EDIT, SOLVED: I downloaded the most recent verson of Odin (3.14.1) and was able to get everything flashed. I was also using the normal CSC file and not the HOME_CSC file, which may have also contributed to the problem.
So I wanted to try out putting a custom firmware onto my Samsung Galaxy Tab S3 (SM-T820). I managed to install LineageOS 17 successfully via TWRP, but after trying it out for a bit decided I didn't like the tradeoffs and wanted to go back to stock.
Well now I'm having some trouble getting the stock ROM flashed back onto the system. Long story short:
TWRP recovery boot is still working
LineageOS has been wiped and the internal storage re-formatted
I have downloaded several different stock ROMs and now identified what I am relatively confident is the correct one (SM-T820_1_20200501145641_h0dxr2w1l3_fac, region code XAR for USA), although it only includes the BL, AP, and CSC files (not CP, none of the stock roms I found included a CP file though)
I have all the Samsung drivers installed onto my computer
I have Odin v3.10.7 on my computer (used it to install TWRP to get LineageOS installed)
When I select the BL, AP, and CSC files in Odin and try to run it while my tablet is in download mode, this is the output I get:
<ID:0/006> Added!!
<ID:0/006> Removed!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> emmc_appsboot.mbn.lz4
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
I have been on Google for quite some time and tried several things, but I haven't been able to make any progress. Most of the advice for the errors I found seem to relate to making sure I have the right ROM, but I've tried several different versions and finally downloaded the one I have through SamFirm so I don't think I have an incorrect ROM.
Related
Good day fellas,
I sold my S advance and get S2,
my friend 'updated' to 4.0.3 and it sucks and sofa king slow.
I tried to revert back to GB 2.3.6 but failed.
I use Odin and download files from internet.
still nothing works, I cant even reset to 4.0.3
I just want to use my phone now.
doesnt matter what it takes GB or ICS or custom ROM
the phone still can go to download mode, but could not boot for now
I guess I already screw the OS.
Please need advise from you guy,
now being very sad cannot use my phone
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> APBOOT_I9100XWKK5_CL754841_REV02_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9100XWKK5_CL754841_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9100XXKI4_REV_02_CL1065910.tar.md5 is valid.
<OSM> GT-I9100-MULTI-CSC-OXXKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Rempit said:
Good day fellas,
I sold my S advance and get S2,
my friend 'updated' to 4.0.3 and it sucks and sofa king slow.
I tried to revert back to GB 2.3.6 but failed.
I use Odin and download files from internet.
still nothing works, I cant even reset to 4.0.3
I just want to use my phone now.
doesnt matter what it takes GB or ICS or custom ROM
the phone still can go to download mode, but could not boot for now
I guess I already screw the OS.
Please need advise from you guy,
now being very sad cannot use my phone
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> APBOOT_I9100XWKK5_CL754841_REV02_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9100XWKK5_CL754841_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9100XXKI4_REV_02_CL1065910.tar.md5 is valid.
<OSM> GT-I9100-MULTI-CSC-OXXKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
please follow these steps here http://androidflip.com/how-to-install-flash-firmware-on-samsung-galaxy-s-2-gt-i9100/
what steps did you do prior to flashing with odin. ?
Did you wipe chache and davik chache ?
did you do a reset/data format ?
flash your file with odin.
if these to steps did not work.
You need to go into recovery do a complete format of your internal sd, then flash with odin. it will work then.
saywhatt said:
please follow these steps here http://androidflip.com/how-to-install-flash-firmware-on-samsung-galaxy-s-2-gt-i9100/
Click to expand...
Click to collapse
I did follow all the step before. but it does not seems to work. btw, the link to those files inside the guide has been removed by hotfiles
Rempit said:
I did follow all the step before. but it does not seems to work. btw, the link to those files inside the guide has been removed by hotfiles
Click to expand...
Click to collapse
You can use the steps, but instead use another file from sammobile.com
Sent from my GT-I9300 using xda premium
Hello,
Last night I bricked my device, and was stuck at Boot logo Samsung Galaxy S4. I had tried to use my stock rooted back up and had the same result. Since TWRP was still intact I d/led a deoxded tw rom. Now the phone works but there is still files from the previous stock root. How do I wipe the slate clean start completely over as if I just purchased the phone? Also before I had tried to install the rom I had messed around with Odin and tried flashing SCH-I545_MDK_562219_Stock_Restore.tar.md5 and failed everytime.
Thanks
bump
Fail Condition
In Odin using VRUAMDK_NoWipe.tar.md5
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRUAMDK_NoWipe.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Removed!!
<ID:0/013> Get PIT for mapping..
<ID:0/013> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Anyone have an idea? Added pit file and still fails No idea what steps I should take next.
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
simonheros said:
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
Click to expand...
Click to collapse
it seems I flashed my International I9300 to a different device (SGH-I747)??? what does this mean? flashed SGH-I747 firmware in I9300? just want to make sure that what i understood is right because your post is making some confusion..
Can you tell me if your device is 16GB or 32GB or 64GB? pit file for all three of them is different. if you will use correct one than this should not fail.. i dont think that mtp has to do anything with odin but if it does than uninstall all the drivers that are currently install(your device drivers) and download and install samsung drivers from here: http://www.mediafire.com/?7iy79emc0bf1fb4 and then try to connect the device again.. I hope this helps you..
suyash1629 said:
it seems I flashed my International I9300 to a different device (SGH-I747)??? what does this mean? flashed SGH-I747 firmware in I9300? just want to make sure that what i understood is right because your post is making some confusion..
Can you tell me if your device is 16GB or 32GB or 64GB? pit file for all three of them is different. if you will use correct one than this should not fail.. i dont think that mtp has to do anything with odin but if it does than uninstall all the drivers that are currently install(your device drivers) and download and install samsung drivers from here: ----------- and then try to connect the device again.. I hope this helps you..
Click to expand...
Click to collapse
Thank you for the response.
Yes I flashed I747 firmware in I9300. I apologize for the poor wording. My device is 16 GB. The one from the thread I linked is said to be used by 16 GB variant, so I believe it works. (Passes)
I don't get that MTP driver error anymore, but now when I try to put a Bootloader in it says that it's an unsupported dev type.
A person got a similar problem here : s3forums.com/forum/galaxy-s3-help/5772-stuck-download-mode-diffrent-device-type-9300-sgh-i747 ( can't post link) but it appears to be bricked flat out...
simonheros said:
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
Click to expand...
Click to collapse
I think mate you should check if your bootloader in locked or unlocked. As you mention above about QualComm Secure boot :Enable. may be before you was using gt-i9300 firmware it must be unlocked but after you flashed wrong firmware may be your bootloader got locked.
try to download complete stock 4.3 firmware from sammobile.com for correct variant i.e GT-I9300.
Download it and extract it and you will get .tar files
download latest Odin ( google it ) and open it.
put your phone in download mode by pressing volume down + home key + power key for few deconds until download mode screen appear.
press volume up key to goto download mode. connect your phone to your computer and wait till it install all the necessary driver. if you drivers are not installed properly then you have to manually installe the driver for your phone. download galaxy toolkit for s3 from xda and install it. search for the folder name galaxy toolkit in your computer. basically it will be in c:/ drive. open that folder and you will find driver folder under it. Inside the driver folder there will .exe file of driver. but before installing disconnect your phone computer and then install the driver. after the installation of your driver plug in again and wait till it install all the drivers.
Inside odin you must have to see that there is COM ID in 1st box and below it is written attached. if you dont see that then your driver are not installed correctly. uninstall and install it again.
after the driver install click on AP and select the AP .tar file that we extracted after downloading. select the appropriate file associated with it.
click on start and wait few minutes till the process gets complete.
If all things goes right you may get your phone back again.
Mustakim_456 said:
I think mate you should check if your bootloader in locked or unlocked. As you mention above about QualComm Secure boot :Enable. may be before you was using gt-i9300 firmware it must be unlocked but after you flashed wrong firmware may be your bootloader got locked.
try to download complete stock 4.3 firmware from sammobile.com for correct variant i.e GT-I9300.
Download it and extract it and you will get .tar files
download latest Odin ( google it ) and open it.
put your phone in download mode by pressing volume down + home key + power key for few deconds until download mode screen appear.
press volume up key to goto download mode. connect your phone to your computer and wait till it install all the necessary driver. if you drivers are not installed properly then you have to manually installe the driver for your phone. download galaxy toolkit for s3 from xda and install it. search for the folder name galaxy toolkit in your computer. basically it will be in c:/ drive. open that folder and you will find driver folder under it. Inside the driver folder there will .exe file of driver. but before installing disconnect your phone computer and then install the driver. after the installation of your driver plug in again and wait till it install all the drivers.
Inside odin you must have to see that there is COM ID in 1st box and below it is written attached. if you dont see that then your driver are not installed correctly. uninstall and install it again.
after the driver install click on AP and select the AP .tar file that we extracted after downloading. select the appropriate file associated with it.
click on start and wait few minutes till the process gets complete.
If all things goes right you may get your phone back again.
Click to expand...
Click to collapse
Thank you for the response.
Drivers work and it's been able to connect to ODIN but it fails regardless of the stock firmware I flash via PDA.
I get this :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLH1_I9300OLBBLH1_I9300DXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
For Bootloader
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----
It would help to mention that I have a second i9300 that works and hasn't been touched or anything. Can I do something with that?
edit* It says unsupported dev type on my screen when it fails..
simonheros said:
Thank you for the response.
Drivers work and it's been able to connect to ODIN but it fails regardless of the stock firmware I flash via PDA.
I get this :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLH1_I9300OLBBLH1_I9300DXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
For Bootloader
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----
It would help to mention that I have a second i9300 that works and hasn't been touched or anything. Can I do something with that?
edit* It says unsupported dev type on my screen when it fails..
Click to expand...
Click to collapse
Looks like your Nand maybe corrupt try flashing the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
tallman43 said:
Looks like your Nand maybe corrupt try flashing the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
Click to expand...
Click to collapse
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
SECURE CHECK FAIL : PIT
Unsupport: dev_type
---
None of the PIT's work now... And pretty much none of the files passed... D:
simonheros said:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
SECURE CHECK FAIL : PIT
Unsupport: dev_type
---
None of the PIT's work now... And pretty much none of the files passed... D:
Click to expand...
Click to collapse
Any progress??
suyash1629 said:
Any progress??
Click to expand...
Click to collapse
None what so-ever. I hit a dead end and had to get a replacement.
I'm just not going to mess with the new one anymore...
I have a S3 that received OTA and I updated. I am talking about a stock S3, no root, no changes. The phone died and I could not enter recovery mode. I can only enter the Odin Mode. I tried first with Keis in some computer and cables but Keis cannot recognize the phone.
I then tried ODIN 3.07 with a stock image but that didnt work. (see below, it says there is no pit partition). I also tried to repartition but it fails.
I tried ODIN in several computer and several cables as well, including a Windows XP.
This appear on the phone:
Code:
"Odin Mode
Product name: GT-I9300
Custom binary Download: no
Current Binary: Samsung Official
System Status: Custom".
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGND5_I9300EPLGNE1_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
This I tried later (re partition):
Code:
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas on how to fix this?
jsmith432 said:
I have a S3 that received OTA and I updated. I am talking about a stock S3, no root, no changes. The phone died and I could not enter recovery mode. I can only enter the Odin Mode. I tried first with Keis in some computer and cables but Keis cannot recognize the phone.
I then tried ODIN 3.07 with a stock image but that didnt work. (see below, it says there is no pit partition). I also tried to repartition but it fails.
I tried ODIN in several computer and several cables as well, including a Windows XP.
This appear on the phone:
Code:
"Odin Mode
Product name: GT-I9300
Custom binary Download: no
Current Binary: Samsung Official
System Status: Custom".
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGND5_I9300EPLGNE1_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
This I tried later (re partition):
Code:
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas on how to fix this?
Click to expand...
Click to collapse
Pit partition is corrupt try rescue firmware if that fails service center >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
tallman43 said:
Pit partition is corrupt try rescue firmware if that fails service center >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
Click to expand...
Click to collapse
Thanks for the tip, however, I guess it stuck on the pit partition again (1 hour already):
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
I'm currently having "Kernel is not Seandroid enforcing" error message.
First, I rooted my phone, then preparing into flashing a custom ROM and kernel.
I downloaded Extended battery (v 2.91.45) - N910C/H for Kernel and Nemesis for ROM.
Wipe cache and etc then flash the kernel via TWRP first while I was downloading the Custom ROM.
Rebooted after I flashed the Kernel (maybe I screwed up here because I don't have any ROM installed yet?)
Phone couldn't go anywhere past the boot screen which shown "Kernel is not Seandroid enforcing" error message.
After searching the internet, people suggested to flash the stock ROM via ODIN, but then I have these errors on Odin 3 v3.04
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910GDTU1COJ5_N910GOLB1COJ1_N910GDTU1COJ4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
And no response on Odin3 v3.12
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1205)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
I'm flashing with the latest stock ROM in my Country.
Tried different USB ports
Tried different USB cables.
Tried factory reset/ manual wipes
OS : 6.0.1
Model : SM-N910C - Samsung Note 4
What else can I do on my end before sending it to shops ?