Section 1 Covers how to install pie on H87320i.
Section 2 Covers How to rollback from H87329a to H87320I
Section 1
Download FOTA file
v29a
https://drive.google.com/file/d/1BNI2Cvuk1eX4ocx2S6_YnbqNUARgIbts/view
v30b
https://mega.nz/#!e9cQ0QTZ!vpCXt1eYUUpTo2NJ-0t8I6SiIxt6qXbTOjupsHIzB9s
LG UP
https://www.mylgphones.com/download-lg-up-software (use 1.116 non pacteched lab version)
Uppercut
https://forum.xda-developers.com/lg-g5/development/uppercut-lgup-loader-g5-variants-t3511295
Extract .zip file of LG UP
Conect phone to pc (MTP) and enable usb debugging (if don't know how search in internet)
Install LG UP after installation
Extract Upper Cut don't forget to turn off your antivirus before you extract
Run Uppercut.exe. LG UP will run
Now in you will see some buttons select FOTA
A little bit lower you will see File Path and under it you will see probably an .up file, press on it after that press on 3 dots that just apear and find Update file you download (.up)
Before pressing start unlock your phone and stay with display turned on
Now, the last press start, after like 30s-1m on display should apear FOTA Upgrade and after should turn off and start upgrading.
At the end it will bootloop like a minute, it is normal, after that it will start and finish the update
Congrats! You got the Pie?
NOTE:
LG G6 USB drivers must b installed
If you have Lg bridge Install, it might interfere while flashing using Lg UP
Section 2
How to roll back from pie
check post below
https://forum.xda-developers.com/showpost.php?p=80464669&postcount=46
Credits:
f.h7 for rollback tutorial
v30b link by umaga2012
Some tutorial points by vaniok56 (Reddit)
harib12 said:
Download FOTA file
https://drive.google.com/file/d/1BNI2Cvuk1eX4ocx2S6_YnbqNUARgIbts/view
LG UP
https://www.mylgphones.com/download-lg-up-software (use 1.116 non pacteched lab version)
Uppercut
https://forum.xda-developers.com/lg-g5/development/uppercut-lgup-loader-g5-variants-t3511295
Extract .zip file of LG UP
Conect phone to pc (MTP) and enable usb debugging (if don't know how search in internet)
Install LG UP after installation
Extract Upper Cut don't forget to turn off your antivirus before you extract
Run Uppercut.exe. LG UP will run
Now in you will see some buttons select FOTA
A little bit lower you will see File Path and under it you will see probably an .up file, press on it after that press on 3 dots that just apear and find Update file you download (.up)
Before pressing start unlock your phone and stay with display turned on
Now, the last press start, after like 30s-1m on display should apear FOTA Upgrade and after should turn off and start upgrading.
At the end it will bootloop like a minute, it is normal, after that it will start and finish the update
Congrats! You got the Pie?
NOTE:
LG G6 USB drivers must b installed
If you have Lg bridge Install, it might interfere while flashing using Lg UP
Some tutorial points by vaniok56 (Reddit)
Click to expand...
Click to collapse
Thanks for the tutorial...will this still keep all settings etc from oreo?
Matt
it took a lot longer than 1mn to finish that bootloop thing, you gave me a scare LMAO
after like 10mn or so the phone is up and running
thanks
matthew33 said:
Thanks for the tutorial...will this still keep all settings etc from oreo?
Matt
Click to expand...
Click to collapse
yes
KyleKlarkson said:
it took a lot longer than 1mn to finish that bootloop thing, you gave me a scare LMAO
after like 10mn or so the phone is up and running
thanks
Click to expand...
Click to collapse
Good for u
I keep getting an error saying mtp service not running after clicking the start button to initiate the upgrade.
Leonidas87 said:
I keep getting an error saying mtp service not running after clicking the start button to initiate the upgrade.
Click to expand...
Click to collapse
Here you go:
https://www.youtube.com/watch?v=OaCdtRz8k-g
Matt
I have already tried to upgrade this beta version a few times, however, I always have an SPC error at the beginning of the process (c.a. 4%). I searched around xda and found out that this error is attributed to "a wrong version" - but this should be impossible as I am using H873.
Leonidas87 said:
I keep getting an error saying mtp service not running after clicking the start button to initiate the upgrade.
Click to expand...
Click to collapse
Mostly Occurs when you have LG Bridge. I also got that error uninstalling LG bridge resolved it.
DVD-XDA said:
I have already tried to upgrade this beta version a few times, however, I always have an SPC error at the beginning of the process (c.a. 4%). I searched around xda and found out that this error is attributed to "a wrong version" - but this should be impossible as I am using H873.
Click to expand...
Click to collapse
You should be using H87320i in order to update. Please make sure you have correct drivers and you are using LGUP version I provided. In order to update your phone should be on the home screen and sometime Lg bridge also cause trouble
I have H871 that has been converted to H873 by installing the Canadian Oreo ROM. Is it possible for me to upgrade to pie using this tutorial?
I've never installed lg bridge.
I'm wondering if it only works with specific carriers. If I click firmware update the phone reboots and trying to do a firmware update just to see.
No matter what I get the mtp error when trying install this firmware.
I'm in Canada
H7320i software version.
Is it possible to install on h87320c?
I am using H87320i, flashed using LGUP+Uppercut few months ago. I uninstalled LG bridge and tried to use new version of LGUP + a newer LGUP_common.dll, however, always have an error : 0x2000 open port error.
This seems to be related to the LGUP_common.dll, but I already tried to use few different files (versions) downloaded from different sources, the error is still there. (Note that driver is working fine as I can access my phone using PC/laptop).
@harib12: can you please upload the dll file you used?
umaga2012 said:
I have H871 that has been converted to H873 by installing the Canadian Oreo ROM. Is it possible for me to upgrade to pie using this tutorial?
Click to expand...
Click to collapse
If you are already using H873 stock rom then it should be fine however, I will not take responsibility for your action. Compatibility mainly depends on hardware similarity.
DVD-XDA said:
I am using H87320i, flashed using LGUP+Uppercut few months ago. I uninstalled LG bridge and tried to use new version of LGUP + a newer LGUP_common.dll, however, always have an error : 0x2000 open port error.
This seems to be related to the LGUP_common.dll, but I already tried to use few different files (versions) downloaded from different sources, the error is still there. (Note that driver is working fine as I can access my phone using PC/laptop).
@harib12: can you please upload the dll file you used?
Click to expand...
Click to collapse
I am not using any common dll
LeeTG3 said:
Is it possible to install on h87320c?
Click to expand...
Click to collapse
It should be didn't try but it is FOTA. An OTA requires a sequence. However, as you are pushing this using LG UP maybe you have some luck. But I suggest flashing H8732oi KDZ.
Leonidas87 said:
I've never installed lg bridge.
I'm wondering if it only works with specific carriers. If I click firmware update the phone reboots and trying to do a firmware update just to see.
No matter what I get the mtp error when trying install this firmware.
I'm in Canada
H7320i software version.
Click to expand...
Click to collapse
If You're following this tutorial your phone should show a FOTA screen then it should boot. It is an open FOTA and not restricted to carriers. and are you using the links i have given? do you install any Common dll?. If yes remove the common dll as your using upper cut.
I use this tutorial and LG UP tell me a message that have a problem with dll.
Can you help me.
Enviado desde mi LG-H870 mediante Tapatalk
yoyodiaz said:
I use this tutorial and LG UP tell me a message that have a problem with dll.
Can you help me.
Enviado desde mi LG-H870 mediante Tapatalk
Click to expand...
Click to collapse
You didn't replace the model folder and LGUP in C drive properly. Don't use the folder you downloaded to start the program.
Related
I own a LG-P765
I used LG's software updater and it decided to put on a useless Chinese version of android 4.0.4 with no play store
Need help putting it back
I tried hard resetting and it didnt help
I tried flashing with KDZ but the program kept on crashing
Need help BADLY!!!!!!!!!!
manniefabian said:
I own a LG-P768
I used LG's software updater and it decided to put on a useless Chinese version of android 4.0.4 with no play store
Need help putting it back
I tried hard resetting and it didnt help
I tried flashing with KDZ but the program kept on crashing
Need help BADLY!!!!!!!!!!
Click to expand...
Click to collapse
Try to recovery your phone by LG mobile support tool
1. Download LG mobile support tools from LG web site. http://www.lg.com/us/support-mobile/lg-P769
2. Boot your phone to SW upload mode
3. Start LG mobile support tool.
4. Connect your phone with usb cable. LG mobile support should detect your phone model. If not please reinstall LG usb drivers.
5. In LG mobile support tools, select "Customer support" > "Recover phone"
4. New dialog popup ask for IMEI or S/N. Your IMEI should already fill in textbox just click first button.
5. Wait for LG flash program to load kdz from their server and flash your phone. It should work.
Just put on the Chinese android!!!
All that did was put on the chinese android i need a way to flash it
manniefabian said:
I tried flashing with KDZ but the program kept on crashing
Click to expand...
Click to collapse
What do you mean "crashing"? What excatly happens?
Once i enter in the correct KDZ file i press start it says unpacking then the prgaram stops working
I have tried this on other computers also
If u can give me a step by step version on how to use the KDZ updater program that would help
My phone is the LG P765 or P760 running Android 4.0.4
anirion said:
What do you mean "crashing"? What excatly happens?
Click to expand...
Click to collapse
manniefabian said:
Once i enter in the correct KDZ file i press start it says unpacking then the prgaram stops working
I have tried this on other computers also
If u can give me a step by step version on how to use the KDZ updater program that would help
My phone is the LG P765 or P760 running Android 4.0.4
Click to expand...
Click to collapse
Step by step you find here: http://forum.xda-developers.com/showthread.php?p=36351786
You can also try to download again KDZ file, maybe file which you try to use is corrupted.
anirion said:
Step by step you find here: http://forum.xda-developers.com/showthread.php?p=36351786
You can also try to download again KDZ file, maybe file which you try to use is corrupted.
Click to expand...
Click to collapse
Thanks im gonna try it if it doesn't work is there any other way?
I was wondering how to this.
I was flashing Killjoy's performance scripts (see http://forum.xda-developers.com/showthread.php?t=2411161). After flashing the file and choosing to reboot, for dumb reasons I chose to disable recovery flash when it asked to reboot. Now, when I go to LG setup, once I'm done, I get the message that "lg setup wizard has stopper working" and loops me back to the start of the setup. Please help!:crying:
I know L9 is virtually unbrickable. I just need to be pointed in the right direction and I know I can bring it back!
Edit: Issue resolved!
Did you by any chance uninstall it using titanium backup or similar? Try to get a logcat.
Sent from my LG-P760 using xda app-developers app
I guess he can't use none of the applications as he is stuck in the wizard. Try reflasing a stock ROM using kdz: http://forum.xda-developers.com/showthread.php?t=2085344
SkarlosBME said:
I guess he can't use none of the applications as he is stuck in the wizard. Try reflasing a stock ROM using kdz: http://forum.xda-developers.com/showthread.php?t=2085344
Click to expand...
Click to collapse
Yea, this is the case. Can't get out of it. I really don't know how in the world did it uninstall itself. I didn't use Titanium Backup at all. After flashing the killjoy zip file, I chose to reboot. I then got a warning:
"ROM may flash stock recovery on boot. Fix? THIS CAN'T BE UNDONE" I then get 3 options to chose from: "No", "Yes - Disable recovery flash, "++Go Back++
I chose yes, and then all went haywire. Is there a way I can determine my phone's connection type via computer? I tried flashing V20D using the KDZ offline method, but it won't progress. It says "Phone not connected." Last I recall, I left the connection on media sync (MTP, I think it's its acronym). Since I'm on JB, I know it needs to be in LG Software Mode.
I have faced this issue too, even if I entered into SW Upgrade mode manually, KDZ did not detect my phone :/
However, I had success using the official LG updater software (connected my phone in SW upgrade mode).
SkarlosBME said:
I have faced this issue too, even if I entered into SW Upgrade mode manually, KDZ did not detect my phone :/
However, I had success using the official LG updater software (connected my phone in SW upgrade mode).
Click to expand...
Click to collapse
Was your phone recognized by your computer? Because mine isn't. Think you can tell me more or less the steps you took to make it work?
Here's what I've tried so far:
1. downloaded most updated LG drivers
2. downloaded official LG mobile support tool
3. ran it, no effect.
4. downloaded LG pc suite, based on troubleshooting.
5. tried lg mobile support tool again, no good. Said connect PC to internet (???)
6. tried LG mobile support tool from shtttps from offline flash method, no good.
7. Put phone on SW upgrade mode (removed battery, volume up, put battery back in) and retried offline flash method again, halts at 15%. Says that phone isn't connected. It was set on DIAG since it's JB software.
8. Tried recovery update, but phone isn't recognized even if I put IMEI number in.
Thanks!
Flash a ics kdz... should work..
Sent from my LG-P769 using XDA Premium HD app
jbonilla51 said:
...
5. tried lg mobile support tool again, no good. Said connect PC to internet (???)
...
Click to expand...
Click to collapse
You have forgot to remove the lines you added at the end of your hosts file. Remove them, reboot your PC and then try again with the official tool.
SkarlosBME said:
You have forgot to remove the lines you added at the end of your hosts file. Remove them, reboot your PC and then try again with the official tool.
Click to expand...
Click to collapse
I forgot about that! Tried it, and the official tool worked excellent! Phone was able to go through setup wizard without a problem! Thanks a lot, man! Hitting the thanks button now!
:good::good::good:
SkarlosBME said:
You have forgot to remove the lines you added at the end of your hosts file. Remove them, reboot your PC and then try again with the official tool.
Click to expand...
Click to collapse
could you please elaborate on this. hosts files on Windows? I'm having similar problem with new lg k7 no kdz and for some reason this phone has no recovery at all. button combo will perform a factory reset with no prompt butt no menu options at all. and phone getting no dev love at all. it's very touchy. like it'll brick if you look at it the wrong way
How to put into download mode
1st thing download the zip in the linkhttp://d-h.st/6Wp
Install:
1. Install the LG drivers.
2. Install LGFlashTools v1.8 (but don't run it)
3. Extract the TOT file from the ZIP
When LG Flash Tool is installed, do not launch it.
7) Copy MegaLock.dll to C:\LG\LGFlashTool, This is a hidden folder so enable "hidden folders". Replace the old MegaLock.dll file if you have already installed LG Flash Tool on your computer.
8) Launch LG Flash Tool.
You might see a window with Korean language, just click on OK.
Check the Select Manual Mode on the top.
9) MAKE SURE UNDER, DEVICE MANAGER, YOUR PORT IS SET TO COM 41 FOR YOUR DEVICE.
10) Click the DLL box and choose the dll file from above for you phone model.
11) Click the S/W box and select the firmware file with .tot extension.
12) Now click the Yellow arrow button on the top left of the main window.
The firmware installation will be triggered.
Ignore if you see any temporary error and just wait patiently till it is finished.
Do not close the Flash Tool window.
13) Power off and place on dock when lg screen comes on swipe from button left to top right
Your LG G Watch will restart showing firmware installation progress in percent (%).
When all is done
I will post more videos and pics later
Nice job D -Fuse.........
Sent from my: T- Mobile LG G3
this is huge!!
ptesmoke said:
this is huge!!
Click to expand...
Click to collapse
Working with my buddy on recovery too. 1st built bricked tho lol
D-FUSE said:
Working with my buddy on recovery too. 1st built bricked tho lol
Click to expand...
Click to collapse
soft brick I would assume...lgflashtool should save damn near most bricks...
ptesmoke said:
soft brick I would assume...lgflashtool should save damn near most bricks...
Click to expand...
Click to collapse
Yeah just lg screen I just fastbooted the stock recovery to fix it. Btw if you do soft brick hit the reset button to power off and throw on the dock real quick and swipe
D-FUSE said:
Yeah just lg screen I just fastbooted the stock recovery to fix it. Btw if you do soft brick hit the reset button to power off and throw on the dock real quick and swipe
Click to expand...
Click to collapse
Love the swipe nice find
So where are the LG drivers..Last night I was all over that site since my pc wouldnt install drivers properly for the watch and the only thing tI found available to download is the documentation...
Also, running the LG tool thingy...threw up flags in Norton and it quarantined the file lol
Tower1972 said:
So where are the LG drivers..Last night I was all over that site since my pc wouldnt install drivers properly for the watch and the only thing tI found available to download is the documentation...
Also, running the LG tool thingy...threw up flags in Norton and it quarantined the file lol
Click to expand...
Click to collapse
http://oceanhost.eu/uvriaayam4sz/LGUnitedMobileDriver_S4981MAN38AP22_ML_WHQL_Ver_3.8.1.exe.html
You can find lg drivers there and turn off antivirus the tool isn't a virus you'll be
D-FUSE said:
http://oceanhost.eu/uvriaayam4sz/LGUnitedMobileDriver_S4981MAN38AP22_ML_WHQL_Ver_3.8.1.exe.html
You can find lg drivers there and turn off antivirus the tool isn't a virus you'll be
Click to expand...
Click to collapse
Oh I know..just wanted to toss that there and let ya know..thanks for the link.. The LG site is basically useless for the watch
Tower1972 said:
Oh I know..just wanted to toss that there and let ya know..thanks for the link.. The LG site is basically useless for the watch
Click to expand...
Click to collapse
Lg site is useless for everything ?
deleted for now..trying something
Thanks for posting this! My device was among those that had a messed up partition table and this seems to have solved it!
Hi,
after installing lg drivers, no com41 found on my pc.
only "lg mobile composite usb device"
what is the right driver?
edit: changed manually to "LGE Android Plattform USB Modem"
edit: confirm working with "LGE Android Plattform USB Serial Port (Com41)" and "LGE Android Plattform USB Modem" on Com5
regards
starbase64
starbase64 said:
Hi,
after installing lg drivers, no com41 found on my pc.
only "lg mobile composite usb device"
what is the right driver?
edit: changed manually to "LGE Android Plattform USB Modem"
edit: confirm working with "LGE Android Plattform USB Serial Port (Com41)" and "LGE Android Plattform USB Modem" on Com5
regards
starbase64
Click to expand...
Click to collapse
You have to change it in device manager on the lg modem in Advanced tab
yes, i post a Screenshot later today.
starbase64 said:
yes, i post a Screenshot later today.
Click to expand...
Click to collapse
Sorry my data is being throttled right now and I can't see the pic
D, Thank you, hopefully you'll be my saviour. But I'm at a bit of a loss... Does anyone happen to have the lg drivers?
And, the instructions in the op skip from step 3 to 7.i feel like im missing something.
Any help would be appreciated as I'm stuck in a perpetual bootloop with no way to enable debugging...
Sparks639 said:
D, Thank you, hopefully you'll be my saviour. But I'm at a bit of a loss... Does anyone happen to have the lg drivers?
And, the instructions in the op skip from step 3 to 7.i feel like im missing something.
Any help would be appreciated as I'm stuck in a perpetual bootloop with no way to enable debugging...
Click to expand...
Click to collapse
https://www.dropbox.com/sh/zuwmht5g5d1lss6/AABA3I3RR_TL2MvUB4uMoVZ8a?dl=0
Should be in my drop box folder
Thank you sir
Hello. Has anybody any idea if its possible to downgrade the g5 from nougat to MM? I really dont like it. Im wondering if it is possible and how? KDZ file for my phone and lgup?
There is automatic update are came in few month just wait some time.
If your variant is H860 go here >> https://forum.xda-developers.com/lg-g5/how-to/guide-downgrade-to-mm-n-t3523999
bluerain28 said:
If your variant is H860 go here >> https://forum.xda-developers.com/lg-g5/how-to/guide-downgrade-to-mm-n-t3523999
Click to expand...
Click to collapse
my variant is h850, but now i got bigger problems...i tried installing a kdz, it failed and now i have no os. i downloaded a lot of kdz but none of them work..help me
same, i downloaded a kdz , rolled back with lg up , that appeared to work., but when my phone comes on and i enter my power up pin its says its incorrect , WTF!!! Tried LGUP to put nougat back on hoping it would help but LG up just crashed every single time i attempt to do anything with phone. Aint got a clue what to do now
You guys try asking autoprime about this?
Sent from my LGE LG-H830 using XDA Labs
dssherwin said:
same, i downloaded a kdz , rolled back with lg up , that appeared to work., but when my phone comes on and i enter my power up pin its says its incorrect , WTF!!! Tried LGUP to put nougat back on hoping it would help but LG up just crashed every single time i attempt to do anything with phone. Aint got a clue what to do now
Click to expand...
Click to collapse
https://forum.xda-developers.com/lg-g5/development/uppercut-lgup-loader-g5-variants-t3511295 donwload uppercut and lgup from here. unzip the uppercut, run it, if it gives you an error that it cant find it in users...roaming bla bla, just copy uppercut in the folder the program wants and it will run fine. then after pluging your device in, open uppercut, select your kdz file and chose upgrade not forbish or fota upgrade or something. i however had the h85020a variant of the firmware. there is 10c and 10e or something. anyway, if u know thats your model just go for it as i said earlier.
Easy update using LG Bridge after backing up. Didn't need backup as update left everything ok (incl. Microsoft launcher). Now V20a-TWN-XX.
Allgood then, but struggling to notice a difference. Maybe a little quicker!
Nope for 870DS Indonesia
Cheers
RooBG said:
Easy update using LG Bridge after backing up. Didn't need backup as update left everything ok (incl. Microsoft launcher). Now V20a-TWN-XX.
Allgood then, but struggling to notice a difference. Maybe a little quicker!
Click to expand...
Click to collapse
Can we flash it on indian DS model?
Sent from my LG-H870DS using Tapatalk
Any others recived oreo ?
Now V20a-HKG-XX.
mohammadstr said:
Any others recived oreo ?
Click to expand...
Click to collapse
My H870DS from TWN (actual software version V10m-TWN-XX) shows no update OTA, but is now downloading a new update in LG Bridge.
ppp10 said:
My H870DS from TWN (actual software version V10m-TWN-XX) shows no update OTA, but is now downloading a new update in LG Bridge.
Click to expand...
Click to collapse
same for me. Only update with LG Bridge :/
H870DS SEA
Any news for H870DSU lg g6+
i need kdz can some one upload it for me?
mahmoudxcom said:
Any news for H870DSU lg g6+
Click to expand...
Click to collapse
It's out too ..
U can flash it by lgup ..
Check this one https://www.mylgphones.com/lg-g6-h8...d-oreo-8-0-update-in-hongkong-and-taiwan.html
---------- Post added at 07:20 AM ---------- Previous post was at 07:16 AM ----------
mohammadstr said:
i need kdz can some one upload it for me?
Click to expand...
Click to collapse
https://www.mylgphones.com/lg-g6-h8...d-oreo-8-0-update-in-hongkong-and-taiwan.html
not working at all. website doesnt give any link, and it seems like its a paid service
They could add V30 quad dac extra feature on our G6.?
sagor1 said:
They could add V30 quad dac extra feature on our G6.
Click to expand...
Click to collapse
See...if they add features from V30 no one will buy V30 they dont add them beacause of they want sell V30 product 1.5x price for that features without them V30 is no more than G6 only different bitween them is snapdragon 835 ...821 and some feauters
mohammadstr said:
See...if they add features from V30 no one will buy V30 they dont add them beacause of they want sell V30 product 1.5x price for that features without them V30 is no more than G6 only different bitween them is snapdragon 835 ...821 and some feauters
Click to expand...
Click to collapse
Same thing goes for s7 edge & s8.
But Samsung add every software features from s8 to s7 edge on oreo.
They even frequently update their built in apps.
sanzharis said:
not working at all. website doesnt give any link, and it seems like its a paid service
Click to expand...
Click to collapse
In this site site you can not only see any update to H870DS, as well as to download the installation package:
https://lg-firmwares.com/lg-h870ds-firmwares/
Updated mine a while ago. So far so good!
H870DS HKG-XX v20a
No ota, via LG Bridge
Updated my H870DS-TWN a few days ago, clean install via LG bridge.
No problems and nothing really extraordinary, except maybe the ability to hide the nav keys, which is less useful than I used to think. When hidden, you have to make one extra move to bring them back. Using a third party gesture control app solves the problem.
Has anyone noticed any change in battery performance or idle standby drain since updating their H870DS to Oreo? Additionally, has anyone found any problems or issues on this model since updating? I also have Taiwan version and want to check that the update is stable before I pull the trigger on it.
Guys, need help !!!
I have tried to install SEA oreo version on Indian phone via LGUP... Flash was successful (100%) but it got stuck on LG Logo..
Procedure followed for H870DS (IND)
1. Downloaded SEA Oreo KDZ File (H870DS20a_00_OPEN_SG_DS_OP_0518.kdz)
2. Installed LGUP... Made new Common folder inside C/Prog file/LG/Model
3. Extracted DLL file from KDZ & renamed it LGUP_Common.dll and kept in Common folder
4. Entered in download mode
5. Opened LGUP.. selected KDZ and Upgrade..
6. Boom.. 100% completed.. it has shown that phone is rebooting..
7. But then it got stuck on LG Screen
I cant access recovery now
I can open Hard Reset option (Vol down+Power) only.. Made hard reset but no use
I cant enter in download mode
I dont know if it is charging or not
It is not even switching off by pressing power button for long time
Pl help me...
swasha123 said:
Guys, need help !!!
I have tried to install SEA oreo version on Indian phone via LGUP... Flash was successful (100%) but it got stuck on LG Logo..
Procedure followed for H870DS (IND)
1. Downloaded SEA Oreo KDZ File (H870DS20a_00_OPEN_SG_DS_OP_0518.kdz)
2. Installed LGUP... Made new Common folder inside C/Prog file/LG/Model
3. Extracted DLL file from KDZ & renamed it LGUP_Common.dll and kept in Common folder
4. Entered in download mode
5. Opened LGUP.. selected KDZ and Upgrade..
6. Boom.. 100% completed.. it has shown that phone is rebooting..
7. But then it got stuck on LG Screen
I cant access recovery now
I can open Hard Reset option (Vol down+Power) only.. Made hard reset but no use
I cant enter in download mode
I dont know if it is charging or not
It is not even switching off by pressing power button for long time
Pl help me...
Click to expand...
Click to collapse
I had the same issue while using (with lg up and uc) Singapore rom on my indian lg DS last night and managed to recover successfully.
I made it to switch to download mode immediately after resetting while in stuck welcome screen.
Steps.
1. Keep pressing power + volume d to reboot.
2. Immediately press volume up while the usb is inserted and your official lg bridge running in your laptop and set to flash recovery mode.
3. LG bridge should recognise and start downloading the latest firmware from server and flash on your phone.
4. You may need to do factory reset after a successful flash n reboot because it might throw exceptions after booting (mine had from the process settings).