Hi all. I just recently unlocked the bootloader and rooted my LG V30+ following the WTF guide with no issues. However, I installed a "Hide navigation bar" module in Magisk and now the screen is in accessible and I can only reboot the phone. Since I have TWRP installed, I cannot boot into bootloader holding down the volume down and power buttons. Any suggestions? I cannot use adb becuase it says that the device is unauthorized since I cannot allow permisions on my screen ( cant see anything on screen atm).
Blueoval24 said:
However, I installed a "Hide navigation bar" module in Magisk and now the screen is in accessible and I can only reboot the phone. Since I have TWRP installed, I cannot boot into bootloader holding down the volume down and power buttons. Any suggestions? I cannot use adb becuase it says that the device is unauthorized since I cannot allow permisions on my screen ( cant see anything on screen atm).
Click to expand...
Click to collapse
You can boot to TWRP with hardware button dance.
8 sec Power + Vol-, and when it shuts off, release both, immediatly press both again (at the same time), and as soon as the LG V30 logo appears, release power and press/hold it again.
Should get you to the factory reset menu, confirm twice with "yes" (navigate via vol/power buttons), and TWRP should boot fine.
Might take a few tries to get the right timing for that
Click to expand...
Click to collapse
For that, remember the annoying bootloader unlock warning is part of the boot sequence.
Or do a Master Reset and start over.
ChazzMatt said:
You can boot to TWRP with hardware button dance.
For that, remember the annoying bootloader unlock warning is part of the boot sequence.
Or do a Master Reset and start over.
Click to expand...
Click to collapse
So Ive been doing the awesome Hardware button dance but no success. What should I do when I get to the unlock warming menu?
Thanks!
EDIT: The post you link finally got me to boot in recovery. Thanks so much!!!
Cant believe it was that picky!
Blueoval24 said:
So Ive been doing the awesome Hardware button dance but no success. What should I do when I get to the unlock warming menu?
Thanks!
Click to expand...
Click to collapse
Ignore bootloader unlock warning. It's just part of the boot sequence. Maybe it's considered the "logo". Don't let it freak you out.
Sent via open market LG US998 V30/V30+
I must have done this button dance 25 times now, it just goes between unlocked boot warning screen and LG SlimQ screen, over & over again. Still no luck.
eff you LG...
christoophat said:
I must have done this button dance 25 times now, it just goes between unlocked boot warning screen and LG SlimQ screen, over & over again. Still no luck.
eff you LG...
Click to expand...
Click to collapse
Suggestion... Why not boot to TWRP with fastboot commands like in the WTF instructions? Then reboot to TWRP from within TWRP (reboot to recovery, from Recovery) to make sure you are then on your phone TWRP and not your PC TWRP.
Then after you root, use the recommended power menu app to never have to worry about it again.
If you already have root, then just go install that right now.
ADVANCED POWER MENU (root needed)
https://forum.xda-developers.com/showpost.php?p=79573776&postcount=2963
The person who started this thread couldn't do that because they installed something which messed up their screen. They couldn't see the Advanced Power Menu, nor see ADB/fastboot. So they HAD to use the hardware button dance...
Really no one else ever has to do that, except T-Mobile H932 users who don't have fastboot flash commands.
Hi Chazz, been unlocked and rooted with TWRP installed for months now. Wanted to just refresh us998 H, since something in Anxious mod may have been causing some issues. Wiped cache & dal, flashed the zip, flashed magisk 18.1, then rebooted to system. Magisk showing as not installed. Wanted to get back to recovery & reflash magisk....except now I can't for the life of me get back in there. New PC build here, nothing set up yet to be able to do fastboot stuff. Dang this is frustrating.
christoophat said:
Hi Chazz, been unlocked and rooted with TWRP installed for months now. Wanted to just refresh us998 H, since something in Anxious mod may have been causing some issues. Wiped cache & dal, flashed the zip, flashed magisk 18.1, then rebooted to system. Magisk showing as not installed. Wanted to get back to recovery & reflash magisk....except now I can't for the life of me get back in there. New PC build here, nothing set up yet to be able to do fastboot stuff. Dang this is frustrating.
Click to expand...
Click to collapse
In Oreo, did you enable USB debugging and then allow ADB from this PC? You have to install ABD drivers, LG drivers, fastboot drivers, and connect via good USB-C cable. If so go into ADB folder, hold-shift and right click to 'open command prompt here', and type "adb devices". If the PC recognizes your phone then it should say "adb xxxxxxxx authorized". Then type "adb reboot recovery" and it should boot into TWRP. If not then repeat everything and type "adb reboot bootloader" to go into fastboot or bootloader mode. In this mode you can type "fastboot flash recovery twrp.img" where the TWRP-xxx-xxxx.img has to be renamed into TWRP.img before hand (else you have to type the full TWRP file name. The TWRP file has to be in the same directory as the adb folder
I'm good turns out I ended up using my old PC, was able to adb recovery mode, installed 19.2 magisk over 18.1, which then showed up as being installed on the phone and root working. Guess I'll be keeping my old puter around for a while...lol
Related
Ok, so I rooted my LGOG E970. I figured I better unlock it as well, so I used FreeGee and unlocked it. I tried to download CWM but it said it couldnt download file. So I thought I would reboot my phone. Now, all I get is the google logo, with the unlocked key underneath, and it then goes to the LG logo and back to Google and shuts off. I tried to hold down power and volume down, nothing, and power volume up nothing.:crying:
any ideas? Thanks in advance! I love this phone!
CJ
You too, huh?
I did this the other night, and when the CWM failed to install I went to download it myself... That's when I saw that CWM for geeb is 6.0.3.8, not 6.0.4.5 like FreeGee shows. (Looks like FreeGee has moved on to targeting G2 or another... Oops.)
I hope you backed up your EFS, because mine was screwed up and I needed to manually restore it from the backup I'd taken. (I've had my phone rooted for 9+ months, finally got fed up with stock and was looking to get onto a 4.4 ROM)
So here's what I did:
Held power button until phone was properly off (failed boot seemed to be a still partially on state)
Held volumn up first, then started holding power.
When phone vibrated slightly, I let go of power and kept holding volume up... You should be in boot loader now.
When your phone is in the bootloader, connect to your PC (Make sure you have the proper drivers if you use Windows; I use Linux which doesn't have the same nonsense setup for drivers like Windows does)
Make sure "fastboot devices" shows your phone and then type: fastboot flash recovery _____recovery file name.img____
Press volume down twice to select "Recovery", and press power once to select it... You should be booted into the recovery that you just installed.
Once you're in a recovery, you can push a ROM zip via ADB, flash, wipe data/dalvik cache and reboot.
thanks, Just a little more help
aedren said:
You too, huh?
I did this the other night, and when the CWM failed to install I went to download it myself... That's when I saw that CWM for geeb is 6.0.3.8, not 6.0.4.5 like FreeGee shows. (Looks like FreeGee has moved on to targeting G2 or another... Oops.)
I hope you backed up your EFS, because mine was screwed up and I needed to manually restore it from the backup I'd taken. (I've had my phone rooted for 9+ months, finally got fed up with stock and was looking to get onto a 4.4 ROM)
So here's what I did:
Held power button until phone was properly off (failed boot seemed to be a still partially on state)
Held volumn up first, then started holding power.
When phone vibrated slightly, I let go of power and kept holding volume up... You should be in boot loader now.
When your phone is in the bootloader, connect to your PC (Make sure you have the proper drivers if you use Windows; I use Linux which doesn't have the same nonsense setup for drivers like Windows does)
Make sure "fastboot devices" shows your phone and then type: fastboot flash recovery _____recovery file name.img____
Press volume down twice to select "Recovery", and press power once to select it... You should be booted into the recovery that you just installed.
Once you're in a recovery, you can push a ROM zip via ADB, flash, wipe data/dalvik cache and reboot.
Click to expand...
Click to collapse
I try to go to recovery and it just goes blank. What program with my crazy windows would be best to get a stock file to the phone? Or any other ideas>
thanks again
ZombieGeek said:
I try to go to recovery and it just goes blank. What program with my crazy windows would be best to get a stock file to the phone? Or any other ideas>
thanks again
Click to expand...
Click to collapse
Yeah, the stock recovery won't boot if you try it either. I forgot to tell you that. If you drop in a custom recovery (TWRP or CWM), it will work fine and you can both create a backup of your data and flash a new ROM...
If you want to try to get back to stock, LGNPST is what you should try. But to be completely honest, I don't know if you can LGNPST from the state that it's in. I haven't tried, and I'm using a custom ROM now (the whole reason I unlocked the bootloader to begin with).
bummer
aedren said:
Yeah, the stock recovery won't boot if you try it either. I forgot to tell you that. If you drop in a custom recovery (TWRP or CWM), it will work fine and you can both create a backup of your data and flash a new ROM...
If you want to try to get back to stock, LGNPST is what you should try. But to be completely honest, I don't know if you can LGNPST from the state that it's in. I haven't tried, and I'm using a custom ROM now (the whole reason I unlocked the bootloader to begin with).
Click to expand...
Click to collapse
again, thanks so much! you are my hero, only problem is, I loaded the kit kat bu houstonn and now I have no cellular? I hate it when your phone isnt a phone lol
ZombieGeek said:
again, thanks so much! you are my hero, only problem is, I loaded the kit kat bu houstonn and now I have no cellular? I hate it when your phone isnt a phone lol
Click to expand...
Click to collapse
Yeah, I got that too. I don't know if I got it fixed due to changing ROM, using the suggested recovery from the ROM, or if it was due to me restoring my EFS backup.
I flashed the TeamWin recovery found in the PSX instructions. Then I flashed PSX + Latest kernel + Banks Gapps + Banks Google Camera + AT&T NFC fix + SuperSU. I manually restored EFS from an ADB shell while in recovery.
When I booted I had: LTE works, Wifi works, NFC works, Camera works, ART works... The only things failing for me are the following:
Cell provider shows up as "Maritime" (display bug; as mentioned, LTE works fine and I'm on AT&T)
Settings > Developer Tools > Geeky Process Stats (does nothing)
Settings > Lockscreen > Slider Shortcuts (crashes as soon as I tap the middle ring)
LogCat is spammed with "QCOM PowerLock: Failed to acquire lock" whenever my finger is on the screen.
/system/xbin/mount --bind doesn't work (neither does mount -o bind). It gets sorta half-way-there, because the target directory can't be removed, but isn't bound properly it seems.
Other than that, it's been fast and smooth.
alright guys, so here's the story. just yesterday i bought a brand new lg v10, got it home and the first thing i did was root the device and used ADB to load TWRP following the instructions here on SDA to a T for the ROOT/RECOVERY setup. and it worked. all was fine and dandy, the first time i booted into TWRP via ADB after root i got in, flashed a debloated ROM + xposed and again, everything went fine.. loaded into the OS of the new ROM, went through setup, turned on USB debugging, clicked always allow this computer, installed xposed app yadayadayada. I then, using ADB again, loaded into TWRP. i created a backup there just in case something went wrong with the changes i was about to make and once the backup was complete i loaded back in to the OS. at this point i thought i had done everything right and was confident that if i made system changes that didn't work out i could just flash the phone with TWRP from the backup i made. right? WRONG! ...apparently... so anyways, i made my first change, which was to use a NONROOT app called texdroider or whatever to change my DPI (as i have done with a couple phones previously without much issue) but i didn't take into account that stupid second screen... making the DPI changes system wide, as i'm sure those of you that know this phone are aware, causes the systemUI to crash with an error.. making the OS unusable.. so i tried to load into TWRP by holding the volume down and power button.. but instead it just booted me to the factory recovery.. not TWRP... the phone is unusable within the OS, i can't get the phone to connect to adb to boot into twrp as i had previously, i can't seem to get the phone into download mode, and i can't boot to TWRP and the OS is junk at this point.. but it DOES say on the "LG" screen that the bootloader is unlocked so i'm really hoping i'm not completely out of luck.. but i am not sure what to do at this point. does anyone here know of anything i can try to get into a custom recovery at this point? if i could get into TWRP my SD card in the phone has a backup, the original image, not to mention i could pull the SD card and add anything i need via my pc and then boot back to twrp etc etc and i would have no issue fixing the phone... i really don't understand what i did wrong or why i can't boot to my custom recovery but i'm at a loss.. i'm just looking for a way to force the phone into a custom recovery... or restore the original factory image.. if you have any advice at all i would really appreciate it.
Thanks for reading
**UPDATE** this may or may not make things much easier... but I got download mode working!! so at least there's that, still no custom recovery and i'm currently looking for a KDZ or TOT file to flash via lg flash tool... hopefully that makes things easier..
When you say you got to the factory recovery, what was that, an Android on its side or something asking you to factory reset your device? If it was the factory reset screen, if you select yes and then yes, it will take you to TWRP if you have it installed. If you don't it will factory reset your device.
ngoblirsch said:
**UPDATE** this may or may not make things much easier... but I got download mode working!! so at least there's that, still no custom recovery and i'm currently looking for a KDZ or TOT file to flash via lg flash tool... hopefully that makes things easier..
Click to expand...
Click to collapse
To boot into recovery from power off, you hold volume down & power. When you see the LG logo release and press power while continuing to hold volume down. Then as said above, it come up as a factory reset, select yes each time, and it should boot into twrp, providing you installed it correctly.
Sent from my LG-H901 using Tapatalk
YrrchSebor said:
When you say you got to the factory recovery, what was that, an Android on its side or something asking you to factory reset your device? If it was the factory reset screen, if you select yes and then yes, it will take you to TWRP if you have it installed. If you don't it will factory reset your device.
Click to expand...
Click to collapse
it was a screen asking me to do a factory reset, i click yes, it asks to confirm, i click yes again and then it "successfully" factory resets my phone... it shows the android factory reset symbol that its resetting, then says that its "optimizing apps" and goes through that whole process.. but when it finally loads the "welcome" screen (so i know for a fact that some sort reset has taken place) i get the same "systemui has crashed" error and the OS is unusable and won't connect to my computer.. idk why i can't access TWRP.. i booted to it 3 times before this happened, though never by the hardware buttons on the phone.. everytime i booted to TWRP i had used ADB to boot to TWRP.. what makes me the most sad is that i have a nandroid backup on my SD card... but i can't flash it without recovery.. which i can't install on the phone without getting into the OS..
is there any way to install TWRP or even boot to a temporary TWRP so that i can do so? if i can flash my nandroid i'm saved.. if i can get into a custom recovery i'm saved.. if i can find a .kdz file to flash, i'm saved... if i can get my phone to be recognized by my computer/adb i'm saved.... there simply has to be a way to unbrick this phone...
ZDeuce2 said:
To boot into recovery from power off, you hold volume down & power. When you see the LG logo release and press power while continuing to hold volume down. Then as said above, it come up as a factory reset, select yes each time, and it should boot into twrp, providing you installed it correctly.
Sent from my LG-H901 using Tapatalk
Click to expand...
Click to collapse
well i seem to have somehow NOT installed TWRP correctly because it just proceeds to factory reset my phone.. which for some odd reason doesn't reset the DPI... leaving me stranded... is there any way to get ADB to see my device in its present state? my computer makes the device recognition noise when i enter download mode and i can see it in device manager but not my computer or ADB
I've had this phone just over 2 months but I'm not positive, is download mode the same as the bootloader on this device? If so, fastboot commands should work, and you can flash TWRP again, or do 'fastboot boot TWRP_filename' and it will boot TWRP temporarily.
Oh, and the factory reset just wipes your data, but otherwise doesn't restore your system to factory state. That's why your dpi change remained.
YrrchSebor said:
I've had this phone just over 2 months but I'm not positive, is download mode the same as the bootloader on this device? If so, fastboot commands should work, and you can flash TWRP again, or do 'fastboot boot TWRP_filename' and it will boot TWRP temporarily.
Oh, and the factory reset just wipes your data, but otherwise doesn't restore your system to factory state. That's why your dpi change remained.
Click to expand...
Click to collapse
dude.. then what good is a factory reset?!? like seriously... and yeah, i tried that but i can't get adb to connect in download mode.. the device doesn't show up when I type "adb devices" like it did when i first rooted it. ... and i thought i followed the instructions exactly as it was laid out from this link.
http://forum.xda-developers.com/tmobile-lg-v10/general/guide-how-to-root-lg-v10-easy-t3274699
i think somewhere in there i must have missed something and ended up only booting into twrp temporarily.. which is certainly possible since i never boot to twrp during that initial process from the hardware keys or soft keys.. always through adb.. the phone was already plugged in.. typing the command was a couple keys away..
is there anyway to get TWRP on to the phone now? or am i screwed :'(
Well, it is a factory restore for the average user, because the average person isn't modifying their system. But no, I'm sure you're not screwed. If you're in the bootloader you can't use adb, you're already past that step, so you can skip to the fastboot part. What happens when you type fastboot devices? If the phone shows up then you can either fastboot flash or boot TWRP..
YrrchSebor said:
Well, it is a factory restore for the average user, because the average person isn't modifying their system. But no, I'm sure you're not screwed. If you're in the bootloader you can't use adb, you're already past that step, so you can skip to the fastboot part. What happens when you type fastboot devices? If the phone shows up then you can either fastboot flash or boot TWRP..
Click to expand...
Click to collapse
from what screen should i be attempting this? hold volume up with phone off and plug in to computer to enter download mode? should i try it at the factory reset screen (volume down plus power)? those are the only two screens i seem to have access to.. in download mode my pc/adb just doesn't recognize the phone.. it doesn't show up as a proper device like it did before this whole thing and in that factory reset mode i get nothing.. the download mode seems like its built for LG and runs from different drivers because in device manager it shows up with an error code that it couldn't start the device (this was not the case when i was using adb to unlock the bootloader and then using the bootloader to boot to TWRP..) what am i missing?
and hey, thank you so very much for taking time out of your day to help me. I really do appreciate it.
ngoblirsch said:
from what screen should i be attempting this? hold volume up with phone off and plug in to computer to enter download mode? should i try it at the factory reset screen (volume down plus power)? those are the only two screens i seem to have access to.. in download mode my pc/adb just doesn't recognize the phone.. it doesn't show up as a proper device like it did before this whole thing and in that factory reset mode i get nothing.. the download mode seems like its built for LG and runs from different drivers because in device manager it shows up with an error code that it couldn't start the device (this was not the case when i was using adb to unlock the bootloader and then using the bootloader to boot to TWRP..) what am i missing?
and hey, thank you so very much for taking time out of your day to help me. I really do appreciate it.
Click to expand...
Click to collapse
No problem buddy, and sorry for the confusion. You want to be on the bootloader screen, so here is what you can do: turn the phone off(or remove the battery if you have to, and put it back in), plug the usb cable into the computer only(not phone), hold volume down on phone, plug the usb cable into the phone. That should get you into the bootloader, and then you should be able to fastboot flash or fastboot boot TWRP.
Waiting for a resolution to this thread!
I'm pulling for you from the cheering section. (otherwise known as afraid to do it myself section!)
I'm pretty sure others have come through this exact situation unharmed (I've pretty much read every thread here.) so it's only a matter of time before you get this figured out.
Here's hoping it's sooner than later.
Sorry I can't offer more besides encouragement!
Sent from my pretty nifty brand new LG V10
ngoblirsch said:
from what screen should i be attempting this? hold volume up with phone off and plug in to computer to enter download mode? should i try it at the factory reset screen (volume down plus power)? those are the only two screens i seem to have access to.. in download mode my pc/adb just doesn't recognize the phone.. it doesn't show up as a proper device like it did before this whole thing and in that factory reset mode i get nothing.. the download mode seems like its built for LG and runs from different drivers because in device manager it shows up with an error code that it couldn't start the device (this was not the case when i was using adb to unlock the bootloader and then using the bootloader to boot to TWRP..) what am i missing?
and hey, thank you so very much for taking time out of your day to help me. I really do appreciate it.
Click to expand...
Click to collapse
Hold volume down and plug the cable in, already have completed in terminal.....
Sent from my LG-H901 using Tapatalk
YrrchSebor said:
No problem buddy, and sorry for the confusion. You want to be on the bootloader screen, so here is what you can do: turn the phone off(or remove the battery if you have to, and put it back in), plug the usb cable into the computer only(not phone), hold volume down on phone, plug the usb cable into the phone. That should get you into the bootloader, and then you should be able to fastboot flash or fastboot boot TWRP.
Click to expand...
Click to collapse
planetbeen said:
Waiting for a resolution to this thread!
I'm pulling for you from the cheering section. (otherwise known as afraid to do it myself section!)
I'm pretty sure others have come through this exact situation unharmed (I've pretty much read every thread here.) so it's only a matter of time before you get this figured out.
Here's hoping it's sooner than later.
Sorry I can't offer more besides encouragement!
Sent from my pretty nifty brand new LG V10
Click to expand...
Click to collapse
ZDeuce2 said:
Hold volume down and plug the cable in, already have completed in terminal.....
Sent from my LG-H901 using Tapatalk
Click to expand...
Click to collapse
@ngoblirsch Along with the information provided in these suggestions and what you have said, you need to reinstall your LG/fastboot drivers on your PC while in fastboot mode
YrrchSebor said:
No problem buddy, and sorry for the confusion. You want to be on the bootloader screen, so here is what you can do: turn the phone off(or remove the battery if you have to, and put it back in), plug the usb cable into the computer only(not phone), hold volume down on phone, plug the usb cable into the phone. That should get you into the bootloader, and then you should be able to fastboot flash or fastboot boot TWRP.
Click to expand...
Click to collapse
OH DEAR GOD THANK YOU!!!!
I spent all damn day yesterday trying to figure out how to get to the bootloader on this phone.. everything i read online said to hold volume down PLUS power while plugging it in and it was NOT working lmao. dude, thank you so much. after i read that comment here it took me about 30 seconds to connect to adb and boot to TWRP. This thread can be listed as RESOLVED!
Thanks again!! can't wait to start tweaking this awesome phone!
planetbeen said:
Waiting for a resolution to this thread!
I'm pulling for you from the cheering section. (otherwise known as afraid to do it myself section!)
I'm pretty sure others have come through this exact situation unharmed (I've pretty much read every thread here.) so it's only a matter of time before you get this figured out.
Here's hoping it's sooner than later.
Sorry I can't offer more besides encouragement!
Sent from my pretty nifty brand new LG V10
Click to expand...
Click to collapse
Well I appreciate the encouragement, it sure seems to have helped! Issue has been resolved. ended up that i just didn't know the hardware key combination to get to the bootloader/fastboot mode without being already connected to adb. nothing that i could find online said to hold volume down while plugging it in to a computer. as soon as i was able to do so i connected to adb and it was a breeze from there; I am now back with an OS AND a customer recovery properly installed on the device!! I will be hanging around these forums for as long as i have this phone so i'm sure i'll bump into you guys! absolutely love the community here on XDA, you guys are freaking awesome!!
ngoblirsch said:
OH DEAR GOD THANK YOU!!!!
I spent all damn day yesterday trying to figure out how to get to the bootloader on this phone.. everything i read online said to hold volume down PLUS power while plugging it in and it was NOT working lmao. dude, thank you so much. after i read that comment here it took me about 30 seconds to connect to adb and boot to TWRP. This thread can be listed as RESOLVED!
Thanks again!! can't wait to start tweaking this awesome phone!
Click to expand...
Click to collapse
Glad you got it fixed, and welcome to the V10 device and forums!
Hello everybody,
since saturday I have a really big problem. Until now I tried to find a similar problem from an other person in the internet in order to fix mine but that was not possible.
So in my last hope I am now writing it down here. Hopefully someone can help me:
The phone was/is rooted and has TWRP as recovery installed (v3.21). The software is still the original EMUI.
On saturday my Huawei Honor 5x (Model KIW-L21) gave me the notification that there is an software update avaible. So I backuped everything with TWRP to my sd-card and copied it to the computer. After this I ran th eupdate. The update downloaded the new software, then rebootet to the recovery, installed the update.zip automaticly and rebootet again. Then there was written on the screen "Huawei software installing ... DO NOT unplug usb or press any key!". Also there was "0%" all the time. It did nothing. also the phone was not connected with usb.
After an hour I long pressed the power button. after two seconds there was the text "Warning: The powerkey is long pressed, please release powerkey to avoid system crash" displayed. I pressed it longer and the phone turned off.
Now I have the following problem. When the phone is turned off, I can:
press the power button: the phone starts, the "honor ... android" logo is shown but nothing more happens. ("fastboot devices" -> no devices found, "adb devices" -> device found but no permission to enter commands)
press the power button and the volume up button and the volume down button at the same time: normally this should take me in the recovery mode, mut it doesn't anymore. Instead the "EMUI" update screen is shown (see above "huawei software installing ..." with "0%") ("fastboot devices" -> no devices found, "adb devices" -> no devices found)
press the power button and the volume up button at the same time: I get a huawei menu with three buttons: "reboot", "wipe user cache" and "factory reset". I tried both (wipe and reset) wich both finished without an error. But nothing changes ("fastboot devices" -> no devices found, "adb devices" -> no devices found)
press the power button and the volume down button at the same time: I get an "eRecovery" menu from huawei with three buttons: "Reboot", "power off" and "Recover with latest software". The last button lets me connect to my wifi and then "searching for packages", with failes all the time. ("fastboot devices" -> no devices found, "adb devices" -> no devices found)
This problem occures with and also without the sd-card. Also there is no "update.zip" or "update.app" on the sd-card.
I really hope somebody can help me. I only need to get into the recovery. If I am there I can recover the backup or install a new ROM. That would be no problem for me. But at the moment I get nothing :crying:
Or maybe a tool to reset the phone completly? to start over from the beginning?
greetings,
Christopher
PS.: Thanks for your efford.
PSS.: Sorry for my bad english, I really try my best and hope that you understand what I am trying to say.
Same problem here... Please help us :'(
christopher2007 said:
Hello everybody,
since saturday I have a really big problem. Until now I tried to find a similar problem from an other person in the internet in order to fix mine but that was not possible.
So in my last hope I am now writing it down here. Hopefully someone can help me:
The phone was/is rooted and has TWRP as recovery installed (v3.21). The software is still the original EMUI.
On saturday my Huawei Honor 5x (Model KIW-L21) gave me the notification that there is an software update avaible. So I backuped everything with TWRP to my sd-card and copied it to the computer. After this I ran th eupdate. The update downloaded the new software, then rebootet to the recovery, installed the update.zip automaticly and rebootet again. Then there was written on the screen "Huawei software installing ... DO NOT unplug usb or press any key!". Also there was "0%" all the time. It did nothing. also the phone was not connected with usb.
After an hour I long pressed the power button. after two seconds there was the text "Warning: The powerkey is long pressed, please release powerkey to avoid system crash" displayed. I pressed it longer and the phone turned off.
Now I have the following problem. When the phone is turned off, I can:
press the power button: the phone starts, the "honor ... android" logo is shown but nothing more happens. ("fastboot devices" -> no devices found, "adb devices" -> device found but no permission to enter commands)
press the power button and the volume up button and the volume down button at the same time: normally this should take me in the recovery mode, mut it doesn't anymore. Instead the "EMUI" update screen is shown (see above "huawei software installing ..." with "0%") ("fastboot devices" -> no devices found, "adb devices" -> no devices found)
press the power button and the volume up button at the same time: I get a huawei menu with three buttons: "reboot", "wipe user cache" and "factory reset". I tried both (wipe and reset) wich both finished without an error. But nothing changes ("fastboot devices" -> no devices found, "adb devices" -> no devices found)
press the power button and the volume down button at the same time: I get an "eRecovery" menu from huawei with three buttons: "Reboot", "power off" and "Recover with latest software". The last button lets me connect to my wifi and then "searching for packages", with failes all the time. ("fastboot devices" -> no devices found, "adb devices" -> no devices found)
This problem occures with and also without the sd-card. Also there is no "update.zip" or "update.app" on the sd-card.
I really hope somebody can help me. I only need to get into the recovery. If I am there I can recover the backup or install a new ROM. That would be no problem for me. But at the moment I get nothing :crying:
Or maybe a tool to reset the phone completly? to start over from the beginning?
greetings,
Christopher
PS.: Thanks for your efford.
PSS.: Sorry for my bad english, I really try my best and hope that you understand what I am trying to say.
Click to expand...
Click to collapse
suzushima said:
Same problem here... Please help us :'(
Click to expand...
Click to collapse
to enter fastboot mode
1. Place the device in fastboot mode:
Turn off the device. (then wait for at least 2 seconds) For a mobile phone, press and hold the volume down and power keys simultaneously for at least 10 seconds (for a tablet, press and hold the volume up and power keys).
2. If the above operations do not switch the device to fastboot mode, please try the following steps:
Turn off the device. (then wait for at least 2 seconds) Then insert the USB cable and press and hold the volume down and power keys simultaneously for at least 10 seconds.
Step 2 worked for me every time
Arobase40 said:
AGAIN AND AGAIN, when you receive an update notification you MUST first flash back to stock recovery or it won't update with TWRP !!!
- To recover a stock recovery you need to boot onto download mode/your bootloader mode (Power+Volume Down) : plug your phone to your computer and type "fastboot flash recovery recovery.img".
From there you will loose your connexion with your computer. So unplug your phone and reboot manually holding down the Power button for some seconds.
If the system ever update your phone, BE VERY PATIENT !
The above note should probably part of a sticky !!!
If you don't get back to your Home screen and if you need TWRP back, reboot again onto download mode/your bootloader mode (Power+Volume Down) : plug your phone to your computer and type "fastboot flash recovery twrp.img" (or whatever the custom recovery name).
Click to expand...
Click to collapse
The problem a lot of people were having is TWRP flashed enough of the update that they lost custom recovery and had no way to get to the bootloader / fastboot ... that's why I posted the instructions above and in about 4 other threads.
Did you ever get your phone updated ?
Arobase40 said:
AGAIN AND AGAIN, when you receive an update notification you MUST first flash back to stock recovery or it won't update with TWRP !!!
Click to expand...
Click to collapse
I did not knew this one. Thanks a lot.
Thanks to @clsA I found the stock recovery here and I will try it:
https://www.androidfilehost.com/?w=files&flid=49383
clsA said:
1.Turn off the device. (then wait for at least 2 seconds) For a mobile phone, press and hold the volume down and power keys simultaneously for at least 10 seconds (for a tablet, press and hold the volume up and power keys).
2. If the above operations do not switch the device to fastboot mode, please try the following steps:
Turn off the device. (then wait for at least 2 seconds) Then insert the USB cable and press and hold the volume down and power keys simultaneously for at least 10 seconds.
Click to expand...
Click to collapse
Working great thanks a lot!
"fastboot & rescue mode" with a working usb connection.
What is the next step? If I now flash the stock recovery, does the phone manages to finish the system update?
Or should I flash the twrp recovery and not the stock revocery?
greetings,
Christopher
EDIT:
I flashed the stock recovery and also the twrp recovery. both times i startet the phone and hoped the installation of the new software will go on. But it didn't.
So my problem is still resistant. so what can I do? How do I stop the update from blocking my recovery? I do not need the update. maybe I can reset my device with the fastboot access somehow?
christopher2007 said:
I did not knew this one. Thanks a lot.
Thanks to @clsA I found the stock recovery here and I will try it:
https://www.androidfilehost.com/?w=files&flid=49383
Working great thanks a lot!
"fastboot & rescue mode" with a working usb connection.
What is the next step? If I now flash the stock recovery, does the phone manages to finish the system update?
Or should I flash the twrp recovery and not the stock revocery?
greetings,
Christopher
EDIT:
I flashed the stock recovery and also the twrp recovery. both times i startet the phone and hoped the installation of the new software will go on. But it didn't.
So my problem is still resistant. so what can I do? How do I stop the update from blocking my recovery? I do not need the update. maybe I can reset my device with the fastboot access somehow?
Click to expand...
Click to collapse
All the full updates are in the file depot
Use stock recovery plus the full update for your version.
You have to hold volup + voldown + power to start the update
Refresh TWRP / Root and your good to go
Sent from my KIW-L24 using Tapatalk
clsA said:
All the full updates are in the file depot
Use stock recovery plus the full update for your version.
You have to hold volup + voldown + power to start the update
Refresh TWRP / Root and your good to go
Click to expand...
Click to collapse
I found the stock recovery at https://www.androidfilehost.com/?w=files&flid=51004 but I have no idea what update I must use and how to use it.
Could you please give me a concrete link with a little introduction? Do I have to copy the update file to my sd-card? or do I have to use the "fastboot update *" command?
(Most of the files are for "KIW-L24" but I have a "KIW-L21" ... is there a significant difference? Od do I can use also the other files?)
Also, don't I have to stop the wrong update first?
greetings,
Christopher
EDIT:
I tried these "UPDATE.APP":
http://forum.xda-developers.com/honor-5x/development/stock-kiw-l24-l21-t3312684
http://www.androidvillaz.com/2016/0...honor-5x-to-stock-lollipop-firmware-b130.html
both did not work. I copied them into the "dload" folder in the root of the sd-card and started the phone with volup+coldown+power.
The only thing the phone said was "Software install failed! ... Press powerkey to conrifm ... Shutdown system now".
christopher2007 said:
I found the stock recovery at https://www.androidfilehost.com/?w=files&flid=51004 but I have no idea what update I must use and how to use it.
Could you please give me a concrete link with a little introduction? Do I have to copy the update file to my sd-card? or do I have to use the "fastboot update *" command?
(Most of the files are for "KIW-L24" but I have a "KIW-L21" ... is there a significant difference? Od do I can use also the other files?)
Also, don't I have to stop the wrong update first?
greetings,
Christopher
EDIT:
I tried these "UPDATE.APP":
http://forum.xda-developers.com/honor-5x/development/stock-kiw-l24-l21-t3312684
http://www.androidvillaz.com/2016/0...honor-5x-to-stock-lollipop-firmware-b130.html
both did not work. I copied them into the "dload" folder in the root of the sd-card and started the phone with volup+coldown+power.
The only thing the phone said was "Software install failed! ... Press powerkey to conrifm ... Shutdown system now".
Click to expand...
Click to collapse
if the update.app doesn't work you'll have to flash TWRP and the Stock Rom and wait like everyone else that's stuck trying to update the L21
clsA said:
if the update.app doesn't work you'll have to flash TWRP and the Stock Rom and wait like everyone else that's stuck trying to update the L21
Click to expand...
Click to collapse
The only way I know to flash a ROM, is to go over TWRP.
So I now did the following:
Phone power off
connect to pc
voldown+power
in the fastboot flash the recovery from twrp
shutdown
copy the "customromtemplate-5x-plk21-b130-r3.zip" to the sd-card
volup+coldown+power what normally starts twrp, but only the huawei update manager is shown
I only need twrp, no update and nothing else.
What options do I have left, because "flash a ROM" is not working ...
How can I stop this terrible update that is blocking my twrp?
greetings,
Christopher
christopher2007 said:
The only way I know to flash a ROM, is to go over TWRP.
So I now did the following:
Phone power off
connect to pc
voldown+power
in the fastboot flash the recovery from twrp
shutdown
copy the "customromtemplate-5x-plk21-b130-r3.zip" to the sd-card
volup+coldown+power what normally starts twrp, but only the huawei update manager is shown
I only need twrp, no update and nothing else.
What options do I have left, because "flash a ROM" is not working ...
greetings,
Christopher
Click to expand...
Click to collapse
are you flashing TWRP ?
you enter recovery with Volume up and Power
in TWRP you choose Install then choose customromtemplate-5x-plk21-b130-r3.zip
swipe to flash when it's done reboot
and your rom should load
clsA said:
are you flashing TWRP ?
you enter recovery with Volume up and Power
in TWRP you choose Install then choose customromtemplate-5x-plk21-b130-r3.zip
swipe to flash when it's done reboot
and your rom should load
Click to expand...
Click to collapse
I flashed TWRP using "kiwi_twrp_3-21_recovery.img". I also used this one last time (one month ago) and it worked then and also now.
Flashing was successful, but when I press volup+power I get a huawei menu.
At the top there is the "EMUI" circle and below there are three buttons:
Reboot system now
Wipe data/factory reset
Wipe cache partition
I can move around in this little menu by using the volume keys.
But this is not TWRP.
And normally I enter the recovery by using volup+voldown+power. But this is currently blocked by the update progress from huawei.
greetings,
Christopher
christopher2007 said:
I flashed TWRP using "kiwi_twrp_3-21_recovery.img". I also used this one last time (one month ago) and it worked then and also now.
Flashing was successful, but when I press volup+power I get a huawei menu.
At the top there is the "EMUI" circle and below there are three buttons:
Reboot system now
Wipe data/factory reset
Wipe cache partition
I can move around in this little menu by using the volume keys.
But this is not TWRP.
And normally I enter the recovery by using volup+voldown+power. But this is currently blocked by the update progress from huawei.
greetings,
Christopher
Click to expand...
Click to collapse
You still have stock recovery
Flash TWRP -
fastboot flash recovery kiwi_twrp_3-21_recovery.img
Do not reboot the phone
Hold power plus volup and TWRP should load.
Now flash your rom
Sent from my KIW-L24 using Tapatalk
clsA said:
You still have stock recovery
Flash TWRP -
fastboot flash recovery kiwi_twrp_3-21_recovery.img
Do not reboot the phone
Hold power plus volup and TWRP should load.
Now flash your rom
Sent from my KIW-L24 using Tapatalk
Click to expand...
Click to collapse
C:\adb>fastboot flash recovery kiwi_twrp_3-21_recovery.img
target reported max download size of 266338304 bytes
sending 'recovery' (45196 KB)...
OKAY [ 1.442s]
writing 'recovery'...
OKAY [ 0.703s]
finished. total time: 2.148s
I now flashed this more then ten times ... but with power+volup I still get the EMUI menu.
christopher2007 said:
C:\adb>fastboot flash recovery kiwi_twrp_3-21_recovery.img
target reported max download size of 266338304 bytes
sending 'recovery' (45196 KB)...
OKAY [ 1.442s]
writing 'recovery'...
OKAY [ 0.703s]
finished. total time: 2.148s
I now flashed this more then ten times ... but with power+volup I still get the EMUI menu.
Click to expand...
Click to collapse
Are you rebooting from the fastboot screen?
From the white boot loader screen hold volume up and power for 15 seconds
Sent from my KIW-L24 using Tapatalk
clsA said:
Are you rebooting from the fastboot screen?
From the white boot loader screen hold volume up and power for 15 seconds
Click to expand...
Click to collapse
The last six hours I tried to fix my phone ... again. One thing I did really helped a little:
Target1920 said:
http://forum.android.com.pl/topic/205126-instalacjaodzyskiwanie-systemu-rom-za-pomoca-fastboot/
This is the polish version of manual, I will write you how to do it:
1. Download ADB and Fastboot
2. Extract to c:/adb
3. Download from this thread firmware for you (extracted version!) http://forum.xda-developers.com/honor-5x/development/stock-kiw-l24-l21-t3312684 If you have problem what firmware you have to install, take look at the back side of phone, at the down you will se KIW-L21 or 24 (or another). Copy all files to adb folder
4. Rund adb program
5. Write in the command line: cd c:/adb
6. Connect phone to usb to download mode (power and vol- combination)
7. Write in fastboot command: fastboot flash recovery recover.img (or recovrey .img, see the file and type it name) - wait for install
8. And now: If the flash is succesfull, reboot the phone to recovery (power and volume+) and wipe all data. Phone have to work.
But if flash is not succesfull, plug again usb with download mode
9. Write this commands: fastboot flash cust cust.img -wait for install
and: fastboot flash system system.img -also wait, system.img can took a while
10. Now you will enter recovery and wipe all data
11. Again plug usb cable and install firmware with those commands:
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash cache cache.img
fastboot flash userdata userdata.img
fastboot flash system system.img
Click to expand...
Click to collapse
With this I am not able to start my phone again. It will boot normally and I have a clean android. No userdata and no root.
So I now did the same like last month:
Unlock OEM -> not necessary, because it is already unlocked
install twrp with fastboot
reboot to twrp and there it is again
I did exactly what you said and also I did exactly the same thing I did last month but both times there is the same result: TWRP will not show up.
The "stock recovery" is blocking twrp in some sort of way. I can do whatever I whant ... volup+power out of the fastbook mode, or with "adb reboot recovery", or other ways ... twrp will not show up.
How is this possible? I also tried different twrp images. (The "kiwi_twrp_2-27_recovery.img" and "kiwi_twrp_3-21_recovery.img" out of your repository, and also the "twrp-3.0.0-0-kiwi.img" and "twrp-3.0.2-0-kiwi.img" from the twrp website itself ... always the same result: no twrp)
I am really at the end of my knollage
greetings,
Christopher
christopher2007 said:
The last six hours I tried to fix my phone ... again. One thing I did really helped a little:
With this I am not able to start my phone again. It will boot normally and I have a clean android. No userdata and no root.
So I now did the same like last month:
Unlock OEM -> not necessary, because it is already unlocked
install twrp with fastboot
reboot to twrp and there it is again
I did exactly what you said and also I did exactly the same thing I did last month but both times there is the same result: TWRP will not show up.
The "stock recovery" is blocking twrp in some sort of way. I can do whatever I whant ... volup+power out of the fastbook mode, or with "adb reboot recovery", or other ways ... twrp will not show up.
How is this possible? I also tried different twrp images. (The "kiwi_twrp_2-27_recovery.img" and "kiwi_twrp_3-21_recovery.img" out of your repository, and also the "twrp-3.0.0-0-kiwi.img" and "twrp-3.0.2-0-kiwi.img" from the twrp website itself ... always the same result: no twrp)
I am really at the end of my knollage
greetings,
Christopher
Click to expand...
Click to collapse
First off thanks for the very informative post.
Without actually having the phone in my hands I'm also stumped at what to try next.
After flashing TWRP and still in the boot loader unplug the USB before you reboot with power and volume up.
That's all I can think of right now
Sent from my KIW-L24 using Tapatalk
--
clsA said:
First off thanks for the very informative post.
Without actually having the phone in my hands I'm also stumped at what to try next.
After flashing TWRP and still in the boot loader unplug the USB before you reboot with power and volume up.
That's all I can think of right now
Sent from my KIW-L24 using Tapatalk
Click to expand...
Click to collapse
I must thank you for all your help
So I now read some more articles and tried some things. So there are old problems solved, but also new problems came up:
For me it is no longer possible to flash a recovery that is permanent. I have no idea why but I am ignoring it, because I can start the phone with voldown+power into bootloader and then use a usb-connection to enter the following command:
fastboot boot twrp-3.0.2-0-kiwi.img
Click to expand...
Click to collapse
So i can enter twrp temporary and because I do not need TWRP this often, that is ok for me.
BUT:
with the extracted "UPDATE.APP" and flashing some "*.img" files manually (see my last post), I have a more or less working "L21C432B130" version of android.
So now there is everything original (recovery, system, ...).
The update to "L21C432B140" is still not working. But that is also something I can live with.
So now I whant to restore my old system in order to have my old data/apps/... .
So I enter my temporary TWRP, go to Restore and select my old backup. Then the restore starts. Restoring EFS, Restoring efs2, Restoring Recovery, Wiping System and Formatting System using make_ext4fs. All of this in this order are successful. But the last operation "Restoring Data" failes with the following error message:
extractTarFork() process ended with error 255
Click to expand...
Click to collapse
So I searched on xda and found out, that this could be ANYTHING. I tried five or six different methods in order to fix it. In the end I am not sure what really fixxed it, but now I can restore my old update without any error. The phone now runs and I have all my old data.
There are four main differences on my phone to the time before I tried that damn update:
1. I have less internal storage
2. I have no TWRP permanently avaible
3. I can not Factory-Reset
4. I can not use a "UPDATE.APP" inside a "dload" folder on the sdcard
(the last two things always failes)
But as long as the android system now runs smooth again I can live with these things.
Is there maybe anything else I should be careful? maybe a known bug/problem that I have not seen yet?
The reason why I wanted to update in the first place was, that I have problems with my sd-card.
Some Apps do not allow to use the external storage. Easy Voice Recorder is the main problem. But also the Call Recorder has problems with it.
Is this a well known bug? Does a update helps? And if so, how do I update? (Now I know how to rescue my phone, so I could try it again xD )
Or does this problem gets solved with an custom ROM? If so, what good custom ROMs are out there for the honor 5x?
Or is this a problem that is not possible to fix on the honor 5x? Because these apps does not have this problem on my HTC One M9 ...
And thanks again so much for all your help
greetings,
Christopher
christopher2007 said:
I must thank you for all your help
So I now read some more articles and tried some things. So there are old problems solved, but also new problems came up:
For me it is no longer possible to flash a recovery that is permanent. I have no idea why but I am ignoring it, because I can start the phone with voldown+power into bootloader and then use a usb-connection to enter the following command:
So i can enter twrp temporary and because I do not need TWRP this often, that is ok for me.
BUT:
with the extracted "UPDATE.APP" and flashing some "*.img" files manually (see my last post), I have a more or less working "L21C432B130" version of android.
So now there is everything original (recovery, system, ...).
The update to "L21C432B140" is still not working. But that is also something I can live with.
So now I whant to restore my old system in order to have my old data/apps/... .
So I enter my temporary TWRP, go to Restore and select my old backup. Then the restore starts. Restoring EFS, Restoring efs2, Restoring Recovery, Wiping System and Formatting System using make_ext4fs. All of this in this order are successful. But the last operation "Restoring Data" failes with the following error message:
So I searched on xda and found out, that this could be ANYTHING. I tried five or six different methods in order to fix it. In the end I am not sure what really fixxed it, but now I can restore my old update without any error. The phone now runs and I have all my old data.
There are four main differences on my phone to the time before I tried that damn update:
1. I have less internal storage
2. I have no TWRP permanently avaible
3. I can not Factory-Reset
4. I can not use a "UPDATE.APP" inside a "dload" folder on the sdcard
(the last two things always failes)
But as long as the android system now runs smooth again I can live with these things.
Is there maybe anything else I should be careful? maybe a known bug/problem that I have not seen yet?
The reason why I wanted to update in the first place was, that I have problems with my sd-card.
Some Apps do not allow to use the external storage. Easy Voice Recorder is the main problem. But also the Call Recorder has problems with it.
Is this a well known bug? Does a update helps? And if so, how do I update? (Now I know how to rescue my phone, so I could try it again xD )
Or does this problem gets solved with an custom ROM? If so, what good custom ROMs are out there for the honor 5x?
Or is this a problem that is not possible to fix on the honor 5x? Because these apps does not have this problem on my HTC One M9 ...
And thanks again so much for all your help
greetings,
Christopher
Click to expand...
Click to collapse
from your current state you can try flash recovery with TWRP by choosing install / image / your version of TWRP / choose recovery / swipe to flash
Now choose reboot / recovery
As for the sdcard try the sdcard fix for kit Kat in the play store. It works for some older apps.
Sent from my KIW-L24 using Tapatalk
Arobase40 said:
If you mean getting my phone updated to KIW-L21 B140, no I still don't get it !
But I did try with KIW-L24 B151 with the result I already mentioned previously : almost bricked... ^^
But I always managed to get into Bootloader/Fastboot to flash back any kind of recovery...
Click to expand...
Click to collapse
clsA said:
All the full updates are in the file depot
Use stock recovery plus the full update for your version.
You have to hold volup + voldown + power to start the update
Refresh TWRP / Root and your good to go
Sent from my KIW-L24 using Tapatalk
Click to expand...
Click to collapse
So i have this issue too. im so stupid for doing this. I can go into fastboot mode and i flashed stock recovery and when i rebooted into recovery it still said that it was updating the firmware. I flashed twrp after that and it had the same message. am i doing something wrong or is it my phone? I tried rebooting into bootloader using adb but only fastboot will reconize my phone so adb also wont work. could you guys maybe help me?
Edit: Yessss. i got it using the temporary command. Thank you guys all for your help. it was so stupid of me to flash it with twrp still on it. Thank you all very much
I have an XT1526 from Freedompop. It came prerooted with TWRP installed, however SuperSU was removed. I tried to install SuperSU via Google Play, and after that the phone would not start. It would be stuck on the Moto logo. I tried to reinstall supersu via TWRP . I used this package:
SR1-SuperSU-v2.79-SR1-20161221223537.zip . The install went through, but the phone still does not start.
I tried to do something via adb/fastboot.
adb devices does not show the phone connected, however fastboot devices sees the phone connected.
fastboot reboot works too.
What should I do now?
Currently only bootloader and TWRP work. TWPR sees the content on the SD card
mzel said:
I have an XT1526 from Freedompop. It came prerooted with TWRP installed, however SuperSU was removed. I tried to install SuperSU via Google Play, and after that the phone would not start. It would be stuck on the Moto logo. I tried to reinstall supersu via TWRP . I used this package:
SR1-SuperSU-v2.79-SR1-20161221223537.zip . The install went through, but the phone still does not start.
I tried to do something via adb/fastboot.
adb devices does not show the phone connected, however fastboot devices sees the phone connected.
fastboot reboot works too.
What should I do now?
Currently only bootloader and TWRP work. TWPR sees the content on the SD card
Click to expand...
Click to collapse
Press and hold the power button on the boot animation screen until the phone is forced restarted again.... Do this until it boots completed
If the problem doesn't stop, try different version of SuperSU.... Also tell more about your ROM?
Assassin's Blood said:
Press and hold the power button on the boot animation screen until the phone is forced restarted again.... Do this until it boots completed
If the problem doesn't stop, try different version of SuperSU.... Also tell more about your ROM?
Click to expand...
Click to collapse
I have restarted the phone this way many times and it never comes past the logo. Also on the long press it does not shut down, it only restarts.
What is the version of SuperSU suitable for this phone?
I have not changed the ROM. It is whatever it came with. How can I check?
A
mzel said:
I have restarted the phone this way many times and it never comes past the logo. Also on the long press it does not shut down, it only restarts.
What is the version of SuperSU suitable for this phone?
I have not changed the ROM. It is whatever it came with. How can I check?
A
Click to expand...
Click to collapse
Check it in your settings or bootloader.... Turn off the phone and press down+ power simultaneously....
Assassin's Blood said:
Check it in your settings or bootloader.... Turn off the phone and press down+ power simultaneously....
Click to expand...
Click to collapse
With power+Volume up it goes to the Moto logo. With power+Volume Down it goes to the bootloader and shows some info. No word about the ROM. What is strange - baseband NULL.
I suppose it is some Boost ROM, but this is just my guess
Wiping the phone via TWRP and flashing the https://s3-us-west-2.amazonaws.com/supersu/download/zip/SuperSU-v2.79-201612051815.zip helped.
Thanks a lot!
I upgrade my phone to EMUI B330 (Android 6.0) and I used TWRP recovery to flashed Supersu 2.79. But after flashed and reboot, my phone cannot start up. It always blocks during starting (Always showing "Honor" logo). I cannot enter the system. How can I fix the problem?
did you use superSU V2.62? others dont work on honor 7
thelous said:
did you use superSU V2.62? others dont work on honor 7
Click to expand...
Click to collapse
Thank you very much! It works!!! I also found that SuperSU v2.64 is working, too!!!:good:
how you made it to start
Hi, i have the same issue, installed superSU 2.7, and cant go anyfurther,
how you were able to uninstall, and install the superSU 2.6
Thanks in advance
Nemo1981 said:
Hi, i have the same issue, installed superSU 2.7, and cant go anyfurther,
how you were able to uninstall, and install the superSU 2.6
Thanks in advance
Click to expand...
Click to collapse
you could use twrp file manager or flash over new sipersu i think....
thelous said:
you could use twrp file manager or flash over new sipersu i think....
Click to expand...
Click to collapse
Thanks for the reply,
I cant get to the twrp, when i press volumeup, the phone keep restarting,
what do you mean by "flash over new sipersu",
the problem, the phone keep restarting when i press VolumeUp+Down+power, then i release power, and keep pressing volumeUP+volumeDown,
but instead of going to twrp, the phone restart
Nemo1981 said:
Thanks for the reply,
I cant get to the twrp, when i press volumeup, the phone keep restarting,
what do you mean by "flash over new sipersu",
the problem, the phone keep restarting when i press VolumeUp+Down+power, then i release power, and keep pressing volumeUP+volumeDown,
but instead of going to twrp, the phone restart
Click to expand...
Click to collapse
let power go as soon as you see honor logo
still same
thelous said:
let power go as soon as you see honor logo
Click to expand...
Click to collapse
I did, once i sense the vibration, i let go the power, and keep pressing on the volumeUp+down buttons, but the same issue
even if i only press the volumeUp button, it also restart instead of going to the twrp folder,
is there is any software, or other way to access it via pc, or something,
Nemo1981 said:
I did, once i sense the vibration, i let go the power, and keep pressing on the volumeUp+down buttons, but the same issue
even if i only press the volumeUp button, it also restart instead of going to the twrp folder,
is there is any software, or other way to access it via pc, or something,
Click to expand...
Click to collapse
adb should work
adb not recognized on my computer anymore, cant see the phone, mtp driver not working anymore
but fastboot is working, i can see the mobile in fastboot mode
Nemo1981 said:
adb not recognized on my computer anymore, cant see the phone, mtp driver not working anymore
but fastboot is working, i can see the mobile in fastboot mode
Click to expand...
Click to collapse
You can enter the fastboot mode and then re-flash the TWRP. After that, you reboot the phone and keep pressing the volumeUP button while it's booting. So that you can enter the TWRP.
My method is that I enter TWRP and then use "Advantage Wipe" to wipe cache and davik cache. Then, flash v2.64 of SuperSU and reboot system. It works.
Nemo1981 said:
adb not recognized on my computer anymore, cant see the phone, mtp driver not working anymore
but fastboot is working, i can see the mobile in fastboot mode
Click to expand...
Click to collapse
You can enter fastboot mode to re-flash TWRP. After that, you can enter TWRP and wipe cache and davike cache. Finally, flash v2.64 and reboot system.
hello,
so the threat is called how to root honor 7......and you only write about the SuperSU issue, not about the procedure how to root it.
what is the solution for rooting the H7 with android 6.0 build 380?
The right files for doing it like TWRP, IMG aso.
THX