Tab s6 stuck on "Samsung galaxy tab s6" logo - Samsung Galaxy Tab S6 Questions & Answers

Hi
yesterday my tab s6 screen got unresponsible without anything else happened..
Then i found out that if i used the pen - the n i could turn it off from drop down menu.
I did that but then when i tried to turn it on it got stuck on that bootloop!
I can not access recovery mode - only download mode.
When i put it on charge it starts booting without showing battery percent and boots over and over until battery is drained.
In download mode i tried to flash Bootloader and firmware - but no luck ( odin proceduce succeded but the tab is still in the same bootloop )..
Still can't reach recovery menu..
Any ideas?

Recovery Mode is tricky to get to on this tablet - The timings of the button presses are difficult to nail. Assuming you weren't trying to flash anything to your tablet prior to it boot looping, I don't see any reason why you couldn't access Recovery Mode.
Reboot Tab by pressing and holding both Power (Bixby) button and volume down. Once screen turns off immediately press Power and Volume Up, let go once you see Samsung logo.

bartleby999 said:
Recovery Mode is tricky to get to on this tablet - The timings of the button presses are difficult to nail. Assuming you weren't trying to flash anything to your tablet prior to it boot looping, I don't see any reason why you couldn't access Recovery Mode.
Reboot Tab by pressing and holding both Power (Bixby) button and volume down. Once screen turns off immediately press Power and Volume Up, let go once you see Samsung logo.
Click to expand...
Click to collapse
Tried again in 30min.. no luck :/
As soon as the screen gets dark the device restarts.. sometimes i manage to hold those buttons but still no reovery mode :/

egidsatr said:
Tried again in 30min.. no luck :/
As soon as the screen gets dark the device restarts.. sometimes i manage to hold those buttons but still no reovery mode :/
Click to expand...
Click to collapse
Have you done anything to your tablet prior to bootloop? Tried to flash anything, deleted anything?
Again, there's no reason you shouldn't be able to access Recovery this situation is exactly why it's there.

bartleby999 said:
Have you done anything to your tablet prior to bootloop? Tried to flash anything, deleted anything?
Again, there's no reason you shouldn't be able to access Recovery this situation is exactly why it's there.
Click to expand...
Click to collapse
I opened NBA 2K Mobile and then i went away for like 20mins..
Then i opened the tab and screen was not reacting - only with pen.
I think the USB debugging is not enabled - is there any ways how to enable it without rooting?
Just tried to install a firmware through download mode - Odin shows "passed" and my tab is still in the same sh** ..:/

Hi,
Really need your help, after I updated my firmware using Odin, updated BL, AP, CP, CSC, my tab cannot boot up stuck in logo. Doing the Power + volume up leads me to different screen now.
Cannot access recovery mode also.
What must I do? Pleasssee help. Added the pic, after doing hard reset (power + vol up)
I cannot connect back to Odin also. Always setup connection failed.
Please help. Messed up big time :'(
Thank you in advance.

JayR0503 said:
Hi,
Really need your help, after I updated my firmware using Odin, updated BL, AP, CP, CSC, my tab cannot boot up stuck in logo. Doing the Power + volume up leads me to different screen now.
Cannot access recovery mode also.
What must I do? Pleasssee help. Added the pic, after doing hard reset (power + vol up)
I cannot connect back to Odin also. Always setup connection failed.
Please help. Messed up big time :'(
Thank you in advance.
Click to expand...
Click to collapse
What country are you located in?

iBowToAndroid said:
What country are you located in?
Click to expand...
Click to collapse
UAE..

"setup connection failed" is a USB error. Try a different cable, or a different port on the computer, or a totally different computer

Related

Bricked S3

I flashed a kernel on my S3 via recovery and then reboot my phone. It goes to a black screen now. When I pull the battery and power on holding volume down to go into recovery the Samsung Galaxy S3 logo keeps appearing and disappearing until I let go of the volume down key. Then it's stuck at the same black screen. When I try to put the phone in download mode to re-flash via odin it does the same thing. I'm pretty sure I'm fu*ked, but I just want to make sure there's not a way to fix this. Any ideas?
Chaos Residue said:
I flashed a kernel on my S3 via recovery and then reboot my phone. It goes to a black screen now. When I pull the battery and power on holding volume down to go into recovery the Samsung Galaxy S3 logo keeps appearing and disappearing until I let go of the volume down key. Then it's stuck at the same black screen. When I try to put the phone in download mode to re-flash via odin it does the same thing. I'm pretty sure I'm fu*ked, but I just want to make sure there's not a way to fix this. Any ideas?
Click to expand...
Click to collapse
Don't worry..i have done worse things with my phone and yet to brick it..
Fist thing to go into recovery you hold vol up + power + home and not vol down..
Second thing what you will have to do is after the Odin flash..press and hold vol up+power+home..you will boot into the stock recovery..from here do a factory reset but mind you all the data on your internal sdcard will be lost when you do this..now reboot your phone..your phone will boot up properly now..assuming that you have flashed the firmware properly in Odin..
Chaos Residue said:
I flashed a kernel on my S3 via recovery and then reboot my phone. It goes to a black screen now. When I pull the battery and power on holding volume down to go into recovery the Samsung Galaxy S3 logo keeps appearing and disappearing until I let go of the volume down key. Then it's stuck at the same black screen. When I try to put the phone in download mode to re-flash via odin it does the same thing. I'm pretty sure I'm fu*ked, but I just want to make sure there's not a way to fix this. Any ideas?
Click to expand...
Click to collapse
As zoot1 replied to you for download mode press vol down+home+power for a few seconds......for recovery vol up+home+power.........
And make very sure the kernel you flash is compatible with your phone and firmware!!!!!!!!!!!! The rest zoot1 explained in his reply
Good luck
Sorta Bricked
Anyone have an idea what I've done.... Black screen with blue light. I can get to the recovery menu, clockwork is installed, but I can't flash a rom. The only way to get the phone to stay off is by removing the battery.
This is a Cspire L710. I've attempted to flash a Cspire_nandroid_stock zip, the phone will find it but can't open it. I missed a step somewhere I guess. I had it in download mode but made the mistake of trying the factory reset-which changed that.
I've also tried a couple of other roms with the same results.
db1117 said:
Anyone have an idea what I've done.... Black screen with blue light. I can get to the recovery menu, clockwork is installed, but I can't flash a rom. The only way to get the phone to stay off is by removing the battery.
This is a Cspire L710. I've attempted to flash a Cspire_nandroid_stock zip, the phone will find it but can't open it. I missed a step somewhere I guess. I had it in download mode but made the mistake of trying the factory reset-which changed that.
I've also tried a couple of other roms with the same results.
Click to expand...
Click to collapse
go to download mode and flash a stock rom via odin
Cant's get to Download mode
Unless there is a way to get to download mode through the recovery menu, download mode is not an option.
db1117 said:
Unless there is a way to get to download mode through the recovery menu, download mode is not an option.
Click to expand...
Click to collapse
Well i suggest u send it with its warranty or u could check out my sig and build ur own usb jig
Sent from my GT-I9300 using xda premium
You might be able to get to download mode via a usb jig.

Flashed Wrong Recovery - CWM and Download mode don't work

I tried to Unroot my Galaxy Tab 10.1 LTE last night and think I may have bricked my tablet. I used the instructions here on the XDA forum which had a link to all the Stock ROM's in one place. I got the most recent one and the only one for USA but it said it was for the model 7510. I didn't think that would be a problem since the USB drivers I installed on my PC were also labeled as being for the 7510 and they worked.
This tablet is the SCH-I905. Now I can't get it to boot at all. Gets stuck in a boot loop. Shows the Samsung logo, then resets and does it again. I can't get it in recovery mode either. Goes to a black screen and hangs.
Using the normal process to get to Download mode doesn't work. Holding Power and Volume Up, then letting go of the Power button, then pressing Volume Down and then Up. That's one weird thing. I can get to the option screen that shows the Download and Recovery mode options. Normally I would hit the Volume Down button to select Download mode and on the screen it says to press Volume Up to continue or Volume Down to cancel. If I press Volume Up it goes to a black screen and hangs. If I press Volume Down I get the Odin Download screen that says Waiting on USB cable.
That screen doesn't look the same as what I normally see but I'm not sure what's different. I didn't memorize each line of text. I just know there's not as much text there as there usually is. My PC will not recognize the tablet no matter which USB port I try to use and the tablet doesn't recognize that the USB cable is plugged in. I had no problem with the USB connection before I flashed the 7510 stock ROM.
So, if I cannot get to recovery mode and I can't get Download mode to work so I can use Odin to flash a different rom then is this thing bricked or is there something else I can try? I am about to try using my laptop and its USB ports but I don't think that's going to make any difference.
BTW, I have since found the correct 'stock recovery rom' at droidbasement.com and downloaded it to my PC. I just need to get on the tablet somehow.
Many people have your problem. I have my Lte verizon bricked as yours. The problem is demaged bootloader, only nvflash can fix it but actually our bootloader is locked and we need a hex key called sbk. At least we have to wait that somebody hack our tab from the basement. For now we can only search and share result.
pickupcash said:
I tried to Unroot my Galaxy Tab 10.1 LTE last night and think I may have bricked my tablet. I used the instructions here on the XDA forum which had a link to all the Stock ROM's in one place. I got the most recent one and the only one for USA but it said it was for the model 7510. I didn't think that would be a problem since the USB drivers I installed on my PC were also labeled as being for the 7510 and they worked.
This tablet is the SCH-I905. Now I can't get it to boot at all. Gets stuck in a boot loop. Shows the Samsung logo, then resets and does it again. I can't get it in recovery mode either. Goes to a black screen and hangs.
Using the normal process to get to Download mode doesn't work. Holding Power and Volume Up, then letting go of the Power button, then pressing Volume Down and then Up. That's one weird thing. I can get to the option screen that shows the Download and Recovery mode options. Normally I would hit the Volume Down button to select Download mode and on the screen it says to press Volume Up to continue or Volume Down to cancel. If I press Volume Up it goes to a black screen and hangs. If I press Volume Down I get the Odin Download screen that says Waiting on USB cable.
That screen doesn't look the same as what I normally see but I'm not sure what's different. I didn't memorize each line of text. I just know there's not as much text there as there usually is. My PC will not recognize the tablet no matter which USB port I try to use and the tablet doesn't recognize that the USB cable is plugged in. I had no problem with the USB connection before I flashed the 7510 stock ROM.
So, if I cannot get to recovery mode and I can't get Download mode to work so I can use Odin to flash a different rom then is this thing bricked or is there something else I can try? I am about to try using my laptop and its USB ports but I don't think that's going to make any difference.
BTW, I have since found the correct 'stock recovery rom' at droidbasement.com and downloaded it to my PC. I just need to get on the tablet somehow.
Click to expand...
Click to collapse
Did you solved the issue?
Please share ..., i face the same problem now ...
regards,
erwien.
Did you solved the issue.
share me......i face the same problem now
.
.
.
.
.
.
.
.
.
.
.
.
help me plz

Help! Phone won't stop rebooting! S6 edge sm-g925i

I woke up yesterday and found my phone dead.
It keeps rebooting and I am stuck on the Samsung logo screen.
The notification light on the upper left side stays on when the phone has power.
I am NOT able to get in recovery mode, but I can get in download mode.
Holding the power button won't turn off the phone, I have to hold volume down + power button to turn it off.
Things that I've tried:
1. Kies and Smartswitch (Succeed! But the phone won't go further than the Samsung logo screen and it continues to reboot and reboot)
2. flashing firmware downloaded from sammobile with odin (I've downloaded 3 firmwares, two 6.01 and one 5.11, the two 6.01 work, it says "PASSED," then my phone reboots and it's all the same. It won't go further than the logo screen. The 5.11 one doesn't work)
3. flashing stock recovery and twrp with odin, ( i tried a few versions of those, the worked ones say "PASSED," but I then get recovery is not seandroid enforcing or no message at all, either way I am still not able to get into recovery mode
Please Help!:crying::crying:
cigar621 said:
I woke up yesterday and found my phone dead.
It keeps rebooting and I am stuck on the Samsung logo screen.
The notification light on the upper left side stays on when the phone has power.
I am NOT able to get in recovery mode, but I can get in download mode.
Holding the power button won't turn off the phone, I have to hold volume down + power button to turn it off.
Things that I've tried:
1. Kies and Smartswitch (Succeed! But the phone won't go further than the Samsung logo screen and it continues to reboot and reboot)
2. flashing firmware downloaded from sammobile with odin (I've downloaded 3 firmwares, two 6.01 and one 5.11, the two 6.01 work, it says "PASSED," then my phone reboots and it's all the same. It won't go further than the logo screen. The 5.11 one doesn't work)
3. flashing stock recovery and twrp with odin, ( i tried a few versions of those, the worked ones say "PASSED," but I then get recovery is not seandroid enforcing or no message at all, either way I am still not able to get into recovery mode
Please Help!:crying::crying:
Click to expand...
Click to collapse
Flash the stock 6.0.1 firmware that passes before. When phone is bootlooping hold only POWER AND VOL DOWN. This will power off and boot into safe mode. As soon as it powers on hold HOME POWER AND UP. So you need to hold down and power then as soon as it goes off and boots to galaxy s6 edge powered by android press vol up aswell this should get you to recovery. Wipe data and cache and it should boot up. Keep me updated
callumbr1 said:
Flash the stock 6.0.1 firmware that passes before. When phone is bootlooping hold only POWER AND VOL DOWN. This will power off and boot into safe mode. As soon as it powers on hold HOME POWER AND UP. So you need to hold down and power then as soon as it goes off and boots to galaxy s6 edge powered by android press vol up aswell this should get you to recovery. Wipe data and cache and it should boot up. Keep me updated
Click to expand...
Click to collapse
The logo faded and nothing happened, do I keep holding the volume up and home till something happens?
cigar621 said:
The logo faded and nothing happened, do I keep holding the volume up and home till something happens?
Click to expand...
Click to collapse
Sorry...
Hold only vol down + power
Once screen goes off and powered by android comes on
Switch to vol up + power + home and keep holding till recovery boots
callumbr1 said:
Sorry...
Hold only vol down + power
Once screen goes off and powered by android comes on
Switch to vol up + power + home and keep holding till recovery boots
Click to expand...
Click to collapse
See if the charger cable is connected, holding the vol down+power button wouldn't shut down the phone (or maybe it shuts it down but it just reboots itself up immediately again)
I held the vol down+power button, and switched to holding the vol up+home button+power when I saw the logo came up, and while I was holding them, the logo faded and all I had is a black screen. I kept holding it anyway for 2 minutes, nothing happened. :crying:
please advise
cigar621 said:
See if the charger cable is connected, holding the vol down+power button wouldn't shut down the phone (or maybe it shuts it down but it just reboots itself up immediately again)
I held the vol down+power button, and switched to holding the vol up+home button+power when I saw the logo came up, and while I was holding them, the logo faded and all I had is a black screen. I kept holding it anyway for 2 minutes, nothing happened. :crying:
please advise
Click to expand...
Click to collapse
Down and power boots to safe mode, as soon as screen goes off and boots back up recovery combination should work. What region are you in? What firmware did you flash on 6.0.1?
callumbr1 said:
Down and power boots to safe mode, as soon as screen goes off and boots back up recovery combination should work. What region are you in? What firmware did you flash on 6.0.1?
Click to expand...
Click to collapse
I just used Kies to get the official firmware in it again. I am in the US. My phone though is an international version of the S6 edge SM-G925I.
I tried to flash a Stock Recovery in it with odin again since I just couldn't get in recovery and it failed!! I got it in last time when I was on the G925IDVS3EPIF_G925IOPS3EPGG_G925IDVU3EPIA_HOME.tar.md5 firmware
cigar621 said:
I just used Kies to get the official firmware in it again. I am in the US. My phone though is an international version of the S6 edge SM-G925I.
I tried to flash a Stock Recovery in it with odin again since I just couldn't get in recovery and it failed!! I got it in last time when I was on the G925IDVS3EPIF_G925IOPS3EPGG_G925IDVU3EPIA_HOME.tar.md5 firmware
Click to expand...
Click to collapse
Is your phone locked to a network?
---------- Post added at 06:11 AM ---------- Previous post was at 06:07 AM ----------
cigar621 said:
I just used Kies to get the official firmware in it again. I am in the US. My phone though is an international version of the S6 edge SM-G925I.
I tried to flash a Stock Recovery in it with odin again since I just couldn't get in recovery and it failed!! I got it in last time when I was on the G925IDVS3EPIF_G925IOPS3EPGG_G925IDVU3EPIA_HOME.tar.md5 firmware
Click to expand...
Click to collapse
http://www.sammobile.com/firmwares/download/101961/G925IDVS3EPIF_G925IXSA3EPGG_XSA/
Download and flash this through odin. If your not sure how let me know ill give you steps
I am having the same problem on a G925T.
shinta86 said:
I am having the same problem on a G925T.
Click to expand...
Click to collapse
What region? Is phone unlocked?
callumbr1 said:
Is your phone locked to a network?
---------- Post added at 06:11 AM ---------- Previous post was at 06:07 AM ----------
http://www.sammobile.com/firmwares/download/101961/G925IDVS3EPIF_G925IXSA3EPGG_XSA/
Download and flash this through odin. If your not sure how let me know ill give you steps
Click to expand...
Click to collapse
This is the one that I downloaded before. I extracted the zip, put the phone into download mode and connected it to the pc. Open Odin, press AP and chose the extracted file., "start". It passed and rebooted. But I am still stuck on the logo screen.
I also tried to separate the firmware files into AP and BL with script, it also passed, but I am still stuck!
What should I do?
cigar621 said:
This is the one that I downloaded before. I extracted the zip, put the phone into download mode and connected it to the pc. Open Odin, press AP and chose the extracted file., "start". It passed and rebooted. But I am still stuck on the logo screen.
I also tried to separate the firmware files into AP and BL with script, it also passed, but I am still stuck!
What should I do?
Click to expand...
Click to collapse
Try a different one from different region. Can you still not get into recovery mode?
callumbr1 said:
Try a different one from different region. Can you still not get into recovery mode?
Click to expand...
Click to collapse
I tried two g925I from india
One g925i from Australia (Optus)
One g925I from Australia (the latest two on the sammmobile site0
the kies, the smartswitch
all of them succeeded.
but i just can't get into recovery mode. I tried to flash stock recovery in it, even when it succeeded, i still can't get in recovery mode.
I tried flashing twrp too, it succeeded but there's "recovery is not seandroid enforcing" on the screen
when I tried a G925F one, it says "secure check fail <bootloader>" on the phone
now when i get into download mode, there are two lines at the bottom saying:
knox warranty void:1 (0x030c)
RP SWREV: B:3 K:2 S:2
cigar621 said:
I tried two g925I from india
One g925i from Australia (Optus)
One g925I from Australia (the latest two on the sammmobile site0
the kies, the smartswitch
all of them succeeded.
but i just can't get into recovery mode. I tried to flash stock recovery in it, even when it succeeded, i still can't get in recovery mode.
I tried flashing twrp too, it succeeded but there's "recovery is not seandroid enforcing" on the screen
when I tried a G925F one, it says "secure check fail <bootloader>" on the phone
now when i get into download mode, there are two lines at the bottom saying:
knox warranty void:1 (0x030c)
RP SWREV: B:3 K:2 S:2
Click to expand...
Click to collapse
Yeah they will always show up in download mode.
Try to flash one again, but uncheck auto reboot in odin, after flashing try to boot into recovery. How long did you leave it booting for? Sometimes first boot after flash can take up to 30 minutes.
If not keep trying the combo i said...
Power and down until phone reboots.
As soon as screen comes back on powered by android hold vol up home and power.
You have to be quick with it you have to get the recovery buttons as soon as it boots.
Or try boot into download mode, then as soon as you press up to cancel it phone will boot, as soon as you press cancel do recovery combo
callumbr1 said:
What region? Is phone unlocked?
Click to expand...
Click to collapse
US and no.
shinta86 said:
US and no.
Click to expand...
Click to collapse
What network are you on?
callumbr1 said:
What network are you on?
Click to expand...
Click to collapse
Tmobile
shinta86 said:
Tmobile
Click to expand...
Click to collapse
http://www.sammobile.com/firmwares/download/89343/G925TUVS4EPH2_G925TTMB4EPH2_TMB/
Download and flash this
callumbr1 said:
http://www.sammobile.com/firmwares/download/89343/G925TUVS4EPH2_G925TTMB4EPH2_TMB/
Download and flash this
Click to expand...
Click to collapse
package fails md5sum validation
shinta86 said:
package fails md5sum validation
Click to expand...
Click to collapse
Delete the .md5 so its just .tar

Download Mode note getting

Hii Friends,
Im using samsung mega 6.3. (GT-I9200)
im trying to update my mobile via odin. but when i try to enter download mode its not entering .
Please help me
(Volume down + home button+power button )
Dag_Nab.It
S/G MEGA 6.3 (AT&T-US) SGH-i527~GT-i9205
I have the same issue with my device not entering Download Mode. My device will ONLY go to main screen asking for password, which I no longer remember.
please help us
Still_Kicking...
VolumeUP+Home+Power, still getting 'no response' while holding all three down and releasing at start up.
*i forgot to mention that after StartUp, on the Enter Password request page, only the Power button operates. the VolumeUp, VolumeDown, and Home buttons do nothing. I have to press Power button after the screen has blacked out to bring-up the Enter Password request page again.
Today, I installed an old SIM card (SIM not provisioned MM#2) is displayed. I'll have to research this for the meaning as this is a first for me.
This time I held VolumeDown+Home buttons throughout the StartUp process. This time, on the Enter Password request page, in the lower left corner, Safe mode is stated. Anyone have some tips on what we can do while the device is in this mode as I have yet to read anything on Safe mode for any of the devices listed so far?
TO ENTER Safe mode:
Hold Power button until device starts up, release. Now hold down VolumeDown+Home buttons until Enter Password request page shows. The device should now state that its in Safe mode in the lower left corner. Please take note that this is on the S/G MEGA 6.3 (AT&T-US) SGH-i527~GT-i9205.
Galaxy Mega 6.3/ Black screen after ROM Flash
A friend of mine gave me his Galaxy Mega 6.3 as when he previously did something with the phones software, he messed something up and lost imei numbers, wifi and bluetooth wouldn't work however the phone would still turn on. Just like an MP3 player.
I struggle around a day to get this phone into download mode in order to flash its factory rom and i finally got the phone to download mode, i flashed the correct I9205 stock rom on and now the phone wont turn on.
No buttons light up including the blue LED at the top. The screen turns on and back off after a few seconds. No logo appears, but the phone does respond to the power button. Its like a bootloop but it loops before it gets to any sort of logo screen. I cant seem to launch to any sort of safe mode, recovery mode or download mode and the phone is not detected on my computer.
Any ideas on how to get this backup and running.
0Waiser0 said:
A friend of mine gave me his Galaxy Mega 6.3 as when he previously did something with the phones software, he messed something up and lost imei numbers, wifi and bluetooth wouldn't work however the phone would still turn on. Just like an MP3 player.
I struggle around a day to get this phone into download mode in order to flash its factory rom and i finally got the phone to download mode, i flashed the correct I9205 stock rom on and now the phone wont turn on.
No buttons light up including the blue LED at the top. The screen turns on and back off after a few seconds. No logo appears, but the phone does respond to the power button. Its like a bootloop but it loops before it gets to any sort of logo screen. I cant seem to launch to any sort of safe mode, recovery mode or download mode and the phone is not detected on my computer.
Any ideas on how to get this backup and running.
Click to expand...
Click to collapse
Did you check the PDA, CSC, and of course the md5 to make sure you had the right Firmware(ROM)? Where did you download it from?
How did you get the device into download mode?
kidcrazie said:
Did you check the PDA, CSC, and of course the md5 to make sure you had the right Firmware(ROM)? Where did you download it from?
How did you get the device into download mode?
Click to expand...
Click to collapse
I managed to get the device to download mode via the normal method of pressing volume home and power however it doesnt always work and it just restarts continuesly. I got the rom from sammobiles or something like that and i believe its the correct one. I have tried several other roms that is for mega 6.3 but no hope. However i did manage to get twrp installed. Do you by any chance know any os that you can link for me that i can install directly and only by using twrp installation?
0Waiser0 said:
I managed to get the device to download mode via the normal method of pressing volume home and power however it doesnt always work and it just restarts continuesly. I got the rom from sammobiles or something like that and i believe its the correct one. I have tried several other roms that is for mega 6.3 but no hope. However i did manage to get twrp installed. Do you by any chance know any os that you can link for me that i can install directly and only by using twrp installation?
Click to expand...
Click to collapse
There is LineageOS ROM with RR Remix. I have heard that you have to use Kies before you can use Odin3. Sorry for the late reply.
kidcrazie said:
There is LineageOS ROM with RR Remix. I have heard that you have to use Kies before you can use Odin3. Sorry for the late reply.
Click to expand...
Click to collapse
What if kies does not detect device.
0Waiser0 said:
What if kies does not detect device.
Click to expand...
Click to collapse
I understand the problem we are having but I haven't quite figured out a solution just yet. Even my PC isn't recognizing my device now. Don't know WTH!!!!

Get stuck on bootloop

I have unlockbootloader my v300k after i flash it to us998 to root it get bootloop and i cant get to fastboot or download. What can i do ? pls help mee
giabao574 said:
I have unlockbootloader my v300k after i flash it to us998 to root it get bootloop and i cant get to fastboot or download. What can i do ? pls help mee
Click to expand...
Click to collapse
Go to the Korea thread and see what they say?
giabao574 said:
I have unlockbootloader my v300k after i flash it to us998 to root it get bootloop and i cant get to fastboot or download. What can i do ? pls help mee
Click to expand...
Click to collapse
you don't know how to get into bootloader or you can't get into bootloader?
I cant get into bootloader . Because when i plug cabble into my phone it started to charge . I try with fastboot and download mode but it cant . I think my phone lost bootloader
giabao574 said:
I cant get into bootloader . Because when i plug cabble into my phone it started to charge . I try with fastboot and download mode but it cant . I think my phone lost bootloader
Click to expand...
Click to collapse
it - from time to time - shows the charging logo,
then just force it to reset: power button + volume down - keep both pressed until it resets (screen off),
then keep the volume down button pressed
<-- with the usb cable plugged in all of the time
That should get you into bootloader.
Note:
the phones behaves really weird and it could be that it shuts off while in bootloader.
In that case simply disconnect the USB cable, connect it to the phone only and then - while the volume button down is pressed - connect it to PC
zacharias.maladroit said:
it - from time to time - shows the charging logo,
then just force it to reset: power button + volume down - keep both pressed until it resets (screen off),
then keep the volume down button pressed
<-- with the usb cable plugged in all of the time
That should get you into bootloader.
Note:
the phones behaves really weird and it could be that it shuts off while in bootloader.
In that case simply disconnect the USB cable, connect it to the phone only and then - while the volume button down is pressed - connect it to PC
Click to expand...
Click to collapse
I tried so hard but it can't it always go to show charge logo and my pc cant recognize my phone .
Lg v30 Boot loop stuck no pc detection
My LG v30 suddenly stuck in Boot loop there is no sign of dection in the PC. All combination of buttones tried but all in vain.
Any trick please
LG V30 bootloop
amarsaeed said:
My LG v30 suddenly stuck in Boot loop there is no sign of dection in the PC. All combination of buttones tried but all in vain.
Any trick please
Click to expand...
Click to collapse
Hi, I seem to have the same problem... the phone loops the startup screen and the USB connection is not working. I can get the initial download mode screen to appear for a minute, the looping starts again.
I think I have a brick...
hammeru said:
Hi, I seem to have the same problem... the phone loops the startup screen and the USB connection is not working. I can get the initial download mode screen to appear for a minute, the looping starts again.
I think I have a brick...
Click to expand...
Click to collapse
have you tried Master Reset?
ChazzMatt said:
have you tried Master Reset?
Click to expand...
Click to collapse
MAJOR EDIT: Master Reset worked, is accessed by holding vol down and power until screen goes dark, release power when the lg logo appears, count to 2, press power again until factory reset screen, say yes, should put you into twrp (provided you already have it installed of course)
Is there a button combination to do this? I'm fearing I also bricked my us998 by dirty flashing from aospx to the johnfawkes stock rom after I randomly stopped getting lte connection. Probably definitely should have factory reset but there were a few pictures I didn't want to lose and now I am really wishing I had bitten the bullet on them to save my phone. Current situation is a loop at the verizon startup screen, vol down and power can initiate a restart and from there I can hold vol up to get the initial download mode splash screen but then the screen goes dark and the device starts to loop again. Any suggestions would be greatly appreciated.
rollthedaisuke said:
MAJOR EDIT: Master Reset worked, is accessed by holding vol down and power until screen goes dark, release power when the lg logo appears, count to 2, press power again until factory reset screen, say yes, should put you into twrp (provided you already have it installed of course).
Click to expand...
Click to collapse
Glad you got it figured out.

Categories

Resources