Hi , my x96Air v2, 4/32 is stuck on logo and i cant access recovery mode to do a hard reset , is there any solution ?
and can anyone help me please.
PS i can flash roms using the sd card or Amlogic usb burning tool.
I also have an X96Air, 4/32....
After flasching my Image nothing happens on startup.
It takes a while until the logo appears. This is when the device comes to the emergency upload mode. This is the moment where the device becomes recognized by the usb burning tool from amlogic. (when drivers are correctly installed)
Be patient... after fail boots my device always comes back to an emergency upload mode after some time.
Stil searching the Backup of the Device with AM7256 Wifi chip. Have you this Backup?
rogi1 said:
I also have an X96Air, 4/32....
After flasching my Image nothing happens on startup.
It takes a while until the logo appears. This is when the device comes to the emergency upload mode. This is the moment where the device becomes recognized by the usb burning tool from amlogic. (when drivers are correctly installed)
Be patient... after fail boots my device always comes back to an emergency upload mode after some time.
Stil searching the Backup of the Device with AM7256 Wifi chip. Have you this Backup?
Click to expand...
Click to collapse
no i don't have it sorry
Related
Hello,
During the past days I've been trying to flash my C7 with no success. When pressing power button, it turns on and displays the Alcatel logo but stays there, it does not load the OS.
I have tried to use SPtools to flash it, I have the mtk drivers installed in my PC. When I plug the switched-off phone to the computer it turns on and couple seconds after my PC detects it (I can see the preloader mtk loaded on the device manager); however, one second right after it is detected, it is disconnected as it keeps booting to show the logo and stay there. Obviously, if the phone is not detected I cannot use SPtools to flash it.
Any suggestion will be highly appreciated.
PS: I have also tried to connect to it with adb, and dump a ROM using sideload with no sucess, the PC recognizes it from the recovery but after copying the image nothing new happens on reboot.
Some wanker had posted wrong images for boot and recovery for S6000L. And since I'm a moron, i didn't take the files apart to check them.
Installing them bricked my tablet. So essentially I have no boot or recovery images on the device and was wondering if there's any way to revive it.
Tablet freezes if i start it in normal, fastboot or recovery modes, so that's out of the picture.
However, i think that "meta mode" still works (if indication of it working is displaying lenovo logo and having "meta mode" written on the bottom of the screen)
It's getting detected on "mediatek preloader usb vcom port" for a couple of seconds when connected to the PC, which means that i might be able to use adb to push a backup into the tablet (?)
Been scouring the internet for a while with no results. Is there, by any chance, anyone who can help me out?
Hi everyone, i ask for your help cause i have a common problem but the fixes i found in the forum didn't work for me: my ZenFone 5 stucks at "Asus" logo with a "loading loop" wheel below that.
I know this post may be long but i beg you to read all steps:
1) Phone stucks at logo, but could enter recovery (pressing vol + down), i've updated it via external SD card (official firmware but didn't work) then i've wiped data and did a factory reset. Phone still stucks at logo.
2) Now i can't even enter recovery mode... when pressing vol + down it shows 2 options but whatever i choose the phone reboots. If i press vol + up it says "CSC mode, long press power to restart. Phone still stucks.
3) Now (after some time) the phone's screen doesn't show anything, nor charging icon or notification led when recharging, but strangely the computer recognizes it as a device when connected via USB cable, and the led turns on when i do this.
A friend told me to follow a guide that says to install "Intel Soc USB driver", i did that. After installing, when connecting the device, 2 things should pop up in Device Mangager under "Intel Soc": CloverviewPlus Device and Intel Soc USB Driver... but the second one doesn't show to me
I've also tried Asus flashtool guide... at step 4 it says to click in the box icon and choose the firmware RAW file, so i've downloaded a raw firmware for the ZenFone 5, but oddly it doesn't let me choose any raw file.
Note: the phone is recognized by the pc as "QHSUSB_BULK", so i've tried to update its driver with qualcomm drivers, and now it's recognized as "Qualcom MMC Usb storage device". But i think i've did a wrong thing cause my friend told me i should have choosed some kind of official driver
Thanks in advance for your help
my lenovo a7000 doesn't turn on, can't go to recovery mode. also my first hardbrick experience. desperate for help.
whenever i use spflashtools to download a fresh stock rom to my phone, it always shows this problem
"BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)"
I've also tried to format it, but the same problem comes up.
Then I saw this vid. It's about fixing any bricked china phone.
"How to Unbrick every MTK China Phone ! Preloader / SP Flashtool Fix [HD]"
(pls search it on youtube if you like. somehow i couldn't post links.)
I don't know, but I think this vid is trying to fix those phones that aren't recognized by the PC. But mine is recognized. It comes up on the Device Manager as a MTK USB Port (COM10) with the battery on. But it keeps on getting disconnected and reconnected again. But this stops when I remove the battery, put the battery back on, click on download on the spflashtools, then connect the USB. The error will appear, but somehow the connection becomes stable.
Also this video talks about META mode. With the battery out, I tried all of the key combinations to enter this mode, without success whatsoever. If you know something, pls. share.
Maervince015 said:
my lenovo a7000 doesn't turn on, can't go to recovery mode. also my first hardbrick experience. desperate for help.
whenever i use spflashtools to download a fresh stock rom to my phone, it always shows this problem
"BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)"
I've also tried to format it, but the same problem comes up.
Then I saw this vid. It's about fixing any bricked china phone.
"How to Unbrick every MTK China Phone ! Preloader / SP Flashtool Fix [HD]"
(pls search it on youtube if you like. somehow i couldn't post links.)
I don't know, but I think this vid is trying to fix those phones that aren't recognized by the PC. But mine is recognized. It comes up on the Device Manager as a MTK USB Port (COM10) with the battery on. But it keeps on getting disconnected and reconnected again. But this stops when I remove the battery, put the battery back on, click on download on the spflashtools, then connect the USB. The error will appear, but somehow the connection becomes stable.
Also this video talks about META mode. With the battery out, I tried all of the key combinations to enter this mode, without success whatsoever. If you know something, pls. share.
Click to expand...
Click to collapse
Hi!
I had the same issue 2 day before!
To fix it I was unable with windows,so I downloaded a spflashtool for linux. I started with sudo (root access) and made the same method with the windows version.Its worked for me! But wait one or two day,maybe somebody will know a solution with windows.
My Lenovo A7000 Does not turn on
While installing the official update marshmallow device switched of and then it does not turn on. If i put in charge then after sometime lenovo screen appears and the it shuts down again,. Cannot go to recovery mode also. The lenovo screen shows TOOL Dl image fail in the left bottom side.
How can i solve this problem Please someone help me:crying::crying::crying:
Hi guys, I recently purchased a Homtom HT3 for my mother, when it arrived to me I charged it and checked it out a bit just to make sure everything was fine which it was.
She collected it from me the next day and told me she'd start to use it the day after, she calls me up the next day and tells me there's some problems with it and a few people at her workplace tried to fix it for her to no avail. I pick the phone back up and I notice that everytime I power it on, it gets stuck on the "homtom" logo.
As I don't know too much about fixing phones I only took the following steps before asking for advice here; I went into recovery mode by holding up volume and power button, the android guy with the red triangle appeared so I tapped up + power button to get into the recovery(?) menu. I wiped the phone to factory settings and deleted the cache in there but it hasn't fixed the problem.
I assume I need to flash a firmware or something to potentially fix this, but I'm unable to find an official firmware from doogee/homtom's site for the HT3. I've found a firmware that I downloaded from "chinagadgetsreviews" but I'm a bit weary to try and flash with that rom because it isn't from the manufacturer. (even if I knew how to - the only experience I have is rooting my own phone but that's when I actually had access to a working phone, not one thats stuck on a boot logo).
Sorry for the long post but could anyone guide me in the right direction here? TIA
I'm not opposed to not using official firmware, I think I use cyanogen mod(?) on my own phone. I'd just like the problem fixed in the easiest way possible.
Trying to fix it myself by flashing a rom via SP flash tools but I've ran into another problem which is stopping any kind of progress - the phone isn't detected in Windows, I can't enable usb debugging because I can't get passed the boot loop, I've tried installing the ADB driver manually which didn't seem to work (just said it didn't install correctly and left me with a yellow exclamation mark) and I tried to install it automatically via ADB driver installer but it just throws up an error that the device isn't detected.
Any help would be greatly appreciated.
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Same here - any solution for this problem?
Kleos89 said:
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Click to expand...
Click to collapse