Related
Hi everyone, this is my 2nd post on the forum because it is very urgent. When i press the power button and my phone goes into sleep i notice after about 5-20 minutes the screen blinks and everytime it blinks and i wake the phone and try to turn on my wifi it shows up with wifi "error" . i am looking for a permanent solution.
What i tried :
1) restarting phone (works short term)
2) typing *#*#526#*#* in keypad (works short term)
3) Wifi policy set to "never" (had no effect)
4) FXR WIFI FIXER app (had no effect)
5) battery pull (no effect)
6) static ip (no effect)
7) factory reset/ new rom (no effect)
So can anyone help me with this It started when i was using kph 2.3.4 and now i use kpe 2.3.3.
Please reply any help would be appreciated
what rom are you using? rooted or no?
if possible go to cwm / or stock revoery
enter by shutting down phone
- then press power and middle button together for about 20seconds(?)
-press down button to format
-press middle
-wait
-done
-your phone is formatted and fixed hopefully
I already said!
tohno said:
what rom are you using? rooted or no?
if possible go to cwm / or stock revoery
enter by shutting down phone
- then press power and middle button together for about 20seconds(?)
-press down button to format
-press middle
-wait
-done
-your phone is formatted and fixed hopefully
Click to expand...
Click to collapse
i already said i tried factory reset and i said that i was using 2.3.3 kpe.. Thanks for the reply though any help?
Thepizzaguy97 said:
i already said i tried factory reset and i said that i was using 2.3.3 kpe.. Thanks for the reply though any help?
Click to expand...
Click to collapse
Try reflashing with odin.
If it doesn't work, well service center is your only solution.
TeamCooper Developer
I had the same problem about wifi error... I would use that code
Agreed short term success
But then I flashed a cm7 ROM and it works like a charm
-------------
May The Force Be With You
jumbobombo said:
I had the same problem about wifi error... I would use that code
Agreed short term success
But then I flashed a cm7 ROM and it works like a charm
-------------
May The Force Be With You
Click to expand...
Click to collapse
Thanks for the reply, btw how is the camera quality on cm7?
Thanks!
Thepizzaguy97 said:
Thanks for the reply, btw how is the camera quality on cm7?
Thanks!
Click to expand...
Click to collapse
Camera quality is good in Cm7..
Don't just say thanx click on the thanx button
Cameras good same as the stock
Modding the phone doesn't change its hardware
-------------
May The Force Be With You
Lol , thanx is my signature and I will click thanks
Thanks!
i am having a problem with my samsung galaxy s2, the power menu doesnt come up when i press the shut down button but it switches off straight away, and the lock screen doesnt work, non of them does. i would be so grate full for who ever can find me a solution
Backup data and factory reset first .
jje
i would have said the same as jje said..
It happens exactly the same
my sgs2 doesn´t block the screen and when I hold the power button it turns off directly, I just Installed ICS and does not work either unlock pattern or pin just turn off the screen and when i push the home button or the porwer button just turn on, does not show any unlock screen, i´ve already done the factory reset and wiped cache and still the same, it´s the same problem i hope that anyone can help us please, thanks
i tried everything but it still doesn't want to work --.
i flashed the gingerbread rom it works perfectaly but slow as hell. even though i admit ics is a great rom to have, but why cant someone find a solution to this stupid problem
socialspider11 said:
i tried everything but it still doesn't want to work --.
i flashed the gingerbread rom it works perfectaly but slow as hell. even though i admit ics is a great rom to have, but why cant someone find a solution to this stupid problem
Click to expand...
Click to collapse
Sounds like a bug. Try flashing DXLP9.
socialspider11 said:
i am having a problem with my samsung galaxy s2, the power menu doesnt come up when i press the shut down button but it switches off straight away, and the lock screen doesnt work, non of them does. i would be so grate full for who ever can find me a solution
Click to expand...
Click to collapse
You're missing your /efs/imei/keystr file. Do a google search for "/efs/imei/keystr fix". You'll need root to apply the fix.
i360* said:
Sounds like a bug. Try flashing DXLP9.
Click to expand...
Click to collapse
This MIGHT work instead of what I suggested above, but I didn't think firmware flashes included or built/rebuilt the keystr file. I could be wrong though.
same problem..fixed after rooting
same problem here...just upgraded from 2.3.5 to Android ICS I9100XWLP7 and facing the exact issue of no screen lock and no power button menu....
Update:
Rooted phone using http://forum.xda-developers.com/showthread.php?t=1501719
and
fixed issue using http://forum.xda-developers.com/showthread.php?p=26542830#post26542830
darengive said:
same problem here...just upgraded from 2.3.5 to Android ICS I9100XWLP7 and facing the exact issue of no screen lock and no power button menu....
Click to expand...
Click to collapse
Dude. Look one post up.
thanks
ctomgee said:
Dude. Look one post up.
Click to expand...
Click to collapse
thanks, wanted to share info...
I had the same problem last week, this thread solved it for me, follow it from the 7th post to the end: http://forum.xda-developers.com/showthread.php?t=1547449&page=2
Thank You, it works a treat.
solved .. atlast
ried everything, then I found a s2 with working power menu and everything .. noted its firmware .. searched on net (link given below) and flashed everything in package .. everything is running as it should .. Sharing it coz I didnt find proper solution for me anywhere .
http://www.trickytweaks.com/i9100xxlsj-4-1-2-galaxy-s2-i9100-jelly-bean-update-tutorial.html
Root your device then open root folder with x-plore app after that go to following directory
efc>imei
Creata a file
Keystr
Openfile as text and write "ON"
Save the file
Tap and hold the file a menu will pop up click on permission
First deselect all boxes and click ok
Again go to permission and select all boxes under read write column click ok
Go to settings>lock screen
Re-enable Lock instantly with power button option.
---------- Post added at 03:17 AM ---------- Previous post was at 02:53 AM ----------
Root your device then open root folder with x - plore app after that go to following directory
efc / imei
Creata a file Keystr
Openfile as text and write " ON " Save the file
Tap and hold the file a menu will pop up click on permission
First deselect all boxes and click ok
Again go to permission and select all boxes under read write column click ok
Go to settings > lock screen
Re - enable Lock instantly with power button option
:good:
---------- Post added at 03:25 AM ---------- Previous post was at 03:17 AM ----------
Root your device then open root folder with x - plore app after that go to following directory
efc / imei
Create a file named "Keystr"
Openfile as text and write " ON " Save the file
Tap and hold the file a menu will pop up click on permission
First deselect all boxes and click ok
Again go to permission and select all boxes under read write column and click ok
Go to settings > lock screen
Re - enable Lock instantly with power button option.
:good:
Micromax officially has released the update for Canvas HD A116 today and it supports Over the air (OTA) updates and is only available on MMX service centers.
Please get the updated rom on XDA so we can flash it at our homes :laugh:
updated JellyBean 4.2.1 with OTA functionality
GPS fixed
clear pictures from camera
check : MMX NewsCaster
check : FoneArena
You can download the stock 4.2.1 JellyBean from Here
All The things you need to Upgrade to 4.2.1 are given Here
To Flash the JellyBean 4.2.1 you need to do the Following steps and follow the steps or you may mess up the touch panel as the last part is tricky:
So here is a complete guide to update Micromax Canvas HD A116 to Android 4.2 Jelly Bean OS.
REQUIREMENTS
• A Micromax Canvas HD A116 with usb data cable
• Please ensure that the battery of your device is above 75%, so you don't get sudden shut down during our process.
• Take full backup of your device.
• Backup data like SMS, contacts, whatsapp data etc etc., as these would be formatted during the process.
• Install the drivers of Micromax Canvas HD from the official Micromax website.
• Download Jelly Bean OS ROM & SP FLASH TOOLS, that you will flash.
• Take the backup of the Calibration with the help of Maui Meta (This is to be done incase you mess up any thing while the upgrade. restore the calibration taken before flashing into the newly flashed rom)
INSTALLATION:
1. Install drivers - Mobistel_Cynus_T1_Drivers_x86
2. Open SP_Flash_Tool_v3.1304.0.119
3. Select Scatter file from the downloaded ROM version 4.2.1 (extract downloaded file from winrar to different folder)and select all files.
4.Goto options->select usb & select USB Mode& DA Download All - & select force to High Speeds
5. Remove battery, Sim Cards & Memory Card
6. Press Firmware Upgrade (Don’t press download)
7. Insert USB data cable to PC & connect your phone & flash tool will detect your phone& downloadingstart automatically
8. When you see green circle than you are done.
9. Remove the cable from your phone insert battery & restart your phone.
10. It will take some times while re-starting and there will be TP Update popup. *
11. You are done& you can insert sim cards & memory card.
*NOTE:
After Flashing and updating from 4.1.2 to 4.2.1 there will be a TP UPDATE pop up which will update the TP automatically. So it is advised DON'T TOUCH PHONE's SCREEN ON FIRST BOOT (don't even press the OK button), LET THE TP UPGRADE DO HIS WORK,WAIT FOR AT LEAST 10-15 MINUTES BEFORE DOING ANYTHING.
When this appears you are done
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
CompsGeek said:
Micromax officially has released the update for Canvas HD A116 today and it supports Over the air (OTA) updates and is only available on MMX service centers.
Please get the updated rom on XDA so we can flash it at our homes :laugh:
updated JellyBean 4.2.1 with OTA functionality
GPS fixed
clear pictures from camera
check : mmxnewscaster
check : fonearena
You can download the stock 4.2.1 JellyBean from Here
Click to expand...
Click to collapse
thnk u 4 informing...can u plz tell me how to flash this rom because i am new to xda...i doesnt know anything about flashing and i cannot go to service centre because there is no service centre in my area...so i want to flash it at my own only...and what is imei breaking...will my imei break after flashing plz help...step by step..
jayas.mayank said:
thnk u 4 informing...can u plz tell me how to flash this rom because i am new to xda...i doesnt know anything about flashing and i cannot go to service centre because there is no service centre in my area...so i want to flash it at my own only...and what is imei breaking...will my imei break after flashing plz help...step by step..
Click to expand...
Click to collapse
Ok you need the below files :
SP flash tool preferably v3.13 as v3.12 gives errors
The official rom provided in above link
And your phone obviously
And micromax a116 usb drivers
Steps :
Install the drivers if you have driver issues check threads on that
After installing the drivers extract the firmware in the .rar file also extract sp tools and run as admin.
Select the scatter option and select the file MT6589_Android_scatter_emmc.txt and hit ok
Check all options are checked n go to tools and see its forced to high speed
Now most important part hit upgrade firmware and not download it will search 4 your phone then connect your phone without sim and battery it will install it a green circle pops up means u r done.
Now start the phone and leave it aside as a TP update message will pop up now do not touch the phone or touch screen at that point even when it asks to hit OK dont touch it it will automatically update it leave the phone even if screen goes off hit the unlock button after 10 mins but dont touch thr screen
When it says upgrade completed then you are done ...
DO NOT TOUCH YOUR PHONE WHILE THE FIRST REBOOT AS TP IS UPGRADING...IF YOU TOUCH IT EVEN TO PRESS OK IT WONT WORK AND PHONE WILL LOSE ITS TOUCH
After TP Upgrade completes it will look like the image in attachments then PRESS OK and you are done
Hope this helps you if you have any problem feel free to ask
Steps
Please update Steps to install ROM, I'm using 4.1.2 stock ROM. :fingers-crossed:
---------- Post added at 08:54 PM ---------- Previous post was at 08:50 PM ----------
CompsGeek said:
Ok you need the below files :
SP flash tool preferably v3.13 as v3.12 gives errors
The official rom provided in above link
And your phone obviously
And micromax a116 usb drivers
Steps :
Install the drivers if you have driver issues check threads on that
After installing the drivers extract the firmware in the .rar file also extract sp tools and run as admin.
Select the scatter option and select the file MT6589_Android_scatter_emmc.txt and hit ok
Check all options r checked n go to tools and see its forced to high speed
Now most important part hit upgrade firmware and not download it will search 4 your phone then connect your phone without sim and battery it will install it a green circle pips up means u r done
Now start the phone and leave it aside as a TP update message will pop up now do not touch the phone or touch screen at that point even when it asks to hit OK dont touch it it will automatically update it leave the phone even if screen goes off hit the unlock button after 10 mins but dont touch thr screen
When it says upgrade completed then you are done ...
Hope this helps you if you have any problem feel free to ask
Click to expand...
Click to collapse
Great.. will give it a try now..
Btw , is speaker mode and data connection working.? have you tested this? I know its stupid question for a official release, but I had real bad experience with some custom 4.2 ROM.
belibebond said:
Please update Steps to install ROM, I'm using 4.1.2 stock ROM. :fingers-crossed:
---------- Post added at 08:54 PM ---------- Previous post was at 08:50 PM ----------
Great.. will give it a try now..
Btw , is speaker mode and data connection working.? have you tested this? I know its stupid question for a official release, but I had real bad experience with some custom 4.2 ROM.
Click to expand...
Click to collapse
I am replying to this thread on my phone itself and checking every thing i can.
The screen looks better and no lags on stock launcher
Speaker during calls works perfectly and we can move apps to external sd without issues
Camera has improved but i am not satisfied with photosphere and i need to test it further.
I also had a problem in messaging for idea sim to enable cell broadcast and that was same in previous version .. It may b Sim card fault as loop works fine..
Will be testing it all out tonight
Added screens for the Micromax OTA software updater showing system upto date
Also no issues with the net connection 3g or wifi
Gps locks location quickly too
USB
CompsGeek said:
I am replying to this thread on my phone itself and checking every thing i can.
The screen looks better and no lags on stock launcher
Speaker during calls works perfectly and we can move apps to external sd without issues
Camera has improved but i am not satisfied with photosphere and i need to test it further.
I also had a problem in messaging for idea sim to enable cell broadcast and that was same in previous version .. It may b Sim card fault as loop works fine..
Will be testing it all out tonight
Added screens for the Micromax OTA software updater showing system upto date
Also no issues with the net connection 3g or wifi
Gps locks location quickly too
Click to expand...
Click to collapse
Drivers are installed, but still my phone is not getting detected. it keeps searching. all other settings are as you explained. any suggestions?
Right now, USB debugging is on and charge only mode is selected.
---------- Post added at 11:41 PM ---------- Previous post was at 11:36 PM ----------
belibebond said:
Drivers are installed, but still my phone is not getting detected. it keeps searching. all other settings are as you explained. any suggestions?
Right now, USB debugging is on and charge only mode is selected.
Click to expand...
Click to collapse
So dumb of me, i had to remove battery and sim and then connect, i was trying to connect directly first, thought i should connect without battery once it gets detected when phone is one.
its working.. 60% now.. fingers crossed.
---------- Post added at 11:56 PM ---------- Previous post was at 11:41 PM ----------
belibebond said:
Drivers are installed, but still my phone is not getting detected. it keeps searching. all other settings are as you explained. any suggestions?
Right now, USB debugging is on and charge only mode is selected.
---------- Post added at 11:41 PM ---------- Previous post was at 11:36 PM ----------
So dumb of me, i had to remove battery and sim and then connect, i was trying to connect directly first, thought i should connect without battery once it gets detected when phone is one.
its working.. 60% now.. fingers crossed.
Click to expand...
Click to collapse
Firmware update failed!!! now touch screen is not working!! help [email protected]
Phone touch screen not working.. help
Help.............. touch screen not working
belibebond said:
Help.............. touch screen not working
Click to expand...
Click to collapse
explain the exact process of how you did it .
phone should be switched off while upgrade battery should b removed
did you get green circle at the end of the upgrade ??
if upgrade from pc was successful and you started your phone.... did u touch the screen
because the phone does a TP upgrade i.e TOUCH PANEL and you should not touch the screen at any costs
if you did then it wont work
re flash it again
CompsGeek said:
explain the exact process of how you did it .
phone should be switched off while upgrade battery should b removed
did you get green circle at the end of the upgrade ??
if upgrade from pc was successful and you started your phone.... did u touch the screen
because the phone does a TP upgrade i.e TOUCH PANEL and you should not touch the screen at any costs
if you did then it wont work
re flash it again
Click to expand...
Click to collapse
So hereis a complete guide to update Micromax Canvas HD A116 to Android 4.2 Jelly Bean OS.
REQUIREMENTS
• A Micromax Canvas HD A116 with usb data cable
• Please ensure that the battery of your device is above 75%, so you don't get sudden shut downduring our process.
• Take full backup ofyour device.
• Backup data like SMS, contacts, whatsapp data etc etc., as these wouldbe formattedduring the process.
• Install the drivers ofMicromax Canvas HD from the officialMicromax website.
• Download Jelly Bean OS ROM & SP FLASH TOOLS, that you will flash.
• Link for ROM Version 4.2.1:
http://www.moulnisky.com/downloads/...201_4.2_MP_F3F8_B1_IN_MMX_09_FLASHER_USER.rar
INSTALLTION NOTE:
1. Install drivers - Mobistel_Cynus_T1_Drivers_x86
2. OpenSP_Flash_Tool_v3.1304.0.119
3. Select Scatter file fromthe downloadedROM version 4.2.1 (extract downloadedfile from winrarto different folder)and select all files.
4.Goto options->select usb & select USB Mode& DA DownloadAll - & select forceto High Speeds
5. Remove battery, Sim Cards & Memory Card
6. Press Firmware Upgrade (Don’t press download)
7. Insert USB data cable to PC & connect your phone & flash tool will detect your phone& downloadingstart automatically
8. Whenyou see greencircle than you are done.
9. Remove the cable from your phoneinsert battery & restart your phone.
10. It will take some times while re-starting and there will be TP Update popup. *
11. You are done& you can insert sim cards & memory card.
*NOTE:
After Flashing and updating from 4.1.2 to 4.2.1 there will be a TP UPDATE pop upwhich will update the TP automatically. So it is advised DON'T TOUCH PHONE's SCREEN ON FIRST BOOT (don't even press the OK button), LET THE TPUPGRADE DO HIS WORK,WAIT FOR AT LEAST 10-15 MINUTES BEFORE DOING ANYTHING.
but doc file where firmware dowmloaded says remove battery n insert again...
s-X-s said:
but doc file where firmware dowmloaded says remove battery n insert again...
Click to expand...
Click to collapse
no need to insert battery my phone is working fine you can insert battery if you want i have posted my tried and tested method
flash it without battery green ring pops up n you are golden .
only tricky part is the TP Upgrade
ive posted the tp screenshot DO NOT TOUCH THE SCREEN DURING THE TP
Did you fix this issue? I also stuck here!!!
belibebond said:
Help.............. touch screen not working
Click to expand...
Click to collapse
Did you fix this issue? I also stuck here!!!
---------- Post added at 04:19 AM ---------- Previous post was at 04:11 AM ----------
On TP UPGRADE - I touched screen mistakenly and so I did flashed again now I get TP UPgrade screen with start button but unable to hit start button on touch screen. Should I need to click on start button on the popup? or does the system take care of it? Pls help me.
---------- Post added at 04:58 AM ---------- Previous post was at 04:19 AM ----------
deepak_dpk said:
Did you fix this issue? I also stuck here!!!
---------- Post added at 04:19 AM ---------- Previous post was at 04:11 AM ----------
On TP UPGRADE - I touched screen mistakenly and so I did flashed again now I get TP UPgrade screen with start button but unable to hit start button on touch screen. Should I need to click on start button on the popup? or does the system take care of it? Pls help me.
Click to expand...
Click to collapse
The TP Upgrade welcome screen stays for almost 20 minutes without any activity
Touch screen not working.
CompsGeek said:
explain the exact process of how you did it .
phone should be switched off while upgrade battery should b removed
did you get green circle at the end of the upgrade ??
if upgrade from pc was successful and you started your phone.... did u touch the screen
because the phone does a TP upgrade i.e TOUCH PANEL and you should not touch the screen at any costs
if you did then it wont work
re flash it again
Click to expand...
Click to collapse
I followed the procedure properly.. Removed batter and sim and connected device to SP tool. It started downloading automatically and that green circle came up saying update successful.
After that turned on my phone, TP update pop up came up in no time.... suddenly one more pop up on screen came saying update failed ( i think it said firmware update failed ). Later i selected OK ( may be this is where it went wront, the TP update was still there in background ). Later i turned on mobile, it will come stuck in welcome screen for me to select language, touch , softkeys nothing works..
I tried same procedure again, also tried old roms.... but no luck, that TP upgrade pop up never came again and phone will always get stuck waiting for me to select language.
Any suggestion..
Also used Maui Meta to download parameters to phone, it dint work out too
Help please.
belibebond said:
I followed the procedure properly.. Removed batter and sim and connected device to SP tool. It started downloading automatically and that green circle came up saying update successful.
After that turned on my phone, TP update pop up came up in no time.... suddenly one more pop up on screen came saying update failed ( i think it said firmware update failed ). Later i selected OK ( may be this is where it went wront, the TP update was still there in background ). Later i turned on mobile, it will come stuck in welcome screen for me to select language, touch , softkeys nothing works..
I tried same procedure again, also tried old roms.... but no luck, that TP upgrade pop up never came again and phone will always get stuck waiting for me to select language.
Any suggestion..
Also used Maui Meta to download parameters to phone, it dint work out too
Help please.
Click to expand...
Click to collapse
Im also on exactly same state. Going to try flashing 4.1.2 official firmware tomorrow.
Done that already
deepak_dpk said:
Im also on exactly same state. Going to try flashing 4.1.2 official firmware tomorrow.
Click to expand...
Click to collapse
tried that too.. dint work.. TP is broken now.. need that TP upgrade somehow.. or calibration of screen is needed , unfortunately that is also not working for me.
---------- Post added at 10:08 AM ---------- Previous post was at 09:54 AM ----------
CompsGeek said:
no need to insert battery my phone is working fine you can insert battery if you want i have posted my tried and tested method
flash it without battery green ring pops up n you are golden .
only tricky part is the TP Upgrade
ive posted the tp screenshot DO NOT TOUCH THE SCREEN DURING THE TP
Click to expand...
Click to collapse
I installed multiple times now.. not getting that TP upgrade. I dont think my phone will ever get any better without that TP upgrade.. am i missing something?
Hey..if I flash this official ROM will my warranty get over....
Ps:- I'm a n00b I have a canvas HD un-rooted and I wish to flash this ROM via so tools....pls reply ASAP
Sent from my Micromax A116 using xda premium
What i did during the TP UPGRADE
Start the phone and keep it aside.
it will show tp popup DON'T PRESS OK
THE PROCESS IS STARTING BEHIND THE POPUP
look at the screen carefully
in case screen goes off press power button once without touching panel
it may stay or take longer than 15 mins
it should be upgraded successfully..
belibebond said:
tried that too.. dint work.. TP is broken now.. need that TP upgrade somehow.. or calibration of screen is needed , unfortunately that is also not working for me.
---------- Post added at 10:08 AM ---------- Previous post was at 09:54 AM ----------
I installed multiple times now.. not getting that TP upgrade. I dont think my phone will ever get any better without that TP upgrade.. am i missing something?
Click to expand...
Click to collapse
Few more options to try:
Vol + & Vol - & Power button hold for few sec and then click Vol - ( factory mode) In factory mode there is an option for TP Upgrade but I dont know which key combination does the enter operation. Does any one know that?
Option 2 (most likely will not work)
Try to add a mouse via usb otg and try clicking the start button (Most likely usb otg may not work on that mode but still we may give a try)
---------- Post added at 07:39 AM ---------- Previous post was at 07:32 AM ----------
CompsGeek said:
What i did during the TP UPGRADE
Start the phone and keep it aside.
it will show tp popup DON'T PRESS OK
THE PROCESS IS STARTING BEHIND THE POPUP
look at the screen carefully
in case screen goes off press power button once without touching panel
it may stay or take longer than 15 mins
it should be upgraded successfully..
Click to expand...
Click to collapse
I mistakenly clicked ok and so the TP Upgrade failed and I'm stuck at start screen (language selection) Is there any way can I recover and re do the TP UPGRADE?
deepak_dpk said:
Few more options to try:
Vol + & Vol - & Power button hold for few sec and then click Vol - ( factory mode) In factory mode there is an option for TP Upgrade but I dont know which key combination does the enter operation. Does any one know that?
Option 2 (most likely will not work)
Try to add a mouse via usb otg and try clicking the start button (Most likely usb otg may not work on that mode but still we may give a try)
---------- Post added at 07:39 AM ---------- Previous post was at 07:32 AM ----------
I mistakenly clicked ok and so the TP Upgrade failed and I'm stuck at start screen (language selection) Is there any way can I recover and re do the TP UPGRADE?
Click to expand...
Click to collapse
To enter the factory mode the enter key is the combination of two touch buttons Menu and back pressed simultaneously but as the tp is not working i think that wont work
deepak_dpk said:
Few more options to try:
Vol + & Vol - & Power button hold for few sec and then click Vol - ( factory mode) In factory mode there is an option for TP Upgrade but I dont know which key combination does the enter operation. Does any one know that?
Option 2 (most likely will not work)
Try to add a mouse via usb otg and try clicking the start button (Most likely usb otg may not work on that mode but still we may give a try)
---------- Post added at 07:39 AM ---------- Previous post was at 07:32 AM ----------
I mistakenly clicked ok and so the TP Upgrade failed and I'm stuck at start screen (language selection) Is there any way can I recover and re do the TP UPGRADE?
Click to expand...
Click to collapse
Went till factory mode and TPupgrade.. but menu button is not working..none of the soft keys are working.. so not able to select TPupgrade option.. any other ideas.. I dont have USB otg
Hello, I need help with an amazfit beep, when updating in IOS to the latest version the clock was on screen a message that said "connect app to update resources".
Then I linked the clock to an android and using gadgetbridge install the res 9.40 and then the fw 9.26 then in this last step the clock did not end and it was turned off. Now I can not turn it on or in the charging base.
Help
Mine was in bricked mode since a month ago.
Was using the Notify n Fitness app, then out of sudden i decide to manually converting to another rom. the first phase was successful. but then, it restarted to 2nd phase, unfortunately it didn't managed to get there... stay in 'sleep mode' ever since.
revolutionyo said:
Hello, I need help with an amazfit beep, when updating in IOS to the latest version the clock was on screen a message that said "connect app to update resources".
Then I linked the clock to an android and using gadgetbridge install the res 9.40 and then the fw 9.26 then in this last step the clock did not end and it was turned off. Now I can not turn it on or in the charging base.
Help
Click to expand...
Click to collapse
Any status on this brick? Same happened to me few moments ago
I am with the same problem. Please, must be a solution... anyone knows something? Thanks in advance
Me2 same with this like that.
For first poster : You have to flash first FW, THEN .res.
Maybe that's why.
To flash the 2 files, i used Notify & Fitness today and all ok.
FW : 0.1.0.27
And once it's bricked, for now, I haven't seen anyone recovering it...
Mine was brick as well. I followed the tutorial of one of the thread here
vernel1008 said:
Mine was brick as well. I followed the tutorial of one of the thread here
Click to expand...
Click to collapse
Which tutorial have you followed and did it help ?
---------- Post added at 10:39 AM ---------- Previous post was at 10:38 AM ----------
My watch is not dead but it's bootlooping this is after I tried to update the latest firmware using mi fit app and it failed now mi fit app won't recognize the device it says "unable to connect please restart the Bluetooth and try again". The watch turn on with backlight then backlight turns off after few seconds and just a second after backlight turn off the watch turns off and turn on again.The watch show the correct time and have it's default watchface. Does anybody know how to resolve this issue.
vmirjolkar said:
Which tutorial have you followed and did it help ?
---------- Post added at 10:39 AM ---------- Previous post was at 10:38 AM ----------
My watch is not dead but it's bootlooping this is after I tried to update the latest firmware using mi fit app and it failed now mi fit app won't recognize the device it says "unable to connect please restart the Bluetooth and try again". The watch turn on with backlight then backlight turns off after few seconds and just a second after backlight turn off the watch turns off and turn on again.The watch show the correct time and have it's default watchface. Does anybody know how to resolve this issue.
Click to expand...
Click to collapse
We have two watches in my family and both of them have the same problem that you explained above. Have you got the solution?
vinczetibor said:
We have two watches in my family and both of them have the same problem that you explained above. Have you got the solution?
Click to expand...
Click to collapse
Same problem. As far as I understand, "brick" is not treated. There is no solution to the problem (((
Got bootloop after pair with new phone T_T
Sent from my SM-N950F using Tapatalk
vmirjolkar said:
Which tutorial have you followed and did it help ?
---------- Post added at 10:39 AM ---------- Previous post was at 10:38 AM ----------
My watch is not dead but it's bootlooping this is after I tried to update the latest firmware using mi fit app and it failed now mi fit app won't recognize the device it says "unable to connect please restart the Bluetooth and try again". The watch turn on with backlight then backlight turns off after few seconds and just a second after backlight turn off the watch turns off and turn on again.The watch show the correct time and have it's default watchface. Does anybody know how to resolve this issue.
Click to expand...
Click to collapse
Hi There,
I'm also facing the bootlopping issue, I tried using another phone to pair. after many tries, I;m able to see the paring screen but I;m unable to press the 'Tick' icon then after awhile it will auto reboot again.
have you found a way to fix it yet?
alfenneo said:
Hi There,
I'm also facing the bootlopping issue, I tried using another phone to pair. after many tries, I;m able to see the paring screen but I;m unable to press the 'Tick' icon then after awhile it will auto reboot again.
have you found a way to fix it yet?
Click to expand...
Click to collapse
I haven't found fix for this one.
https://www.tuttoandroid.net/xiaomi/scopriamo-un-amazfit-bip-un-teardown-inconsueto-525801/
I came across the above link regarding the teardown of amzefit bip and it says if the wrong firmware is flashed and if the watch bricks it can be unbricked by using the testing points available on motherboard of the watch. I don't have a decent electronics background so didn't understood it.
Finally I just understood that it's possible but, not for common user like me (unless someone creates a proper tutorial)
Hi,
I have the same issue.
Do you find something ?
Regards
Envoyé de mon LG-H870DS en utilisant Tapatalk
I have the same problem, bootloop and can't connect anymore:/
Hi,
I'm facing a strange Black Screen Problem even after booting of the phone successfully every time. I can see the lock screen every time for like 2-3 seconds then suddenly entering to black screen automatically if I try to unlock or don't attempt to do so. The phone is able to ring if I try to make a call from other no. but won't able to pick up because there is no option to answer or decline the call. If I hit the power button all power menu buttons are coming like to reboot, power off , airplane mode etc but some how I'm not able to access the phone from inside.
Please note that last time when the phone was running fine I saw one error like android.system.mui has stopped working and everything was crashing so I had to reboot my phone and ultimately landed into this issue. Also my internal storage was like 600-500 MB free that time.
I'm on miui 9 official for Redmi Note 4 ( 32GB version SD 625).
I'm a new member of XDA and I haven't read all the rules yet, so I apologies if I do any mistake please correct me if I'm wrong as this my first post in XDA. I respect all the community guidelines.
Please provide the working solution for this.
A few quick questions as follows
- Do I have to install TWRP recovery for the same to clear cache which i think it may resolve the issue just removing the cache?
- I'm not sure about Miui recovery 3.0 clear data option to clear cache as i don't really want to erase my all important documents, photos, videos, notes in my phone.
- How can I recover my data if I had to reset my device ?
Please guide me for the above issue.
I really appreciate all your concerns.
Thanks & Regards,
Gaurav Kumar
I have exactly same problem, please help with solution.
gkfc007 said:
Hi,
I'm facing a strange Black Screen Problem even after booting of the phone successfully every time. I can see the lock screen every time for like 2-3 seconds then suddenly entering to black screen automatically if I try to unlock or don't attempt to do so. The phone is able to ring if I try to make a call from other no. but won't able to pick up because there is no option to answer or decline the call. If I hit the power button all power menu buttons are coming like to reboot, power off , airplane mode etc but some how I'm not able to access the phone from inside.
Please note that last time when the phone was running fine I saw one error like android.system.mui has stopped working and everything was crashing so I had to reboot my phone and ultimately landed into this issue. Also my internal storage was like 600-500 MB free that time.
I'm on miui 9 official for Redmi Note 4 ( 32GB version SD 625).
I'm a new member of XDA and I haven't read all the rules yet, so I apologies if I do any mistake please correct me if I'm wrong as this my first post in XDA. I respect all the community guidelines.
Please provide the working solution for this.
A few quick questions as follows
- Do I have to install TWRP recovery for the same to clear cache which i think it may resolve the issue just removing the cache?
- I'm not sure about Miui recovery 3.0 clear data option to clear cache as i don't really want to erase my all important documents, photos, videos, notes in my phone.
- How can I recover my data if I had to reset my device ?
Please guide me for the above issue.
I really appreciate all your concerns.
Thanks & Regards,
Gaurav Kumar
Click to expand...
Click to collapse
Are you able to boot into the recovery and use it? Or does the recovery shows the black screen also?
hey I`ve just got the same problem in Redmi note 4, did u find any solution?...
so far what i did till now is, flash Red Wolf Recovery, wipe, DALVICK, CACHE and DATA (not the internal storage where is your info), the wipe is like a factory reset, is the only solution I`ve found so far.
any ideas?
MyNameIsRage said:
Are you able to boot into the recovery and use it? Or does the recovery shows the black screen also?
Click to expand...
Click to collapse
Facing same issue, i am able to boot into recovery mode ( volumen up + power ) and i can select options there, any solutions ?
Fr34kD3V said:
Facing same issue, i am able to boot into recovery mode ( volumen up + power ) and i can select options there, any solutions ?
Click to expand...
Click to collapse
Do you have a unlocked bootloader? If you don't then possibly resetting device from recovery is the only thing.
Does this issue already solved? I also have the same issue but I don't know how to fix it. Please help me
HI
I have the same problem, I tried using the fastboot (power+volume down) and nothing happened, I tried the recovery mode (power + volume up) and I got three options, (reboot, wipe data, connect with mi assistant) the first would reboot the phone to the same problem, the second one I don't want to wipe all data or reset the phone as I want to retrieve the data on it, I tried the third and downloaded the mi pc suite, but the phone doesn't show on my pc, I receive the no device detected even after connecting my phone with USB
I have the same issue on my Mi Max 2!!!
And the developer mode isn't possible to enable, because of this black screen!
Please help!
MyNameIsRage said:
Are you able to boot into the recovery and use it? Or does the recovery shows the black screen also?
Click to expand...
Click to collapse
I updated my Mi Note 4 system software yesterday to MIUI 9.6 (me thinks), but it is having booting issues. I struggled 2 hours last night to get it started but in the morning I noticed that the fingertip sensor isnt working. I cleared cache, added new finger print, still the problem persisted and then I read on the forum to power off and restart the phone. I clicked on power off and since then my phone is not rebooting. The screen in black, I can hear phone calls, msg notifications. I have tried pressing the power button for 40 seconds (as per the MI Support Tech's advice), followed by using the fastboot (power+volume down) and nothing happened, I tried the recovery mode (power + volume up). Still nothing is showing. The Mi logo and android restart option isn't showing only. The phone is black. I can see navigation light and the blue light blinking on the top left when msg/notification comes. I haven't taken a back up since many many months. I don't want to lose my data. Please help.
amtrips2018 said:
I updated my Mi Note 4 system software yesterday to MIUI 9.6 (me thinks), but it is having booting issues. I struggled 2 hours last night to get it started but in the morning I noticed that the fingertip sensor isnt working. I cleared cache, added new finger print, still the problem persisted and then I read on the forum to power off and restart the phone. I clicked on power off and since then my phone is not rebooting. The screen in black, I can hear phone calls, msg notifications. I have tried pressing the power button for 40 seconds (as per the MI Support Tech's advice), followed by using the fastboot (power+volume down) and nothing happened, I tried the recovery mode (power + volume up). Still nothing is showing. The Mi logo and android restart option isn't showing only. The phone is black. I can see navigation light and the blue light blinking on the top left when msg/notification comes. I haven't taken a back up since many many months. I don't want to lose my data. Please help.
Click to expand...
Click to collapse
Did by any chance you flashed miui 10?
MyNameIsRage said:
Did by any chance you flashed miui 10?
Click to expand...
Click to collapse
No I haven't done flash method. I don't know how to do it.
i experienced the same thing with my mido . boot logo and splash screen appeared normally . when it goes to home screen , it is totally black (but the backlight in blackscreen still working if i press finger scanner or power button) . press power button , the menus shows ! restart , shutdown , boot to recovery , fastboot , et cetera ... i've already clear cache , dalvik & fix context in twrp , but after all it's just the same .. just black . when somebody's calls , the phone's ringing but i can't answer it . the daily alarm's still working but i can't snooze it . please i don't want to clear my data / install any other roms .. Thanks ..
please apologize my bad english
i was facing the same issue after 9.6.1 update.... the only working option i got was resetting the deivce and lost all data.
rajshahbazkhan said:
i was facing the same issue after 9.6.1 update.... the only working option i got was resetting the deivce and lost all data.
Click to expand...
Click to collapse
@amtrips2018 @ciilenx
MyNameIsRage said:
@amtrips2018 @ciilenx
Click to expand...
Click to collapse
i've fix it .. yeah as i thought before .. simply flash a new rom . and i flash miui 10 8.7.12 developer from miui web . do a twrp backup before, and after flash new rom , restore the data , and flash lazyflasher .. reboot to system .
Works flawlessly now .. @MyNameIsRage
ciilenx said:
i've fix it .. yeah as i thought before .. simply flash a new rom . and i flash miui 10 8.7.12 developer from miui web . do a twrp backup before, and after flash new rom , restore the data , and flash lazyflasher .. reboot to system .
Works flawlessly now .. @MyNameIsRage
Click to expand...
Click to collapse
Hi there, could you please explain the process a little bit more specifically? I have so many files in the phone and I could not lose them Thank you very much beforehand!
Vasilis123456789 said:
Hi there, could you please explain the process a little bit more specifically? I have so many files in the phone and I could not lose them Thank you very much beforehand!
Click to expand...
Click to collapse
Why don't you throw your data in a PC or a memory card? Also guys if im not mistaken you can not rollback from MIUI 10 to an earlier version if you update via the OTA right?Or else your phoned will be bricked am i right? Someone confirm this cause its risky.
Solution for mi black screen.
Hello friends,
I think the issue in sensors, because when i bump my mobile on my hand the screen wake up suddenly but some time screen in hang position but when i try it one or more time its working normally .
Same issue
Hi, I recently updated to the 9.6.2.0 in my Mi note 4 and after reboot it started to go off and on (only the backlight (touch layer worked)). I rebooted several times and get it going. after few minutes went black again and after reboot the fingerprint sensor stopped working (HW diagnostics saying error if you try to test it) and then the battery status started act weir. If i plug phone to charger, no matter how many % i ve got it charge only 1% (after hour or so)and if i unplug it lose 5% in 5 seconds and stays there for amount of time till the battery reach the same percentage as the indication is sayin.
TBH pretty weird and pretty annoying.
And yes it is probably sensor ( or a driver? ) because turning phone up-side down or covering the proximity sensor osometimes help.
I dont want to wipe my phone until it is necessary.
Is it because of update?
Thank you
Timekiller_CZ