I've had a Bip for less than 24 hours and overnight the vibrations have stopped functioning. Notifications come through ok, but no vibration. I've factory reset, flashed different firmware, no joy. Anyone seen this? Am I out of luck?
betarayjim said:
I've had a Bip for less than 24 hours and overnight the vibrations have stopped functioning. Notifications come through ok, but no vibration. I've factory reset, flashed different firmware, no joy. Anyone seen this? Am I out of luck?
Click to expand...
Click to collapse
Same to me... anyone could fix this fail on bip?
Enviado desde mi SM-N950F mediante Tapatalk
Same to me ...
Have you got any response ?
Same for me since 1 Month...
No vibrations for all specifications (alarm, notifications...).
Hard reset without effect unfortunately...
As if the vibrator engine is dead...
Related
I have bought an amazfit bip watch some times a go and it was working very good.
Except for the button, a couple of months ago the button stopped working. It only works rarely bu pushing a much harder. I didn't dropped it from my hand or something. using only mi fit application.
So far I have tried, reset app, factory reset. Install app etc. Full charge.
I don't want to open the watch. Are there similar issues to anyone who is using.
Maybe there is outthere some software solution, at least to wake whatch from app only, as button is not working anymore.
mexiro said:
I have bought an amazfit bip watch some times a go and it was working very good.
Except for the button, a couple of months ago the button stopped working. It only works rarely bu pushing a much harder. I didn't dropped it from my hand or something. using only mi fit application.
So far I have tried, reset app, factory reset. Install app etc. Full charge.
I don't want to open the watch. Are there similar issues to anyone who is using.
Maybe there is outthere some software solution, at least to wake whatch from app only, as button is not working anymore.
Click to expand...
Click to collapse
Most likely this is a hardware problem.
In my watch, button working well one year now.
Hi,
I'm facing a strange issue on Redmi Note 3 (SD) for past couple of weeks. The display suddenly turns blank, while all other things are functioning. If I try to turn off and turn on the display immediately, the screen remains blank. However, the problem automatically resolves itself after a few mins. I thought this could be due to heating, so I cleared up a lot of storage space and uninstalled all unnecessary apps. The problem still persists.
It is completely random. The display will suddenly turn blank, and will be back to normal if I unlock after a few mins. This is really frustrating. The things I've tried (and failed) include:
Removing and reattaching the cable connected to the display port
Cleaning the entire board
Storage cleanup
Battery optimizations
Temperature oversight
Has anyone else faced similar issue? Are you aware of any solutions?
BlasFamous said:
Hi,
I'm facing a strange issue on Redmi Note 3 (SD) for past couple of weeks. The display suddenly turns blank, while all other things are functioning. If I try to turn off and turn on the display immediately, the screen remains blank. However, the problem automatically resolves itself after a few mins. I thought this could be due to heating, so I cleared up a lot of storage space and uninstalled all unnecessary apps. The problem still persists.
It is completely random. The display will suddenly turn blank, and will be back to normal if I unlock after a few mins. This is really frustrating. The things I've tried (and failed) include:
Removing and reattaching the cable connected to the display port
Cleaning the entire board
Storage cleanup
Battery optimizations
Temperature oversight
Has anyone else faced similar issue? Are you aware of any solutions?
Click to expand...
Click to collapse
Answer the following.
What rom?
What gapps?
What twrp version?
What phone? Kenzo or kate?
Black_Stark said:
Answer the following.
What rom?
What gapps?
What twrp version?
What phone? Kenzo or kate?
Click to expand...
Click to collapse
Stock ROM (MIUI 10), unrooted & everything stock. Kenzo.
BlasFamous said:
Stock ROM (MIUI 10), unrooted & everything stock. Kenzo.
Click to expand...
Click to collapse
Then factory reset and check issue.
Hello
One hour ago all the vibrations on my honor 8x just stopped working randomly, no changes after a reboot...
I'm on pie last update.
Any ideas how to fix that?
Been using the unit for 2 weeks or so. All of a sudden, there's no ecreen output at all.
It vibrates, it syncs to the amazfit app, it charges and the HR monitor does work.
Any idea on what happened? Should I RMA or is there any method to reset it and try my luck?
Ok, nevermind: Went to unpair it in order to RMA and it rebooted after clearing the data, and the screen came back to life.
If you ask me, this does not seem like a hardware issue... :S
How you have cleared the data withour screen not working?
rajithaw said:
How you have cleared the data withour screen not working?
Click to expand...
Click to collapse
Unpairing the watch from the amazfit app.
I had this happen another two times.
Last time it happened I refused to restore the settings when pairing it again and did not have this issue anymore (so far).
Happens to me as well.
Everyone it happens, I attempt to upload a new watchface via the Amazfit app, which causes the software to reboot. After the reboot everything works.
Looks like software issue to me.
Sent from my LYA-L29 using Tapatalk
blanck screen issue
i followed your instructions but it does not work my gts smartwatch screen does not work please help with another solution
Hello,
My Amazfit Bip is bricked on that "Connect APP to update" screen.
With MiFit, my smartwatch is never recognized.
With GadgetBridge, I connect to the smartwatch without any problem.
The smartwatch seems to "work" : I can ask GadgetBridge to have it vibrate, I can get activity etc.
With "Notify & Fitness for Amazfit", I have successfully flashed firmware 1.1.5.16 + GPS + RES (the screen changes to the firmware update screen). However, at the end, it does not reboot and remains stuck on the same Connect APP to update screen. The menu "reboot" or "factory reset" of GadgetBridge does not do anything.
Can someone please help unbrick it?
I would gladly try a more recent English firmware, but I haven't been able to find one. Links on 4pda.ru were down. I downloaded and unzipped a few Mi Fit apk, but they don't seem to have the Mili_chaohu files... etc
Thanks
Give this a try - use N & F to load a custom watchface (it doesn't matter which one).
This fixed my BIP in a similar situation.
Regards,
Eric
Solved after the battery drained
ebsebs said:
Give this a try - use N & F to load a custom watchface (it doesn't matter which one).
This fixed my BIP in a similar situation.
Regards,
Eric
Click to expand...
Click to collapse
Thanks, Eric, I had tried that, but it didn't work. It stayed on the same screen.
However, I solved the issue this morning, because at last the watch ran out of battery (lol ! the battery life is so good I nearly waited 2 months!). So, it was "dead", and then I charged it again, paired it with N & F, and suddenly MiFit took grasp of it, uploaded A-GPS, firmware and resources and after a while the smartwatch is back to life
axlc said:
Solved after the battery drained
Thanks, Eric, I had tried that, but it didn't work. It stayed on the same screen.
However, I solved the issue this morning, because at last the watch ran out of battery (lol ! the battery life is so good I nearly waited 2 months!). So, it was "dead", and then I charged it again, paired it with N & F, and suddenly MiFit took grasp of it, uploaded A-GPS, firmware and resources and after a while the smartwatch is back to life
Click to expand...
Click to collapse
Can you tell me how you fix it? I am in the same situation and I need more information about how you fix it.