Try rooting my Samsung j7 Prime SM-G610M device with CF-Auto-Root. The case is that under the CF-Auto-Root corresponding to version 8.1.0 Oreo of my Mobile with the same number of compilation, but when flashing from Odin, it tells me everything is correct, but it restarts, I verify with Root Checker that I have rooted, but he says no. Below I leave the log generated by Odin to review.
Code:
<ID: 0/005> Added !!
<OSM> Enter CS for MD5 ..
<OSM> Check MD5 .. Do not unplug the cable ..
<OSM> Please wait ..
<OSM> Checking MD5 finished Successfully ..
<OSM> Leave CS ..
<ID: 0/005> Odin engine v (ID: 3.1203) ..
<ID: 0/005> File analysis ..
<ID: 0/005> SetupConnection ..
<ID: 0/005> Initialzation ..
<ID: 0/005> Get PIT for mapping ..
<ID: 0/005> Firmware update start ..
<ID: 0/005> SingleDownload.
<ID: 0/005> recovery.img
<ID: 0/005> cache.img
<ID: 0/005> RQT_CLOSE !!
<ID: 0/005> RES OK!
<ID: 0/005> Removed !!
<ID: 0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID: 0/004> Added !!
<ID: 0/004> Removed !!
<ID: 0/004> Added !!
<ID: 0/004> Removed !!
[/ code]
Forgive my English, I'm from Argentina and use the Google translator ...
Related
Hi, i was try to update my N7000 to 4.1.2 , when i was use Odin to PC, it stuck on as below , i was left it in more than 30mins.
<OSM> Please wait..
<OSM> N7000DXLSE_N7000OLBLSE_N7000DXLS8_HOME.TAR.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> zImage
<ID:0/016> NAND Write Start!!
and i also turn off my phone & start again to recovery mode , it can not turn it , it just stuck on start page ( GT- N7000 ).
what can i do ps help.
TQ
Wrong forum, this is I9100 Q&A. I've asked mods to move your thread here, wait until they do/someone replies.
Hi all, I will explain briefly what happens to my S3 (GT-I9300) is "soft brick" enters the "downloads" only. If I want to enter the recovery mode, restarts and freezes once the logo of Samsung.
I tried to make a flash via Odin (1.85, 3.07 version) by following the appropriate steps. A negative result (fails). I read that it could be the file "PITS" I have also tried different and never-ending operation is always the result is "fail". After that I have to turn off the phone by removing the battery, it is the only way to recognize ODIN again.
The end result is always the same:
<ID: 0/005> Added !!
<OSM> Enter CS for MD5 ..
<OSM> Check MD5 .. Do not unplug the cord ..
<OSM> Please wait ..
<OSM> I9300UBUGML1_I9300ANCUGMK1_I9300UBUGMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 Sucessfully finished ..
<OSM> Leave CS ..
<ID: 0/005> Odin v.3 engine (ID: 5) ..
<ID: 0/005> File analysis ..
<ID: 0/005> SetupConnection ..
<ID: 0/005> initialzation ..
<ID: 0/005> Get PIT for mapping ..
<ID: 0/005> Firmware update start ..
<ID: 0/005> sboot.bin
<ID: 0/005> Write Start NAND !!
<ID: 0/005> Transmission Complete ..
<ID: 0/005> Now Writing .. Please wait about 2 minutes
<ID: 0/005> Receive Response from boot-loader
<ID: 0/005> FAIL!
<OSM> All threads completed. (Succeed 0 / failed 1)
Try flashing bootloader BLFB then try firmware flash with pit. If still the same then your emmc chip is broken.
boomboomer said:
Try flashing bootloader BLFB then try firmware flash with pit. If still the same then your emmc chip is broken.
Click to expand...
Click to collapse
thank you very much I will try and tell you
agus_311 said:
thank you very much I will try and tell you
Click to expand...
Click to collapse
Hi. There was no case, apparently the cell is damaged. Any other suggestions? or is it like a cute paperweights... =(
Thanks
Hello. I have a problem. I have a samsung galaxy s6 unit g925x demo edge. I wanted to write it soft 1 g925f a file from which the normal S6 edge. When I included the phone in bootloader mode and tried to write it with a soft by Odin to the odinie jump out the mistake .... Here below you log oo Odin:
<ID: 0/004> Added !!
<OSM> Enter CS for MD5 ..
<OSM> Binary Check MD5 .. Do not disconnect the cable ..
<OSM> Please wait ..
<OSM> Checking successfully completed MD5 ..
<OSM> Leave CS ..
<ID: 0/004> Odin engine v (ID: 3.1100) ..
<ID: 0/004> Analysis file ..
<ID: 0/004> SetupConnection ..
<ID: 0/004> Initialzation ..
<ID: 0/004> Download PIT for mapping ..
<ID: 0/004> Firmware start the update ..
<ID: 0/004> SingleDownload.
<ID: 0/004> boot.img
<ID: 0/004> NAND Record start !!
<ID: 0/004> cache.img
<ID: 0/004> cm.bin
<ID: 0/004> FAIL!
<ID: 0/004>
<ID: 0/004> Complete (Write) operation failed.
<OSM> All threads completed. (Good luck 0 / failed: 1)
Now when I try to turn the phone to either stands on logu galaxy s6 demo unit edge OR appears: An error occurred while updating the device software.Use function of the emergency recovery intelligent software switch. When you want to write it by an intelligent software switch to show that the ten model or g925x demo NO Support scales This program ...
I do not know what to do Help please. I count on it
Personal speech.
Would help to solve the problem I'm going through.
Was using the ROM "cm-13.0-20160901-UNOFFICIAL-Temasek-i9305" and did the usual procedure (already done several times this process), however an hour to another cell restarted and was caught in the BOOT screen ..
I entered the TWRP mode and received a "No OS installed" message.
Based on that, I tried to install the ROM again, but the TWRP can not read the micro sd and not the internal memory.
From that, I tried to return to original ROM, however I am getting this fault message on ODIN:
<OSM> Enter CS is MD5 ..
<OSM> Binary Check MD5 .. Do not unplug the cable ..
<OSM> Please wait ..
<OSM> Checking MD5 finished sucessfully ..
<OSM> Leave CS ..
<ID: 0/005> Added !!
<ID: 0/005> Odin engine v (ID: 3.1100) ..
<ID: 0/005> File analysis ..
<ID: 0/005> SetupConnection ..
<ID: 0/005> Initialzation ..
<ID: 0/005> Get PIT for mapping ..
<ID: 0/005> Firmware update start ..
<ID: 0/005> SingleDownload.
<ID: 0/005> tz.img
<ID: 0/005> NAND Write Start !!
<ID: 0/005> FAIL!
<ID: 0/005>
<ID: 0/005> Complete (Write) operation failed.
<OSM> All completed threads. (0 succeed / failed 1)
I've used the version of ODIN (3:07, 3:10, 3:12) all display the same error.
I also noticed that when you enter the TWRP and access any folder, I get the message in the log:
unable to mount the store
Failed to mount (invalid argument)
i am trying to flash stock firmware to my s6 edge with odin
with G925FXXU3COI9_G925FOLB3COJ1_G925FXXU3COJ4_HOME firmware XSE /indo
tried to flash and error occurs
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/021> Added!!
<ID:0/021> Odin engine v(ID:3.1203)..
<ID:0/021> File analysis..
<ID:0/021> SetupConnection..
<ID:0/021> Initialzation..
<ID:0/021> Get PIT for mapping..
<ID:0/021> Firmware update start..
<ID:0/021> SingleDownload.
<ID:0/021> sboot.bin
<ID:0/021> FAIL!
<ID:0/021>
<ID:0/021> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
in download mode error shows "SW REV. CHECK FAIL. DEVICE: 4, BINARY:3"
and i also screwed up my recovery menu so its stuck on samsung s6 edge logo with text "recovery is not seandroid enforcing"
please help me solve this problem