Im about to give up. I can get recovery thru adb, quick boot app, rom manager, etc. I still have yet to boot recovery manually. I want to be ready for cm6, which means I need a manual recovery method in case my vibrant freezes up or bootloops so I can restore backup. I've tried every vol-up vol-down combo I could find. Still, after 2 weeks, no manual recovery. I don't want to go back to the unrooted life, but without a manual recovery method, I dont want to chance freezing up. Is there any other method of getting to recovery if the phone freezes up after flashing a rom?
I don't see how that's even possible... Just to make sure you are:
1. Turning off the phone
2. Holding the two volume buttons down
3. Then pressing the power button along with the volume buttons until the "vibrant" logo comes up, goes away and comes back and then letting go of all buttons...
It's pretty easy to do it... But if you did that and you are still getting nothing I suggest you do a factory reset and try again...
If not, try and take it in to a T-Mobile store... This is a function all stock phones should have, and if you can't go into it, that's a defect.
I hold my phone horizontal when powered off.
Both thumbs on the volume rocker.
Press and hold power and volume buttons.
When the Vibrant logo comes up, release power, keep holding the volume rocker.
I've never had an issue. It does seem like a lot of new posts popping up with this issue though. I use Quick Boot now that I am rooted. I also use Clockwork Recovery too.
There's definately a problem with some phones. I had one that wouldn't boot to recovery or download using the buttons. I took it in and swapped it out, and when I tried the new phone in the store I got it first try. It's just not that tricky to do.
Well, after another whole day of research and attempts, I give up. Sending the phone back and tmobile is shipping me another. Only problem is I cant try it out for recovery first. Hope this one works out.
Hello,
I purchased a second hand Samsung S3 i9300 with a cracked gorilla glass, but the touch works perfectly. When the guy showed me the phone it was working perfectly. When he was going to give me the phone, he removed the battery to get his SIM card out and then put the battery back in. When the phone restarted it said Safe Mode in the bottom left corner. When I got home I started checking the phone a little better and started looking the internet to see how to get out of safe mode. I have tried everything I have found. I have restarted the phone, I have shut it off and turning it back on, I have removed the battery, SIM, SD card and reboot, nothing. One thing I should mention is that the Volume Up key works perfectly when I'm inside the OS, but when I go to Download Mode (to flash with Odin) I'm unable to Continue from the main screen (it asks me to press the Volume Up key to continue but the key is unresponsive). I have also tried recovery mode, but again, I need to hold the Volume Up key and I do, but the phone boots normally and is still in safe mode. Even a Factory Reset hasn't fixed my problem. The phone is running JB 4.3 and my first thought was that maybe the update was not made correctly by the previous owner, but I can't find a way to downgrade to 4.1 or 4.2 because of the issue with the Volume Up key outside the OS. Please Help!!!
You start by reading the faqs and guides .
This question posted multiple times Safe Mode .
http://forum.xda-developers.com/showpost.php?p=28315455&postcount=2
But judged by your problems you need a service repair .
Well I was undervolting and underclocking my i9100 for a few months and it would suffer from freezes and stuff like that nothing much as I would be able to perform a hard reset and reboot with my phone completely working everytime that happens. However today, I just locked my phone after taking a picture and I could not unlock it after that. I pressed the power button and home button but the screen would not turn on. So i just took out the battery and tried booting the phone. It was stuck in a bootloop where the boot animation would just keep on playing. So i force shutdown it and booted it into recovery. I had CWM 6.0.4.6 installed and when i booted into recovery, it gave me the message it cannot mount something and cannot load last kmsg and blah. I took no notice and tried to format cache. During this point, the recovery hanged and i force shutdown my phone again. After which, I could never turn on my phone again. No splash screen no nothing. I think it is bricked. And yea btw my usb port is not working anymore and it can only be used for charging. And i was running cm11 infected. Can you all please help me thanks!
so no recovery nor download mode?
Sadly, no
TheImpossibleEnemy said:
so no recovery nor download mode?
Click to expand...
Click to collapse
Yep i cannot even boot into anything no splash screen no nothing pressed the power button for like so long i even removed the battery for 2 hours and popped it back in not working
Try this - take out battery,then press and hold volume down+home+power and put battery back without releasing buttons.This may get you into a download mode where you can flash stock jb via odin.
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
Check and make sure that your volume buttons and home button are not stuck also. If they are not, I would suggest a visit to a repair shop as your EMMC chip might be weak already.
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
As said your emmc chip maybe failing.
The dead boot thread maybe of interest to you.
Virnik0 said:
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
Click to expand...
Click to collapse
He said he has tested this and can also hear the micro-switch clicking.
scorpionhd2 said:
Check and make sure that your volume buttons and home button are not stuck also. If they are not, I would suggest a visit to a repair shop as your EMMC chip might be weak already.
Click to expand...
Click to collapse
Virnik0 said:
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
Click to expand...
Click to collapse
Darke5tShad0w said:
As said your emmc chip maybe failing.
The dead boot thread maybe of interest to you.
He said he has tested this and can also hear the micro-switch clicking.
Click to expand...
Click to collapse
Thank you very much for helping! :good:
So the question is, whether it's the power button's or emmc's fault...
I did a little searching and found this video. I've got exactly the same problem like the guy. At 1:06 following the boot loop, at 1:34 following the problem with downlod mode.
Although he thinks it's caused to the sudden death problem, but at least in my case I think it's wrong because months ago I did the eMMC Brickbug Check.
Also I noticed a probably important detail. When I put the battery in the phone, it automatically turns on without pressing the power button like in 1:04-1:09 in the video. Which normal working phone turns itself on by simply putting in the battery...?
So it must get a command for turning on - (possibly through a defect power button?)
@Virnik0, do you remember, if you could hear the micro-switch clicking on your phone before replacing the button on the mainboard?
beginnerteur said:
Also I noticed a probably important detail. When I put the battery in the phone, it automatically turns on without pressing the power button
Click to expand...
Click to collapse
Your power button is faulty, replace it before you try fixing anything else.
Thank you very, very much for helping! :good: :good: :good:
Truly the power button was fault although you could hear clearly the "click".
I unsoldered and removed the power module and (by startig with JIG and rebooting via ADB) the phone works as it should. :victory:
Now I'm trying to solder a new power button......it's a bit tricky
Again, thank you very much guys!
I had the same problem, pressed the button many times, and it helped. Thank you for your suggestions
How the problem occurred
So a year or two ago I bought a Jiayu G4A/T/Whatever they're calling it and safely got it here. I've used the stock ROM for a bit but I wanted to get rid of the bloatware that was still on it, so I eventually ended up with a properly rooted phone with a ROM from Jiayu.es (Everything worked, have ClockworkMod as recovery, accessible via Mobileuncle Tools), which was essentially a stock Kitkat rom made to work for the phone. Now I got sick of the ROM and recently saw the new EMUI version on Huawei's P8 Lite, so I figured I'd look around for a tailored ROM running that, and ended up at "jiayu-emui-3-0-stable" from Needrom.
What I did
1. I downloaded a ROM from Needrom with identifier "jiayu-emui-3-0-stable" (I can't post external links)
2. Backed up my important files following a guide from androidcentral titled "[Guide] How to Backup and Restore Apps and Data when installing new ROMs" that I can't link,and did a full backup using CWM
3. Placed the ZIP on my internal SD card, went into recovery, wiped data/cache (not dalvik, since it wasn't described in the instructions, I think this might be a probable cause) and installed the new ROM from ZIP
4. Rebooted the phone and now it's stuck in the boot loop I mentioned.
What the problem is
Bootloops aren't that much of a problem usually, except this one is... I can't get into recovery mode. From there on it'd be cake, since I made the right preparations, but I can't get into it. While connected to my PC it keeps powering on, showing a splash screen from Jiayu.es briefly (which shouldn't be present anymore) and powering off after 10 seconds, only to come back to the splash screen.
What I've tried
I've unplugged it, removed the battery, waited to get a full power cycle and tried to hold my buttons in these combinations: [power button + volume up], [power button + volume down] - but neither work. It just keeps going with the boot loop. I can succesfully power it down, and when I plug it in from there it shows the low battery image. At the moment of seeing that I thought I could connect to it using ADB / Fastboot, but no luck there either. It keeps saying no devices found, and with fastboot it keeps on <waiting for device>.
My questions
What exactly can I do if there is no way for me to get into recovery mode? Are there any alternatives? How can I get my device to be recognized by ADB? Is that even possible? Why is this bootloop any different from others?
Update from the massive Q&A thread:
ZipAddict said:
Is it booting up on its own too after being off? This happened to wifes phone and it turned out the power button was stuck. I took a pencil and hit the power button with the eraser a few times and it worked then. Her case mustve dislogded it. I will keep my fingers crossed for u. If not send me a private message and i will look for an answer tomorrow and get back with u
Click to expand...
Click to collapse
Thank you for the reply!
Yes, it does. I took the battery out and let it lay disassembled for a night, after which I cleaned it a little and re-inserted the battery. With the case back on, nothing happened, so the power button wasn't stuck for sure. When I powered it back on with the power button (no USB attached) it showed the emblem for ~8 seconds and powered off. It then buzzes to show it's powered on again and up comes the splash screen again. Could it be that the ROM was just a rebooting falsehood? Why would it disallow me getting into recovery mode? I really hope there is something that can still force the device into recovery mode / interact with it somehow while in this state.
Oh, I also tried to see if the volume down button was broken but all the contacts seem intact, plus, they worked an hour before I started switching roms.