My coolpad Note 3 completely dead after flashing a stock Rom using SP Tool (formate all +Download). when i connect to charger nothing happens but if I connect mobile to PC preloader vcom driver appears and flashing file always successful. I tried switching battery as well but nothing seems to work.
Model: 8676 I02
S/W ver : v5.1-024
H/W ver : P1
Rom I flashed : 8676_I02_5.1-V34
Related
i have lenovo a3000 with the latest firmware upgrade
yesterday,i charge it in power off and when i wanna turn on it a3000 wont turn on
no indicator battery,cant power on,but detect on device manager (i pressed power+volume up but just for 2 second and the driver [mtk usb com] dissappear)
so i download factory rom n the latest sp flashtool
i found problem in download the original rom on sp flashtool
the code error 4001
i think its driver problem
then i follow yuweng guide http://forum.xda-developers.com/show....php?t=1943442
i cant find Test Point on my pcb tab
any ideas?please help me :crying:
Hi..
I Have a problem with my Acer Liquid E2 Dual Sim..
Before this, my problem is the phone was stuck in the Ace green logo (Bootloop) and i tried to flash it using SP flash tool, and it flashed succesful until the green circle, but my device gotten even worse, now when i turn on the power, it just vibrate once and continue in blank screen only..and when i try to connect it to the pc, it recognize with a vibrate and blue led turning on, but in the device manager, it detects as MTK USB Port, the is no MTK Preloader or any driver except the mtk usb port
I already googled it, and it seems because i flashed the wrong preloader (it means i used the wrong firmware in the spflashtool), but i downloaded it from the global acer download, And another information i get that my device is in a condition where it enters the low-layer download interface of the MT65xx device (AFAIK).. Thats why it only detects as MTK USB Port. So what to do now? I have tried using SPFlashTool to Dwonload only the preloader checked using from two different rom, but no success both? already tried any different version spflashtool
Every time i tried to download the preloader to the device using spflashtool it just shows "dram failed"
like this
"BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM Failed!"
Does anyone knows how to fix it
Anyboy can help me pleaasee
lukerodriguez said:
Anyboy can help me pleaasee
Click to expand...
Click to collapse
i have same problem bro, is your phone already fix?
Hi,
I have infinix hot note pro [mt6592] 2 GB ram+16 GB rom version. I somehow bricked it while I was flashing custom recovery. Now my device isn't turning on but it is connected with my PC as usb preloader but it is not dectected by SP flash tool so that i can flash stock rom. USB DA drivers are not being installed, when i install them then error comes that this device cannot start. And my mobile isn't detected by pc as any other mediatek usb device, it is just connected as USB preloader vcom device. Please help me. I'll be very thankful. Please :crying:
Aoa.Check your inbox.
pls help me out sp flash tool cant detect my coolpad 8675 phone when i want to flash my phone an i hv installed coolpad setup driver, mtk driver, Vcom driver, mtk preloader Vcom usb port on my laptop till is not see my phone pls help me how to fix it, an i hold up volume bottom till sp flash tool can not detect my coolpad 8675 phone i till use YGDP to flash till is cant see my phone pls help me,
I'm trying to install stock rom to Lenovo a2016a40 (Lenovo B). After I connect phone to my system using volume down key preloder appears in device manager but after few seconds it disconnects from pc. I have tried to install via SP flash tool but it fails and gives error.
I have tried to update all mediatek drivers , changed port and cables but still I'm facing that issue , please help with this issue.
@sangram200
AFAIK Lenovo Vibe B is based on Mediatek chipset, hence SP Flash Tool seems to be the correct one.
It just disappeared from Device manager on PC
It simply disconnects from pc after few seconds ( disappeared from device manager), hense SP tool fails there is no issue with flash tool , its the connectivity issue but I don't understand why it disconnects from PC ,I have tried to update drivers and changed cables and switched ports but still having same issue.
@sangram200
I'm pretty sure you haven't installed the correct USB-drivers as needed, for example the MediaTek MT65xx USB VCOM Driver: this USB Driver will make sure that your MediaTek Android device is properly recognized by your PC, it ensures that there will be no hiccups while you are trying to flash a custom ROM or when you are trying to root your device.