Hello,
i installed a system image, and unsuccessfully, I only have a black screen, I can't get into a fastboot. the cellphone did not charge or anything when it could be charged.
tinti1998 said:
Hello,
i installed a system image, and unsuccessfully, I only have a black screen, I can't get into a fastboot. the cellphone did not charge or anything when it could be charged.
Click to expand...
Click to collapse
Do you have something like "Qualcomm HS-USB QDLoader 9008" in the device manager?
tinti1998 said:
Hello,
i installed a system image, and unsuccessfully, I only have a black screen, I can't get into a fastboot. the cellphone did not charge or anything when it could be charged.
Click to expand...
Click to collapse
You are currently in EDL mode, you can retrieve your phone using MiFlash with Authorized Account.
But curiously, what system image you have flashed on your device that cause this?
MarcusMario0605 said:
You are currently in EDL mode, you can retrieve your phone using MiFlash with Authorized Account.
Click to expand...
Click to collapse
Hi, you know any reliable user with an authorized account? I have a SoftBricked A3.
Related
Hello i have bricked my k910.
i flashed a new firmware with twrp and while flashing phone restart.
now im stuck on lenovo logo..
fastboot detect the phone but locked bootloader.
I test with qpst but Qualcomm HS-USB QDLoader 9008 is loaded 2-3 seconds and then the phone goes back to fastboot mode.
no blue LED.
now i disconnect the battery from the phone and only connect with usb+ "volume +, same problem... only detect the Qualcomm HS-USB QDLoader 9008 for few seconds.
what can i do now?
i tested already to click fast as possible to download in emmc software.. dont work.
i flashed before it brick twrp
and the system folder is empty :cyclops:
what can i do now?
gekkorist said:
Hello i have bricked my k910.
i flashed a new firmware with twrp and while flashing phone restart.
now im stuck on lenovo logo..
fastboot detect the phone but locked bootloader.
I test with qpst but Qualcomm HS-USB QDLoader 9008 is loaded 2-3 seconds and then the phone goes back to fastboot mode.
no blue LED.
now i disconnect the battery from the phone and only connect with usb+ "volume +, same problem... only detect the Qualcomm HS-USB QDLoader 9008 for few seconds.
what can i do now?
i tested already to click fast as possible to download in emmc software.. dont work.
i flashed before it brick twrp
and the system folder is empty :cyclops:
what can i do now?
Click to expand...
Click to collapse
did you see my solution for the COM/USB port problem here?
Unfortunately i'm facing a bigger isue atm :crying:
Crowds said:
did you see my solution for the COM/USB port problem here?
Unfortunately i'm facing a bigger isue atm :crying:
Click to expand...
Click to collapse
Hey, test with USB Extansion but dont work... or is 1 Meter to short?
gekkorist said:
Hey, test with USB Extansion but dont work... or is 1 Meter to short?
Click to expand...
Click to collapse
humm...not sure, mine has 4mts and it worked on 1st try
usefull tool in one place
Feel free to link your ideas :good:
http://forum.xda-developers.com/and...-tools-one-t2887839/post55673946#post55673946
Thank you
Crowds
i have the same issue, do you have a solution??
i try using a usb expansion of 10 Mts and i have the same issue, not boot no nothing.
luis0n said:
i have the same issue, do you have a solution??
i try using a usb expansion of 10 Mts and i have the same issue, not boot no nothing.
Click to expand...
Click to collapse
Sorry but that's the only solution. The one I've wrote on xda.
In fact its quite easy, the problem is when we ended up without it we stressed
For the first time it took me 1 month but then, after that experience, I've manage to make it work after 5 min. And believe me, since the first time, I've broken mine more than 20 times
Sent from my Lenovo K910 using Tapatalk
gekkorist said:
Hello i have bricked my k910.
i flashed a new firmware with twrp and while flashing phone restart.
now im stuck on lenovo logo..
fastboot detect the phone but locked bootloader.
I test with qpst but Qualcomm HS-USB QDLoader 9008 is loaded 2-3 seconds and then the phone goes back to fastboot mode.
no blue LED.
now i disconnect the battery from the phone and only connect with usb+ "volume +, same problem... only detect the Qualcomm HS-USB QDLoader 9008 for few seconds.
what can i do now?
i tested already to click fast as possible to download in emmc software.. dont work.
i flashed before it brick twrp
and the system folder is empty :cyclops:
what can i do now?
Click to expand...
Click to collapse
hi ,
I have a same problem . I can't activate download mode . It works 2-3 seconds and then the phone goes back to fastboot mode.
Did you find a solution ?
luboii said:
hi ,
I have a same problem . I can't activate download mode . It works 2-3 seconds and then the phone goes back to fastboot mode.
Did you find a solution ?
Click to expand...
Click to collapse
Hi,
no, have no solution. I try all tutorials and usw all Tricks i found in the Internet. Opst, miflash, nothing work. The 2-3 secs in donwloadmoade without a blue led is to short.
I try the tutorials on 6 different computers. Nothing.
I contact the Lenovo support in germany, usa and china, no help..
I found 2 services to unbrick the k910 with a own jtag
1 in Malaysia and 1 in romainia. But i dont trust this peoples.
I buy a new phone and put the k910 in a corner.
Sorry.
Lenovo phone... Never again
any news guy? had same problem with mine. already buy a new battery btw. sighh! when using miflash my phone didt disconnected from download mode but ended with error, while using qpst it keep connect then few second disconnected till my pc get bsod.
Send my phone I offer repair brick k910
This morning I decided I'd try to install CM14.1 instead of what I was running at the time, MIUI8. I must have flashed the wrong Official ROM and everything has gone downhill since then. I've also asked reddit for some advice and was told to install official developer ROM through EDL. That has been my goal for the last few hours but I haven't managed to do it yet. I believe I am accessing EDL but I don't really know how to tell, through Device Manager I see "Qualcomm HS-USB Diagnostics 900E (COM3)" but cannot flash through MiFlash as no device appears. When I am in fastboot I can see my device through MiFlash but cannot flash anything to it as I get "mismatching image and device" even though I am 95% sure that this is the correct ROM I should be flashing.
Please help I am beginning to stress out, any questions I will answer them quickly!
You must flash in edl mode
How to get from fastboot to edl
http://forum.xda-developers.com/redmi-note-3/how-to/guide-reboot-to-edl-mode-fastboot-test-t3398718
mar.ur said:
You must flash in edl mode
How to get from fastboot to edl
http://forum.xda-developers.com/redmi-note-3/how-to/guide-reboot-to-edl-mode-fastboot-test-t3398718
Click to expand...
Click to collapse
Thanks for the post, unfortunately I am having troubles getting into EDL. With the program you just linked I get stuck at "< waiting for device >". I believe there could be some driver issues as I am getting 900E and not 9008.
you need a deep flash cable for that...
here you go,
http://en.miui.com/thread-310325-1-1.html
This one is a little bit tricky but quicker and less aggressive way.
http://en.miui.com/thread-380827-1-1.html
This one is easier but you will have to sacrifice one of your USB cable ( if you have an extra one lying around)
Personally first one worked for me well..
Hit thanks if this helped.
I have tried with the deep flash cable, no luck. The second link talks about browsing to the correct drivers.. where do I get these, what is he talking about?
follow this method , drivers must be installed properly
http://en.miui.com/thread-235865-1-1.html
mar.ur said:
follow this method , drivers must be installed properly
http://en.miui.com/thread-235865-1-1.html
Click to expand...
Click to collapse
How do I start fresh? I've already got drivers that will interfere. As in, he says "Phone will be detected as QHUSB_BULK" where for me it's being detected already as the 900E one.
since you have installed a wrong rom package,you device name and status get changed. during flashing from mi flash choose to clean all. always use miflash beta
gaurav1322 said:
since you have installed a wrong rom package,you device name and status get changed. during flashing from mi flash choose to clean all. always use miflash beta
Click to expand...
Click to collapse
Okay I will remember that when I get to the point of flashing but I think that is still quite far away.
Sivi.N4 said:
How do I start fresh? I've already got drivers that will interfere. As in, he says "Phone will be detected as QHUSB_BULK" where for me it's being detected already as the 900E one.
Click to expand...
Click to collapse
You can still try the "update driver" option...As after the driver installation windows refreshes the connection and if everything goes well..Your phone will be detected as 9008
You probably already know at this point, but if you don't, the notification LED on the device will flash red when you have successfully entered EDL mode.
You can try popping open the back cover(remember to eject the sim card tray) slowly(the fingerprint scanner is connected to the back), then unplug and replug the battery. It might help you boot to fastboot.
Hope this helps.
Good luck.
Ivanlai said:
You probably already know at this point, but if you don't, the notification LED on the device will flash red when you have successfully entered EDL mode.
You can try popping open the back cover(remember to eject the sim card tray) slowly(the fingerprint scanner is connected to the back), then unplug and replug the battery. It might help you boot to fastboot.
Hope this helps.
Good luck.
Click to expand...
Click to collapse
The notification LED blinks red anytime that the phone is connected to the computer so it is hard to tell whether I am in EDL mode or not. My main problem right now is that I can't seem to get the Device Manager to say 9008 instead of 900E and therefore I cannot see it in MiFlash. Anyone else have any suggestions?
Sivi.N4 said:
The notification LED blinks red anytime that the phone is connected to the computer so it is hard to tell whether I am in EDL mode or not. My main problem right now is that I can't seem to get the Device Manager to say 9008 instead of 900E and therefore I cannot see it in MiFlash. Anyone else have any suggestions?
Click to expand...
Click to collapse
I faced same issue I solved by tearing it down and use test points to get to edl
So one evening I was tired and tried to flash a zip using TWRP sideload. After flashing I wanted to reboot but accidentally pressed "System B" and before I fully realized what I've done I rebooted the phone. Now the system info LED (the one you get when something is bricked) starts blinking whenever my phone is connected to a charger or to the PC.
It gets recognized as Qualcomm HS USB qdloader 9008. Is there any way to change it back to System A using Sahara Protocol or something like that?
Polyparadox said:
So one evening I was tired and tried to flash a zip using TWRP sideload. After flashing I wanted to reboot but accidentally pressed "System B" and before I fully realized what I've done I rebooted the phone. Now the system info LED (the one you get when something is bricked) starts blinking whenever my phone is connected to a charger or to the PC.
It gets recognized as Qualcomm HS USB qdloader 9008. Is there any way to change it back to System A using Sahara Protocol or something like that?
Click to expand...
Click to collapse
No. We need a blankflash and motorola are scared little kids so they dont releae it because it can cause "security breaches"
Meh...
Thanks for the reply.
Polyparadox said:
Meh...
Thanks for the reply.
Click to expand...
Click to collapse
Sorry that this didn't have a happy ending ;-;
Hello,
I have my Pocophone for 2 months now. I installed Lineage OS 16.0 succesfully and everything was working perfect. Out of nothing I got a blue screen and now my phone won't turn on anymore. When I connect it to my laptop , the device is seen as Qualcomm HS-USB QDLoader 9008. Looks like it's bricked...
Can someone help me to unbrick it?
Thanks in advance.
Greetings,
Bjarnie
have you tried ADB??
santiagoruel13 said:
have you tried ADB??
Click to expand...
Click to collapse
Not yet.. but can’t get in fastboot mode, so that’s not possible I think
You mean , your phone cant boot to fastboot mode??
---------- Post added at 03:27 PM ---------- Previous post was at 03:26 PM ----------
Fastboot reboot bootloader..
Have you tried that???
santiagoruel13 said:
You mean , your phone cant boot to fastboot mode??
---------- Post added at 03:27 PM ---------- Previous post was at 03:26 PM ----------
Fastboot reboot bootloader..
Have you tried that???
Click to expand...
Click to collapse
Yes, the phone won’t boot to fastboot mode with arrow up and power button. Will try it with laptop later today..
Fastboot mode is volume down button + power button.
Just connect the phone to pc. .then hit adb.
Then run the command
Adb reboot bootloader..
KabalLV said:
Fastboot mode is volume down button + power button.
Click to expand...
Click to collapse
Both not working, - and +.
santiagoruel13 said:
Just connect the phone to pc. .then hit adb.
Then run the command
Adb reboot bootloader..
Click to expand...
Click to collapse
Not working.. device isn’t recognized in cmd
Bjarnie said:
Hello,
I have my Pocophone for 2 months now. I installed Lineage OS 16.0 succesfully and everything was working perfect. Out of nothing I got a blue screen and now my phone won't turn on anymore. When I connect it to my laptop , the device is seen as Qualcomm HS-USB QDLoader 9008. Looks like it's bricked...
Can someone help me to unbrick it?
Thanks in advance.
Greetings,
Bjarnie
Click to expand...
Click to collapse
Go to
https://miui.blog/any-devices/qualcomm-qpst-tool/
As per my guess, your device is in EDL mode. I think you could directly flash fastboot rom to it in MiFlash tool, while it is seen as Qualcomm HS-USB QDLoader 9008.
ayush2901 said:
As per my guess, your device is in EDL mode. I think you could directly flash fastboot rom to it in MiFlash tool, while it is seen as Qualcomm HS-USB QDLoader 9008.
Click to expand...
Click to collapse
See the results.. unf not working.
Sydtek said:
Go to
https://miui.blog/any-devices/qualcomm-qpst-tool/
Click to expand...
Click to collapse
Thanks! I tried it without any result yet. Tried different roms/configs but everytime it ends with an error
Try to google the error's and see what you can find out about them.
Bjarnie said:
Thanks! I tried it without any result yet. Tried different roms/configs but everytime it ends with an error
Click to expand...
Click to collapse
Did you solved this? i have the same problem
alanleonardi said:
Did you solved this? i have the same problem
Click to expand...
Click to collapse
Are you using Intel or AMD Ryzen PC? Use Intel PC and use Miflash to flash the stock ROM.
hi
did you solve your problem? i have the same issue and no one can fix it
i have exactly the same problem with poco f1 and unfortunately no one knows what is these errors
some says it is because authorized account but when authorizes account be needed its error appear wile flashing not error of cannot receive hello pocket or can not read com port
I think it happpened because of wrong firmware? I already experienced this to my son's bricked tablet. which is LG Gpad v400 i flashed the wrong firmware which firmware of Gpad V410 and end up to bricked tablet. I think the only solution for that is jtag. Try to Search for pocophone jtag.
HELLO PACKETS ERROR
happened to me with Redmi3s
i tried possibly everything related to DRIVERS, ROMS, MIFLASHER VERSIONS, FASTBOOT ROM VERSION , STORED THEM IN SAPERATE LOCATION WITH SMALLER NAMES, TRIED ON TWO DIFFERENT PC (WIN10 / WIN7,) USED DIFFERENT CABLES, TRIED QUALCOME QLOADER METHOD
USING BLADE, I CUT THE GLUE AND OPENED THE PANEL BEHIND, used TEST POINT SHORT CIRCUIT METHOD , REMOVED BATTERY AND CHARGED OVERNIGHT
BUT
redmi3s NEVER resuscitated ...
Hi,
My OnePlus 7T PRO (HD1901) got bricked. It is not starting nor showing any signs of loading fastboot. Apparently, the charging is not working either.
I tried plugging it into the computer. Saw the BULK device under Ports. I installed Qualcomm and it's showing "QUALCOMM HS-USB QDLoader 9008". When I tried running MSM, it gives me an error "Firehose GetUfsInfo Failed". I tried pressing the power + Up arrow keys for a few seconds, which switches it off and then + - power together. MSM says "Connected" but each time i start it, it gives the same error.
Please help as I am not able to figure out how to resolve this.
vipul20044 said:
Hi,
My OnePlus 7T PRO (HD1901) got bricked. It is not starting nor showing any signs of loading fastboot. Apparently, the charging is not working either.
I tried plugging it into the computer. Saw the BULK device under Ports. I installed Qualcomm and it's showing "QUALCOMM HS-USB QDLoader 9008". When I tried running MSM, it gives me an error "Firehose GetUfsInfo Failed". I tried pressing the power + Up arrow keys for a few seconds, which switches it off and then + - power together. MSM says "Connected" but each time i start it, it gives the same error.
Please help as I am not able to figure out how to resolve this.
Click to expand...
Click to collapse
Unfortunately you will need a MSM tool which has Authorised access to flash in EDL mode.
Basically only Service Center have access to such tools.
You can find third party repair personel online.
mvikrant97 said:
Unfortunately you will need a MSM tool which has Authorised access to flash in EDL mode.
Basically only Service Center have access to such tools.
You can find third party repair personel online.
Click to expand...
Click to collapse
I did mention i tried MSM but i am getting an error
vipul20044 said:
I did mention i tried MSM but i am getting an error
Click to expand...
Click to collapse
You will need patched firehose to flash the phone using MSM.
mvikrant97 said:
Unfortunately you will need a MSM tool which has Authorised access to flash in EDL mode.
Basically only Service Center have access to such tools.
You can find third party repair personel online.
Click to expand...
Click to collapse
I did mention i tried MSM but i am fert
mvikrant97 said:
You will need patched firehose to flash the phone using MSM.
Click to expand...
Click to collapse
Thanks. Any guidance on where to get it from and how to go about it?
vipul20044 said:
I did mention i tried MSM but i am fert
Thanks. Any guidance on where to get it from and how to go about it?
Click to expand...
Click to collapse
The tool is a paid one and I cannot discuss about it here due to XDA policies.
I would recommend you to search online for flashing service.
SMT mode I think it was called on msm tool. It fixed my phone but wipes IMEI. At least the phone works now
if device not have signal's then dm me I'll try recover. make sure you'll be my tester it's NOT tested yet
or anyone else facing the trg error etc then let me know I'll try make file if anyone is here to test
cbomb1337 said:
SMT mode I think it was called on msm tool. It fixed my phone but wipes IMEI. At least the phone works now
Click to expand...
Click to collapse
Index of /list/Unbrick_Tools/OnePlus_7T
Try this msm tools, should work.