****ed and therfore it won´t connect properly.
Charging is no problem by the way
Bro you have to setup adb drivers perfectly a single error in setting up leads error but no worry it would not harm your device....
So first of all setup adb driver from the given link it will show you how to setup adb driver
Then go your processor of setting up twrp.
If you need any help on setting up twrp just reply on it....
Hey, I need Some help ASAP, I am in a Big trouble. So The whole scenario is that I decided to install the Paranoid Android 11 in my Mi A3 and After Unlocking the Bootloader, I changed the Boot Slot from A to B and Flashed the Twrp file ( to the boot ) and Pressed the Power and Volume down Button, The Phone turned off and is not turning on Not Even the Fastboot Logo, Its Bricked. (Here are some additional Points Which you Should Know, 1. I checked the ports on my Computer and It was Showing Qualcomm HS-USB QDLoader 9008 So I think the phone is in EDL mode. 2. I tried to Flash Mi A3 Stock Firmware using Miflash and It was Showing Error "Cannot receive hello Packet") The Phone is my Daily Driver and If anyone can, Please help me Fix this.
Even I got the same issue after downloading the latest Android 11, then got rectified the Mobile through the nearest service center.
Globally many people experienced the same issue.
Now it is ok !
use qfile and service rom
set up in ufs mod
plug off battery and connct usb with short test point
load files 0/1/2/3/4/5 and
elprfesor said:
use qfile and service rom
set up in ufs mod
plug off battery and connct usb with short test point
load files 0/1/2/3/4/5 and
Click to expand...
Click to collapse
could you explain it more?
I also dead briked my phone after install a11 and used qfil to flash some stuff in edl mode using test points,
I recommend using the right qualcomm driver 32 or 64 bits like your OS and also reboot after install driver,
I don't recommend open the back painel bcs even u doing it right it don't close well after bcs lose stickiness,
If u can just go to a service, they can manage with this better then u.
Same here. Even opened the back cover to touch the EDL points.
Tried getting out of that mode by flashing to stock ROM using the Mi Flash Tool as I'm getting a weird error, `Input string was not in the correct format`. even when using the very same input as I've seen on a YouTube Tutorial & I had also tried it out on the very same version of Flash Tool (and still got the error)