I haven't been able to get any firmware to work in my Abox A1 Plus 2/8gb S905x. I don't have the original fw, and I can't find it anywhere.
I've read that some people were able to install Nexbox A95x firmware in this box, but I can't. The 6.0 firmware installs successfully (via USB), but it gets stuck at the logo when I connect the box to the TV. When I try Nexbox 7.1 firmware, the installation stops at 98% / 99% (error [0x30405004]UBOOT/Partition System/Verify partition/Error result ). I tried using the 'force/erase all', but didn't work.
Any ideas on how to solve this, or any users of this same box that can point me to a firmware that works?
http://www.mediafire.com/file/tc2vujexv235o4e/Gionee_A1_Plus_MT6757_0301_T5242_7.0.zip
samuau said:
I haven't been able to get any firmware to work in my Abox A1 Plus 2/8gb S905x. I don't have the original fw, and I can't find it anywhere.
I've read that some people were able to install Nexbox A95x firmware in this box, but I can't. The 6.0 firmware installs successfully (via USB), but it gets stuck at the logo when I connect the box to the TV. When I try Nexbox 7.1 firmware, the installation stops at 98% / 99% (error [0x30405004]UBOOT/Partition System/Verify partition/Error result ). I tried using the 'force/erase all', but didn't work.
Any ideas on how to solve this, or any users of this same box that can point me to a firmware that works?
Click to expand...
Click to collapse
Hi.
Can you give a link to this firmware ? Did you use short pin methods then connect usb male-male ??
Related
Hi Everyone,
I need firmware to flash via usb burning tool. i have tried around 20 different firmwares and had luck with 2 of them, unfortunately for me they keep stalling at the boot logo.
The A95x and Yundoo Y7 roms were the only firmware that worked.
Thanks in advance
dj10264 said:
Hi Everyone,
I need firmware to flash via usb burning tool. i have tried around 20 different firmwares and had luck with 2 of them, unfortunately for me they keep stalling at the boot logo.
The A95x and Yundoo Y7 roms were the only firmware that worked.
Thanks in advance
Click to expand...
Click to collapse
If u open the bottom off your android box the board usually has the model stamped on it. I tried lots of roms for my mxq box and found most of them didn't work. Also try using some of the sd card roms. I found some would load but brick the box. And if ye do brick yer android machine, don't panic coz can usually b fixes by flashing another rom
Hi All,
I just got a mxq pro 4K S905W android 7.1.2.
In order to use an app (which detect root), i have to remove the pre-installed root. By looking at some forum i found a solution which consist to install superSU first to be able after to unroot my device.
After I installed SuperSu i rebooted and got stuck on "android" logo.. I tried a factory reset from recovery menu but nothing changed...
Now i want to try to install a fresh FW but i'm not able to found it out, i can only find FW for S905 or S905X but not for S905W.
Can someone help me on this issue. Or at least point me to the right FW (by the way i don't care to have android 7.x, 6.x is Ok).
Thanks!
edit: I tried to install S905X FW for android 6.0, but it failed. I think because downgrade are not allowed.
Do you think i can install FW for a different but really similar box like w95 tv box (found 7.1.2 fw for it)?
David_shimo said:
Hi All,
I just got a mxq pro 4K S905W android 7.1.2.
In order to use an app (which detect root), i have to remove the pre-installed root. By looking at some forum i found a solution which consist to install superSU first to be able after to unroot my device.
After I installed SuperSu i rebooted and got stuck on "android" logo.. I tried a factory reset from recovery menu but nothing changed...
Now i want to try to install a fresh FW but i'm not able to found it out, i can only find FW for S905 or S905X but not for S905W.
Can someone help me on this issue. Or at least point me to the right FW (by the way i don't care to have android 7.x, 6.x is Ok).
Thanks!
edit: I tried to install S905X FW for android 6.0, but it failed. I think because downgrade are not allowed.
Do you think i can install FW for a different but really similar box like w95 tv box (found 7.1.2 fw for it)?
Click to expand...
Click to collapse
I have a w95 box and had the same problem after installing SuperUser the box is stuck on "Please Wait" boot.
There is a Reset button on the base of the device but it seems to be inoperative ... I had the box for 2 days and it is now a paper weight (not eve it is really tiny and light).
There isn't seem to be a way to access the bootloader or Recovery...
Really frustrated now.
905x & 905w use different boards.
At the moment SuperSU will install but if you update it it will bootloop your box.
Look at other s905w forums I think there is a firmware for a s995w board but I don't have the link right now.
It could be in freaktab Forum
mxq pro 4k botloop after superSU update
any suggestions about this problem? I can't find new firmware. What can I do now?
pkatsifaras said:
any suggestions about this problem? I can't find new firmware. What can I do now?
Click to expand...
Click to collapse
https://www.chinagadgetsreviews.com/download-android-7-1-stock-firmware-mxq-pro-4k-tv-box.html
---------- Post added at 02:58 AM ---------- Previous post was at 02:55 AM ----------
rjbweb said:
I have a w95 box and had the same problem after installing SuperUser the box is stuck on "Please Wait" boot.
There is a Reset button on the base of the device but it seems to be inoperative ... I had the box for 2 days and it is now a paper weight (not eve it is really tiny and light).
There isn't seem to be a way to access the bootloader or Recovery...
Really frustrated now.
Click to expand...
Click to collapse
https://www.chinagadgetsreviews.com/download-amlogic-burn_card_maker-v2-0-2.html
Hello everybody I am after some help please.
I own an Abox a1 plus android box s905x. Somehow the original firmware became currupt but there are no original firmwares on the net that I can find to get this box up and running again. With this said i have managed to get it running again through trial and error with a different rom.
The only thing is I am in need of the original remote.conf file to get the remote working again can anybody help as I fear i have run out of options.
Hi, Same request, i have remove many apps on original firmware and don't work after reboot, i flash nexbox 7.1 firmware all work fine but miss remote.conf original (Abox A1 plus 8gb/2gb - s905x, firmware original is marshmallow).
Thanks in advance.
djmagma59 said:
Hi, Same request, i have remove many apps on original firmware and don't work after reboot, i flash nexbox 7.1 firmware all work fine but miss remote.conf original (Abox A1 plus 8gb/2gb - s905x, firmware original is marshmallow).
Thanks in advance.
Click to expand...
Click to collapse
This exactly the firmware I got my Abox A1 plus running with too. It works brilliantly with no mods. I just needs that remote.conf file afaik.
I can't get any firmware to work on my Abox A1 Plus. It always gets stuck on the logo. Where did you download your firmware from?
samuau said:
I can't get any firmware to work on my Abox A1 Plus. It always gets stuck on the logo. Where did you download your firmware from?
Click to expand...
Click to collapse
Hi, take one firmware here but respect your memory configuration (2Gb ram and 8 Gb rom = 2-8G).
mega.nz/#F!F9xjTSSa!R0vJfTC2U6Qc2skNMrr1iQ!hlJDxRxQ
(add https before for full address, i don't have acces post link ^^ )
But if you have original again work backup your remote.conf in system/etc/, or remote dont work after upgrade. (and if you can backup, please post here your remote.conf file) thanks.
Sorry for bad english, i'm french.
Edit : I search for repair and i found we don't have a remote.conf but our file named remote_mouse2.tab
i found my factory code via dmesg –c on ssh and it's recognized, now i remap function one by one
The power on keycode is hardcoded in bootloader (and with this rom is different from original). All key work but if box off, power on with remote don't work.
Delete this please :/
djmagma59 said:
Hi, take one firmware here but respect your memory configuration (2Gb ram and 8 Gb rom = 2-8G).
mega.nz/#F!F9xjTSSa!R0vJfTC2U6Qc2skNMrr1iQ!hlJDxRxQ
(add https before for full address, i don't have acces post link ^^ )
Click to expand...
Click to collapse
Thanks for the link djmagma59! I already tried this specific firmware, but I get the burning tool error at 98% (see above). I'll try again tho. If I install the 6.0 version of the firmware the installation goes through, but the box gets stuck on boot (logo).
Did you have any issues installing it? Any ideas for me to try to solve it?
Again, I appreciate the help.
Hey I don't know if you still need it but I was looking for help myself and foud this thread, I have this box, it came with with 7.1.2 tho, I'm attaching the remote.conf file for you.
Need Basic Help for Resolving REboot Problem
Hi All,
I am facing loading my Abox A1 Plus . The screen is stuck reboot (bootloading). I can see options like Update using EXT , Update using ADB and so on. I tried Loading Zipped img files onto the USB and then update using EXt. But getting Signature Verification Failed Error. What are the basic steps as I could not find my device even after using AMLogic USB Tool.
Thanks in Advnace
Hello i have a tv box zkmagic A95X F3 Air that stopped working. It boots just in recovery, i tried flashing a firmware from sd card but doesn't want to flash its keep rebooting. I can see a little android with a text updating when the sd card is in but everytime reboot. What can i do?
where can I find twrp for a95x f3?
I have a A95X F3 Air smart tv box which fails to boot. Tried by doing reset procedure but remains as same. Please advise what further to regain it to normal
The A95X F3 Air is a bad box to buy. I too own it and am trying to get ATV compatible rom.
Reason
- Even though stock rom is from 2019, one can see the security from 2018. I suspect it leaks data to Chinese servers.
- Youtube on AOSP has poor UI on TV.
But looks like it has locked bootloader and is not compatible with great roms roaming around. I'm thinking to sell this off.
Hi. Tell me who didn't put magisk Su on this device?
P C Alexander said:
I have a A95X F3 Air smart tv box which fails to boot. Tried by doing reset procedure but remains as same. Please advise what further to regain it to normal
Click to expand...
Click to collapse
Hey use a usb to usb cable on computer. And flash from pc. Seems the sd flashing doesn't work. Use amlogic usb burning tool
This box was constantly freezing. Read somewhere that it requires a new firmware. The firmware that was on the box when I got it was 20181229. Tried to install a new firmware TANIX TX3 MAX & MINI "DUAL OS EDITION from usb stick using the method according to Tanix-box.com website " UPDATE FROM TF/USB MEMORY" . The software was loading fairly slowly so I stepped away for a moment and when I returned I had a blank screen on TV. Rebooted the box but only received the boot display and a black screen. realized I had bricked the box, Tried to download the same software using the usb burning tool but no go. I then tried the firmware TANIX TX3 MINI 20171220 using the usb burning tool. It downloads for about 7 seconds and then stops with an error. Obviously the wrong file. Here are the pics of my card. Sure hope someone can help me out. If I have to short a pin can you give me some details as I am pretty new at this. I do now have the original firmware and have looked everywhere, but can't find it. Thanks for any help on this issue, I've been reading and looking for a solution foe quit some time now.
Latest development, using USB Burning tool I loaded TX3Mini-20181210.img with no errors. I connected to TV and the T3 Mini logo cam on and the the android logo came on and was booting for just over 1 minute and then stopped and the display on the box was 0001.
billyfreeman said:
This box was constantly freezing. Read somewhere that it requires a new firmware. The firmware that was on the box when I got it was 20181229. Tried to install a new firmware TANIX TX3 MAX & MINI "DUAL OS EDITION from usb stick using the method according to Tanix-box.com website " UPDATE FROM TF/USB MEMORY" . The software was loading fairly slowly so I stepped away for a moment and when I returned I had a blank screen on TV. Rebooted the box but only received the boot display and a black screen. realized I had bricked the box, Tried to download the same software using the usb burning tool but no go. I then tried the firmware TANIX TX3 MINI 20171220 using the usb burning tool. It downloads for about 7 seconds and then stops with an error. Obviously the wrong file. Here are the pics of my card. Sure hope someone can help me out. If I have to short a pin can you give me some details as I am pretty new at this. I do now have the original firmware and have looked everywhere, but can't find it. Thanks for any help on this issue, I've been reading and looking for a solution foe quit some time now.
Latest development, using USB Burning tool I loaded TX3Mini-20181210.img with no errors. I connected to TV and the T3 Mini logo cam on and the the android logo came on and was booting for just over 1 minute and then stopped and the display on the box was 0001.
Click to expand...
Click to collapse
I installed TX3 mini 20181210.img on the box nd it worked. But the box is still freexing. Anyone else having this issue?
billyfreeman said:
I installed TX3 mini 20181210.img on the box nd it worked. But the box is still freexing. Anyone else having this issue?
Click to expand...
Click to collapse
Yo could try my custom Android TV 9 ROM, there are tx3 versions available, may work for you but no guarantees,
aidanmacgregor said:
Yo could try my custom Android TV 9 ROM, there are tx3 versions available, may work for you but no guarantees,
Click to expand...
Click to collapse
No doesn't work. Keep getting getinitial error