hello all
i buy device on ebay and flash this ROM
https://forum.freaktab.com/forum/tv...29-mxq-pro-4k-v1-0-p201-s905-amlogic-firmware
and for now it not boot ust black screen
pls help to unbrick device i cant get infro and cant reconized device to find rom for this
on cpu it name s905m-d
Bricked D905 also
I've got this same box. Stops at mbox logo at boot. No recovery. Did you ever find a fix? The link above is dead.
Tullyp
UPDATE FOR ANYONE WITH THIS BOX: This bricks because it is a "junk clone Chinese" box. Just as yours in your pictures, my board reads as a P201, but it is not. It is a p211 (p212). The original recovery also shows as a p201, but can't even wipe cache or data because it is a mismatch. I can not find anything to unbrick. Tried everything, but you can run Libreelec and Coreelec thru USB port. By putting in a "burn image" in SD slot. Will fail to burn but after a few seconds will boot from USB. ( Does this mean boatloader OK?) I will not give up. I'm waiting for a UART chip I ordered to connect via serial. Don't know what I'll find.
Related
Some wanker had posted wrong images for boot and recovery for S6000L. And since I'm a moron, i didn't take the files apart to check them.
Installing them bricked my tablet. So essentially I have no boot or recovery images on the device and was wondering if there's any way to revive it.
Tablet freezes if i start it in normal, fastboot or recovery modes, so that's out of the picture.
However, i think that "meta mode" still works (if indication of it working is displaying lenovo logo and having "meta mode" written on the bottom of the screen)
It's getting detected on "mediatek preloader usb vcom port" for a couple of seconds when connected to the PC, which means that i might be able to use adb to push a backup into the tablet (?)
Been scouring the internet for a while with no results. Is there, by any chance, anyone who can help me out?
Hi guys, I recently purchased a Homtom HT3 for my mother, when it arrived to me I charged it and checked it out a bit just to make sure everything was fine which it was.
She collected it from me the next day and told me she'd start to use it the day after, she calls me up the next day and tells me there's some problems with it and a few people at her workplace tried to fix it for her to no avail. I pick the phone back up and I notice that everytime I power it on, it gets stuck on the "homtom" logo.
As I don't know too much about fixing phones I only took the following steps before asking for advice here; I went into recovery mode by holding up volume and power button, the android guy with the red triangle appeared so I tapped up + power button to get into the recovery(?) menu. I wiped the phone to factory settings and deleted the cache in there but it hasn't fixed the problem.
I assume I need to flash a firmware or something to potentially fix this, but I'm unable to find an official firmware from doogee/homtom's site for the HT3. I've found a firmware that I downloaded from "chinagadgetsreviews" but I'm a bit weary to try and flash with that rom because it isn't from the manufacturer. (even if I knew how to - the only experience I have is rooting my own phone but that's when I actually had access to a working phone, not one thats stuck on a boot logo).
Sorry for the long post but could anyone guide me in the right direction here? TIA
I'm not opposed to not using official firmware, I think I use cyanogen mod(?) on my own phone. I'd just like the problem fixed in the easiest way possible.
Trying to fix it myself by flashing a rom via SP flash tools but I've ran into another problem which is stopping any kind of progress - the phone isn't detected in Windows, I can't enable usb debugging because I can't get passed the boot loop, I've tried installing the ADB driver manually which didn't seem to work (just said it didn't install correctly and left me with a yellow exclamation mark) and I tried to install it automatically via ADB driver installer but it just throws up an error that the device isn't detected.
Any help would be greatly appreciated.
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Same here - any solution for this problem?
Kleos89 said:
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Click to expand...
Click to collapse
Hello everyone;
I was trying to load a CM recovery file on my cell by using SP Flash tools and somehow bricked my Acer Z410 phone (carrier: Fido, 2 sim card slot) I do not know why afterwards, the cell turns white with a yellow strip down the middle. I have been able to have my computer recognize it after numerous attempts to flash firmware versions that I was not quite sure was the original. I had tried your site to load the firmware that seem to correlate to my cell configurations, but all of the links are dead. I ended up flashing with SP Flash tools firware version AVOKO 1.015, but it still can't boot in to see anything on cell. So as of today, I got my computer to recognize the phone and I can actually see the files on my phone and sd card inside. How can I boot into this puppy? I have tried within ABS and the command function to view adb devices, but it does not show up? I get an error : device 0123456789ABCDEF Unauthorized. In my device manager it shows up as ACER phone , and under the Ports section it does show Mediatek Preloader USB VCOM driver (COM 5). I hope I have given enough information to start diagnosing the problem.
Any suggestions how to go about this problem from here?
breezin123
Hi , my x96Air v2, 4/32 is stuck on logo and i cant access recovery mode to do a hard reset , is there any solution ?
and can anyone help me please.
PS i can flash roms using the sd card or Amlogic usb burning tool.
I also have an X96Air, 4/32....
After flasching my Image nothing happens on startup.
It takes a while until the logo appears. This is when the device comes to the emergency upload mode. This is the moment where the device becomes recognized by the usb burning tool from amlogic. (when drivers are correctly installed)
Be patient... after fail boots my device always comes back to an emergency upload mode after some time.
Stil searching the Backup of the Device with AM7256 Wifi chip. Have you this Backup?
rogi1 said:
I also have an X96Air, 4/32....
After flasching my Image nothing happens on startup.
It takes a while until the logo appears. This is when the device comes to the emergency upload mode. This is the moment where the device becomes recognized by the usb burning tool from amlogic. (when drivers are correctly installed)
Be patient... after fail boots my device always comes back to an emergency upload mode after some time.
Stil searching the Backup of the Device with AM7256 Wifi chip. Have you this Backup?
Click to expand...
Click to collapse
no i don't have it sorry
I have a T9 4GB/64GB TV BOX (RK3328) TV stick, it got bricked. I tried all method to get it boot in maskrom mode but no luck. was flashing firmware its failed.
now my box not turning on.
I used flash tool to flash T9-4_64-RK3328-6255-v9-1228_AndroidTVBox image file. I attached flash log file and board image
I have no ideas, anyone please help!
Same Issue with me. it is dead, if you have found any solution just tell me
I was able to get it in maskrom mode by shorting these point
zee95 said:
I was able to get it in maskrom mode by shorting these pointView attachment 5661685
Click to expand...
Click to collapse
Hi @zee95 , I have the same problem, I bricked it trying to flash it, now it doesn't turn on not even the boot led nor recognized by PC when I plugged it with usb
Can you guide me please with the steps you followed to unbrick, how did you shorten those points. Thanks in advance @zee95
How you are flashing rom ?
The one i used with an incorrect firmware was Factory Tool v 1.46.
After that the box never turned on, nor even the t9 boot screen or the blue front leds. Also unable to been recognized by any flash tool.
I have tried with SD Card with firmware (using Rockchip Create Upgrade Disk) , hit reset button and power on, but nothing.
Also tried shortening with a clip and needle the two points you mentioned in the picture and plug the power cable at the same time but nothing.
Regards
Having same problim
when ever i connect to pc its in maskrom mode and cant exit from it
plz help