Related
Recently, I bought a xiaomi redmi note 3 with the 650 version. I switch to Miui 8 China Fastboot Room from a Global Fastboot Rom, also for unlocking the bootloader. But after I have finished my flashing, it turns out that the Note 3 can't turn on, Stucking on the MI logo for 2 times then turns off again. I tried connecting it to the PC, but the led blinks red. I tried to flash the Miui again but it doesn't show the device. My PC recognized the port as Qualcomm HS-USB Diagnostics 900E, but I can't take it to EDL mode. I tried entering it from the Fastboot mode but still didn't work. Any Help?
*P.S: It also blinks red when I entered the Fastboot Mode
Just checking, but did you use the fastboot edl v2 to enter EDL?
danted7 said:
Recently, I bought a xiaomi redmi note 3 with the 650 version. I switch to Miui 8 China Fastboot Room from a Global Fastboot Rom, also for unlocking the bootloader. But after I have finished my flashing, it turns out that the Note 3 can't turn on, Stucking on the MI logo for 2 times then turns off again. I tried connecting it to the PC, but the led blinks red. I tried to flash the Miui again but it doesn't show the device. My PC recognized the port as Qualcomm HS-USB Diagnostics 900E, but I can't take it to EDL mode. I tried entering it from the Fastboot mode but still didn't work. Any Help?
*P.S: It also blinks red when I entered the Fastboot Mode
Click to expand...
Click to collapse
when i fail to unlock bootloader in official method then i tried miui8 flashboot Rom from mi flash tool with modified emmc_appsboot.mbn file from one of the developer i bricked my Redmi note 3 Qlcmm650
solution:- 1) remove back cover & disconnect the battery around 1 minute reconnect it (recomended one if this not possible for you then try 2nd method)
Or
2)full discharge the battery Then charge it more then 35% (it will also work as diconnecting the battery)
connect the computer &and press volume + & - button together
connect the PC & vol buttons press both are at the same time then you enter the correct EDL mode (same red light but this time correct EDL mode you can flash the rom use official Fastboot rom Dont modify the contents)
if i helped you hit thanks
I was in same situation today: Mobile doesnt do anything else then red-blinking, no edl or fastboot. Pc only saw "Qualcomm HS-USB Diagnostics 900E".
Found the solutions mentioned by Chinmayhegde, but i didnt get the cover off the device and dont want to damage new mobile.
then i found the method "Deep Flash".
its small manipulation of usb-cable: put a small wire on second terminal, put in pc and then pull the wire.
i succeded after second try. then pc sees "Qualcomm HS-USB QDLoader 9008" again and miflash is able to flash the device.
see this tutorial for creating the modded usb cable: http://en.miui.com/thread-310325-1-1.html
Hope it works
if your phone still able to enter fastboot, you can try to use fastboot to edl v2 to enter download mode
if it still not help, most safe & easy mode is using deep flash cable as above post
I have same problem.
Even I try booting fastboot mod but it keeps restarting.
Even fastboot logo comes by just pressing volume down button. So I think power button is stuck. That's make phone restart all the time.
How to overcome this problem?
Thanks
Sent from my SM-G900I using XDA-Developers mobile app
I fix my phone.
Open back cover and undo power cable flex and battery connctor from motherboard and put back after 1 min.
Phone started normal.
thanks
Sent from my SM-G900I using XDA-Developers mobile app
danted7 said:
Recently, I bought a xiaomi redmi note 3 with the 650 version. I switch to Miui 8 China Fastboot Room from a Global Fastboot Rom, also for unlocking the bootloader. But after I have finished my flashing, it turns out that the Note 3 can't turn on, Stucking on the MI logo for 2 times then turns off again. I tried connecting it to the PC, but the led blinks red. I tried to flash the Miui again but it doesn't show the device. My PC recognized the port as Qualcomm HS-USB Diagnostics 900E, but I can't take it to EDL mode. I tried entering it from the Fastboot mode but still didn't work. Any Help?
*P.S: It also blinks red when I entered the Fastboot Mode
Click to expand...
Click to collapse
Try To Remove Your Battery than Use MiFlash Tool To Flash Your Mobile Bro.
Hi, so I have encountered a rather big issue with my xiaomi redmi 3 pro.
I believe I have flashed wrong (corrupted ? ) ROM, now I have a really annoying situation.
So, I flashed " ido_xhdpi_images_V7.2.6.0.LHPCNDB_20160129.0000.14_5.1_cn " in MiFlash, took a bit long time (nearly 15 minutes), afterwards it was completed, I disconnected my phone, and *BOOM* since then, black.
Current situation is this: When I connect my phone via USB, my phone gets recognized in device manager as
"Qualcomm HS-USB QDLoader 9008 (COM#)", also it gets recognized in MiFlash, but can't get it to work in fastboot, and it is not recognized as adb device. So, throughout 3 days now, I tried nearly EVERYTHING I have found on forums. The only thing I have not done is to take the back cover off and disconnect battery ( as I have seen on forums), tried with deep flash cable, all possible combinations of buttons and all. If the phone is connected to PC, when I press whatever combination of buttons on phone I just get Windows sound for connecting an USB device.
So today, when I connected it, red LED light was blinking, I have no idea what that was, so I plugged it into the wall to charge for 10mins, and now when I connect it, it's gone again, all black, no response whatsoever.
So, when I connect it to MiFlash and try to flash any ROM, tried nearly everyone I found, I get the same message; "Unspecified error 0x80004005; End Transfer packet id0, status 9" if I refresh MiFlash without disconnecting, and press flash again I get "Reached the end of the file. (0x80070026; Receiving hello packet) "
Things maybe to mention: I am running a 64 bit Windows 10, and my bootlocker is locked.
So I am wondering, if there is any possible way to solve this or it's time for a new phone?
alchzor said:
Hi, so I have encountered a rather big issue with my xiaomi redmi 3 pro.
I believe I have flashed wrong (corrupted ? ) ROM, now I have a really annoying situation.
So, I flashed " ido_xhdpi_images_V7.2.6.0.LHPCNDB_20160129.0000.14_5.1_cn " in MiFlash, took a bit long time (nearly 15 minutes), afterwards it was completed, I disconnected my phone, and *BOOM* since then, black.
Current situation is this: When I connect my phone via USB, my phone gets recognized in device manager as
"Qualcomm HS-USB QDLoader 9008 (COM#)", also it gets recognized in MiFlash, but can't get it to work in fastboot, and it is not recognized as adb device. So, throughout 3 days now, I tried nearly EVERYTHING I have found on forums. The only thing I have not done is to take the back cover off and disconnect battery ( as I have seen on forums), tried with deep flash cable, all possible combinations of buttons and all. If the phone is connected to PC, when I press whatever combination of buttons on phone I just get Windows sound for connecting an USB device.
So today, when I connected it, red LED light was blinking, I have no idea what that was, so I plugged it into the wall to charge for 10mins, and now when I connect it, it's gone again, all black, no response whatsoever.
So, when I connect it to MiFlash and try to flash any ROM, tried nearly everyone I found, I get the same message; "Unspecified error 0x80004005; End Transfer packet id0, status 9" if I refresh MiFlash without disconnecting, and press flash again I get "Reached the end of the file. (0x80070026; Receiving hello packet) "
Things maybe to mention: I am running a 64 bit Windows 10, and my bootlocker is locked.
So I am wondering, if there is any possible way to solve this or it's time for a new phone?
Click to expand...
Click to collapse
Hello,
I will move your thread to the correct section so that the experts there maybe able to assist you.
Regards
Vatsal,
Forum Moderator.
Hi, sorry to hear that happened to you. I suggest you to post this on Xiaomi reddit page, so more people can help you. Here is the link:
https://www.reddit.com/r/Xiaomi/
Hey, i have a Xiaomi Note 3 Pro Kenzo and one day he just turned off and never went back again. When i plug it on pc, it just shows black screen, flashes the red light multiple times and it's recognized as Qualcomm HS-USB Diagnostics 900E.
I've already searched online and seems that my phone is stuck on EDL mode, so I made it go to the real EDL mode that allows me to flash it a new rom. I managed to make my pc recognize as Qualcomm 9008.
Beeing that, I tried to flash a rom but at the mi flash 20160330 it gets stuck on: "send nop command" forever and at the mi flash 2170425 it gets the error : "<?xml version="1.0" encoding="UTF-8" ?><data><log value="init storage:fail " /></data> "
I've got another redmi note 3 pro, and I can flash it, so I don't there's any problem with my computer, but the info is:
Windows 10 Pro 64x
Safe Drivers Disable
If anyone can help...
gustavoabonare said:
Hey, i have a Xiaomi Note 3 Pro Kenzo and one day he just turned off and never went back again. When i plug it on pc, it just shows black screen, flashes the red light multiple times and it's recognized as Qualcomm HS-USB Diagnostics 900E.
I've already searched online and seems that my phone is stuck on EDL mode, so I made it go to the real EDL mode that allows me to flash it a new rom. I managed to make my pc recognize as Qualcomm 9008.
Beeing that, I tried to flash a rom but at the mi flash 20160330 it gets stuck on: "send nop command" forever and at the mi flash 2170425 it gets the error : "<?xml version="1.0" encoding="UTF-8" ?><data><log value="init storage:fail " /></data> "
I've got another redmi note 3 pro, and I can flash it, so I don't there's any problem with my computer, but the info is:
Windows 10 Pro 64x
Safe Drivers Disable
If anyone can help...
Click to expand...
Click to collapse
Seems like a problem with the emmc chip. Get the device checked to make sure that your emmc is not faulty. If the emmc is safe, contact me and I'll help. Until then good luck.
Archit9169 said:
Seems like a problem with the emmc chip. Get the device checked to make sure that your emmc is not faulty. If the emmc is safe, contact me and I'll help. Until then good luck.
Click to expand...
Click to collapse
Thx for the reply man, the problem is that i live in Brazil, we don't have Xiaomi assistance, so I don't have a place to get it checked ;x.
But yeah, I saw in other forums that this migth be a EMMC problem
gustavoabonare said:
Thx for the reply man, the problem is that i live in Brazil, we don't have Xiaomi assistance, so I don't have a place to get it checked ;x.
But yeah, I saw in other forums that this migth be a EMMC problem
Click to expand...
Click to collapse
Forget about warranty, get it checked at a local store.
I have faced this too ,3 months ago , you just need to open the case and then remove the unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
---------- Post added at 04:27 AM ---------- Previous post was at 04:26 AM ----------
I have faced this too ,3 months ago , you just need to open the case and then unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
Deep flash cable
Try flashing after removing the battery like Aditya said it worked on my friends phone.
[email protected] said:
I have faced this too ,3 months ago , you just need to open the case and then remove the unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
Click to expand...
Click to collapse
Thx man, will try when I get back from work
balazs312 said:
Deep flash cable
Click to expand...
Click to collapse
It's already in EDL 9008 mode, I used the test point. Don't know if the DFC will do anything different, but will try it anyway if the way Aditya told me don't work
I should explain you fully
1)removing battery will keep the phone in edl mode but it will solve your error of mi flash is mi flash will successfully flash the fastboot ROM ,remember you need to first remove the battery cable then insert phone ,no light will blink but it will be recognized as qsp loader port in your PC ,don't worry
2) after successfully completing the first step flash the complete fastboot ROM ,it should go success
3)now don't replug the battery cable now ,do nothing ,just insert cherger and press power button as long as the screen don't turn on ,when it will turn on the battery bar wouldn't go up, then without removing the charger cable from phone ,insert battery, you will see that battery is still not charging, nothing to worry this was just to turn the display on ,now again press the power button for 10 to 14 sec so that the device reboot and boom your phone will start charging and after you can successfully boot into system and use your phone.
4)this is if you still cannot successfully flash using mi flash tool just unplug all a the cable which you see after opening back case don't worry you just have to open the cables which you see ,you don't have to unplug those cables in which you have to open screws etc .
Hope this will help you
[email protected] said:
I should explain you fully
1)removing battery will keep the phone in edl mode but it will solve your error of mi flash is mi flash will successfully flash the fastboot ROM ,remember you need to first remove the battery cable then insert phone ,no light will blink but it will be recognized as qsp loader port in your PC ,don't worry
2) after successfully completing the first step flash the complete fastboot ROM ,it should go success
3)now don't replug the battery cable now ,do nothing ,just insert cherger and press power button as long as the screen don't turn on ,when it will turn on the battery bar wouldn't go up, then without removing the charger cable from phone ,insert battery, you will see that battery is still not charging, nothing to worry this was just to turn the display on ,now again press the power button for 10 to 14 sec so that the device reboot and boom your phone will start charging and after you can successfully boot into system and use your phone.
4)this is if you still cannot successfully flash using mi flash tool just unplug all a the cable which you see after opening back case don't worry you just have to open the cables which you see ,you don't have to unplug those cables in which you have to open screws etc .
Hope this will help you
Click to expand...
Click to collapse
Hey man, didn't work, I disconnected the battery as you said and still got the error when I tried to flash. I downloaded the last rom available from xiaomi site (kenzo_global_images_V9.5.3.0.MHOMIFA_20180405.0000.00_6.0_global_7b6353b764), but still nothing.
I guess it's the EMMC chip alright ;x, but thx anyway
Bro sorry that I couldn't help but can you please try unpluging the cable as shown in the figure and then try to flash using mi flash tool if it still even don't help sorry bro
Unplug the cable given in figure and then try to flash using mi flash , if the device is not detected then replug that cable and and then try to flash if it still don't help sorry bro
[email protected] said:
Bro sorry that I couldn't help but can you please try unpluging the cable as shown in the figure and then try to flash using mi flash tool if it still even don't help sorry bro
Unplug the cable given in figure and then try to flash using mi flash , if the device is not detected then replug that cable and and then try to flash if it still don't help sorry bro
Click to expand...
Click to collapse
Already tried, didn't work, but thx anyways man
Just plug it in to a wall charger. I had the same issue even after edl flash miui rom but charging it fixed my problem. Follow these steps.
1- plug it in
2- ignore the red led blinking
3- wait for 5 min.
4- it will boot.
5- if doesn't, I'm sorry
I was trying to install a modified ROM in redmi note 3. The rom had a modified emmc_appsboot.mbn and a modded recovery.img. I entered in sp flash tool and was flashing the rom and the app crashed or battery ran out while installing. Now the fastboot and the os were bricked. At this point when I tried to boot the MI logo was showing up for a second and then it reboots. At this point, it was showing up as a fastboot device on my pc so I tried using command fastboot reboot edl and it worked (in the black screen). now in edl mode (red light blinking when plugged in), I tried installing stock rom and again it was interrupted ( due to maybe battery issue). Now when I connect the device to pc it detects as 900e instead of 9008, whenever I press the power button it blinks red light like in edl mode ( this may also happen if the battery has no juice), I cannot charge coz its still in edl mode.
I tried Deep Flash cable, it didn't work. I then manually updated the driver from 900e to 9008, it shows up in mi flash tool but installation fails with the error cannot receive hello package.
After ****ing my device this much I went to a mi service center and they said that when they try to install software, it fails. They dunno why, I guess the battery is not enough to install the software.
Finally, They asked to replace the motherboard. since spending 5k on kenzo in october 2018 is a waste any bright minds have any idea for repair,?
ISH99 said:
I was trying to install a modified ROM in redmi note 3. The rom had a modified emmc_appsboot.mbn and a modded recovery.img. I entered in sp flash tool and was flashing the rom and the app crashed or battery ran out while installing. Now the fastboot and the os were bricked. At this point when I tried to boot the MI logo was showing up for a second and then it reboots. At this point, it was showing up as a fastboot device on my pc so I tried using command fastboot reboot edl and it worked (in the black screen). now in edl mode (red light blinking when plugged in), I tried installing stock rom and again it was interrupted ( due to maybe battery issue). Now when I connect the device to pc it detects as 900e instead of 9008, whenever I press the power button it blinks red light like in edl mode ( this may also happen if the battery has no juice), I cannot charge coz its still in edl mode.
I tried Deep Flash cable, it didn't work. I then manually updated the driver from 900e to 9008, it shows up in mi flash tool but installation fails with the error cannot receive hello package.
After ****ing my device this much I went to a mi service center and they said that when they try to install software, it fails. They dunno why, I guess the battery is not enough to install the software.
Finally, They asked to replace the motherboard. since spending 5k on kenzo in october 2018 is a waste any bright minds have any idea for repair,?
Click to expand...
Click to collapse
Remove the battery . fully charge it and put it back and do ur experiment.
first charge your phone properly and have a look your phone is in which state.
Hello Members,
The device was stuck in boot loop so i tried to flash via EDL mode. First it came to edl mode but while flashing i got some XML error. Now i tried to put the phone again in EDL mode but its not working.
I had removed the battery and and i have connected to 2 jumper pins 1 and 4 and connect the usb but the phone dont seems to come to edl mode. just flashes the MI screen and power off repeatedly.
Now i connect the phone directly with battery on and its coming as charging but surprisingly the phone got detected, the device manager shows the phone as Linux file stor gaget usb device. I tried to flash with mi flash tool and its running indefinitely saying flashing..
Help...