Hi
went to up load the Poison Rom on the link below for my new T95z plus and once i loaded the rom i have no wifi or bluetooth when i boot up the device and it shows 0211 with the last 1 flashing or 0215 with the 5 flashing.
I have plugged in the male to male usb cable and tried reloading the firmware and it stops at 4% with error [0x10303004]romcode/switch status/identify/error result using USB burning tool 2.1.6 on the linked page below
https://forum.xda-developers.com/an...mputers/amlogic/t95z-plus-poison-rom-t3751720
Any help is much appreciated
Hazy261
hazy261 said:
Hi
went to up load the Poison Rom on the link below for my new T95z plus and once i loaded the rom i have no wifi or bluetooth when i boot up the device and it shows 0211 with the last 1 flashing or 0215 with the 5 flashing.
I have plugged in the male to male usb cable and tried reloading the firmware and it stops at 4% with error [0x10303004]romcode/switch status/identify/error result using USB burning tool 2.1.6 on the linked page below
https://forum.xda-developers.com/an...mputers/amlogic/t95z-plus-poison-rom-t3751720
Any help is much appreciated
Hazy261
Click to expand...
Click to collapse
I'm not a specialist but i had those errors.
1- There's a sd card in it, or
2- You got a LP Ram model, or
3- Usb burning tool/driver problem, badly installed maybe or connection to hub problem.
Related
Hello all. The problem concerns Sunvell T95Z 3/32 wifi AP6255. I bought this device from Android 7.1.2. It worked well but I wanted more. I updated to POISON from this thread https://forum.xda-developers.com/an...mputers/amlogic/t95z-plus-poison-rom-t3751720 It worked better but I wanted to try other ROM using USB Burn Tool but each of them stops at 2% with error [0x10105002] Romcode / Initialize DDR / Read Initialize Status / USB Control setup error . despite this error, I still used POISON installed. I created the SD card using Burn_Card_Maker and it killed my device. it is recognized in the Device Manager and connects to the USB Burn Tool but stops at 2% with an error. Charging from the card does not work. I tried probably all existing ROMs and different versions of the USB Burn Tool program, but to no avail.
I noticed a lot of people with this problem. HEEEEEEEEEEELP!!!!
Problem solved. Thanks to @ khn993 from this forum http://freaktab.com/forum/main-category/main-forum/637675-nand-chip-mask-rom-mode-short-location
firmware request
KrisObcy said:
Hello all. The problem concerns Sunvell T95Z 3/32 wifi AP6255. I bought this device from Android 7.1.2. It worked well but I wanted more. I updated to POISON from this thread https://forum.xda-developers.com/an...mputers/amlogic/t95z-plus-poison-rom-t3751720 It worked better but I wanted to try other ROM using USB Burn Tool but each of them stops at 2% with error [0x10105002] Romcode / Initialize DDR / Read Initialize Status / USB Control setup error . despite this error, I still used POISON installed. I created the SD card using Burn_Card_Maker and it killed my device. it is recognized in the Device Manager and connects to the USB Burn Tool but stops at 2% with an error. Charging from the card does not work. I tried probably all existing ROMs and different versions of the USB Burn Tool program, but to no avail.
I noticed a lot of people with this problem. HEEEEEEEEEEELP!!!!
Click to expand...
Click to collapse
dear KrisObcy,
have you got any solution?
the firmware link is not working. have u got a firmware for 2/16gb t95z plus? i will be very greateful to you if you share firmware with me please
regards
hello guys, recently I was to change the rom of my moto c plus by STAR OS before I had backed up the stock rom but in the twrp I just checked the system option and nvram, the problem is the following, it turns on, a message appears in the corner I can not install the SP flash tool because the smartphone is connecting and disconnecting alone, I've tried other usb ports, other cables and even different computers. , how to solve this?
Try this
leandro2200 said:
hello guys, recently I was to change the rom of my moto c plus by STAR OS before I had backed up the stock rom but in the twrp I just checked the system option and nvram, the problem is the following, it turns on, a message appears in the corner I can not install the SP flash tool because the smartphone is connecting and disconnecting alone, I've tried other usb ports, other cables and even different computers. , how to solve this?
Click to expand...
Click to collapse
Hi there,
try to reinstall the mediatek usb driver manually.
use google to find out how to
Thank you
KIBS2173
I have a H96 Pro Plus 3G32G ZH01-S912TVBOX-V3.0 with a green board and 7.1 firmware.
I suddenly stopped turning on, so after some research I found a solution of replacing the capacitor to 1000mf at the DC jack. Now it turns on but, wont boot. TWRP recovery was loading to splash screen but blacked out after that. I tried using the USB burning tool to flash the firmware, but it gets stuck on 7%. The SD card method also stopped at the same place and the device just powers off.
After trying a number of times with a few different firmwares, the SD card no longer boots at all and the USB burning tool still stops at 7% formatting.
I have a full TWRP backup of my stock firmware, but no way to restore it. This is the TWRP filename in case this helps.
2019-05-19--07-24-49_q201_9377-userdebug_7.1.2_NHG47L_20171020_t
Is there any way to make something flash to the device? Even if I can just get the recovery or bootloader working so that I can flash the backup.
Thanks for your help.
Here are some photos of the board.
From the log file, it's look like unstable usb connection, have you tried other usb male to male cable? the shorter the better
keatoncray said:
From the log file, it's look like unstable usb connection, have you tried other usb male to male cable? the shorter the better
Click to expand...
Click to collapse
It's one I've used on numerous occasions with other World Cup devices in the past. It has always worked with other devices, it seems more like a problem with the device.
beachbouy said:
I have a H96 Pro Plus 3G32G ZH01-S912TVBOX-V3.0 with a green board and 7.1 firmware.
I suddenly stopped turning on, so after some research I found a solution of replacing the capacitor to 1000mf at the DC jack. Now it turns on but, wont boot. TWRP recovery was loading to splash screen but blacked out after that. I tried using the USB burning tool to flash the firmware, but it gets stuck on 7%. The SD card method also stopped at the same place and the device just powers off.
After trying a number of times with a few different firmwares, the SD card no longer boots at all and the USB burning tool still stops at 7% formatting.
I have a full TWRP backup of my stock firmware, but no way to restore it. This is the TWRP filename in case this helps.
2019-05-19--07-24-49_q201_9377-userdebug_7.1.2_NHG47L_20171020_t
Is there any way to make something flash to the device? Even if I can just get the recovery or bootloader working so that I can flash the backup.
Thanks for your help.
Click to expand...
Click to collapse
From where you found solution to change its capacitor. Was it necessary. Being an Engineer, i dont think that it could be a capacitor rather faulty usb ports or power adaptor
awaisiqbal said:
From where you found solution to change its capacitor. Was it necessary. Being an Engineer, i dont think that it could be a capacitor rather faulty usb ports or power adaptor
Click to expand...
Click to collapse
It was on freaktab. The original problem was the box not turning on and the new capacitor worked for that. But unfortunately I found that solution after I had already tried to install the firmware unsuccessfully so the box is bricked. It would probably be fine if I had not tried to flash the firmware.
Hi guys
I've just received Tanix TX9S android box and I'm trying to flash a custom rom but my computer doesn't detect the box. I'm using Win 10 Pro 64bit and I've tried reinstalling the burning tool, installing with driver signature off, restarting, changing usb ports on both the pc and the box but it just doesn't work. I'm using this cable: https://www.aliexpress.com/item/4000574237363.html
Any ideas?
kalehrl said:
Hi guys
I've just received Tanix TX9S android box and I'm trying to flash a custom rom but my computer doesn't detect the box. I'm using Win 10 Pro 64bit and I've tried reinstalling the burning tool, installing with driver signature off, restarting, changing usb ports on both the pc and the box but it just doesn't work. I'm using this cable: https://www.aliexpress.com/item/4000574237363.html
Any ideas?
Click to expand...
Click to collapse
Cable Looks Quite Thin, It Says IUts A Data Cable So Should Work Just Might Not Provide Enough Power, Try Connecting Power At Same Time, that may help, or you might have to use mask rom mode to force your box to be detected
I tried connecting power but to no avail. I don't think I will be opening the box so I'll have to live with stock ROM
kalehrl said:
I tried connecting power but to no avail. I don't think I will be opening the box so I'll have to live with stock ROM
Click to expand...
Click to collapse
Aww, something you should try, when you eventually upgrade and it becomes a spare device
Maybe I can try with an sd card.
I also have some logs in amlogic folder.
I've noticed 'NoDeviceConnected' error and sometimes 'Other device'.
kalehrl said:
Maybe I can try with an sd card.
I also have some logs in amlogic folder.
I've noticed 'NoDeviceConnected' error and sometimes 'Other device'.
Click to expand...
Click to collapse
Yhea SD Card Is Another Option, i Just Generally don't recommend This Method as if you flash a incompatible firmware and your device wont turn on then USB Burn Tool Will Be needed To Fix And Flash From a "Bricked" State
I managed to flash my box.
I used the latest burning tool v3.1.0. During the installation, I plugged my box into the computer and saw that it not only installed world cup drivers, but additional ones as well which was a good sign. I also had to use the power supply because usb didn't output enough power.
kalehrl said:
I managed to flash my box.
I used the latest burning tool v3.1.0. During the installation, I plugged my box into the computer and saw that it not only installed world cup drivers, but additional ones as well which was a good sign. I also had to use the power supply because usb didn't output enough power.
Click to expand...
Click to collapse
I have the same issues. At the moment that you plugged in your box with usb cable was your box already on power? en did you have to use the reset by toothpick reset at the time you plugged in?
BUZZTV XRS4900
Yes, already on power and I used a toothpick.
But flashing is hit and miss with amlogic burning tool.
Sometimes it works, sometimes doesn't.
Try a different computer because for one of my boxes I had to use a Windows 7 machine.
kalehrl said:
Yes, already on power and I used a toothpick.
But flashing is hit and miss with amlogic burning tool.
Sometimes it works, sometimes doesn't.
Try a different computer because for one of my boxes I had to use a Windows 7 machine.
Click to expand...
Click to collapse
Thank you.. I tried several options and cables and pc's.
When on power the toothpick doesn't work because it is already operational i guess
I try the mask rom method. Hope that will do the job
kalehrl said:
I managed to flash my box.
I used the latest burning tool v3.1.0. During the installation, I plugged my box into the computer and saw that it not only installed world cup drivers, but additional ones as well which was a good sign. I also had to use the power supply because usb didn't output enough power.
Click to expand...
Click to collapse
this doesn't sound like a good sign to me... world cup drivers !!??
I've yet to flash my box and I'm really put off by the fact that guides mention to ignore virus warnings and just to click OK. I haven't yet seen it uploaded onto xda either which makes me confident.
Try older versions of the Amlogic USB Burning Tool, newer versions might not work with older boxes.
You can find most of the versions here: Amlogic USB Burning Tool - All Versions
The problem was the cable. The Chinese one I bought first didn't work properly. The cheapest one from Amazon worked fine.
Same here mine to does not detect but i have noticed in device manager it appears an unknown device
Reinstall the driver.
EdT586 said:
Try older versions of the Amlogic USB Burning Tool, newer versions might not work with older boxes.
You can find most of the versions here: Amlogic USB Burning Tool - All Versions
Click to expand...
Click to collapse
thxy men, i tried use the latest version and don't work, after saw ur comment i can revive my tv boxes
For kicks I tried a GSI ROM on my Jelly 2. It worked well except GSI ROMs don't seem to work well with VZW. So I'm looking to revert to the stock ROM. I have gone through the guide they posted here https://drive.google.com/file/d/1qVlaYucvE44ZJqF1RCHGknEBQWy_Z65m/view and I have the drivers installed and the phone is recognized as "MediaTek PreLoader USB VCOM (Android) (COMx)". Using their flash tool linked from the doc, the tool recognizes the phone on COMx (x depends on which USB port the cable is plugged into) and when I click "Start All" in the tool, in about 3-5 seconds the progress bar fills red to 100% and says "DA" in front of it. Then at about 125s, "DA" changes to "DA ERROR" and that's the end of the process.
Here are some screenshots showing the port in device manager and the flash tool with the "DA ERROR".
I've tried this from different laptops and different cables (the one that came with the phone and a different USB-A to USB-C cable) with no joy. I'm working with their support, but the time difference means communication is slow.
I've tried this with the bootloader locked and unlocked.
The IMEI for the Jelly 2 was recognized as a Jelly Pro, so Unihertz support provided me with an OTA file and instructions for installing it by downloading it to the phone and the using their built in local flash option to install it. They also provided 2 new IMEI numbers that I manually entered after flashing the OTA. This all worked fine, but they note that the IMEIs will revert to their original values after a factory reset. This was done before I flashed the GSI ROM, so I'm mentioning it in case it gives insight into whatever "DA ERROR" means.
Has anyone gone through this process successfully and have any tips?
bra1niac said:
For kicks I tried a GSI ROM on my Jelly 2. It worked well except GSI ROMs don't seem to work well with VZW. So I'm looking to revert to the stock ROM. I have gone through the guide they posted here https://drive.google.com/file/d/1qVlaYucvE44ZJqF1RCHGknEBQWy_Z65m/view and I have the drivers installed and the phone is recognized as "MediaTek PreLoader USB VCOM (Android) (COMx)". Using their flash tool linked from the doc, the tool recognizes the phone on COMx (x depends on which USB port the cable is plugged into) and when I click "Start All" in the tool, in about 3-5 seconds the progress bar fills red to 100% and says "DA" in front of it. Then at about 125s, "DA" changes to "DA ERROR" and that's the end of the process.
Here are some screenshots showing the port in device manager and the flash tool with the "DA ERROR".
I've tried this from different laptops and different cables (the one that came with the phone and a different USB-A to USB-C cable) with no joy. I'm working with their support, but the time difference means communication is slow.
I've tried this with the bootloader locked and unlocked.
The IMEI for the Jelly 2 was recognized as a Jelly Pro, so Unihertz support provided me with an OTA file and instructions for installing it by downloading it to the phone and the using their built in local flash option to install it. They also provided 2 new IMEI numbers that I manually entered after flashing the OTA. This all worked fine, but they note that the IMEIs will revert to their original values after a factory reset. This was done before I flashed the GSI ROM, so I'm mentioning it in case it gives insight into whatever "DA ERROR" means.
Has anyone gone through this process successfully and have any tips?
Click to expand...
Click to collapse
Answering my own question, while I could never resolve the DA ERROR running the SP TOOL on a Windows laptop, it worked running the Linux version from a bootable thumb drive on the same laptop. No idea on this one but I'm not going to dig any deeper. I used fireiso-2.0.0 as the bootable Linux thumb drive and downloaded the Linux SP Tool after the system booted up. Ran it with no changes to anything and it just worked.