OnePlus 7T Pro tempered glass screen protector - OnePlus 7T Pro (Regular & McLaren) Accessories

Share your tempered glass screen protector for OnePlus 7T Pro here .Let's try to find out which tempered glass screen protector is the best .......

---

Anyway. glass protectors for 7TPro are the same as for the 7Pro:
https://forum.xda-developers.com/oneplus-7-pro/accessories/oneplus-7-pro-screen-protectors-t3928686
Apart from the covers, the accessories are the same, so IMHO it's better to first check the OnePlus 7 Pro Accessories section:
https://forum.xda-developers.com/oneplus-7-pro/accessories

---

Super easy install with absolutely no bubbles!
"This comes with two screen protectors, an install tool frame, a camera protector, and a carbon fiber skin for the back. I was hesitant when I saw the black frame on the screen protectors, but thought I'd give it a try.
Installation was easy. Do your typical wet towelette, clean it with the included lint free cloth, remove any extra dust with the included sticker. Then comes the easy part. I just put the install frame on, removed the backing from the screen protector to expose the adhesive and dropped it carefully into the frame. Lightly pressed all around and in the center (no squeegee needed) and that was it. No bubbles!
I immediately put the case on and you can see my ringke case isn't touching the screen protector at all. I opened the Play store to see if those black frames would block anything and I don't see a problem with it at all.
Of course the next thing to check was the fingerprint scanner. Just push thr screen some more around the fingerprint area to make sure the protector has fully stuck to the screen then it should be good. It worked with 3 of my 4 enrolled fingers and I had to re-enroll one. After that, all 4 worked.
The camera protector and carbon fiber skin were next and the camera protector was easy to put on. I had a slight difficult time aligning the skin properly but it was easy to peel while being installed.it was my first time installing a skin so I expected some difficulty,but got it on nicely.
Bottom line, for the price and what you get, I don't think anything can beat this."
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

---

Hey what screen protector is that? You didn't happen to post the name..

---

i ordered this one. tomorrow arrived normaly.
https://www.oneplus-shop.nl/nl/mocolo-oneplus-7-pro-7t-pro-9h-glazen-screen-prote.html
Verstuurd vanaf mijn HD1913 met Tapatalk

---

beaverhead said:
i ordered this one. tomorrow arrived normaly.
https://www.oneplus-shop.nl/nl/mocolo-oneplus-7-pro-7t-pro-9h-glazen-screen-prote.html
Verstuurd vanaf mijn HD1913 met Tapatalk
Click to expand...
Click to collapse
I'm using this one currently, applied it last week and it works great. Installation wasn't too difficult either.
Sent from my OnePlus7TPro using XDA Labs

---

Lossyx said:
I'm using this one currently, applied it last week and it works great. Installation wasn't too difficult either.
Sent from my OnePlus7TPro using XDA Labs
Click to expand...
Click to collapse
dont know but is this a full body protector? or have you a little space over just like the original?
Verstuurd vanaf mijn HD1913 met Tapatalk

---

beaverhead said:
dont know but is this a full body protector? or have you a little space over just like the original?
Verstuurd vanaf mijn HD1913 met Tapatalk
Click to expand...
Click to collapse
It covers the whole screen, there's only a slight space on top (because of speaker). I'm using Karbon bumper case and I don't notice any space on the edges, pretty much feels I'm using the phone without a screen protector. Hopefully I answered your question.
Sent from my OnePlus7TPro using XDA Labs

---

Lossyx said:
It covers the whole screen, there's only a slight space on top (because of speaker). I'm using Karbon bumper case and I don't notice any space on the edges, pretty much feels I'm using the phone without a screen protector. Hopefully I answered your question.
Sent from my OnePlus7TPro using XDA Labs
Click to expand...
Click to collapse
thxs for the info. im using for the moment the original cover from out of the box. have also 3 other cases. one hard and 2 crystal clear cases. lets see tomorrow[emoji106]
Verstuurd vanaf mijn HD1913 met Tapatalk

---

I ordered this one and have it on McLaren edition, with the ME case. Fits perfectly and no separaions at the corners.

---

Mguelfo said:
I ordered this one and have it on McLaren edition, with the ME case. Fits perfectly and no separaions at the corners.
Click to expand...
Click to collapse
Ordered 2 of those that come tomorrow. Hopefully, my install will be as good as yours... I've tried these LOCA installs and my very first one went fine without any issues. My second and third attempt were horrible though I'm pretty sure it was the crappy ebay protectors instead of my handiwork... lol

---

Went with WhiteStone and it is flawless.

---

doesntmatterx said:
Went with WhiteStone and it is flawless.
Click to expand...
Click to collapse
How is it applying the adhesive to the screen? That's what's holding me back.

---

it's actually not that hard just watch a couple of videos and then what I recommend is when you set everything up just do a mock-up of how you would tilt the contraption with your finger and make sure that things line up or your table is leveled. The next tip is once you get the the liquid onto the screen you can slightly move it around if it needs to go slightly up or down or to the middle before you actually start the actual process that way you can make sure the liquid will fall in the middle correctly.
In my case when I started the liquid didn't hit exactly in the middle and actually hit slightly above the middle before I let go of the PIN to drop it onto the screen so what I did is as it was opening and spreading out to the rest of the screen I actually tilted the phone towards the bottom so to make sure that it keeps spreading towards the bottom and that actually worked. other thing I did is make sure that I use tiny piece of Scotch tape to cover the headphone speakerphone on the top of the phone as well just in case.
I forgot to add after it cures make sure to reregister your finger print security scans again.

---

Hands down, Whitestone Domeglass. While they don't have one specifically for the OnePlus T Pro McLaren, the screen is identical to the 7 Pro. The back of the 7 pro is different, but the screen is the same. Not cheap but I use them exclusively.

---

doesntmatterx said:
it's actually not that hard just watch a couple of videos and then what I recommend is when you set everything up just do a mock-up of how you would tilt the contraption with your finger and make sure that things line up or your table is leveled. The next tip is once you get the the liquid onto the screen you can slightly move it around if it needs to go slightly up or down or to the middle before you actually start the actual process that way you can make sure the liquid will fall in the middle correctly.
In my case when I started the liquid didn't hit exactly in the middle and actually hit slightly above the middle before I let go of the PIN to drop it onto the screen so what I did is as it was opening and spreading out to the rest of the screen I actually tilted the phone towards the bottom so to make sure that it keeps spreading towards the bottom and that actually worked. other thing I did is make sure that I use tiny piece of Scotch tape to cover the headphone speakerphone on the top of the phone as well just in case.
I forgot to add after it cures make sure to reregister your finger print security scans again.
Click to expand...
Click to collapse
Mike02z said:
Hands down, Whitestone Domeglass. While they don't have one specifically for the OnePlus T Pro McLaren, the screen is identical to the 7 Pro. The back of the 7 pro is different, but the screen is the same. Not cheap but I use them exclusively.
Click to expand...
Click to collapse
What cases are you using with your Whitestone protector?
I just ordered my phine, going to get the Whitestone Dome , and want to find some cases that are compatible.
Sent from my SM-G965U using Tapatalk

---

gravitywell said:
What cases are you using with your Whitestone protector?
I just ordered my phine, going to get the Whitestone Dome , and want to find some cases that are compatible.
Sent from my SM-G965U using Tapatalk
Click to expand...
Click to collapse
It just came today. I've never had an issue with any of my phone cases with any of my phones using done glass. I expect the case that comes with the McLaren will work. I'll post after I install it tomorrow.

---

I just installed the Domeglass. It works fine with the McLaren case. Not lifting.

---

Here is mine after completion with the McLaren case on it

---

I still use the McLaren case cause it's still the best both in feel and aesthic.
I've tried a bunch of cases, poetic etc all the name brands but they take away too much from the overall feel. Either too bulky it bumpy or too thick.
Still haven't found one that is both sleek and doesn't take too much away. Still searching...
Btw none of them had a negative affect on the white dome.