[MTK] How to Enable "VoLTE" in MediaTek Devices. - Android Q&A, Help & Troubleshooting

Today I'm give a solution to enable (VoLTE) in Mediatek Devices.
To Begin. - First download and install "MTK Engineering mode" app or if you not have the app then install "MTK Engineering mode Plus" app from Play Store.
2. - After install open the app, Goto "Telephony" Section.
3. - In "Telephony" section, select "ViLTE" option.
4. - In "ViLTE" option Click/Select "Disable" in "Media Loopback Mode"
5. - Just Check below, the line named "persist.radio.vilte_ut_support" should be "0". If you Click/Select the "Enable" it will be "1". So be it
"0".
6. - Restart the Phone.
And after restarting phone the "VoLTE" Logo will be seen means it is enabled. After you can make calls and send messages.
If any problem persists, Please reply or comment below. Or send me Screenshots of the problem.

Not working

Nived2601 said:
Not working
Click to expand...
Click to collapse
Send me your device model and screenshots of the problem..

Not working. Mine don't have :-
'4.- In "ViLTE" option Click/Select "Disable" in "Media Loopback Mode"
5. - Just Check below, the line named "persist.radio.vilte_ut_support" should be "0". If you Click/Select the "Enable" it will be "1". So be it '0".'
I attached screenshots for your eyes. Pls need some advices.

art_1405 said:
Not working. Mine don't have :-
'4.- In "ViLTE" option Click/Select "Disable" in "Media Loopback Mode"
5. - Just Check below, the line named "persist.radio.vilte_ut_support" should be "0". If you Click/Select the "Enable" it will be "1". So be it '0".'
I attached screenshots for your eyes. Pls need some advices.
Click to expand...
Click to collapse
Which device model and chipset is of your smartphone?
About point "5", find the line given in terminal emulator by root permission by typing "df" in terminal....

Ashutosh1358 said:
Today I'm give a solution to enable (VoLTE) in Mediatek Devices.
To Begin. - First download and install "MTK Engineering mode" app or if you not have the app then install "MTK Engineering mode Plus" app from Play Store.
2. - After install open the app, Goto "Telephony" Section.
3. - In "Telephony" section, select "ViLTE" option.
4. - In "ViLTE" option Click/Select "Disable" in "Media Loopback Mode"
5. - Just Check below, the line named "persist.radio.vilte_ut_support" should be "0". If you Click/Select the "Enable" it will be "1". So be it
"0".
6. - Restart the Phone.
And after restarting phone the "VoLTE" Logo will be seen means it is enabled. After you can make calls and send messages.
If any problem persists, Please reply or comment below. Or send me Screenshots of the problem.
Click to expand...
Click to collapse
I am trying to run volte for a device with an mt6761 processor do you know how I run ??

Darkmanisr said:
I am trying to run volte for a device with an mt6761 processor do you know how I run ??
Click to expand...
Click to collapse
Does it Supports Volte or just 4G. Cause it has difference in it. Can you tell me your mobile model and specifications of your phone too???

Ashutosh1358 said:
Does it Supports Volte or just 4G. Cause it has difference in it. Can you tell me your mobile model and specifications of your phone too???
Click to expand...
Click to collapse
Yes it’s support 4g
Device: qin f21pro
Processor:mtk 6761
Thanks

Darkmanisr said:
Yes it’s support 4g
Device: qin f21pro
Processor:mtk 6761
Thanks
Click to expand...
Click to collapse
Have you tried jio sim or any sim that supports Volte??

Ashutosh1358 said:
Have you tried jio sim or any sim that supports Volte??
Click to expand...
Click to collapse
There is no 2 sim cards in this phone, just 1

Darkmanisr said:
There is no 2 sim cards in this phone, just 1
Click to expand...
Click to collapse
See, mostly this is a feature phone, so some regions especially in China, in their sims which supports VOlte. And in india for this phone should support band 22 and 31 but by default the OEM has locked those bands in the phone itself.
Just check the bootloader is unlocked, go to Build number in settings - about Phone - Build number, click seven times to it and check Developer options in settings and just check there is tick on OEM unlock option. If it's ticked then the bootloader is unlocked. (Just reply me about this first....)
If your phone is warranty then don't try to Root your phone, if rooted then it can void your warranty.

Ashutosh1358 said:
See, mostly this is a feature phone, so some regions especially in China, in their sims which supports VOlte. And in india for this phone should support band 22 and 31 but by default the OEM has locked those bands in the phone itself.
Just check the bootloader is unlocked, go to Build number in settings - about Phone - Build number, click seven times to it and check Developer options in settings and just check there is tick on OEM unlock option. If it's ticked then the bootloader is unlocked. (Just reply me about this first....)
If your phone is warranty then don't try to Root your phone, if rooted then it can void your warranty.
Click to expand...
Click to collapse
The device's bootloader is open, and I rooted it

Darkmanisr said:
The device's bootloader is open, and I rooted it
Click to expand...
Click to collapse
To have you tried solution given above??

Ashutosh1358 said:
Have you tried jio sim or any sim that supports Volte??
Click to expand...
Click to collapse
Yes of course I tried, I realized the problem is that the company did not add the lines of code of the cellular modem for volte

Darkmanisr said:
Yes of course I tried, I realized the problem is that the company did not add the lines of code of the cellular modem for voltejust
Click to expand...
Click to collapse

Darkmanisr said:
Yes of course I tried, I realized the problem is that the company did not add the lines of code of the cellular modem for volte
Click to expand...
Click to collapse
Can you send me your screenshot of Engineer mode plus apk mentioned above in solution??

Ashutosh1358 said:
Can you send me your screenshot of Engineer mode plus apk mentioned above in solution??
Click to expand...
Click to collapse
This is given me an error

Darkmanisr said:
This is given me an error
Click to expand...
Click to collapse
Download latest Engineer mode apk
Copy apk and paste in /system/app
Restart the device.
Check in Settings -> applications -> Engineer mode apk is installed or not.
After that, Go to MTK settings after that follow given procedure...

Hello,
I don't have the option either.
I installed the APK you recommended above, this is an MTK 6731 device. Any idea on how to make it appear?
Device is rooted & bootloader is unlockable.

bassam_chedar said:
Hello,
I don't have the option either.
I installed the APK you recommended above, this is an MTK 6731 device. Any idea on how to make it appear?
Device is rooted & bootloader is unlockable.
View attachment 5579627
Click to expand...
Click to collapse
Can u send me your model details please???

Related

Getting SPC Unlocking SIM M9 SPRINT [NV]

Download NV-items_reader_writer.rar
You must have HTC Drivers in your PC .
Instructions
1 - Getting MSL / SPC
Dial ##3424# then choose DM ON .
If it asks you for MSL/SPC .
Try This
or you can go with the old method
You must be rooted
Write this in cmd
Code:
adb shell
su
echo 1 > /sys/devices/virtual/android_usb/android0/f_diag/func_en
You must hear you phone been reconnected .
a - Download Basic-Flasher.7z
b - Open Basic-Flasher click scan then select your phone port number and then connect.
c - Select HTC instead of nv, then click read, the MSL/SPC should appear down .
2 - Unlock
a - Open NV reader/writer tools
b - Click "port" in the top left and select your phone serial port.
c - Make sure BOTH boxes in the top bar are checked, and write you SPC/MSL in the box where is 000000
d - Click connect in the top par.
e - Click read in the top par which is next to connect not the other one, you should see a log message bellow says the > SPC is correct. Phone unlocked .
f - Make a backup for your current nv item
Where is Range (Dec): you will see two boxes, write in both of them this number, which is the number of the item that
will be changed, 30159 , now click Read and save it .
g - Click Write and choose the attached unlock file .
h - Go to Mode and then reboot .
If didn't work try factory reset. If didn't work also try flashing RUU again .
thats it I hope it helps
Enjoy
HTC DM Caller
Root is required
Enable Diag then read SPC via BasicFlasher.exe
Try Method 1, if didn't work try Method 2.
Excellent!!!
How can i find my port number?
Haha,so exciting,it works with my phone (I am on BAD BOY ROMZ 6.0),3q your good work.
Larethio said:
How can i find my port number?
Click to expand...
Click to collapse
Right click on computer icon > manage > device manager > ports
There will be a list of the devices that are connected to your PC , you shall see it there :good:
Worked fine
Thank you a lot.
Where I must write it?
"echo 1 > /sys/devices/virtual/android_usb/android0/f_diag/on"
morgulis said:
Where I must write it?
"echo 1 > /sys/devices/virtual/android_usb/android0/f_diag/on"
Click to expand...
Click to collapse
Open CMD
Write
Code:
adb shell
su
You should see your phone name followed by # NOT $
Then that command
Hello,
So after following the instructions, the phone will work with any carrier?
dohcvtec said:
Hello,
So after following the instructions, the phone will work with any carrier?
Click to expand...
Click to collapse
At least 2G and 3G, it doesn't have all the 4G bands. (I suppose due to CDMA)
romka.t said:
At least 2G and 3G, it doesn't have all the 4G bands. (I suppose due to CDMA)
Click to expand...
Click to collapse
Okay. Thank you.
My question was provoked by this information:
Sprint, Verizon, Boost Mobile, and U.S. Cellular use CDMA.
AT&T, T-Mobile, Metro PCS, and Cellular One use GSM.
I unlocked gsm network. Calls work but data transfer - NO. What could be the problem?
morgulis said:
I unlocked gsm network. Calls work but data transfer - NO. What could be the problem?
Click to expand...
Click to collapse
Give us some details. Where are you located?
romka.t said:
Give us some details. Where are you located?
Click to expand...
Click to collapse
Kiev, Ukraine.
morgulis said:
Kiev, Ukraine.
Click to expand...
Click to collapse
I'm quite sure you won't have 4G LTE data in any case. Try to set your phone's network mode to 2g/3g only. Also you might want to check your APN settings, it's quite possible that you need to enter your settings manually.
Working perpect for me
This was save my life.
Thank your very much :good:
batsuuri said:
This was save my life.
Thank your very much :good:
Click to expand...
Click to collapse
what android version did your phone have?
romka.t said:
what android version did your phone have?
Click to expand...
Click to collapse
I believe he is on Marshmallow...http://forum.xda-developers.com/showpost.php?p=65365234&postcount=2821
Will it unlock the phone for cdma sim usage? Want to use it in india

Sprint Galaxy Note 3 International & Domestic Sim Unlock Android 5.0

Well I got ahold of my 5th note 3 and nobody has the best step on how to unlock it on android 5.0 OC5 without downgrading back 4.2 so i will be posting it
Step 1:
Root it using it CF-Auto-root
https://download.chainfire.eu/362/CF-Root/CF-Auto-Root/CF-Auto-Root-hltespr-hltespr-smn900p.zip
Step 2:
Get ahold of iDone's GTv3.1.5.apk & GTUpdate2_v3.1.8.apk Install them and do the update but dont press unlock yet
Step 3 :
Downgrade the modem back M13 or Mj4 (i will double check but i have the link for the one i used )
https://mega.nz/#!mg5nVZiD
I think it was m13 plus my phone says it sooo lol
Step 4 :
After downgrading the modem back to m13 you can now go to idone gt app and press (SIM UICC Unlock) after that restart the phone (now the phone is internationally unlock)
Step 5 :
Final in the unlocking process for it work in the united states aka domestic
Goto the phone app and dial *#0011# the menu should open up press menu and back then menu key input "Q" press ok then press menu key input again "0000" press ok and wait for the menu to open
UE Setting & Info >Setting >Protocol >GCF >GSM/(E)GPRS/WCDMA GCF ON
It will say "success". Reboot the device then its domestically unlock
P.S. if you are you are using a International sim the us in order for it to roam you would have to do this step
Im also not responsible for any damage done to your device :good:
on step 3, the link prompts to insert decryption key
Unlocking Procedure
I'm new to unlocking and wanted to know if it's possible for you to add a bit more detail to this unlock procedure?
Thanks
Mitch
Note 3 unlock on domestic network
AndroidKing said:
Step 5 :
Final in the unlocking process for it work in the united states aka domestic
:good:
Click to expand...
Click to collapse
By domestic unlock do u mean it will work on t mobile?
Wow, this works perfectly. Running on AT&T.
Thanks : )
AndroidKing said:
Well I got ahold of my 5th note 3 and nobody has the best step on how to unlock it on android 5.0 OC5 without downgrading back 4.2 so i will be posting it
Step 1:
Root it using it CF-Auto-root
https://download.chainfire.eu/362/CF-Root/CF-Auto-Root/CF-Auto-Root-hltespr-hltespr-smn900p.zip
Step 2:
Get ahold of iDone's GTv3.1.5.apk & GTUpdate2_v3.1.8.apk Install them and do the update but dont press unlock yet
Step 3 :
Downgrade the modem back M13 or Mj4 (i will double check but i have the link for the one i used )
https://mega.nz/#!mg5nVZiD
I think it was m13 plus my phone says it sooo lol
Step 4 :
After downgrading the modem back to m13 you can now go to idone gt app and press (SIM UICC Unlock) after that restart the phone (now the phone is internationally unlock)
Step 5 :
Final in the unlocking process for it work in the united states aka domestic
Goto the phone app and dial *#0011# the menu should open up press menu and back then menu key input "Q" press ok then press menu key input again "0000" press ok and wait for the menu to open
UE Setting & Info >Setting >Protocol >GCF >GSM/(E)GPRS/WCDMA GCF ON
It will say "success". Reboot the device then its domestically unlock
P.S. if you are you are using a International sim the us in order for it to roam you would have to do this step
Im also not responsible for any damage done to your device :good:
Click to expand...
Click to collapse
What is the "Enter decryption key" that we need for Step 3?
IT WORKS!!!
I was getting 3G and H+ on my N900P and I couldn't have been more happy. Alright, so I've uploaded a zip file with everything you need.
Here's the link to the zip file on my Google Drive: http://bit.ly/1oZDO9t
Edit: The modem is version MI3 (That's emm eye three). Also, after you apply the GCF settings and reboot, you need to change your mobile networks settings from CDMA/LTE to GSM/UMTS for the new SIM card to be recognized. Enjoy!
BlockOfDynamite said:
IT WORKS!!!
I was getting 3G and H+ on my N900P and I couldn't have been more happy. Alright, so I've uploaded a zip file with everything you need.
Here's the link to the zip file on my Google Drive: link removed
Edit: The modem is version MI3 (That's emm eye three). Also, after you apply the GCF settings and reboot, you need to change your mobile networks settings from CDMA/LTE to GSM/UMTS for the new SIM card to be recognized. Enjoy!
Click to expand...
Click to collapse
I tried to download the zip file from the link provided and received a binary file.
JeopardyRage said:
I tried to download the zip file from the link provided and received a binary file.
Click to expand...
Click to collapse
What do you mean you received a binary file? What was the extension on the file you got? It should be a .zip file. If it's not, you'll have to redownload it.
BlockOfDynamite said:
What do you mean you received a binary file? What was the extension on the file you got? It should be a .zip file. If it's not, you'll have to redownload it.
Click to expand...
Click to collapse
Download in browser, got that trying to download with Google drive.
Sent from my SM-G920V using XDA-Developers mobile app
rbeavers said:
Download in browser, got that trying to download with Google drive.
Sent from my SM-G920V using XDA-Developers mobile app
Click to expand...
Click to collapse
It should look like this in your browser. Make sure you click the download button on the top. If it comes out as anything but .zip, then try a different browser.
toolsoldier said:
on step 3, the link prompts to insert decryption key
Click to expand...
Click to collapse
https://docs.google.com/uc?id=0B5gwgS8Wzjj1QzFuaXF0WFNnenc&export=download
It didn't work
I went through the process but when I click the sim UICC unlock a new notification pops up asking, network unlock asking for control key
MI3 Modem needed
Daniel Owusu said:
I went through the process but when I click the sim UICC unlock a new notification pops up asking, network unlock asking for control key
Click to expand...
Click to collapse
I had same problem at first, I didn't go back to modem MI3 from OK2, after it worked perfectly.
it didn't work
My sprint note 3 uicc now shows that the phone is unlocked but there is a red X on the network signal bar. How can I get rid of this to make my phone work? Please help
My network is blocked and IMEI certi shows failed
I have been able to unlock the phone but when I checked on the service mode, I realized the network is blocked and the IMEI certi shows failed.
This has caused the network signal bar to show a red X. Though unlocked, there is no signal showing. Any help please
AndroidKing said:
Well I got ahold of my 5th note 3 and nobody has the best step on how to unlock it on android 5.0 OC5 without downgrading back 4.2 so i will be posting it
Step 1:
Root it using it CF-Auto-root
https://download.chainfire.eu/362/CF-Root/CF-Auto-Root/CF-Auto-Root-hltespr-hltespr-smn900p.zip
Step 2:
Get ahold of iDone's GTv3.1.5.apk & GTUpdate2_v3.1.8.apk Install them and do the update but dont press unlock yet
Step 3 :
Downgrade the modem back M13 or Mj4 (i will double check but i have the link for the one i used )
https://mega.nz/#!mg5nVZiD
I think it was m13 plus my phone says it sooo lol
Step 4 :
After downgrading the modem back to m13 you can now go to idone gt app and press (SIM UICC Unlock) after that restart the phone (now the phone is internationally unlock)
Step 5 :
Final in the unlocking process for it work in the united states aka domestic
Goto the phone app and dial *#0011# the menu should open up press menu and back then menu key input "Q" press ok then press menu key input again "0000" press ok and wait for the menu to open
UE Setting & Info >Setting >Protocol >GCF >GSM/(E)GPRS/WCDMA GCF ON
It will say "success". Reboot the device then its domestically unlock
P.S. if you are you are using a International sim the us in order for it to roam you would have to do this step
Im also not responsible for any damage done to your device :good:
Click to expand...
Click to collapse
Better solution here. Just tryin to help http://forum.xda-developers.com/note-3-sprint/help/how-to-t-mobile-gsm-true-4g-lte-unlock-t3448000
johnb4200 said:
Better solution here. Just tryin to help http://forum.xda-developers.com/note-3-sprint/help/how-to-t-mobile-gsm-true-4g-lte-unlock-t3448000
Click to expand...
Click to collapse
No LTE, don't know about sim unlock.
Sent from my SM-G920V using XDA-Developers mobile app
rbeavers said:
No LTE, don't know about sim unlock.
Sent from my SM-G920V using XDA-Developers mobile app
Click to expand...
Click to collapse
Hey rbeavers what do you mean don't know about sim unlock did you urself try my method and now running a tmobile sim on a tmobile rom on your exsprint note I also pm you my personal phone number to assist u in getting your lte going should be a cinch since you got 4g up already
johnb4200 said:
Hey rbeavers what do you mean don't know about sim unlock did you urself try my method and now running a tmobile sim on a tmobile rom on your exsprint note I also pm you my personal phone number to assist u in getting your lte going should be a cinch since you got 4g up already
Click to expand...
Click to collapse
As I said, in your thread, I was unlocked all ready.
Sent from my SM-G920V using XDA-Developers mobile app

Unlock a sm-g925r7 Ntelos ,Please help me.

Hi guys , i dunno if this is the right section for this question but i'm a newbie here , i got two sm-g925r7 locked to nTelos i think and i want to unlock them for international gsm use outside the u.s , is this possible ? if yes do you know a guy who can do them at a reasonably price ? since this can work on sprint cdma phones i don't see why it can't work on nTelos since they are both cdma ? correct me if i'm wrong , i need your help guuuuuys please.
How do you know if they're locked to nTelos? Did you try putting in another carrier's Sim card? Uru
nothing happens
i know couse i bought them on ebay and the sellers stated that in their description , and the sm-g925r7 is for cspire or ntelos only ? i tried using a foreign sim card , ( i'm outside the u.s ) and nothing happens , phones search for network 2-3 secs and then they just show that little barred signal icon on the top right corner
Well on the nTelos website it says all android phones are unlocked so I dont know.
checked that
DJCharlie said:
Well on the nTelos website it says all android phones are unlocked so I dont know.
Click to expand...
Click to collapse
yeah man i already checked that , but if it's a remote unlock i think it can be done by using a sprint firmware
mariosota said:
i know couse i bought them on ebay and the sellers stated that in their description , and the sm-g925r7 is for cspire or ntelos only ? i tried using a foreign sim card , ( i'm outside the u.s ) and nothing happens , phones search for network 2-3 secs and then they just show that little barred signal icon on the top right corner
Click to expand...
Click to collapse
that model just sends sms and LTE data, no calls
DEXEIL said:
that model just sends sms and LTE data, no calls
Click to expand...
Click to collapse
How can i unlock these features at least? Or it should be ready when u put a 4g sim card , i tried using old 3g sim cards and it just searches for signal
mariosota said:
How can i unlock these features at least? Or it should be ready when u put a 4g sim card , i tried using old 3g sim cards and it just searches for signal
Click to expand...
Click to collapse
You can unlock by enabling service menu
-Insert 4G sim card
Dial *#27663368378# -This will put you in service mode
* tap UE Settings & Info > Settings > Protocol > NAS > Network Control > Band Selection > Choose choice 7 “LTE/GSM MODE ONLY”
Restart
DEXEIL said:
You can unlock by enabling service menu
-Insert 4G sim card
Dial *#27663368378# -This will put you in service mode
* tap UE Settings & Info > Settings > Protocol > NAS > Network Control > Band Selection > Choose choice 7 “LTE/GSM MODE ONLY”
Restart
Click to expand...
Click to collapse
Ok I'll try this code , i tried several ones but with no success , i think the firmware blocks all codes on these phones .Thanks mate
mariosota said:
Ok I'll try this code , i tried several ones but with no success , i think the firmware blocks all codes on these phones .Thanks mate
Click to expand...
Click to collapse
you can enable service menu by rooting the phone, tested on android 5.0.2 and 5.1.1
DEXEIL said:
you can enable service menu by rooting the phone, tested on android 5.0.2 and 5.1.1
Click to expand...
Click to collapse
Ok I'll root using the sprint rooting as I've tried this before with success, but first I'll downgrade them to 5.1.1 and hopefully i'll get past this ,since the settings will be set to lte/gsm why wouldn't it work with calls ?
mariosota said:
Ok I'll root using the sprint rooting as I've tried this before with success, but first I'll downgrade them to 5.1.1 and hopefully i'll get past this ,since the settings will be set to lte/gsm why wouldn't it work with calls ?
Click to expand...
Click to collapse
I hope flashing to sprint version or trying with different bootloader / modems could be the solution, I have not found any guide yet
Ok so i rooted the phone and used root explorer to enable service mode , restarted the phone , opened service mode and selected lte/gsm only , restart , phone asks for sim pin and then nothing , no data sms or calls
I am also interested in this unlock but haven't found a solution yet.
mariosota said:
Ok so i rooted the phone and used root explorer to enable service mode , restarted the phone , opened service mode and selected lte/gsm only , restart , phone asks for sim pin and then nothing , no data sms or calls
Click to expand...
Click to collapse
after enabling lte/gsm only, restart and go to settings > network mode > select lte/wcdma/gsm. try with different carriers and 4G sim cards to get signal (mine is working on Claro only, other carriers show "Searching" or "No service" )
If this is the go25r7wwu3cpc1 how did you root?? I'm on firmware 6.0.1 can't find root anywhere..
mariosota said:
Ok I'll root using the sprint rooting as I've tried this before with success, but first I'll downgrade them to 5.1.1 and hopefully i'll get past this ,since the settings will be set to lte/gsm why wouldn't it work with calls ?
Click to expand...
Click to collapse
you tryed to unlock with z3x box?
g925r7 is currently not listed in Z3X box support list.
need rmt_storage patch to make changes to bands inside the phone.
inside item 1787 (3G GSM bands), this item has no support.
Reason why it doesn't work for calls is because VOLTE is not enabled by default in CSC
usually a device like this will fall back to 3G when making calls on GSM networks. Thus the reason why calls aren't working.
sins07 said:
need rmt_storage patch to make changes to bands inside the phone.
inside item 1787 (3G GSM bands), this item has no support.
Reason why it doesn't work for calls is because VOLTE is not enabled by default in CSC
usually a device like this will fall back to 3G when making calls on GSM networks. Thus the reason why calls aren't working.
Click to expand...
Click to collapse
Sir. Is is possible to make any changes to make it work?

[GUIDE] Band unlocking for OP2

After reading through the OPO thread and someone confirming they saw bands unlocked for their OP2, but could not test if they are working as well as reading through the OP3 and similar threads with our processor I finally delved into trying this. Here is the quick guide of how to do it. Sorry if there is any confusion I will try my best to make it concise as possible. This is my first time writing a guide up for XDA.
I have not been able to test each band to confirm it's working, but it is showing up in Network Guru. I am on AT&T so I only unlocked AT&T bands (bc that's all I care about currently and it makes it easier for me to test)
I WILL NOT BE HELD RESPONSIBLE IF SOMETHING WRONG HAPPENS TO YOUR DEVICE BY FOLLOWING THIS GUIDE!
Credit: All my fellow XDA'rs who have been diligently testing, experimenting, bricking/unbricking, creating ROMs, FLASH, Root ability, and Bootloader unlocking. You are the heart and soul of XDA!
[URL="https://forum.xda-developers.com/member.php?u=4066277" @otonieru[/URL] for the concise guide
[URL="https://forum.xda-developers.com/member.php?u=7846474" @baskaflyfer[/URL] Rmt Storage Patch Zip
Here is the OP3 thread I based this guide off of and credit to all those mentioned in there as getting this far would have been impossible without them: https://forum.xda-developers.com/oneplus-3/how-to/guide-unlock-additional-lte-bands-t3519563
OKAY:
PreReq's:
1. Rooted
2. TWRP or like
3. RMT Storage patch from OP3 forums: SEE POST BELOW!
4. DFS Explorer - Find via searching XDA, again checking OP3 thread or OPO
5. ADB installed (whether that be minimal ADB or like from other toolboxes out there)
6. QPST - Check forums for download
Guide:
1. Put phone in MTP mode if not default (Some default to charge mode) Just go to status bar and press the charging mode to change to file transfer
2. Place file from PRE-REQ #3 in a folder you'll remember
3. Reboot phone (or shut down) and when coming on hold Vol Down+Power for a few seconds and let go
4. Boot into TWRP
5. Backup (If you don't have a backup of EVERYTHING at this point, probably a good idea to do so)
---If you do take only EFS
And install file from #3
6. Restart into System
7. Open up your CMD and run this ADB command :
adb devices
adb shell
su (you will get pop up on your phone to give root authorization for ADB, authorize it)
setprop sys.usb.config diag,adb (this will open your OP3 diagnostic port)
Click to expand...
Click to collapse
This forces it into DIAG mode, check your Device Manager to see if you see a port connection displaying a COM PORT.. IF NOT, you need to install drivers--Search thread for drivers, likely will be find in original OPO or OP3 thread.
***********THIS SECTION IS PURELY PRECAUTIONARY*********************** SKIP TO 11 IF YOU WANT
Purely precautionary we did not have to restore any QCN as they do in OP3 due to encryption:
8. Install QPST, open QPST
Now fire up QPST and go to "Port" tab, and choose "Add New Port" ,
9. On "Serial/USB Port" tab, unchecked the option of "Show Serial & USB...bl bla bla" option, you will see your phone listed there as a "COM#" (# is a number depending on your PC) choose it, and click "OK"
10. Now choose "Start Clients" from the Menu tab above, and choose "Software Download"
**********************************************************************************
11. CLOSE QPST. Open up DFS Explorer, when the signup option comes up it is up to you whether or not you want to register for an account (Good to support them since it's a good application) If not, press the X and the app will be there
12. You should see your PORT listed as you did on QPST. Double click on it (If you can't; confirm QPST is closed otherwise you won't be able to connect to the port) You should see it turn green and highlighted ONLINE if you successfully connected
13. Go to the "Band" option then click on "LTE"
14. Press READ; Give it a second and you should see all currently enabled bands listed; If you want to compare you can go to "Network Guru" and press the 3 dots on the top right and press Band Locking and then press LTE.. Should list the same ones
15. Check the additional bands (Just because it says it's enabled, doesn't mean hardware wise it will work due to chipset hardware limitations; This is why as you all do this if you can confirm which bands for you connected and/or didn't connect we can keep a running list.)
16. Press "Write"
17. Since we're in Demo mode it will count down and then in the LOG box you'll see operation successful
18. Restart the phone at this point and disconnect the cable
19. Wait until it boots up again and go to "Network Guru" press the 3 dots again and go to Band Locking and you should see the new bands listed
*If you don't press the 3 dots and press Clear forcings and it'll prompt that a power cycle may occur; That's okay, let it, mine did, wait until the phone comes back up and repeat 19 and the new bands should be listed.
20. LET US KNOW ON THIS THREAD what bands are working, what aren't. It will allow us to further play with the device to discover if there's limitations or if further editing is required like in the OP3.
*Please press THANK YOU if this guide was helpful.
**Sorry for the missing of some info in the guide! Seems when I added the HYPERLINK it removed most of the other text before it so it started at #4 instead of the remainder of #1-3
Direct link to RMT STORAGE PATCH:
Rmt Storage Patch Zip
usb debugging should be enabled i think, you didn't mentioned that. " (this will open your OP3 diagnostic port)" and here should be op2 i think. thanks for thread, i have a2005 and want to unlock 20 band(800mhz), will try asap, now i have exams running out of time. btw, so the risk of breaking phone is low right, this steps only modify EFS partition only? so hybrid recovery and flashfire can backup/restore if enything goes wrong
What is the benefit from this? Better reception?
Sent from my ONE A2005 using Tapatalk
So... Are your at&t bands working now? Which bands specifically?
我從使用 Tapatalk 的 Nexus 9 發送
Still something is missing
Hi, I think something is missing. Let me describe what I have done on a A2005:
1- I downloaded the rmt_storage from the link provided on Pre-reqs #3.
2- I backed up EFS, installed the patched rmt_storage, reboot into system.
3- I installed the modified HTC modem driver as unsigned driver, did the adb diag port commands, and the phone is recognized by DFS.
4- On DFS, I must click on SPC 000000 since the log shows errors. I'm not sure if a specific SPC value is required ***
5- When I click on Read, it captures the values, I wanted to add Band 3 (1800) so I checked it and then clicked on write. The logs showed that the write was successful.
6- I restart the phone, connect it and load adb diag port commands again, load DFS, click on read and the values stay
7- When I open Network Guru on locked LTE bands, the list shows me the previous one, as if nothing has been written. I restarted the phone already several times, still no LTE on Band 3.
Besides the SPC code, I might think that:
- The rmt_storage somehow it's not working
- DFS keeps the values but they are not reflected into Network Guru or phone. I already set 4G/3G/2G enabled on the connectivity options. No changes
- Maybe there is another value that needs to be changed with another tool such as QXDM
Any help would be very appreciated!!!
haroldgv said:
Hi, I think something is missing. Let me describe what I have done on a A2005:
1- I downloaded the rmt_storage from the link provided on Pre-reqs #3.
2- I backed up EFS, installed the patched rmt_storage, reboot into system.
3- I installed the modified HTC modem driver as unsigned driver, did the adb diag port commands, and the phone is recognized by DFS.
4- On DFS, I must click on SPC 000000 since the log shows errors. I'm not sure if a specific SPC value is required ***
5- When I click on Read, it captures the values, I wanted to add Band 3 (1800) so I checked it and then clicked on write. The logs showed that the write was successful.
6- I restart the phone, connect it and load adb diag port commands again, load DFS, click on read and the values stay
7- When I open Network Guru on locked LTE bands, the list shows me the previous one, as if nothing has been written. I restarted the phone already several times, still no LTE on Band 3.
Besides the SPC code, I might think that:
- The rmt_storage somehow it's not working
- DFS keeps the values but they are not reflected into Network Guru or phone. I already set 4G/3G/2G enabled on the connectivity options. No changes
- Maybe there is another value that needs to be changed with another tool such as QXDM
Any help would be very appreciated!!!
Click to expand...
Click to collapse
what and where is PRE-REQ #3?
haroldgv said:
Hi, I think something is missing. Let me describe what I have done on a A2005:
1- I downloaded the rmt_storage from the link provided on Pre-reqs #3.
2- I backed up EFS, installed the patched rmt_storage, reboot into system.
3- I installed the modified HTC modem driver as unsigned driver, did the adb diag port commands, and the phone is recognized by DFS.
4- On DFS, I must click on SPC 000000 since the log shows errors. I'm not sure if a specific SPC value is required ***
5- When I click on Read, it captures the values, I wanted to add Band 3 (1800) so I checked it and then clicked on write. The logs showed that the write was successful.
6- I restart the phone, connect it and load adb diag port commands again, load DFS, click on read and the values stay
7- When I open Network Guru on locked LTE bands, the list shows me the previous one, as if nothing has been written. I restarted the phone already several times, still no LTE on Band 3.
Besides the SPC code, I might think that:
- The rmt_storage somehow it's not working
- DFS keeps the values but they are not reflected into Network Guru or phone. I already set 4G/3G/2G enabled on the connectivity options. No changes
- Maybe there is another value that needs to be changed with another tool such as QXDM
Any help would be very appreciated!!!
Click to expand...
Click to collapse
In Network Signal Guru, choose clear forcing. And check the LTE bands again,
or, install Network Signal Guru after you done unlocking, else it will show what it remember on previous set up
---------- Post added at 01:44 PM ---------- Previous post was at 01:43 PM ----------
chxei said:
what and where is PRE-REQ #3?
Click to expand...
Click to collapse
the guide forget to mention that u need to flash rmt storage patch before do any modification,
else no mod will be saved (will revert upon boot)
the patch is in my OP3 thread
Thanks! So today's update:
1- I connected the phone again, ran adb commands, reviewed the bands again on DFS tool and settings stayed. I'm pursuing to enable Band 3
2- I uninstalled Network Signal Guru
3- On Recovery, flashed again the patched rmt_storage, boot the phone, wrote the values again on DFS tool. Reboot phone
4- I installed Network Signal Guru and now it's showing up on the bands lists. I unchecked the bands default on A2005 and used the ones from Eruper/Asia Model as FDD-LTE: Bands 1/3/5/7/8/20 and TDD-LTE: Bands 38/40/41. My provider in Costa Rica (Movistar) uses Band 3 (1800) for their LTE. I clicked on Band locking, clicked on GSM and WDCMA and removed all checks. Then clicked on LTE and left all LTE bands in hopes that it will connect to that frequency. The list shows:
B1: 2100
B3: 1800+
B5: 850
B7: 2600
B8: 900 GSM
B20: 800 DD
B38: TDD2600
B40: TDD 2300
B41: TDD 2500
When I only picked LTE bands as checked, it never resovled to get connected to any cell base.
5- I dialed *#*#4636#*#* to access the information about the phone and monitored the signal setting it up to "LTE Only". No signal on that either
Top of my head, I will restore the qcn backup I made and restore the backup I made for EFS and start again. Now it's saving values after reboot, which is great, but not identifying anything.
Is there any log worth posting here? I read on the OP3 guide that they were restoring a qcn file with bands enabled. Is it worth trying the same?
Anyone that has LTE band 3 enabled would be very appreciated if they post their qcn backup
t99220475 said:
So... Are your at&t bands working now? Which bands specifically?
我從使用 Tapatalk 的 Nexus 9 發送
Click to expand...
Click to collapse
I have not been able to further test as all the phones I compare to that are also AT&T ie: AT&T S6 are connected to the same Bands as me so cannot test til I get to an area where other bands are available currently. Will report back as I can test, but was hoping others can test in the mean time as well.
haroldgv said:
Thanks! So today's update:
Click to expand...
Click to collapse
You shouldn't need to restore any QCN or EFS, just re-check the bands you unchecked and it should pickup all the bands again. Also, confirm your APN is correct to be used with LTE?
Did you get ANY LTE Bands before this mod? Or you only have LTE on Band3?
You can use RAT locking to enable LTE Only rather than unchecking all the WCDMA and GSM bands. that way it'll force LTE, if it doesn't go to the Cellular Network tab and press the Preferred NETWORK to go to LTE ONLY.
sadly for me nothing happened, i have a2005 and want to add band 3 and band 20, did everything 2-3 times whats in a guide, everything went well, write process was comlete but bands didn't added
When you say didn't add, you don't see them in network guru or you see then, but unable to catch signal on them?
aurfawce said:
When you say didn't add, you don't see them in network guru or you see then, but unable to catch signal on them?
Click to expand...
Click to collapse
both, not shown in neywork guru, nor lte signal
chxei said:
both, not shown in neywork guru, nor lte signal
Click to expand...
Click to collapse
You tried to force clear in network guru? If so, when you reconnect and enter diag mode and go to DFS, press bands and LTE, press read, did the changes you made stick?
Just so ppl around here know... there is old forum about band OPT band unlocking with various trials of changing bands, which failed, due to missing RMT patch OR BUT it got MANY juicy info !!!
in the past other users sent me qcn/qcnx files of the EU and CN models ( credit: whoever sent me these files from the old thread ) - I hope this help you out.
keep up the good work ! :good:
gps3dx said:
Just so ppl around here know... there is old forum about band OPT band unlocking.
( un-successful of course due to missing RMT patch OR modem ( on A2005=US) ) with juicy info.
in the past other users sent me qcn/qcnx files of the EU and CN models ( credit: whoever sent me these files from the old thread ) - I hope this help you out.
keep up the good work ! :good:
Click to expand...
Click to collapse
Have you tried what we said here? And tried to see if you can band lock on 3?
I'm going to see the qcn based off of the op3 guide as well as they had to do qcn restoring.
aurfawce said:
Have you tried what we said here? And tried to see if you can band lock on 3?
I'm going to see the qcn based off of the op3 guide as well as they had to do qcn restoring.
Click to expand...
Click to collapse
not yet...it will take me some time, i'm a master's student in exam period.
nontheless, as you can see from the old forum, i'm really interested in opening LTE band 3 on my A2005.
Thanks guys! I live in Venezuela and we use band 3 for LTE and I have the EU version. I'll try this guide today
EDIT: I tried without success, I did all the process but i do not have LTE signal on Band 3. On Network Guru, Band 3 appears as supported. I tried RAT locking but It keeps without signal.
gps3dx said:
Just so ppl around here know... there is old forum about band OPT band unlocking with various trials of changing bands, which failed, due to missing RMT patch OR BUT it got MANY juicy info !!!
in the past other users sent me qcn/qcnx files of the EU and CN models ( credit: whoever sent me these files from the old thread ) - I hope this help you out.
keep up the good work ! :good:
Click to expand...
Click to collapse
Thank you for the qcn files. I've tried it, and it overwrites my imei, which is expected. Then I tried to replace the imei with mine by hex editor, but flashing the modified qcn still overwrites my imei. We may get into the same trouble with op3, which is the imei encryption.

[Guide] Enabling additional LTE Bands on the Galaxy S7 with U firmware

Enabling additional LTE Bands on the Galaxy S7 with U firmware (Root not required) (North American Qualcomm S7)​
In this guide, I will guide you on the steps that are needed to enable additional LTE bands on your SM-G930U device and allow you to use LTE if your carrier uses an LTE band that is not supported out of the box by the U firmware. This guide may work for the Sprint, T-Mobile, AT&T, Verizon, US Cellular and Tracfone variants of the S7. For this guide, I will enable LTE band 17 for use with my local carrier here in Belize.
Ready? Cool!
Disclaimers:
I am not responsible for any bricked devices
Even though this process does not void or trip Knox warranty, you can never be too sure of what can happen, these steps have been done multiple times by me and have not experienced any issues at all.
Follow this guide at your own risk.
Things you will need:
1. Windows PC (Windows Vista, Windows 7/8/10)
2. USB Data Cable
3. USB 2.0 Port (have not tried on a USB 3.0 Port)
4. Samsung USB Drivers
5. Install (disconnect your PC from Internet once installed) CDMA Tool
6. USA Sim Card (Can be from AT&T, T-Mobile, or Tracfone, have not tried with Verizon or Sprint SIMs) With the Android Oreo Update, you no longer need to insert a US based sim card, to enable Diagnostic Mode, just dial *#0808#.
Procedures:
1. Eject your Sim card if it’s not one of the above (If you have a SIM from one of above carriers, skip this step) (UPDATE 8/6/2018, NO LONGER NEEDED TO INSERT US BASED SIM CARD IF YOU ARE ON ANDROID OREO)
2. Insert an AT&T, T-Mobile or Tracfone SIM and wait a few seconds, a pop-up like this one will appear, tap OK. Your Device will reboot after a few minutes. (UPDATE 8/6/2018, NO LONGER NEEDED TO INSERT US BASED SIM CARD IF YOU ARE ON ANDROID OREO)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3. Once Reboot, go to the phone dialer, enter *#0808#, a USB Settings screen like this will appear. Click your home button to go directly to your home screen, do not click back.
4. Remove Sim Card, insert your carrier sim and reboot the device without closing the USB Settings (if your carrier is one of the above skip this step)
5. Once rebooted, click on the app switcher, select usb settings app, tap on DM + MODEM + ADB, tap Reboot. (do not close the USB Settings app yet you will need it again)
PC STEPS
6. Once booted, connect device to PC, wait for it to install all the drivers, verify it on device manager.
7. At this point you should be disconnected from your internet connection. MUST DISCONNECT!
8. Fire up DFS Tools folder on your desktop, double click on Qualcomm Tool
9. It will ask for login but ignore it, select your Samsung Mobile USB Serial port to connect DFS to your device.
10. Click Band Tab>LTE tab>click read, click read again.
11. Check your LTE band you want to enable (do note that some of these bands may not work. For this guide, I will be enabling LTE band 17 (700).
12. Click on write, click yes/ok on warning diag, wait for timer to go down and it writes the changes to your device.
13. Reboot your S7, connect it again to DFS and verify band was written successfully to the NV by going back to the LTE tab and clicking “read”.
14. If the band you enabled stays checked, disconnect your device at this point from PC, if the check goes away, it may mean that band is not supported in the U firmware.
15. Dial *#0011# and verify your device is connected to LTE. See below images:
17. Switch to the USB settings app, select MTP, Tap reboot. Once booted again you can now close it.
18. Say thanks if successful.
Before:
After:
Donate if you want to
https://www.paypal.me/micallan17
So this should work on all Samsung qualcomm phones correct?
Sent from my SM-G930P using Tapatalk
Dvalin21 said:
So this should work on all Samsung qualcomm phones correct?
Sent from my SM-G930P using Tapatalk
Click to expand...
Click to collapse
It may work, this was done on an S7, i have not tried this on any other samsung device.
OK thanks
Sent from my SM-G930P using Tapatalk
Will this work on stock firmware with Boost(Sprint)?
---------- Post added at 10:14 PM ---------- Previous post was at 09:28 PM ----------
weichengjlkd said:
Will this work on stock firmware with Boost(Sprint)?
Click to expand...
Click to collapse
Never mind, it worked but should I enable all LTE bands for my carrier?
weichengjlkd said:
Will this work on stock firmware with Boost(Sprint)?
---------- Post added at 10:14 PM ---------- Previous post was at 09:28 PM ----------
Never mind, it worked but should I enable all LTE bands for my carrier?
Click to expand...
Click to collapse
i think it should work, try it and see what happens?
micallan_17 said:
i think it should work, try it and see what happens?
Click to expand...
Click to collapse
I did it, does enabling some of them cause more battery drain? and I've seen posts where people say it could cause hardware problems is that true?
weichengjlkd said:
I did it, does enabling some of them cause more battery drain? and I've seen posts where people say it could cause hardware problems is that true?
Click to expand...
Click to collapse
It maybe can cause issues, for me i just enabled one extra band which is band 17. I didn't enable anything else because i don't really need them. My battery seems the same to be honest.
micallan_17 said:
Enabling additional LTE Bands on the Galaxy S7 with U firmware (Root not required) (North American Qualcomm S7)
In this guide, I will guide you on the steps that are needed to enable additional LTE bands on your SM-G930U device and allow you to use LTE if your carrier uses an LTE band that is not supported out of the box by the U firmware. This guide may work for the Sprint, T-Mobile, AT&T, Verizon, US Cellular and Tracfone variants of the S7. For this guide, I will enable LTE band 17 for use with my local carrier here in Belize.
Ready? Cool!
Disclaimers:
I am not responsible for any bricked devices
Even though this process does not void or trip Knox warranty, you can never be too sure of what can happen, these steps have been done multiple times by me and have not experienced any issues at all.
Follow this guide at your own risk.
Things you will need:
1. Windows PC (Windows Vista, Windows 7/8/10)
2. USB Data Cable
3. USB 2.0 Port (have not tried on a USB 3.0 Port)
4. Samsung USB Drivers
5. Install (disconnect your PC from Internet once installed) CDMA Tool
6. USA Sim Card (Can be from AT&T, T-Mobile, or Tracfone, have not tried with Verizon or Sprint SIMs)
Procedures:
1. Eject your Sim card if it’s not one of the above (If you have a SIM from one of above carriers, skip this step)
2. Insert an AT&T, T-Mobile or Tracfone SIM and wait a few seconds, a pop-up like this one will appear, tap OK. Your Device will reboot after a few minutes.
3. Once Reboot, go to the phone dialer, enter *#0808#, a USB Settings screen like this will appear. Click your home button to go directly to your home screen, do not click back.
4. Remove Sim Card, insert your carrier sim and reboot the device without closing the USB Settings (if your carrier is one of the above skip this step)
5. Once rebooted, click on the app switcher, select usb settings app, tap on DM + MODEM + ADB, tap Reboot. (do not close the USB Settings app yet you will need it again)
PC STEPS
6. Once booted, connect device to PC, wait for it to install all the drivers, verify it on device manager.
7. At this point you should be disconnected from your internet connection. MUST DISCONNECT!
8. Fire up DFS Tools folder on your desktop, double click on Qualcomm Tool
9. It will ask for login but ignore it, select your Samsung Mobile USB Serial port to connect DFS to your device.
10. Click Band Tab>LTE tab>click read, click read again.
11. Check your LTE band you want to enable (do note that some of these bands may not work. For this guide, I will be enabling LTE band 17 (700).
12. Click on write, click yes/ok on warning diag, wait for timer to go down and it writes the changes to your device.
13. Reboot your S7, connect it again to DFS and verify band was written successfully to the NV by going back to the LTE tab and clicking “read”.
14. If the band you enabled stays checked, disconnect your device at this point from PC, if the check goes away, it may mean that band is not supported in the U firmware.
15. Dial *#0011# and verify your device is connected to LTE. See below images:
17. Switch to the USB settings app, select MTP, Tap reboot. Once booted again you can now close it.
18. Say thanks if successful.
Before:
After:
Click to expand...
Click to collapse
How did u flash g930p to g930u I had errors
Why more LTE bands ?
OK, please fill me in, I have u firmware and hotspot and I love it. I rooted my old phones and know enough to probably brick a phone although fortunatly I never have...Knock,knock... Why do I want more LTE bands, I travel over the road all the time and I am constantly in and out of signals, will this help my data, or signal in remote areas or am I totally lost here?
macmovr said:
OK, please fill me in, I have u firmware and hotspot and I love it. I rooted my old phones and know enough to probably brick a phone although fortunatly I never have...Knock,knock... Why do I want more LTE bands, I travel over the road all the time and I am constantly in and out of signals, will this help my data, or signal in remote areas or am I totally lost here?
Click to expand...
Click to collapse
How did u flash the u firmware for Sprint varient
miko12312 said:
How did u flash the u firmware for Sprint varient
Click to expand...
Click to collapse
Odin.
YMNDLZ said:
Odin.
Click to expand...
Click to collapse
I am on nougat for g930p what version am I able to flash
miko12312 said:
I am on nougat for g930p what version am I able to flash
Click to expand...
Click to collapse
You'd need to go flash the G930P PL6 firmware and then flash the universal PL2.
YMNDLZ said:
You'd need to go flash the G930P PL6 firmware and then flash the universal PL2.
Click to expand...
Click to collapse
The only pl2 firmware I find is one on androidfile host but at the end of the file name.it say vzw meaning Verizon if I'm correct ?
miko12312 said:
The only pl2 firmware I find is one on androidfile host but at the end of the file name.it say vzw meaning Verizon if I'm correct ?
Click to expand...
Click to collapse
Yup it means verizon wireless.
Here's the PL2: http://updato.com/firmware-archive-select-model?record=8EEC48FCD72711E69215FA163EE8F90B
And here's the PL6: http://updato.com/firmware-archive-select-model?record=5BFA1AC0E81511E69215FA163EE8F90B
Hit thanks on my posts if they helped.
YMNDLZ said:
Yup it means verizon wireless.
Here's the PL2: http://updato.com/firmware-archive-select-model?record=8EEC48FCD72711E69215FA163EE8F90B
And here's the PL6: http://updato.com/firmware-archive-select-model?record=5BFA1AC0E81511E69215FA163EE8F90B
Hit thanks on my posts if they helped.
Click to expand...
Click to collapse
I'll let you know if they work I have the Sprint firmware just need a working u firmware hopefully I can get this phone working for att
YMNDLZ said:
Yup it means verizon wireless.
Here's the PL2: http://updato.com/firmware-archive-select-model?record=8EEC48FCD72711E69215FA163EE8F90B
And here's the PL6: http://updato.com/firmware-archive-select-model?record=5BFA1AC0E81511E69215FA163EE8F90B
Hit thanks on my posts if they helped.
Click to expand...
Click to collapse
Worked perfectly I'm unlocked now hopefully soon to try for att, have you already rooted the qc1 update I think it's called
Flashing u firmware allows the userof any sim card flash u firmware through Odin and place the sim card desired to use, and it will give a confirmation to restart the device. It will then load into the recovery and setup the sim automatically, WiFi calling features are enabled also
YMNDLZ said:
Yup it means verizon wireless.
Here's the PL2: http://updato.com/firmware-archive-select-model?record=8EEC48FCD72711E69215FA163EE8F90B
And here's the PL6: http://updato.com/firmware-archive-select-model?record=5BFA1AC0E81511E69215FA163EE8F90B
Hit thanks on my posts if they helped.
Click to expand...
Click to collapse
Can u put the stock pl2 boot image flaahble for Odin just the boot.img

Categories

Resources