good morning everyone
it has suffered a fall, it worked normal, it was downloaded, I put it to load, when wanting to turn on, it got stuck in the logo, it tries to start and it restarts, it lets flash with flastoll but it does not start, with pc companation it recognizes it , but can not repair it, indicates some type of error when wanting to repair it., some solution.
download newflasher and try reflashing the firmware.
sinkoo1979 said:
download newflasher and try reflashing the firmware.
Click to expand...
Click to collapse
Ufs info: SAMSUNG,KLUCG4J1ED-B0C1,0200
Emmc info: FAILEmmc-info not supported,
Try flashing with newflasher, and this is the error, it's all stuck in the logo.
do you have flash drivers installed?
Related
So I tried flashing to ICS, but halfway through flashtools gives me an error and just kicks my phone out.
I disconnect the phone and now it's stuck in a bootloop - PCC can't detect it, but flashtools can just for a few seconds, but it's not long enough to re-flash to a stock firmware.. what do I do!
NguyenT said:
So I tried flashing to ICS, but halfway through flashtools gives me an error and just kicks my phone out.
I disconnect the phone and now it's stuck in a bootloop - PCC can't detect it, but flashtools can just for a few seconds, but it's not long enough to re-flash to a stock firmware.. what do I do!
Click to expand...
Click to collapse
Try boot to flash mode and flash stock firmware.
Are you unlocked?
Hello,
I have a S3 which is stuck in a bootloop at the samsung logo.
when i turn it on it shows the logo for some seconds then the screen goes black and the logo re-appears.
i can not boot into recovery mode, but download mode is working without a problem every time.
i tried flashing stock firmwares with odin and also tried kies emergency firmware recovery. the flashing always went without any problem, but it had effect. whatever i try, i am never able to boot into recovery and still stuck in the bootloop.
in some tries after flashing the screen just shows the samsung logo forever, but after rebooting it once it then is stuck in a bootloop again (shows the logo - screen goes black - shows the logo...)
i also tried flashing TWRP and CWM via odin, but again i can never boot into recovery mode.
what should i try next?
thx alot for any helpful comment
Varjo said:
Hello,
I have a S3 which is stuck in a bootloop at the samsung logo.
when i turn it on it shows the logo for some seconds then the screen goes black and the logo re-appears.
i can not boot into recovery mode, but download mode is working without a problem every time.
i tried flashing stock firmwares with odin and also tried kies emergency firmware recovery. the flashing always went without any problem, but it had effect. whatever i try, i am never able to boot into recovery and still stuck in the bootloop.
in some tries after flashing the screen just shows the samsung logo forever, but after rebooting it once it then is stuck in a bootloop again (shows the logo - screen goes black - shows the logo...)
i also tried flashing TWRP and CWM via odin, but again i can never boot into recovery mode.
what should i try next?
thx alot for any helpful comment
Click to expand...
Click to collapse
You can Try this:
1.) Pull out battery
2.) Put it in again
3.) Press Vol up + home + power
4.) When the Samsung Logo appears let it off
I think you press the Buttons too long.
I had the same problem!
S1ay3r666 said:
I think you press the Buttons too long.
Click to expand...
Click to collapse
i really tried everything, it's not working. btw with i am stuck at the very first image, where it says "samsung Galaxy sII GT-I9300".
i dont think it's just the way i press the buttons because i can reach it on my s1 and s2 without a problem, it's just not working on this device.
could some setting like "nand erase all" in odin help? in other threads there is sometimes mentioned that the internal file system might be screwed up and in those cases a simple odin reflash does not help anymore...
Nand erase will usually hard brick it. Try the rescue firmware from general forum, sticky thread. Follow the guide exactly as it includes a pit file.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
Try the rescue firmware from general forum, sticky thread. Follow the guide exactly as it includes a pit file.
Click to expand...
Click to collapse
thx, but i already did that (multiple times) and flashing via odin always succeeds. then the phone reboots and is stuck at the first samsung galaxy s.. screen. twice i managed somehow to get into recovery (after flashing cwm6) but it then randomly rebooted.
and i dont think that the power button is stuck because when i am in download mode it is perfectly fine it never reboots itself unexpectedly.
Had a similar issue on my tab2 p3100. It all happened when I tried flashing a custom recovery from rom manager.
A bad flash of anything related to recovery or bootloader could be a probable cause.
I remember a knowledge share on one of the threads describing this issue and as mentioned on it all I had to do is this:
1) switch off the device and plug in the charger. This would light up the display showing you the charging status. The status has to show if at least your bootloader part of the phone is fine.
2) plug out the charger and immediately press the three buttons (home + vol up + power) get into recovery mode. This step has to work and help you get to recovery mode.
***Note : the interval within which this step has to be performed is too short since the display would turn off immediately as soon as you plug out the charger. A bit tricky too so you have to be fast. If this misses getting you into recovery, pull out the battery and put it back again. Repeat step1 and 2 again.
3) upon successfully getting into recovery, perform wipe data, cache and select reboot phone from option available on recovery again.
Allow the device to boot. This could take a while since you have performed a data wipe and may prompt for first time set up.
I was able to restore functionality on my tab after these steps and like ppl learn from their mistakes, I then learnt that recoveries and bootloaders are things that needs to be done with a pc only.
Worth a try if you have tried other alternatives and found no go. may help. Who knows..
all the best.
thats also not working. i tried to get into recovery since two days now...
i also tried the steps from this thread: http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
but again, after i flash the cf-root (successfully) the phone does neither boot into recovery by itself nor can i do it by hand...
its crazy... in download mode i can see the model number (GT-I9300) and i thought as long as the model number is there and i can enter download mode there should be a way to recover the device.
but i cannot think of anything to try that i have not done yet
If the rescue firmware didn't help then it looks like the emmc chip is damaged.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
If the rescue firmware didn't help then it looks like the emmc chip is damaged.
Click to expand...
Click to collapse
is there a way to make certain of this? how can i tell if it is really a hardware damage and not just a software brick?
i just dont want to let the phone go, it looks still so shiny
is there anything else that could cause the phone not booting into recovery mode after flashing custom recoveries?
Varjo said:
is there a way to make certain of this? how can i tell if it is really a hardware damage and not just a software brick?
i just dont want to let the phone go, it looks still so shiny
is there anything else that could cause the phone not booting into recovery mode after flashing custom recoveries?
Click to expand...
Click to collapse
http://forum.xda-developers.com/gala...-help-t2737707
Same here, still didn't found how to fix it.. I guess our motherboard just died..
Howewer I have a solution that "almost" worked for me.
Get a stock firmware in odin and turn on Nand erase and T-flash
When it's done phone reboots and you'll see just "Downloading..." mode when you turn it on.
Then got to Kies and Select firmware recovery...
Enter s/n and model name and wait for the flash to complete.
With it , I got past boot logo and actually booted into android but the phone crashed because I guess I have a memory issue..
Well , gl. If you don't find anything else helpful , try going with this method..
Hi guys, I believe my phone is bricked/stuck in bootloop and I need your help. I was trying to flash this ROM and just before I started to install, after I did a full wipe, the phone hanged, I did a soft-reset and my Sola got stuck in bootloop. I tried flashing .54 FTF stock ICS ROM, but Flashtool keeps giving me an error and aborts the flash. (also, after less than a minute, the phone will go out of flash mode and get stuck on Sony logo)
Is there another way I can flash back a stock ROM and unbrick my phone? Thanks in advance for the help, I hope you can help me out, I'm a total noob, it's the first time I tried to flash a custom ROM
EDIT: BTW, I hard reset the phone several times in attempt to turn it off and boot in flash mode, since the phone will not shut down.
2nd EDIT: I can't get into recovery either.
3rd EDIT: SOLVED using the x86 version of flashtool instead of the x64.
Today morning i tried to update MCU with kld5 v2.97. Previously i had kld6 v2.91.
Afte that unit never booted again. All i get is a quick flash of malaysk boot logo for one second and then black screen with devices button lighting from blue to pink all the time.
I tried to flash firmware again with rkbatch tool and after finishing with success the same problem again.
Is there any way to flash old MCU again? Is there any tool to flash MCU from pc?
Billkaza said:
Today morning i tried to update MCU with kld5 v2.97. Previously i had kld6 v2.91.
Afte that unit never booted again. All i get is a quick flash of malaysk boot logo for one second and then black screen with devices button lighting from blue to pink all the time.
I tried to flash firmware again with rkbatch tool and after finishing with success the same problem again.
Is there any way to flash old MCU again? Is there any tool to flash MCU from pc?
Click to expand...
Click to collapse
try to flash MCU kld6 v2.91 from recovery
but i cant get into recovery
Billkaza said:
but i cant get into recovery
Click to expand...
Click to collapse
it's an img file so you could flash it in same way of firmware
Billkaza said:
I tried to flash firmware again with rkbatch tool and after finishing with success the same problem again.
Click to expand...
Click to collapse
rockchp batch tool doesnt leave me is there any other tool i could try?
I get loading firmware failed error.
sorry I cant help you more...
Case closed
Really dont know how but after several firmware flashes it came to life again.
Holding down reset whilst pressing power, releasing rest then releasing power does not work ? Do you ahve a power button ?
I have a power i tried booting to recovery but this didnt seem to fix my problem. Anyway as it is fixed i will never now what went wrong
Thanks guys for help
Billkaza said:
Today morning i tried to update MCU with kld5 v2.97. Previously i had kld6 v2.91.
Afte that unit never booted again. All i get is a quick flash of malaysk boot logo for one second and then black screen with devices button lighting from blue to pink all the time.
I tried to flash firmware again with rkbatch tool and after finishing with success the same problem again.
Is there any way to flash old MCU again? Is there any tool to flash MCU from pc?
Click to expand...
Click to collapse
Could you post your steps getting your computer to read the radio without recovery. Thanks!!
I'm very happy that your unit works again.
Just un-bricked my device with these steps!
http://forum.xda-developers.com/and...d-kgl-unit-t3457538/post68656680#post68656680
I followed this guide:
https://forum.xda-developers.com/xperia-xa/how-to/f31xx-how-to-root-xperia-xa-noob-t3430170
With some specific files (boot and recovery images) from here:
https://forum.xda-developers.com/xa-ultra/how-to/how-to-root-xperia-xa-ultra-dual-t3439173
The rough steps that I took:
Put the UPDATE-SuperSU-v2.76-20160630161323.zip in the microsd
Unlocked the bootloader
"fastboot flash boot boot.img" and "fastboot flash recovery recovery.img"
Booted into TWRP
Since the internal data was shown as (0) , I Wiped the device.
Installed SuperSU-v2.76 from the microsd
Rebooted the device
It did an automatic reboot after going through the logos (I guess this part is expected after installing SuperSU)
After that, it gets stuck on the Xperia logo (the video logo keeps playing)
Now, after I turn on the device:
It goes through the Sony logo
It goes through the Android logo
It gets stuck on the Xperia logo (while playing the logo)
It doesn't get passed the Xperia logo.
Things I can still do:
I can boot into TWRP recovery (yay?)
I can use adb sideload with TWRP
I can't yet get back into fastbood mode, but I guess I can if I keep at it. I could go to fastbood mode before, but for some reason I can't anymore. I think it has to do with drivers. By default it recognizes the device as "SEMC flash drive" and will not recognize it as fastboot. After about a minute or so, it will disconnect the "SEMC flash drive" and boots the phone.
Give it to me straight, is my phone actually bricked?
If not, please let me know what I can do to fix it. It is very much appreciated to hear from anyone about this. Thank you all in advance.
If you need any additional info (logs, phone details, etc. etc.) feel free to ask me and I will happily comply.
If you can't get through the bootanimation, then yes that's kind of a soft brick. A solution would be to flash an official firmware from xperifirm (preferably .100 or .111 in order to to install root successfully) and then get everything done with simple baby steps. After flashing, you can wipe your data (if you wanna), reboot and then install root (I do not recommend flashing supersu and wiping at the same time when using an official firmware).
Note: Because we are stuck with only official fws, boot and recovery files can only work on specific fws
sexxualization said:
If you can't get through the bootanimation, then yes that's kind of a soft brick. A solution would be to flash an official firmware from xperifirm (preferably .100 or .111 in order to to install root successfully) and then get everything done with simple baby steps. After flashing, you can wipe your data (if you wanna), reboot and then install root (I do not recommend flashing supersu and wiping at the same time when using an official firmware).
Note: Because we are stuck with only official fws, boot and recovery files can only work on specific fws
Click to expand...
Click to collapse
Hey
Thanks for your reply on my cry for help.
So basically get the firmware from Xpeifirm, make sure boot is working fine (basically back to square one ... sorta), then root by installing the SuperSU again. right?
I had already looked at Xperifirm before this. but I couldn't figure out how to properly use it. and now I'm a bit stuck.
I followed these:
https://forum.xda-developers.com/cr...xperifirm-xperia-firmware-downloader-t2834142
https://www.youtube.com/watch?v=X_Y-BOWlQdw
But when I follow the steps, I get stuck here (when creating the bundle using the bundler in flash tools) :
http://imgur.com/a/wl3Cc
Any ideas on how to proceed?
Also another question. Can I get away with using adb sideloader instead of flashtool? some driver problems that are bugging me ...
Appreciate your response and thank you so much!
sony- android- xperia- off
good day! i hope im on the correct thread. i am having this issue on my xperia xa ultra dual.
everytime i turn the device on, it displays the sony logo, then the android logo, the xperia logo, then it turns off. i cant seem to get past through this regardless if i'll press the volume- and power or the volume+ and power. im almost certain that this can be fixed by doing something on the flashtool. i guess i just dont know how to do it. a step-by-step tutorial is greatly appreciated.
Can you get it into fash mode? If you can just flash ftf file for your phone.
Sent from my F3213 using xda premium
mchlbenner said:
Can you get it into fash mode? If you can just flash ftf file for your phone.
Sent from my F3213 using xda premium
Click to expand...
Click to collapse
hi. thanks for the response! i tried to flash the stock ftf for my f3212 and now it doesn't boot at all! T___T it will only show a steady red light if its connected to the PC.
Unfortunately this is a known issue when flashing after only red light when plug in for charging.
If you are under warranty send in for service their no known fix for this.
It happened to me I junk it.
And got another one.
Sent from my F3213 using xda premium